A review of struvite crystallization for nutrient source recovery from wastewater.

Nutrient recovery from wastewater not only reduces the nutrient load on water resources but also alleviates the environmental problems in aquatic ecosystems, which is a solution to achieve a sustainable society. Besides, struvite crystallization technology is considered a potential nutrient recovery technology because the precipitate obtained can be reused as a slow-release fertilizer. This review presents the basic properties of struvite and the theory of the basic crystallization process. In addition, the possible influencing variables of the struvite crystallization process on the recovery efficiency and product purity are also examined in detail. Then, the advanced auxiliary technologies for facilitating the struvite crystallization process are systematically discussed. Moreover, the economic and environmental benefits of the struvite crystallization process for nutrient recovery are introduced. Finally, the shortcomings and inadequacies of struvite crystallization technology are presented, and future research prospects are provided. This work serves as the foundation for the future use of struvite crystallization technology to recover nutrients in response to the increasingly serious environmental problems and resource depletion.

Bidirectional planar-displacement waveguide tracker for high-concentration photovoltaics.

A bidirectional planar-displacement waveguide tracker was devised to replace the traditional two-axis tracking system for high-concentration photovoltaics, with improved module thickness, optical field uniformity, and current matching. The concentrating magnification reaches 725 times, and the sun tracking angle is more than 170°, which is equivalent to 11.3 tracking hours per day. The module thickness is only 6.16 cm. This design enabled us to place the module flat on the ground, in which swing was not required. This will greatly improve the mechanical strength and the lifetime of the module and solve the development dilemma faced by III-V multijunction solar cells.

Ultrasonic power combined with seed materials for recovery of phosphorus from swine wastewater via struvite crystallization process.

Recovering P via struvite crystallization is an effective way to utilize the resources in swine wastewater. At present, the main challenges of traditional struvite crystallization process are the long reaction time and insufficient removal efficiency. In this study, a novel method to promote struvite crystallization process through ultrasound (US) combined with seed materials is proposed to overcome these defects. We systematically study the effects of US, seed materials, and ultrasonic power on nutrient recovery. The experimental results show that under the conditions of pH 9.5 and MgCl2:P molar ratio1.4:1, the addition of 2 g/L pre-synthesized struvite as the seed materials can increase the P removal rate to 91.56%, whereas, the addition of 80 W ultrasonic power for 15 min can make the P removal rate reach 94.18%. Meanwhile, the combination of US and struvite seed crystals can achieve a maximum P removal efficiency value of 97.66% in which 10 min for the reaction time is enough. The products are characterized using XRD, SEM, and FTIR to determine the phosphorus removal mechanism of ultrasonic power combined with seed induction. The shearing effect of US is found beneficial to affect the surface morphology of the seed crystals, which provides more nucleation sites to enhance crystal nucleation and growth. The removal efficiency comparison reveals that this combined technology performs an excellent removal effect.

Proteomics Analysis of Candida albicans dnm1 Haploid Mutant Unraveled the Association between Mitochondrial Fission and Antifungal Susceptibility.

Candida albicans is a major fungal pathogen, accounting for approximately 15% of healthcare infections with associated mortality as high as 40% in the case of systemic candidiasis. Antifungal agents for C. albicans infections are limited, and rising resistance is an inevitable problem. Therefore, understanding the mechanism behind antifungal responses is among the top research focuses in combating Candida infections. Herein, the recently developed C. albicans haploid model is employed to examine the association between mitochondrial fission, regulated by Dnm1, and the pathogen's response to antifungals. Proteomic analysis of dnm1Δ and its wild-type haploid parent, GZY803, reveal changes in proteins associated with mitochondrial structures and functions, cell wall, and plasma membrane. Antifungal susceptibility testing revealed that dnm1Δ is more susceptible to SM21, a novel antifungal, than GZY803. Analyses of reactive oxygen species release, antioxidant response, lipid peroxidation, and membrane damages uncover an association between dnm1Δ and the susceptibility to SM21. Dynasore-induced mitochondrial inhibition in SC5314 diploids corroborate the findings. Interestingly, Dynasore-primed SC5314 cultures exhibit increased susceptibility to all antifungals tested. These data suggest an important contribution of mitochondrial fission in antifungal susceptibility of C. albicans. Hence, mitochondrial fission can be a potential target for combined therapy in anti-C. albicans treatment.

