Wide Restorative Emergence Angle Increases Marginal Bone Loss and Impairs Integrity of the Junctional Epithelium of the Implant Supracrestal Complex: A Preclinical Study.

AIM: To assess the influence of the emergence angle on marginal bone loss (MBL) and supracrestal soft tissue around dental implants. MATERIALS AND METHODS: In six mongrel dogs, the mandibular premolars and molars were extracted. After 3 months of healing, four dental implants were placed in each hemimandible. The implants were randomly allocated to receive one of four customized healing abutments, each with a different value of the restorative emergence angle: 20°, 40°, 60° or 80°. Intra-oral radiographs were taken after placing the healing abutments and at 6, 9, 16 and 24 weeks of follow-up. Then, micro-CT and undecalcified histology and synchrotron were performed. MBL over time was analysed with generalized estimating equations (GEEs) and adjusted for baseline soft-tissue thickness. RESULTS: From implant placement to 24 weeks, GEE modelling showed that the MBL at mesial and distal sites consistently increased over time, indicating MBL in all groups (p < 0.001). The model indicated that MBL varied significantly across the different restorative angles (angle effect, p < 0.001), with 80° showing the greatest bone loss. Micro-CT, histology and synchrotron confirmed the corresponding trends and showed that wide restorative angles (60° and 80°) impaired the integrity of the junctional epithelium of the supracrestal tissue. CONCLUSIONS: A wide restorative angle increases MBL and impairs the integrity of the junctional epithelium of the implant supracrestal complex.

Mechanical performance of patient-specific prefabricated temporary shell versus laboratory-fabricated CAD/CAM provisional implant-supported single-tooth restorations: A laboratory study.

OBJECTIVE: To evaluate the mechanical performance of patient-specific prefabricated temporary shell versus laboratory-fabricated CAD/CAM provisional restorations on titanium temporary abutments, with and without thermo-mechanical ageing. MATERIALS AND METHODS: Implants with a conical connection were divided into four groups (n = 24) and restored with temporary shell or laboratory-fabricated central or lateral incisor PMMA restorations that were relined or bonded on titanium temporary abutments. The diameter of the central and lateral incisor groups' implants was regular (ϕ 4.3 mm) or narrow (ϕ 3.5 mm), respectively. Half of each group's specimens were subjected to ageing, simultaneous thermocycling (5-55°C) and chewing simulation (120,000 cycles, 50 N, 1.7 Hz) resulting in eight groups in total (n = 12). The aged specimens were evaluated with optical microscopy, and survival and complication rates were determined according to modified USPHS criteria. The non-aged specimens and those that had survived ageing were loaded until failure, whereupon bending moments were calculated. RESULTS: Survival rates after ageing were 100% for all groups. Apart from wear facets (ϕ 2-3 mm) on the palatal restoration surface, no complications were observed. The mean fracture load and bending moments ranged between 597.6-847.1 N and 433.3-550.6 Ncm, respectively, with no significant differences between the eight groups (p = .25; p = .20). CONCLUSIONS: As patient-specific temporary shell central and lateral incisor provisional implant-supported restorations are mechanically stable enough to withstand clinical bite forces, even after thermo-mechanical ageing, they may serve as an alternative to laboratory-fabricated provisional restorations.

A 3D micro-CT assessment of composition and structure of bone tissue after vertical and horizontal alveolar ridge augmentation using CAD/CAM-customized titanium mesh.

