Analysis of the effect of organic solvent-sheet interfacial interaction on the exfoliation of sulfur-doped reduced graphene oxide sheets in a solvent system using molecular dynamics simulations.

In this study, the effect of interfacial interaction between solvent and sheets on the exfoliation of sulfur-doped reduced graphene oxide (SrGO) sheets was studied, using molecular dynamics simulations. Four organic solvents of toluene, tetrahydrofuran, N-methyl-2-pyrrolidone, and sulfolane, were used in this simulation. An insertion simulation considering the size effect of insertion molecules was used to determine the insertion efficiency of the solvent molecules. The insertion efficiency of toluene was the best among the four solvents due to the influence of the effective thickness of the solvent. An exfoliation simulation considering electrostatic interaction was conducted to evaluate the exfoliation efficiency of the SrGO sheets. Unlike the insertion efficiency case, the sulfolane was found to have the best exfoliation efficiency among the four solvents, due to the strong electrostatic repulsion and weak attractive energy between the SrGO sheets. The exfoliation efficiency of the SrGO sheets was improved by increasing the sulfur content and the ratio of the thiol type to the total number of sulfur-doped groups. These results reveal that decreasing the attractive energy and increasing the electrostatic repulsion between the solvent and SrGO sheets are a useful way to improve the exfoliation efficiency of SrGO sheets.

Influences of carboxyl functionalization of intercalators on exfoliation of graphite oxide: a molecular dynamics simulation.

In this study, the influences of the carboxyl functionalization of intercalators on exfoliation of graphite oxide were analyzed using molecular dynamics (MD) simulations. Molecular models of four-layered graphene oxide (GO) sheets, four different solvents (ethanol, dimethylformamide, tetrahydrofuran, and N-methyl-2-pyrrolidone), and four different intercalators (anthracene, 2-anthracenecarboxylic acid, 2,3-anthracenedicarboxylic acid, and 2,6-anthracenedicarboxylic acid) were used in the MD simulations. A separation simulation of GO sheets was performed to determine the point at which the GO sheets begin to exfoliate. An insertion simulation was used to obtain the minimum kinetic energy required for exfoliation and to calculate GO-solvent and GO-intercalator interaction energies. As the simulation result, GO-solvent and GO-intercalator interactions affected the minimum kinetic energy required for exfoliation. Having more carboxyl functional groups on the anthracene improved both the GO-intercalator interaction and the efficiency of the intercalators during exfoliation. These results reveal that increasing the interaction energy between the GO sheets and the insertion molecules is an efficient way to improve the performance of the solvents and the intercalators for the exfoliation of GO sheets.

Defect healing of reduced graphene oxide via intramolecular cross-dehydrogenative coupling.

A chemical defect healing of reduced graphene oxide (RGO) was carried out via intramolecular cross-dehydrogenative coupling (ICDC) with FeCl3 at room temperature. The Raman intensity ratio of the G-band to the D-band, the IG/ID ratio, of the RGO was increased from 0.77 to 1.64 after the ICDC reaction. From XPS measurements, the AC=C/AC-C ratio, where the peak intensities from the C=C and C-C bonds are abbreviated as AC=C and AC-C, of the RGO was increased from 2.88 to 3.79. These results demonstrate that the relative amount of sp(2)-hybridized carbon atoms is increased by the ICDC reaction. It is of great interest that after the ICDC reaction the electrical conductivity of the RGO was improved to 71 S cm(-1), which is 14 times higher than that of as-prepared RGO (5 S cm(-1)).

Effects on the Thermo-Mechanical and Interfacial Performance of Newly Developed PI-Sized Carbon Fiber-Polyether Ether Ketone Composites: Experiments and Molecular Dynamics Simulations.