G1 and S phase arrest in Candida albicans induces filamentous growth via distinct mechanisms.

Candida albicans is an opportunistic fungal pathogen. In immunocompromised individuals, it can cause bloodstream infections with high mortality rates. The ability to switch between yeast and hyphal morphologies is a critical virulence factor of C. albicans. In response to diverse environmental cues, several signaling pathways are activated resulting in filamentous growth. Interestingly, cell cycle arrest can also trigger filamentous growth although the pathways involved are not well-understood. Here, we demonstrate that the cAMP-PKA pathway is involved in the filamentous growth caused by G1 arrest due to the depletion of the G1 cyclin Cln3 and S phase arrest due to hydroxyurea treatment. The downstream mechanisms involved in filamentation are different between the two cell cycle arrest phenomena. Cln3-depleted cells require HGC1 and UME6 for filamentous growth, but hydroxyurea-induced filamentation does not. Also, the hyphal repressor Nrg1 is not involved in the suppression of Cln3-depletion and hydroxyurea-induced filamentous growth. The findings highlight the complexity of the signaling networks that control filamentous growth in which different mechanisms downstream of the cAMP-PKA pathway are activated based on the nature of the inducing signals.

The 'obligate diploid' Candida albicans forms mating-competent haploids.

Candida albicans, the most prevalent human fungal pathogen, is considered to be an obligate diploid that carries recessive lethal mutations throughout the genome. Here we demonstrate that C. albicans has a viable haploid state that can be derived from diploid cells under in vitro and in vivo conditions, and that seems to arise through a concerted chromosome loss mechanism. Haploids undergo morphogenetic changes like those of diploids, including the yeast-hyphal transition, chlamydospore formation and a white-opaque switch that facilitates mating. Haploid opaque cells of opposite mating type mate efficiently to regenerate the diploid form, restoring heterozygosity and fitness. Homozygous diploids arise spontaneously by auto-diploidization, and both haploids and auto-diploids show a similar reduction in fitness, in vitro and in vivo, relative to heterozygous diploids, indicating that homozygous cell types are transient in mixed populations. Finally, we constructed stable haploid strains with multiple auxotrophies that will facilitate molecular and genetic analyses of this important pathogen.

Candida albicans possess a highly versatile and dynamic high-affinity iron transport system important for its commensal-pathogenic lifestyle.

Iron is an essential nutrient for nearly all organisms, but iron overdose is toxic. The human commensal-pathogenic fungus Candida albicans traverses host niches with markedly different iron availability. During systemic infection, C. albicans must activate the high-affinity iron permease Ftr1 to acquire iron sequestered by the host's iron-withholding defense and suppresses iron uptake while residing in the iron-rich gut to avoid toxicity. Ftr1 associates with a ferroxidase to form an iron transporter. C. albicans contains four permeases and five ferroxidase homologs, suggesting 20 possible subunit combinations. Here, we investigated the iron-dependent expression, cellular localization and interacting partners of all permeases and ferroxidases and the significance of each subunit for gastrointestinal colonization and systemic infection in mice. We uncovered three distinct patterns of iron-dependent expression and highly flexible ferroxidase-permease partnerships, which underlie a dynamic iron transport system that can be deftly tuned according to iron availability. We found functional differentiation as well as redundancy among the ferroxidases and permeases during both gastrointestinal colonization and bloodstream infection. We propose that C. albicans possesses a sophisticated iron acquisition and utilization system befitting its commensal-pathogenic lifestyle. Our findings reveal new possibilities for medical intervention of C. albicans infection.

Comparative Ploidy Proteomics of Candida albicans Biofilms Unraveled the Role of the AHP1 Gene in the Biofilm Persistence Against Amphotericin B.