OBJECTIVES: To date, no studies have exploited micro-CT in humans to evaluate bone morphology and structure after bone augmentation with CAD/CAM-customized titanium mesh, in mandible and maxilla. The aim of this study was to assess the composition and microstructure of bone biopsy through micro-CT analysis. MATERIALS AND METHODS: Bone augmentation at both maxillary and mandible sites was performed on 30 patients randomly treated with customized mesh, either alone (M-) or covered with resorbable membrane (M+), in both cases filled 50:50 with autogenous bone and xenograft. After 6 months, biopsies were taken and micro-CT was performed on consecutive 1-mm-thick VOIs from coronal to apical side, measuring tissue volumes, trabecular thickness, spacing, and number. RESULTS: In both groups, irrespective of membrane use, bone tissue (M-: 29.76% vs. M+: 30.84%) and residual graft material (M-: 14.87% vs. M+: 13.11%) values were similar. Differences were site-related (maxillary vs. mandibular) with higher percentage of bone tissue and trabecular density of low-mineralized bone and overall bone in the mandible. CONCLUSIONS: The composition and structure of bone tissue, as assessed by micro-CT after alveolar ridge augmentation using CAD/CAM-customized titanium meshes, showed similar features regardless of whether a collagen membrane was applied.

Marginal changes at bone-level implants supporting dental prostheses with or without intermediate standardised abutments after 36 months: Randomised controlled clinical trial.

OBJECTIVE: The objective of this study is to evaluate the changes at marginal bone level at implants restored with screw-retained prosthesis connected directly to the implants or with an intermediate abutment, after 3-year follow-up. MATERIAL AND METHODS: Thirty-six partially edentulous patients received 72 implants. Each patient received 2 implants and a 2-4-unit screw-retained implant-prosthesis. The test group implants received a screw-retained prosthesis connected directly to the implant shoulder, the control group prosthesis were connected through a 3-mm standardised intermediate abutment. Clinical and radiological data were recorded at baseline and at 6-, 12-, and 36-month follow-up. RESULTS: At 36 months, the mean marginal bone loss was 0.13 ± 0.18 mm for the control group and 0.20 ± 0.24 for the test group, with no significant differences between groups (p > .05). Clinical variables (Probing Pocket Depth, Bleeding on Probing and Plaque Index) at 36 months also showed no significant difference between groups. Minor complications frequency was 6.7% in the control group and 5.3% in test group. None of the groups suffered from mayor complications. Patient Reported Outcomes (PROs) showed a General Satisfaction mean score in the control group of 9.40 (SD 0.82) and 9.37 (SD 1.06) in the test group with no significant differences between groups. CONCLUSIONS: Bone-level implants restored with screw-retained partial prostheses with or without intermediate abutments showed similar radiographic and clinical outcomes after 3 years.

In vitro assessment of cementation of CAD/CAM fabricated prostheses over titanium bases. A systematic review.

OBJECTIVES: The objective of this study is to investigate the outcomes of clinically relevant laboratory studies regarding the cementation of implant-supported restorations over ti-bases. MATERIALS AND METHODS: The present study has been conducted according to PRISMA statement. An electronic search was performed, including publications up to March 2024, to identify studies investigating the parameters affecting the cementation between ti-bases and CAD/CAM prostheses. An assessment of the internal validity was performed, using a custom-made risk of bias tool (QUIN). RESULTS: From the included studies, 40.1% were reported on luting systems, 25% on ti-base surface treatment, 25% on restoration surface, 21.8% on restoration material, and 18.7% on ti-base height. The majority of the included studies were associated with a medium risk of bias. In the absence of micro-retentive features, air-abrasion of ti-bases with a minimum height of 3.5 mm can be beneficial for restoration's retention. The bonding performance can vary not only between different bonding systems but also for different applications within the same system, based on a restoration's material and surface treatment as well as on ti-base height and surface treatment. CONCLUSIONS: The height of the ti-base seems to be the prevailing factor as it constitutes the prerequisite for other modifications of the bonding surfaces to have an advantageous effect. Since the parameters that can affect bonding performance between ti-base and restoration can interact with each other, it is important for the clinician to focus on verified bonding protocols.

Influence of sterilization on the retention forces of lithium disilicate and polymer-infiltrated ceramic-network crowns bonded to titanium base abutments: An in-vitro study.