In this study, polyether ether ketone (PEEK) composites reinforced with newly developed water-dispersible polyimide (PI)-sized carbon fibers (CFs) were developed to enhance the effects of the interfacial interaction between PI-sized CFs and a PEEK polymer on their thermo-mechanical properties. The PI sizing layers on these CFs may be induced to interact vigorously with the p-phenylene groups of PEEK polymer chains because of increased electron affinity. Therefore, these PI-sized CFs are effective for improving the interfacial adhesion of PEEK composites. PEEK composites were reinforced with C-CFs, de-CFs, and PI-sized CFs. The PI-sized CFs were prepared by spin-coating a water-dispersible PAS suspension onto the de-CFs, followed by heat treatment for imidization. The composites were cured using a compression molding machine at a constant temperature and pressure. Atomic force and scanning electron microscopy observations of the structures and morphologies of the carbon fiber surfaces verified the improvement of their thermo-mechanical properties. Molecular dynamics simulations were used to investigate the effects of PI sizing agents on the stronger interfacial interaction energy between the PI-sized CFs and the PEEK polymer. These results suggest that optimal amounts of PI sizing agents increased the interfacial properties between the CFs and the PEEK polymer.

Coatable Negative Dispersion Retarder: Kinetically Controlled Self-Assembly Pathway of Butterfly-Shaped Molecular Building Blocks for the Construction of Nanocolumns.

Disc-shaped building blocks with columnar phases have attracted attention for their potential in optical applications, including a retarder. However, to achieve coatable high-performance optical films, it is essential to understand a subtle interaction balance between building blocks and relevant self-assembled behaviors during material processing. Herein, we studied a self-assembled nanocolumn evaluation of linear butterfly-shaped dendrons (T-A3D) consisting of thiophene-based conjugated core and flexible alkyl dendron. X-ray diffraction provided insight into the unique hexagonal columnar liquid crystal phase of T-A3D, driven by intermolecular hydrogen bonding and coplanarity of the thiophene-based conjugated core. The formation of a self-assembled nanocolumn with high mobility enabled the uniaxial orientation of butterfly-shaped T-A3D on the aligned rod-shaped nematic reactive mesogens, resulting in a transparent and colorless two-layered negative retarder. The self-assembled nanocolumn consisting of butterfly-shaped molecule would break a new ground for developing advanced optical thin films.

Long-wave infrared transparent sulfur polymers enabled by symmetric thiol cross-linker.

Infrared (IR) transmissive polymeric materials for optical elements require a balance between their optical properties, including refractive index (n) and IR transparency, and thermal properties such as glass transition temperature (Tg). Achieving both a high refractive index (n) and IR transparency in polymer materials is a very difficult challenge. In particular, there are significant complexities and considerations to obtaining organic materials that transmit in the long-wave infrared (LWIR) region, because of high optical losses due to the IR absorption of the organic molecules. Our differentiated strategy to extend the frontiers of LWIR transparency is to reduce the IR absorption of the organic moieties. The proposed approach synthesized a sulfur copolymer via the inverse vulcanization of 1,3,5-benzenetrithiol (BTT), which has a relatively simple IR absorption because of its symmetric structure, and elemental sulfur, which is mostly IR inactive. This strategy resulted in approximately 1 mm thick windows with an ultrahigh refractive index (nav > 1.9) and high mid-wave infrared (MWIR) and LWIR transmission, without any significant decline in thermal properties. Furthermore, we demonstrated that our IR transmissive material was sufficiently competitive with widely used optical inorganic and polymeric materials.

Structural Effect of Polyimide Precursors on Highly Thermally Conductive Graphite Films.

In this study, polyimide (PI) with high carbonization yield was used as a precursor to prepare graphite films with high thermal conductivity. The crystallinity, grain size, and thermal conductivity of the graphite films were characterized and found to vary according to the chemical structure of the PI precursor. Aromatic PIs containing ortho-substituted hydroxyl groups in the PI main chain (DHB-BPDA) were synthesized by the polycondensation reaction of 3,3'-dihydroxybenzidine (DHB) and 3,3',4,4'-biphenyltetracarboxylic dianhydride (BPDA). The DHB-BPDA is converted to a polybenzoxazole (PBO) structure through thermolysis reaction during carbonization. The PBO containing a benzene ring and a heterocycle group can provide a strong main chain and high thermal stability due to its resonant structure. The graphite film prepared from DHB-BPDA exhibited a large grain size (63.727 nm) and a high thermal conductivity of 916 W/(mK).