Candida albicans is a major fungal pathogen causing lethal infections in immunocompromised patients. C. albicans forms antifungal tolerant biofilms contributing significantly to therapeutic failure. The recently established haploid C. albicans biofilm model provides a new toolbox to uncover the mechanism governing the higher antifungal tolerance of biofilms. Here, we comprehensively examined the proteomics and antifungal susceptibility of standard diploid (SC5314 and BWP17) and stable haploid (GZY792 and GZY803) strains of C. albicans biofilms. Subsequent downstream analyses identified alkyl hydroperoxide reductase 1 (AHP1) as a critical determinant of C. albicans biofilm's tolerance of amphotericin B. At 32 µg/ml of amphotericin B, GZY803 haploid biofilms showed 0.1% of persister population as compared with 1% of the diploid biofilms. AHP1 expression was found to be lower in GZY803 biofilms, and AHP1 overexpression in GZY803 restored the percentage of persister population. Consistently, deleting AHP1 in the diploid strain BWP17 caused a similar increase in amphotericin B susceptibility. AHP1 expression was also positively correlated with the antioxidant potential. Furthermore, C. albicans ira2Δ/Δ biofilms were susceptible to amphotericin B and had a diminished antioxidant capacity. Interestingly, AHP1 overexpression in the ira2Δ/Δ strain restored the antioxidant potential and enhanced the persister population against amphotericin B, and shutting down the AHP1 expression in ira2Δ/Δ biofilms reversed the effect. In conclusion, we provide evidence that the AHP1 gene critically determines the amphotericin B tolerance of C. albicans biofilms possibly by maintaining the persisters' antioxidant capacity. This finding will open up new avenues for developing therapies targeting the persister population of C. albicans biofilms. The mass spectrometry proteomics data are available via ProteomeXchange with identifier PXD004274.

Tpd3-Pph21 phosphatase plays a direct role in Sep7 dephosphorylation in Candida albicans.

Septins are a component of the cytoskeleton and play important roles in diverse cellular processes including cell cycle control, cytokinesis and polarized growth. In fungi, septin organization, dynamics and function are regulated by phosphorylation, and several kinases responsible for the phosphorylation of several septins have been identified. However, little is known about the phosphatases that dephosphorylate septins. Here, we report the characterization of Tpd3, a structural subunit of the PP2A family of phosphatases, in the pathogenic fungus Candida albicans. We found that tpd3Δ/Δ cells are defective in hyphal growth and grow as pseudohyphae under yeast growth conditions with aberrant septin organization. Western blotting detected hyperphosphorylation of the septin Sep7 in cells lacking Tpd3. Tpd3 and Sep7 colocalize at the bud neck and can coimmunoprecipitate. Furthermore, we discovered similar defects in cells lacking Pph21, a catalytic subunit of the PP2A family, and its physical association with Tpd3. Importantly, purified Tpd3-Pph21 complexes can dephosphorylate Sep7 in vitro. Together, our findings strongly support the idea that the Tpd3-Pph21 complex dephosphorylates Sep7 and regulates morphogenesis and cytokinesis. The tpd3Δ/Δ mutant is greatly reduced in virulence in mice, providing a potential antifungal target.

CDK phosphorylates the polarisome scaffold Spa2 to maintain its localization at the site of cell growth.

Polarisome is a protein complex that plays an important role in polarized growth in fungi by assembling actin cables towards the site of cell growth. For proper morphogenesis, the polarisome must localize to the right place at the right time. However, the mechanisms that control polarisome localization remain poorly understood. In this study, using the polymorphic fungus Candida albicans as a model, we have discovered that the cyclin-dependent kinase (CDK) Cdc28 phosphorylates the polarisome scaffold protein Spa2 to govern polarisome localization during both yeast and hyphal growth. In a yeast cell cycle, Cdc28-Clb2 phosphorylates Spa2 and controls the timing of polarisome translocation from the bud tip to the bud neck. And during hyphal development, Cdc28-Clb2 and the hyphal-specific Cdc28-Hgc1 cooperate to enhance Spa2 phosphorylation to maintain the polarisome at the hyphal tip. Blocking the CDK phosphorylation causes premature tip-to-neck translocation of Spa2 during yeast growth and inappropriate septal localization of Spa2 in hyphae and abnormal hyphal morphology under certain inducing conditions. Together, our results generate new insights into the mechanisms by which fungi regulate polarisome localization in the control of polarized growth.

Enhancement of Fenton oxidation for removing organic matter from hypersaline solution by accelerating ferric system with hydroxylamine hydrochloride and benzoquinone.