OBJECTIVES: The aim of this study was to evaluate the effect of sterilization on the retention forces of lithium disilicate (LD) and polymer-infiltrated ceramic network (PICN) crowns bonded to titanium base (Ti-base) abutments. MATERIALS AND METHODS: Forty LD and 40 PICN crowns were milled and then bonded to 80 Ti-bases with two resin composite cements: Multilink Hybrid Abutment (mh) and Panavia V5 (pv) for a total of 8 groups (n = 10). Half of the specimens (test) underwent an autoclaving protocol (pressure 1.1 bar, 121°C, 20.5 min) and the other half not (control). Restorations were screw-retained to implants, and retention forces (N) were measured with a pull-off testing machine. The surfaces of the Ti-bases and the crowns were inspected for the analysis of the integrity of the marginal bonding interface and failure mode. Student's t-test, chi-square test, and univariate linear regression model were performed to analyze the data (α = 0.05). RESULTS: The mean pull-off retention forces ranged from 487.7 ± 73.4 N to 742.2 ± 150.3 N. Sterilized groups showed statistically significant overall higher maximum retention forces (p < .05), except for one combination (LD + mh). Sterilization led to an increased presence of marginal gaps and deformities compared to no-sterilization (p < .001), while no statistically significant relationship was found between failure mode and sterilization (p > .05). CONCLUSIONS: Sterilization may have a beneficial effect on the retention forces of LD and PICN crowns bonded to titanium base abutments, although it may negatively influence the integrity of the marginal bonding interface.

Material and abutment selection for CAD/CAM implant-supported fixed dental prostheses in partially edentulous patients - A narrative review.

Restorative material selection has become increasingly challenging due to the speed of new developments in the field of dental material science. The present narrative review gives an overview of the current indications for implant abutments and restoration materials for provisional and definitive implant-supported fixed dental prostheses in partially edentulous patients. For single implant restorations, titanium base abutments for crowns are suggested as an alternative to the conventional stock- and customized abutments made out of metal or zirconia. They combine the mechanical stability of a metallic connection with the esthetic potential of ceramics. For multiple-unit restorations, conical titanium bases especially designed for bridges are recommended, to compensate for deviating implant insertion axes and angulations. Even though titanium base abutments with different geometries and heights are available, certain clinical scenarios still benefit from customized titanium abutments. Indications for the definitive material in fixed implant restorations depend on the region of tooth replacement. In the posterior (not esthetically critical) zone, ceramics such as zirconia (3-5-Ymol%) and lithium-disilicate are recommended to be used in a monolithic fashion. In the anterior sector, ceramic restorations may be buccally micro-veneered for an optimal esthetic appearance. Lithium-disilicate is only recommended for single-crowns, while zirconia (3-5-Ymol%) is also recommended for multiple-unit and cantilever restorations. Attention must be given to the specific mechanical properties of different types of zirconia, as some feature reduced mechanical strengths and are therefore not indicated for all regions and restoration span lengths. Metal-ceramics remain an option, especially for cantilever restorations.

Histological and histomorphometric analysis of bone tissue using customized titanium meshes with or without resorbable membranes: A randomized clinical trial.

OBJECTIVES: To date, no clinical studies have investigated the effect of using resorbable collagen membrane in conjunction with customized titanium mesh to promote bone formation in guided bone regeneration. Therefore, a non-inferiority analysis (one-sided 95% CI approach) was designed to compare the augmented bone gained using meshes with and without collagen membranes, through histological and histomorphometric investigations. MATERIALS AND METHODS: Thirty patients undergoing bone augmentation procedures at both maxillary and mandible sites were randomly treated with customized titanium meshes alone (M-, n = 15) or covered with resorbable membrane (M+, n = 15), in both cases filled with autogenous bone and xenograft. After 6 months of healing, bone tissue biopsies were taken from the augmented region. The bone tissue (B.Ar), grafting material (G.Ar), and non-mineralized tissue (NMT.Ar) areas were quantified through histomorphometric analysis, as were the osteoid area (O.Ar) and its width. RESULTS: Collagen membrane did not appear to significantly influence the investigated parameters: B.Ar, G.Ar, NMT.Ar, and O.Ar were similar between Group M- (34.3%, 11.5%, 54.1%, 1.95 µm2 , respectively) and Group M+ (35.3%, 14.6%, 50.2%, and 1.75 µm2 , respectively). Considering the overall population, significantly higher rates of newly formed bone were obtained in mandibular sites, while non-mineralized and dense connective tissue rates were higher in the maxilla (p < .05). CONCLUSIONS: The application of collagen membrane over titanium mesh did not lead to significant results. Bone formation appeared significantly different in the maxilla compared with the mandible. Additional studies are required to further investigate the issues observed.

