New Insights towards High-Temperature Ethanol-Sensing Mechanism of ZnO-Based Chemiresistors.

In this work, we investigate ethanol (EtOH)-sensing mechanisms of a ZnO nanorod (NRs)-based chemiresistor using a near-ambient-pressure X-ray photoelectron spectroscopy (NAP-XPS). First, the ZnO NRs-based sensor was constructed, showing good performance on interaction with 100 ppm of EtOH in the ambient air at 327 °C. Then, the same ZnO NRs film was investigated by NAP-XPS in the presence of 1 mbar oxygen, simulating the ambient air atmosphere and O2/EtOH mixture at the same temperature. The partial pressure of EtOH was 0.1 mbar, which corresponded to the partial pressure of 100 ppm of analytes in the ambient air. To better understand the EtOH-sensing mechanism, the NAP-XPS spectra were also studied on exposure to O2/EtOH/H2O and O2/MeCHO (MeCHO = acetaldehyde) mixtures. Our results revealed that the reaction of EtOH with chemisorbed oxygen on the surface of ZnO NRs follows the acetaldehyde pathway. It was also demonstrated that, during the sensing process, the surface becomes contaminated by different products of MeCHO decomposition, which decreases dc-sensor performance. However, the ac performance does not seem to be affected by this phenomenon.

Polypyrrole Nanotubes and Their Carbonized Analogs: Synthesis, Characterization, Gas Sensing Properties.

Polypyrrole (PPy) in globular form and as nanotubes were prepared by the oxidation of pyrrole with iron(III) chloride in the absence and presence of methyl orange, respectively. They were subsequently converted to nitrogen-containing carbons at 650 °C in an inert atmosphere. The course of carbonization was followed by thermogravimetric analysis and the accompanying changes in molecular structure by Fourier Transform Infrared and Raman spectroscopies. Both the original and carbonized materials have been tested in sensing of polar and non-polar organic vapors. The resistivity of sensing element using globular PPy was too high and only nanotubular PPy could be used. The sensitivity of the PPy nanotubes to ethanol vapors was nearly on the same level as that of their carbonized analogs (i.e., ~18% and 24%, respectively). Surprisingly, there was a high sensitivity of PPy nanotubes to the n-heptane vapors (~110%), while that of their carbonized analog remained at ~20%. The recovery process was significantly faster for carbonized PPy nanotubes (in order of seconds) compared with 10 s of seconds for original nanotubes, respectively, due to higher specific surface area after carbonization.

Surface Enhancement Using Black Coatings for Sensor Applications.

The resolution of a quartz crystal microbalance (QCM) is particularly crucial for gas sensor applications where low concentrations are detected. This resolution can be improved by increasing the effective surface of QCM electrodes and, thereby, enhancing their sensitivity. For this purpose, various researchers have investigated the use of micro-structured materials with promising results. Herein, we propose the use of easy-to-manufacture metal blacks that are highly structured even on a nanoscale level and thus provide more bonding sites for gas analytes. Two different black metals with thicknesses of 280 nm, black aluminum (B-Al) and black gold (B-Au), were deposited onto the sensor surface to improve the sensitivity following the Sauerbrey equation. Both layers present a high surface roughness due to their cauliflower morphology structure. A high response (i.e., resonant frequency shift) of these QCM sensors coated with a black metal layer was obtained. Two gaseous analytes, H2O vapor and EtOH vapor, at different concentrations, are tested, and a distinct improvement of sensitivity is observed for the QCM sensors coated with a black metal layer compared to the blank ones, without strong side effects on resonance frequency stability or mechanical quality factor. An approximately 10 times higher sensitivity to EtOH gas is reported for the QCM coated with a black gold layer compared to the blank QCM sensor.

In Situ Monitoring of Pulsed Laser Annealing of Eu-Doped Oxide Thin Films.

Eu3+-doped oxide thin films possess a great potential for several emerging applications in optics, optoelectronics, and sensors. The applications demand maximizing Eu3+ photoluminescence response. Eu-doped ZnO, TiO2, and Lu2O3 thin films were deposited by Pulsed Laser Deposition (PLD). Pulsed UV Laser Annealing (PLA) was utilized to modify the properties of the films. In situ monitoring of the evolution of optical properties (photoluminescence and transmittance) at PLA was realized to optimize efficiently PLA conditions. The changes in optical properties were related to structural, microstructural, and surface properties characterized by X-ray diffraction (XRD) and atomic force microscopy (AFM). The substantial increase of Eu3+ emission was observed for all annealed materials. PLA induces crystallization of TiO2 and Lu2O3 amorphous matrix, while in the case of already nanocrystalline ZnO, rather surface smoothening0related grains' coalescence was observed.

Phthalocyanine Photoregeneration for Low Power Consumption Chemiresistors.

It is well-known that the applicability of phthalocyanine chemiresistors suffers from long recovery time after NO2 exposure. This circumstance enforces the necessity to operate the sensors at elevated temperatures (150-200 °C), which shortens the sensor lifetime and increases its power consumption (regardless, a typical measurement period is longer than 15 min). In this paper, we propose a new method for fast and effective recovery by UV-vis illumination at a low temperature (55 °C). The method is based on short illumination following short NO2 exposure. To support and optimize the method, we investigated the effects of light in the wavelength and intensity ranges of 375-850 nm and 0.2-0.8 mW/mm2, respectively, on the rate of NO2 desorption from the phthalocyanine sensitive layer during the recovery period. This investigation was carried out for a set of phthalocyanine materials (ZnPc, CuPc, H2Pc, PbPc, and FePc) operating at slightly elevated temperatures (55-100 °C) and was further supported by the analysis of UV-vis and FTIR spectral changes. We found out that the light with the wavelength shorter than 550 nm significantly accelerates the NO2 desorption from ZnPc, CuPc, and FePc, and allows bringing the measurement period under 2 min and decreasing the sensor power consumption by 75%. Possible mechanisms of the light-stimulated desorption are discussed.