Fenton oxidation is generally inhibited in the presence of a high concentration of chloride ions. This study investigated the feasibility of using benzoquinone (BQ) and hydroxylamine hydrochloride (HA) as Fenton enhancers for the removal of glycerin from saline water under ambient temperature by accelerating the ferric system. It was found that organics removal was not obviously affected by chloride ions of low concentration (less than 0.1mol/L), while the mineralization rate was strongly inhibited in the presence of a large amount of chloride ions. In addition, ferric hydrolysis-precipitation was significantly alleviated in the presence of HA and BQ, and HA was more effective in reducing ferric ions into ferrous ions than HA, while the H2O2 decomposition rate was higher in the BQ-Fenton system. Electron spin resonance analysis revealed that OH production was reduced in high salinity conditions, while it was enhanced after the addition of HA and BQ (especially HA). This study provided a possible solution to control and alleviate the inhibitory effect of chloride ions on the Fenton process for organics removal.

Regulation of Rfa2 phosphorylation in response to genotoxic stress in Candida albicans.

Successful pathogens must be able to swiftly respond to and repair DNA damages inflicted by the host defence. The replication protein A (RPA) complex plays multiple roles in DNA damage response and is regulated by phosphorylation. However, the regulators of RPA phosphorylation remain unclear. Here, we investigated Rfa2 phosphorylation in the pathogenic fungus Candida albicans. Rfa2, a RFA subunit, is phosphorylated when DNA replication is inhibited by hydroxyurea and dephosphorylated during the recovery. By screening a phosphatase mutant library, we found that Pph3 associates with different regulatory subunits to differentially control Rfa2 dephosphorylation in stressed and unstressed cells. Site-directed mutagenesis revealed T11, S18, S29, and S30 being critical for Rfa2 phosphorylation in response to genotoxic insult. We obtained evidence that the genome integrity checkpoint kinase Mec1 and the cyclin-dependent kinase Clb2-Cdc28 mediate Rfa2 phosphorylation. Although cells expressing either a phosphomimetic or a non-phosphorylatable version of Rfa2 had defects, the latter exhibited greater sensitivity to genotoxic challenge, failure to repair DNA damages and to deactivate Rad53-mediated checkpoint pathways in a dosage-dependent manner. These mutants were also less virulent in mice. Our results provide important new insights into the regulatory mechanism and biological significance of Rfa2 phosphorylation in C. albicans.

Type I photodynamic antimicrobial therapy: Principles, progress, and future perspectives.

The emergence of drug-resistant bacteria has significantly diminished the efficacy of existing antibiotics in the treatment of bacterial infections. Consequently, the need for finding a strategy capable of effectively combating bacterial infections has become increasingly urgent. Photodynamic therapy (PDT) is considered one of the most promising emerging antibacterial strategies due to its non-invasiveness, low adverse effect, and the fact that it does not lead to the development of drug resistance. However, bacteria at the infection sites often exist in the form of biofilm instead of the planktonic form, resulting in a hypoxic microenvironment. This phenomenon compromises the treatment outcome of oxygen-dependent type-II PDT. Compared to type-II PDT, type-I PDT is not constrained by the oxygen concentration in the infected tissues. Therefore, in the treatment of bacterial infections, type-I PDT exhibits significant advantages over type-II PDT. In this review, we first introduce the fundamental principles of type-I PDT in details, including its physicochemical properties and how it generates reactive oxygen species (ROS). Next, we explore several specific antimicrobial mechanisms utilized by type-I PDT and summarize the recent applications of type-I PDT in antimicrobial treatment. Finally, the limitations and future development directions of type-I photosensitizers are discussed. STATEMENT OF SIGNIFICANCE: The misuse and overuse of antibiotics have accelerated the development of bacterial resistance. To achieve the effective eradication of resistant bacteria, pathfinders have devised various treatment strategies. Among these strategies, type I photodynamic therapy has garnered considerable attention owing to its non-oxygen dependence. The utilization of non-oxygen-dependent photodynamic therapy not only enables the effective elimination of drug-resistant bacteria but also facilitates the successful eradication of hypoxic biofilms, which exhibits promising prospects for treating biofilm-associated infections. Based on the current research status, we anticipate that the novel type I photodynamic therapy agent can surmount the biofilm barrier, enabling efficient treatment of hypoxic biofilm infections.

Nanotechnology-driven strategies to enhance the treatment of drug-resistant bacterial infections.