Finishing technique effect on strength of zirconia-reinforced lithium silicate ceramic.

The aim of this study was to evaluate the effect of two finishing techniques, glazing or polishing, in comparison with the as-cut condition, on the biaxial-flexural-strength (BFS) of a zirconia-reinforced lithium silicate ceramic (ZLS). Cylinders were milled from CAD/CAM blocks and sliced to obtain disc-shaped specimens (ISO6872:2015). Polished and glazed specimens were processed following the manufacturer's instructions. Thirty-three specimens were obtained for each condition and microstructural and BFS/fractographic characterizations were performed. BFS and roughness data were analyzed using Weibull statistics and ANOVA one-way with Tukey post-hoc test, respectively. While a rougher surface was observed for as-cut specimens, smoother surfaces were observed for polished and glazed ZLS at microscopical evaluation and confirmed through surface-roughness evaluation. X-ray spectra depicted a glass phase for all groups and characteristic metasilicate, lithium disilicate, and lithium phosphate peaks for the as-cut and polished specimens. Glazed specimens showed higher characteristic strength than polished and as-cut specimens, which did not differ significantly. While higher Weibull-modulus was observed for the polished than for the as-cut specimens, no statistically significant differences were noted between glazed and polished, and between glazed and as-cut specimens. ZLS presents higher strength when glazed, and polishing increases the structural reliability of the material relative to the as-cut condition. Both finishing techniques reduced surface roughness similarly.

Effects of erosion and abrasion on resin-matrix ceramic CAD/CAM materials: An in vitro investigation.

The aim of the study was to evaluate the effects of erosion and abrasion on resin-matrix ceramic CAD/CAM materials [CERASMART (GC); VITA ENAMIC (VITA Zahnfabrik); Lava Ultimate (3 M)] in comparison to feldspar ceramic (VITABLOCS Mark II, VITA Zahnfabrik) and resin composite materials (ceram.x universal, Dentsply Sirona). Daily brushing and acid exposure were simulated using a brushing apparatus and a solution of 0.5 vol% citric acid. Microhardness, surface roughness, and substance loss were measured at baseline and after simulation of 1 and 3 years of function. All materials showed a decrease in microhardness after 3 years and an increase in surface roughness (Ra) after 1 and 3 years. The Ra increase was statistically significantly lower for the resin-matrix ceramics than for feldspar ceramic and similar to composite material. After 3 years, only feldspar ceramic showed no significant substance loss. In conclusion, resin-matrix ceramics demonstrate reduced roughening compared to feldspar ceramics, potentially improving restoration longevity by preventing plaque buildup, but differences in abrasion resistance suggest the need for further material-specific research. Future research should aim to replicate clinical conditions closely and to transition to in vivo trials.

Influence of different immediate dentin sealing strategies on bond strength of indirect resin nanoceramic restorations.