Surface Modification of Sulfur-Assisted Reduced Graphene Oxide with Poly(phenylene sulfide) for Multifunctional Nanocomposites.

The sulfur on the sulfur-assisted reduced graphene oxide (SrGO) surface provides the origin of poly(phenylene sulfide) PPS-grafting via SNAr mechanism. In-situ polymerization from sulfur on SrGO afforded surface modification of SrGO, resulting in enhanced dispersibility in PPS. The tensile strength, electrical and thermal conductivities, and flame retardancy of PPS-coated SrGO were efficiently enhanced using highly concentrated SrGO and masterbatch (MB) for industrial purposes. Three-dimensional X-ray microtomography scanning revealed that diluting MB in the PPS resin afforded finely distributed SrGO across the PPS resin, compared to the aggregated state of graphene oxide. For the samples after dilution, the thermal conductivity and flame retardancy of PPS/SrGO are preserved and typically enhanced by up to 20%. The proposed PPS/SrGO MB shows potential application as an additive for reinforced PPS due to the ease of addition during the extrusion process.

Ultrahigh strength, modulus, and conductivity of graphitic fibers by macromolecular coalescence.

Theoretical considerations suggest that the strength of carbon nanotube (CNT) fibers be exceptional; however, their mechanical performance values are much lower than the theoretical values. To achieve macroscopic fibers with ultrahigh performance, we developed a method to form multidimensional nanostructures by coalescence of individual nanotubes. The highly aligned wet-spun fibers of single- or double-walled nanotube bundles were graphitized to induce nanotube collapse and multi-inner walled structures. These advanced nanostructures formed a network of interconnected, close-packed graphitic domains. Their near-perfect alignment and high longitudinal crystallinity that increased the shear strength between CNTs while retaining notable flexibility. The resulting fibers have an exceptional combination of high tensile strength (6.57 GPa), modulus (629 GPa), thermal conductivity (482 W/m·K), and electrical conductivity (2.2 MS/m), thereby overcoming the limits associated with conventional synthetic fibers.

Tunable Synthesis of Predominant Semi-Ionic and Covalent Fluorine Bonding States on a Graphene Surface.

In this study, fluorinated graphene (FG) was synthesized via a hydrothermal reaction. Graphene oxides (GOs) with different oxygen bonding states and oxygen contents (GO(F), GO(P), and GO(HU)) were used as starting materials. GO(F) and GO(P) are commercial-type GOs from Grapheneall. GO(HU) was prepared using a modified Hummers method. The synthesized FGs from GO(F), GO(P), and GO(HU) are denoted as FG(F), FG(P), and FG(HU), respectively. The F atoms were bound to the graphene surface with predominantly semi-ionic or covalent bonding depending on the GO oxygen state. FG(F) and FG(HU) exhibited less extensive fluorination than FG(P) despite the same or higher oxygen contents compared with that in FG(P). This difference was attributed to the difference in the C=O content of GOs because the C=O bonds in GO primarily produce covalent C-F bonds. Thus, FG(F) and FG(HU) mainly exhibited semi-ionic C-F bonds. The doped F atoms were used to tune the electronic properties and surface chemistry of graphene. The fluorination reaction also improved the extent of reduction of GO.

Fast chemical recycling of carbon fiber reinforced plastic at ambient pressure using an aqueous solvent accelerated by a surfactant.

The properties of infusibility and insolubility in organic solvent of cured epoxy resin makes it difficult to recycle carbon fiber reinforced plastics (CFRP). We have reported the recycling of CFRPs using the oxidizing power of hydroxyl radicals generated from NaOCl solution. In our study, we used benzyltrimethylammonium bromide (BTAB) and sodium dodecyl sulfate (SDS) for the interfacial separation between the epoxy resin and carbon fibers (CF). The surfactant system maximized recycling efficiency in both pretreatment and the main reaction of the CFRP recycling process. In the second step, the reaction time to successfully reclaim the CFs was much shorter, only one hour, compared with the two-hour reaction time for the non-SDS process previously reported by us. Scanning electron microscope images and Raman analyses showed that the surface of the reclaimed CF (r-CFs) was clean and smooth without any defects, and there was no significant structural change compared to virgin CF (v-CFs). The tensile strength of r-CF was 3.42 GPa which is 96.9% of the v-CF. Thus, the CFRP recycling process using SDS not only results in r-CF with good mechanical and physical properties, but also increases recycling efficiency by reducing the time.