The misuse of antibiotics has led to increased bacterial resistance, posing a global public health crisis and seriously endangering lives. Currently, antibiotic therapy remains the most common approach for treating bacterial infections, but its effectiveness against multidrug-resistant bacteria is diminishing due to the slow development of new antibiotics and the increase of bacterial drug resistance. Consequently, developing new a\ntimicrobial strategies and improving antibiotic efficacy to combat bacterial infection has become an urgent priority. The emergence of nanotechnology has revolutionized the traditional antibiotic treatment, presenting new opportunities for refractory bacterial infection. Here we comprehensively review the research progress in nanotechnology-based antimicrobial drug delivery and highlight diverse platforms designed to target different bacterial resistance mechanisms. We also outline the use of nanotechnology in combining antibiotic therapy with other therapeutic modalities to enhance the therapeutic effectiveness of drug-resistant bacterial infections. These innovative therapeutic strategies have the potential to enhance bacterial susceptibility and overcome bacterial resistance. Finally, the challenges and prospects for the application of nanomaterial-based antimicrobial strategies in combating bacterial resistance are discussed. This article is categorized under: Biology-Inspired Nanomaterials > Nucleic Acid-Based Structures Therapeutic Approaches and Drug Discovery > Nanomedicine for Infectious Disease.

Facile one-step synthesis of inorganic-framework molecularly imprinted TiO2/WO3 nanocomposite and its molecular recognitive photocatalytic degradation of target contaminant.

Inorganic-framework molecularly imprinted TiO2/WO3 nanocomposites with molecular recognitive photocatalytic activity were first prepared successfully by a facile one-step sol-gel method using 2-nitrophenol and 4-nitrophenol as template molecules, and tetrabutyl orthotitanate as titanium source as well as the precursor of functional monomer which could complex with template molecules. The template molecules could be completely removed by means of high-temperature calcination, avoiding the traditional extraction procedures that are time- as well as solvent-consuming. Compared to nonimprinted TiO2/WO3, the molecularly imprinted TiO2/WO3 shows a much higher adsorption capacity and selectivity toward the template molecules. The enhancement in terms of adsorption capacity and selectivity can be attributed to the chemical interaction between target molecules and imprinted cavities, as well as size matching between imprinted cavities and target molecules. The photocatalytic activity of molecularly imprinted TiO2/WO3 toward the target molecules is more than two times that of non-imprinted TiO2/WO3, a result of selective adsorption of target molecules on molecularly imprinted TiO2/WO3. The formation pathway of intermediate products in 2-nitrophenol and 4-nitrophenol degradation process was provided. Moreover, molecularly imprinted TiO2/WO3 exhibits high stability. The results indicate that inorganic-framework molecularly imprinted TiO2/WO3 nanocomposites have a promising prospect in the treatment of wastewater for irrigation.

Direct removal of aqueous As(III) and As(V) by amorphous titanium dioxide nanotube arrays.

Amorphous titanium dioxide nanotube arrays (TiO2 NTs) were prepared by a simple anodization process without subsequent calcination at high temperature, and the effectiveness of amorphous TiO2 NTs as adsorbents in removing arsenite (As(III)) and arsenate (As(V)) was investigated. The TiO2 NTs were not only effective for arsenic removal without a pre-oxidation of As(III) to As(V) and/or adjusting the pH value of water before the adsorption process, but also can be separated and recovered easily from the solution. The adsorption kinetics and adsorption capacity of the amorphous TiO2 NTs for As(III) and As(V) were studied separately by batch experiments. The apparent values for Langmuir monolayer sorption capacities were 28.9 mg/g for As(III) and 24.7 mg/g for As(V) at pH 7. Kinetics studies indicated that the adsorption process on TiO2 NTs followed a pseudo-second-order kinetics model. Arsenic adsorption of TiO2 NTs remains stable over a broad pH range. Moreover, the TiO2 NTs have excellent stability and regeneration, and they can be used repeatedly at least five times.

Process parameters and biological mechanism of efficient removal of Cd(II) ion from wastewater by a novel Bacillus subtilis TR1.