In this study, we evaluated the effect of four different strategies for bonding a CAD/CAM resin nanoceramic restoration (Lava Ultimate, 3M) to the dentin surface using a universal adhesive (Scotch Bond Universal, 3M) and adhesive resin cement (RelyX Ultimate, 3M) on the shear bond strength (SBS) and failure mode. The strategies comprised: (i) immediate sealing, immediate bonding; (ii) immediate sealing, bonding after 2 weeks with provisional restoration; (iii) immediate sealing with flowable resin composite reinforcement and bonding after 2 weeks with provisional restoration; and (iv) no immediate sealing, and bonding after 2 weeks with provisional restoration. After bonding, all the specimens were thermocycled, shear tests were performed using a universal testing machine, and failure modes were determined using stereomicroscope and scanning electron microscopy. The highest mean SBS was recorded with immediate sealing, immediate bonding strategy. Most adhesive failures with exposed dentinal tubules were noted in specimens exposed to bonding after 2 weeks with no immediate sealing, which was associated with the lowest SBS. Mixed failures predominated in all immediate dentin sealing groups. Immediate sealing with universal adhesives improves SBS, particularly in the single-visit approach, which has shown significantly better performance, whereas the provisional phase has a negative effect.

Effect of peroxide-free and peroxide-based in-office bleaching on the surface and mechanical properties of CAD/CAM esthetic restorative materials.

The study aimed to investigate the influence of H2O2-based and H2O2-free in-office bleaching on the surface and mechanical attributes of CAD/CAM composite blocks. CAD/CAM composite blocks from five different composite materials (CC1, CC2, CC3, CC4, and CC5) were randomly divided into two groups according to bleaching application (H2O2-based and H2O2-free). The surface topography, morphology, nanohardness, elastic modulus, flexural strength, and fracture toughness were measured. A paired and unpaired sample t-tests gauged the effect of pre- and post-bleaching on the substrates. The estimated mean differences (before-after bleaching) suggested an increase in surface roughness for two materials CC2 and CC4, and a significant decrease in nanohardness for material CC4 and in elastic modulus for materials CC2 and CC4 with H2O2-based bleaching, whereas H2O2-free bleaching resulted in changes compatible with no change in these properties. Flexural strength and fracture toughness showed no evidence of changes, irrespective of the bleaching gel used. Scanning electron microscopic analysis revealed erosive effects and micropore formation due to H2O2-based bleaching. H2O2-based bleaching deteriorates the surface of CAD/CAM composite materials while H2O2-free bleaching gel had an insignificant effect on both surface and bulk properties. The clinician should carefully evaluate the potential effects of H2O2-based bleaching on the surface properties of CAD/CAM composites.

Effect of laser irradiation during in-office tooth bleaching on surface properties of resin-based restorative materials.

This study evaluated the changes in surface properties of three resin-based restorative materials after two laser-assisted, in-office tooth bleaching protocols using erbium, chromium: yttrium-scandium-gallium-garnet (Er,Cr:YSGG) or diode (980 nm) lasers. A nanohybrid composite (Enamel Plus HRi), a Bis-GMA-free composite (Enamel Plus HRi Bio Function), and a resin-matrix CAD-CAM ceramic (Shofu Block HC) were tested. Forty specimens for each material were prepared and divided into four groups (n = 10/group). The control specimens did not undergo any bleaching treatment, whereas group 2 received bleaching with 40% hydrogen peroxide (H2O2), while groups 3 and 4 underwent the same bleaching procedure with the use of diode (980 nm) or Er,Cr:YSGG lasers, respectively. Surface microhardness and roughness measurements were conducted using a Vickers tester and an optical profilometer. Microhardness was lower in bleached specimens, with the nanohybrid composite exhibiting the largest difference from the no bleaching group. For the Bis-GMA-free composite the microhardness difference between no bleaching and laser-assisted bleaching were smaller than seen for the conventional bleaching technique. Surface roughness was higher in bleached specimens, with nanohybrid composite showing the largest differences from the control specimens. The examined laser-assisted tooth bleaching protocols were found not to impact surface microhardness and roughness of the tested resin-based specimens and they are deemed suitable for clinical use.