Facile in Situ Synthesis of Multiple-Heteroatom-Doped Carbons Derived from Polyimide Precursors for Flexible All-Solid-State Supercapacitors.

Efficient strategies to prepare carbon materials with improved electrochemical performance for supercapacitors have been in great demand. Herein, we develop multiple-heteroatom-doped carbons (from single- to triple-doped) by pyrolysis of polyimide precursors using a facile in situ approach. This approach can be used to tune heteroatom compositions by controlling the desired polyimide monomer functional groups as well as introducing external doping sources into the polyimide precursor solutions. Various types of multiple-heteroatom-doped carbons such as N; N,S-; N,F-; N,S,B-; and N,F,B-doped carbons are synthesized. Among these synthesized multiple-heteroatom-doped carbons, the specific capacitance of N,F,B triple-doped carbon exhibits 350.3 F g-1 at 1 A g-1 in a three-electrode system. Furthermore, a flexible all-solid-state supercapacitor device using the N,F,B-doped carbon with poly(vinyl alcohol)-1 M H2SO4 gel electrolyte demonstrates a volumetric energy density of 0.58 mW h cm-3. It is expected that this synthesis strategy for multiple-heteroatom-doped carbons can be used for practical supercapacitor applications.

Hollow polymer microcapsule embedded transparent and heat-insulating film.

We herein report a facile and scalable approach to manufacturing optically transparent and heat-insulating films by incorporating hollow poly(methyl methacrylate) microcapsules into a transparent polymeric matrix. The microcapsule was prepared via emulsion polymerization. The size of the microcapsules could be easily controlled from ∼1 to 3 µm by varying the polymerization time in a narrow size distribution. The microcapsules were then mixed with a UV-curable transparent liquid resin and cured by a subsequent light irradiation. The current approach could enhance the thermal barrier property of the films without a significant reduction in the optical transparency. The solid film possessing 30 wt% microcapsules, for example, exhibited a high visible light transmittance (∼80% as measured by UV-vis spectroscopy) and the thermal conductivity was reduced to 0.06 W mK-1, corresponding to 46% of the capsule free film. To quantify and verify this result, theoretical models describing a heat transfer in a hollow microsphere composite were used, and the model showed a good agreement with our experimental observations.

Molecular Design and Property Prediction of Sterically Confined Polyimides for Thermally Stable and Transparent Materials.

To meet the demand for next-generation flexible optoelectronic devices, it is crucial to accurately establish the chemical structure-property relationships of new optical polymer films from a theoretical point of view, prior to production. In the current study, computer-aided simulations of newly designed poly(ester imide)s (PEsIs) with various side groups (⁻H, ⁻CH3, and ⁻CF3) and substituted positions were employed to study substituent-derived steric effects on their optical and thermal properties. From calculations of the dihedral angle distribution of the model compounds, it was found that the torsion angle of the C⁻N imide bonds was effectively constrained by the judicious introduction of di-, tetra-, and hexa-substituted aromatic diamines with ⁻CF3 groups. A high degree of fluorination of the PEsI repeating units resulted in weaker intra- and intermolecular conjugations. Their behavior was consistent with the molecular orbital energies obtained using density functional theory (DFT). In addition, various potential energy components of the PEsIs were investigated, and their role in glass-transition behavior was studied. The van der Waals energy (EvdW) played a crucial role in the segmental chain motion, which had an abrupt change near glass-transition temperature (Tg). The more effective steric effect caused by ⁻CF3 substituents at the 3-position of the 4-aminophenyl group significantly improved the chain rigidity, and showed high thermal stability (Tg > 731 K) when compared with the ⁻CH3 substituent at the same position, by highly distorting (89.7°) the conformation of the main chain.