The safe treatment of heavy metals in wastewater is directly related to the human health and social development. In this paper, a new biological strain has been isolated from electroplating wastewater, which can effectively remove metal ions in wastewater. The results of 16 S rDNA sequencing analysis and NCBI GenBank database comparison show that the strain belongs to a novel Bacillus genus and names Bacillus subtilis TR1 with the accession number of OL441606. The removal rate of Cd(II) reaches to 85.68% with the conditions of pH = 7, C0Cd(II) = 20 mg L-1, t = 48 h, m = 0.1 g, and T = 35 °C. The biological removal mechanism of Cd(II) is in-depth studied by FTIR and XRD combined with third-generation sequencing. The results indicate that Bacillus subtilis TR1 removes Cd(II) mainly through two synergistic pathways, namely, extracellular chemisorption and intracellular bioaccumulation: 1) The groups carried on the surface of the strain, such as -COOH, -NH, -OH and C-H, have good chemisorption properties for Cd(II) and easily form cadmium containing chelation (-COO-Cd(II), -N-Cd(II), etc.) with these groups. The appearance of TR1 strain changes from cylindrical to spherical after Cd(II) adsorption, which is due to the biotoxicity of Cd(II); 2) Cd(II) exchanges on the surface of TR1 strain with K and Na ions released from the intracellular cytoplasm and enters the cytoplasm under the transfer of biological transport medium. This part of Cd(II) is converted into its own components by anabolic enzymes and accumulates in the cytoplasm. These data provide a new biological agent for the efficient treatment of heavy metal ions in wastewater and enrich relevant theoretical knowledge.

Cytochrome c regulates hyphal morphogenesis by interfering with cAMP-PKA signaling in Candida albicans.

In the human fungal pathogen Candida albicans, invasive hyphal growth is a well-recognized virulence trait. We employed transposon-mediated genome-wide mutagenesis, revealing that inactivating CTM1 blocks hyphal growth. CTM1 encodes a lysine (K) methyltransferase, which trimethylates cytochrome c (Cyc1) at K79. Mutants lacking CTM1 or expressing cyc1K79A grow as yeast under hyphae-inducing conditions, indicating that unmethylated Cyc1 suppresses hyphal growth. Transcriptomic analyses detected increased levels of the hyphal repressor NRG1 and decreased levels of hyphae-specific genes in ctm1Δ/Δ and cyc1K79A mutants, suggesting cyclic AMP (cAMP)-protein kinase A (PKA) signaling suppression. Co-immunoprecipitation and in vitro kinase assays demonstrated that unmethylated Cyc1 inhibits PKA kinase activity. Surprisingly, hyphae-defective ctm1Δ/Δ and cyc1K79A mutants remain virulent in mice due to accelerated proliferation. Our results unveil a critical role for cytochrome c in maintaining the virulence of C. albicans by orchestrating proliferation, growth mode, and metabolism. Importantly, this study identifies a biological function for lysine methylation on cytochrome c.

Effects of incineration and pyrolysis on removal of organics and liberation of cathode active materials derived from spent ternary lithium-ion batteries.

Removing organics via thermal treatment to liberate active materials from spent cathode sheets is essential for recovering lithium-ion batteries. In this study, the effects of incineration, N2 pyrolysis, and CO2 pyrolysis on the removal of organics and liberation of ternary cathode active materials (CAMs) were compared. The results indicated that the organics in the spent ternary cathode sheets comprised a residual electrolyte and polyvinylidene fluoride (PVDF) binder. Moreover, the organics could be removed to promote the liberation of CAMs via incineration, N2 pyrolysis, and CO2 pyrolysis. When the temperature was <200 °C, the chemical properties of the volatilized ester electrolyte remained unchanged during both N2 and CO2 pyrolysis, indicating that the electrolyte can be collected by controlling the pyrolysis temperature and condensation. Furthermore, PVDF binder decomposition occurred at 200-600 °C. The optimal temperatures of incineration, N2 pyrolysis, and CO2 pyrolysis were 550, 500, and 450 °C, respectively, and these treatments increased the liberation efficiency of CAMs from 81.49 % to 98.75 %, 99.26 %, and 97.98 %, respectively. In addition, heat-treated CAMs required less time to achieve adequate liberation. Following three thermal treatment processes, the sizes of the CAM particles were mainly concentrated in the ranges of 0.075-0.1 mm and <0.075 mm. Furthermore, for all types of CAMs examined, the Al concentration decreased from 1.09 % to <0.35 %, which increased the separation efficiency and improved the chemical metallurgical performance.