Efficacy of denture cleansers on Candida albicans adhesion and their effects on the properties of conventional, milled CAD/CAM, and 3D-printed denture bases.

OBJECTIVES: Evaluate the efficacy of denture cleaners on the adhesion of Candida albicans and their effects on the surface, optical, and mechanical properties of resins for conventional, milled, and 3D-printed denture bases. MATERIALS AND METHODS: A total of 240 resin samples were made, 120 for testing Candida albicans adhesion, optical stabilities (ΔE00), roughness (Ra), hydrophilicity (°), surface free energy (Owens-Wendt) and 120 samples for testing Candida albicans adhesion, surface microhardness (Knoop), flexural strength and modulus of elasticity in a three-point test, in which they were divided into 3 groups of denture resin (n = 40) and subdivided into 5 cleaners of dentures (n = 8). Data were evaluated by two-way ANOVA and Tukey's test for multiple comparisons (α = 0.05). RESULTS: Denture cleaners with an alkaline solution and dilute acid composition were those that showed the greatest effectiveness in reducing Candida albicans (P < 0.001), however 1% NaOCl significantly affected the properties of the resins (P < 0.05). Denture 3D-printed showed that the surface microhardness was significantly lower for all cleansers (P < 0.05). CONCLUSIONS: Listerine demonstrated superior efficacy in reducing Candida albicans with minimal effect on denture properties, whereas 1% NaOCl had a significant negative impact on the properties. The mechanical properties were significantly lower in 3D-printed resin than in other resins for all denture cleansers. CLINICAL RELEVANCE: Denture base materials are being sold to adapt to the CAD/CAM system, increasing the number of users of dentures manufactured with this system. Despite this, there is little investigation into denture cleaners regarding the adhesion capacity of microorganisms and the optical, surface and mechanical properties of dentures, thus requiring further investigation.

Biofilm inhibition of denture cleaning tablets and carvacrol on denture bases produced with different techniques.

OBJECTIVES: This study compares the biofilm inhibition effects of denture cleaning tablets, carvacrol, and their combined use against Candida albicans on denture bases produced with different techniques. Additionally, the surface roughness and contact angles of these denture bases were evaluated. MATERIALS AND METHODS: Test samples were prepared from four different denture base materials (cold-polymerized, heat-polymerized, CAD/CAM milling, and 3D-printed). The surface roughness and contact angles of the test samples were measured using a profilometer and goniometer, respectively. For the evaluation of biofilm inhibition, samples were divided into 5 subgroups: Corega and carvacrol, separately and combined treatments, positive (inoculated with C. albicans) and negative control (non-inoculated with C. albicans, only medium). Biofilm mass was determined using the crystal violet method. An additional prepared test sample for each subgroup was examined under scanning electron microscopy (SEM). RESULTS: The surface roughness values of the 3D-printed test samples were found to be statistically higher than the other groups (P < .001). The water contact angle of all test materials was not statistically different from each other (P > .001). Corega and carvacrol, separately and combined, significantly decreased the amount of biofilm on all surfaces (P < .0001). Treatment of corega alone and in combination with carvacrol to the 3D-printed material caused less C. albicans inhibition than the other groups (P < .001; P < .05). CONCLUSIONS: The surface roughness values of all test groups were within the clinically acceptable threshold. Although Corega and carvacrol inhibited C. albicans biofilms, their combined use did not show a synergistic effect. CLINICAL RELEVANCE: Carvacrol may be used as one of the disinfectant agents for denture cleaning due to its biofilm inhibition property.

Digital technology revolutionizing mandibular fracture treatment: a comparative analysis of patient-specific plates and conventional titanium plates.