Enhanced Thermal Conductivity of Liquid Crystalline Epoxy Resin using Controlled Linear Polymerization.

A powerful strategy to enhance the thermal conductivity of liquid crystalline epoxy resin (LCER) by simply replacing the conventional amine cross-linker with a cationic initiator was developed. The cationic initiator linearly wove the epoxy groups tethered on the microscopically aligned liquid crystal mesogens, resulting in freezing of the ordered LC microstructures even after curing. Owing to the reduced phonon scattering during heat transport through the ordered LC structure, a dramatic improvement in the thermal conductivity of neat cation-cured LCER was achieved to give a value ∼141% (i.e., 0.48 W/mK) higher than that of the amorphous amine-cured LCER. In addition, at the same composite volume fraction in the presence of a 2-D boron nitride filler, an approximately 130% higher thermal conductivity (maximum ∼23 W/mK at 60 vol %) was observed. The nanoarchitecture effect of the ordered LCER on the thermal conductivity was then examined by a systematic investigation using differential scanning calorimetry, polarized optical microscopy, X-ray diffraction, and thermal conductivity measurements. The linear polymerization of LCER can therefore be considered a practical strategy to enable the cost-efficient mass production of heat-dissipating materials, due to its high efficiency and simple process without the requirement for complex equipment.

Additive-free hollow-structured Co3O4 nanoparticle Li-ion battery: the origins of irreversible capacity loss.

Origins of the irreversible capacity loss were addressed through probing changes in the electronic and structural properties of hollow-structured Co3O4 nanoparticles (NPs) during lithiation and delithiation using electrochemical Co3O4 transistor devices that function as a Co3O4 Li-ion battery. Additive-free Co3O4 NPs were assembled into a Li-ion battery, allowing us to isolate and explore the effects of the Co and Li2O formation/decomposition conversion reactions on the electrical and structural degradation within Co3O4 NP films. NP films ranging between a single monolayer and multilayered film hundreds of nanometers thick prepared with blade-coating and electrophoretic deposition methods, respectively, were embedded in the transistor devices for in situ conduction measurements as a function of battery cycles. During battery operation, the electronic and structural properties of Co3O4 NP films in the bulk, Co3O4/electrolyte, and Co3O4/current collector interfaces were spatially mapped to address the origin of the initial irreversible capacity loss from the first lithiation process. Further, change in carrier injection/extraction between the current collector and the Co3O4 NPs was explored using a modified electrochemical transistor device with multiple voltage probes along the electrical channel.

Simultaneous study of exciton diffusion/dissociation and charge transport in a donor-acceptor bilayer: pentacene on a C60 -terminated self-assembled monolayer.

In-situ photoinduced threshold voltage measurement is a sensitive probe for exploring charge transport and exciton diffusion simultaneously, the main determinants of the power conversion efficiency in organic photovoltaic devices. The exciton diffusion length in a pentacene film deposited onto a C60 -terminated self-assembled monolayer is measured. The methodology and analysis presented here can be applied in the design and engineering of electron/donor acceptor interfaces for photovoltaic devices..

Chemical method for improving both the electrical conductivity and mechanical properties of carbon nanotube yarn via intramolecular cross-dehydrogenative coupling.

Chemical post-treatment of the carbon nanotube fiber (CNTF) was carried out via intramolecular cross-dehydrogenative coupling (ICDC) with FeCl3 at room temperature. The Raman intensity ratio of the G band to the D band (IG/ID ratio) of CNT fiber increased from 2.3 to 4.6 after ICDC reaction. From the XPS measurements, the AC═C/AC-C ratio of the CNT fiber increased from 3.6 to 4.8. It is of keen interest that both the electrical conductivity and tensile strength of CNT yarn improved to 3.5 × 10(3) S/cm and 420 MPa, which is 180 and 200% higher than that of neat CNT yarn.