OBJECTIVES: The treatment of fractures prioritizes the restoration of functionality through the realignment of fractured segments. Conventional methods, such as titanium plates, have been employed for this purpose; however, certain limitations have been observed, leading to the development of patient-specific plates. Furthermore, recent advancements in digital technology in dentistry enable the creation of virtual models and simulations of surgical procedures. The aim was to assess the clinical effectiveness of patient-specific plates utilizing digital technology in treating mandibular fractures compared to conventional titanium plates. MATERIALS AND METHODS: Twenty patients diagnosed with mandibular fractures were included and randomly assigned to either the study or control groups. The surgical procedure comprised reduction and internal fixation utilizing patient-specific plates generated through virtual surgery planning with digital models for the study group, while the control group underwent the same procedure with conventional titanium plates. Assessment criteria included the presence of malunion, infection, sensory disturbance, subjective occlusal disturbance and occlusal force in functional maximum intercuspation (MICP). Statistical analysis involved using the Chi-square test and one-way repeated measures analysis of variance. RESULTS: All parameters showed no statistically significant differences between the study and control groups, except for the enhancement in occlusal force in functional MICP, where a statistically significant difference was observed (p = 0.000). CONCLUSION: Using patient-specific plates using digital technology has demonstrated clinical effectiveness in treating mandibular fractures, offering advantages of time efficiency and benefits for less experienced surgeons. CLINICAL RELEVANCE: Patient-specific plates combined with digital technology can be clinically effective in mandibular fracture treatment.

Maxillomandibular relationship record methods for computer-engineered complete dentures: a scoping review.

OBJECTIVES: The purpose of this scoping review was to identify different methods employed for recording the maxillomandibular relationship (MMR) for computer-aided designed and manufactured (CAD-CAM) complete dentures (CDs). MATERIALS AND METHODS: This scoping review followed the PRISMA-ScR guidelines and was developed according to Arksey and O'Malley and The Joanna Briggs Institute protocol. The methods were registered on the Open Science Framework (< osf.io/rf4xm> ). The focus question was: "What are the different techniques for recording the maxillomandibular relationship in the digital workflow used in CECDs?" Two investigators searched 3 online databases [MEDLINE (PubMed), Scopus, and Science Direct] independently. The inclusion criteria were clinical studies and reviews that assessed techniques for recording MMR using digital workflow for manufacturing of CECDs. A descriptive analysis was performed considering the study design, manufacturing system, clinical steps, and tools for the determination of MMR, and the difficulty level of procedures. RESULTS: 4779 articles were identified in the electronic search and 10 studies were included for data analysis. The review identified 4 commercially available CAD-CAM denture systems and 3 innovative methods suitable for abbreviating the number of appointments (2 to 4 visits). The trial denture is inherent to the procedure for the Baltic System and 3 innovative techniques. Three techniques (2 innovative and WholeYouNexteeth) demonstrated lower difficulty levels for performing the clinical procedures, regardless of the professional skills. CONCLUSIONS: The commercially available and innovative techniques for the recording of MMR may provide predictability of the treatment. The techniques are effective, however, rely on the learning curve and the patient's clinical condition. CLINICAL RELEVANCE: Recording of the maxillomandibular relationship is paramount for the manufacturing and functionality of complete dentures. Clinicians should be aware of the different tools and techniques described for registering the jaw relationship.

Effect of cement type on vertical marginal discrepancy and residual excess cement in screwmentable and cementable implant-supported monolithic zirconia crowns.

The purpose of this study was to investigate the vertical marginal discrepancy (VMD) and residual excess cement (REC) of cementable and screwmentable monolithic zirconia crowns cemented with different types of cement. Abutments were attached to 40 implant analogues. Crowns were created using computer-aided design/computer-aided manufacturing technology from monolithic zirconia blocks, either with or without a screw access hole (SAC). Crowns created both ways were split into two groups and cemented with resin and zinc polycarboxylate cement under a 5-kg weight. VMD and REC values were evaluated using an X20 zoom stereomicroscope. Data were analysed using two-way ANOVA and the Bonferroni test. According to the two-way ANOVA results, REC measurements differed significantly in the crown design and cement groups. However, whilst VMD values were significantly different in both crown design groups, there was no significant difference in the cement groups. According to the Bonferroni test results, the highest REC (157.241 ± 44.29 µm) and VMD (68.052 ± 16.19 µm) values were found in the crowns without SAC and cemented with zinc polycarboxylate. Screwmentable crowns are more effective than cementable crowns in reducing REC and VMD. Whilst polycarboxylate cement reduces VMD in screwmentable crowns, resin cement is more suitable for cementable crowns.

Impact of liner treatment on the translucency of CAD/CAM multi-colored lithium disilicate and multi-layered zirconia implant-supported crowns, and evaluation of fracture strength of ceramic crowns.

This study aimed to evaluate the optical properties of liner-treated CAD/CAM Multi-colored lithium disilicate (Amber Mill Direct; AMD) and multi-layered zirconia (Omega multi; OM) implant-supported crowns, as well as their effect on the fracture strength of Ti or Zr abutments to which they were applied. After sintering AMD and OM ceramic blocks, they were classified into three groups: untreated, liner-treated, and liner-treated with added color. Optical properties were evaluated by analyzing color differences using background materials to assess translucency and the masking ability of liner-treated ceramics. Subsequently, the fracture strength of implant-supported crowns applied to Ti or Zr abutments was measured, and statistical analysis was conducted using Weibull statistics. Untreated AMD exhibited the highest translucency. Liner treatment reduced translucency in both ceramics, while color-added liner treatment increased translucency. Liner-treated AMD showed greater color difference compared to OM, whereas color-added liner treatment reduced the color difference. Fracture strength was highest in Ti abutment-OM crowns (548.03 N) and lowest in Zr abutment-AMD crowns (283.58 N). Additionally, the Weibull coefficient was over twice as high in Ti abutment-AMD crowns (m = 17.500). Color liners can adjust the high translucency of lithium disilicate ceramics to block discoloration, providing natural tooth-like color and enabling the creation of esthetic restorations. Furthermore, lithium disilicate ceramic crowns applied to Ti abutments exhibited high Weibull coefficients and fracture strengths.

The effect of various surface treatments on the repair bond strength of denture bases produced by digital and conventional methods.

There is limited information on the repairability of prostheses produced with digital technology. This study aims to evaluate various surface treatments on flexural bond strength of repaired dentured base resins produced by digital and conventional methods. A total of 360 samples were prepared from one heat-polymerized, one CAD/CAM milled and one 3D printed denture base materials. All of the test samples were subjected to thermocycling (5-55 °C, 5000 cycles) before and after repair with auto-polymerizing acrylic resin. The test samples were divided into five subgroups according to the surface treatment: grinding with silicon carbide (SC), sandblasting with Al2O3 (SB), Er:YAG laser (L), plasma (P) and negative control (NC) group (no treatment). In addition, the positive control (PC) group consisted of intact samples for the flexural strength test. Surface roughness measurements were performed with a profilometer. After repairing the test samples, a universal test device determined the flexural strength values. Both the surface topography and the fractured surfaces of samples were examined by SEM analysis. The elemental composition of the tested samples was analyzed by EDS. Kruskal-Wallis and Mann-Whitney U tests were performed for statistical analysis of data. SB and L surface treatments statistically significantly increased the surface roughness values of all three materials compared to NC subgroups (p < 0.001). The flexural strength values of the PC groups in all three test materials were significantly higher than those of the other groups (p < 0.001). The repair flexural strength values were statistically different between the SC-SB, L-SB, and NC-SB subgroups for the CAD/CAM groups, and the L-SC and L-NC subgroups for the 3D groups (p < 0.001). The surface treatments applied to the CAD/CAM and heat-polymerized groups did not result in a statistically significant difference in the repair flexural strength values compared to the NC groups (p > 0.05). Laser surface treatment has been the most powerful repair method for 3D printing technique. Surface treatments led to similar repair flexural strengths to untreated groups for CAD/CAM milled and heat-polymerized test samples.