A closer look at high-energy X-ray-induced bubble formation during soft tissue imaging.

Improving the scalability of tissue imaging throughput with bright, coherent X-rays requires identifying and mitigating artifacts resulting from the interactions between X-rays and matter. At synchrotron sources, long-term imaging of soft tissues in solution can result in gas bubble formation or cavitation, which dramatically compromises image quality and integrity of the samples. By combining in-line phase-contrast imaging with gas chromatography in real time, we were able to track the onset and evolution of high-energy X-ray-induced gas bubbles in ethanol-embedded soft tissue samples for tens of minutes (two to three times the typical scan times). We demonstrate quantitatively that vacuum degassing of the sample during preparation can significantly delay bubble formation, offering up to a twofold improvement in dose tolerance, depending on the tissue type. However, once nucleated, bubble growth is faster in degassed than undegassed samples, indicating their distinct metastable states at bubble onset. Gas chromatography analysis shows increased solvent vaporization concurrent with bubble formation, yet the quantities of dissolved gasses remain unchanged. By coupling features extracted from the radiographs with computational analysis of bubble characteristics, we uncover dose-controlled kinetics and nucleation site-specific growth. These hallmark signatures provide quantitative constraints on the driving mechanisms of bubble formation and growth. Overall, the observations highlight bubble formation as a critical yet often overlooked hurdle in upscaling X-ray imaging for biological tissues and soft materials and we offer an empirical foundation for their understanding and imaging protocol optimization. More importantly, our approaches establish a top-down scheme to decipher the complex, multiscale radiation-matter interactions in these applications.

An Experimental and Numerical Investigation on Bubble Growth in Polymeric Foams.

The cellular morphology of thermoplastic polymeric foams is a key factor for their performances. Three possible foam morphologies exist, namely, with closed cells, interconnected cellular structure, and open cells. In the gas foaming technology, a physical blowing agent, e.g., CO2 or N2, is used to form bubbles at high pressure in softened/melted polymers. As a consequence of a pressure quench, the bubbles grow in the liquid matrix until they impinge and possibly break the thin liquid films among them. If film breakage happens, the broken film may retract due to the elastic energy accumulated by the polymeric liquid during the bubble growth. This, in turn, determines the final morphology of the foam. In this work, we experimentally study the growth of CO2 bubbles in a poly(e-caprolactone) (PCL) matrix under different pressure conditions. In addition, we perform three-dimensional direct numerical simulations to support the experimental findings and rationalize the effects of the process parameters on the elastic energy accumulated in the liquid at the end of the bubble growth, and thus on the expected morphology of the foam. To do that, we also extend the analytic model available in the literature for the growth of a single bubble in a liquid to the case of a liquid with a multi-mode viscoelastic constitutive equation.

Switching Propulsion Mechanisms of Tubular Catalytic Micromotors.

Different propulsion mechanisms have been suggested for describing the motion of a variety of chemical micromotors, which have attracted great attention in the last decades due to their high efficiency and thrust force, enabling several applications in the fields of environmental remediation and biomedicine. Bubble-recoil based motion, in particular, has been modeled by three different phenomena: capillary forces, bubble growth, and bubble expulsion. However, these models have been suggested independently based on a single influencing factor (i.e., viscosity), limiting the understanding of the overall micromotor performance. Therefore, the combined effect of medium viscosity, surface tension, and fuel concentration is analyzed on the micromotor swimming ability, and the dominant propulsion mechanisms that describe its motion more accurately are identified. Using statistically relevant experimental data, a holistic theoretical model is proposed for bubble-propelled tubular catalytic micromotors that includes all three above-mentioned phenomena and provides deeper insights into their propulsion physics toward optimized geometries and experimental conditions.

Review-Physicochemical hydrodynamics of gas bubbles in two phase electrochemical systems.

Electrochemical systems suffer from poor management of evolving gas bubbles. Improved understanding of bubbles behavior helps to reduce overpotential, save energy and enhance the mass transfer during chemical reactions. This work investigates and reviews the gas bubbles hydrodynamics, behavior, and management in electrochemical cells. Although the rate of bubble growth over the electrode surface is well understood, there is no reliable prediction of bubbles break-off diameter from the electrode surface because of the complexity of bubbles motion near the electrode surface. Particle Image Velocimetry (PIV) and Laser Doppler Anemometry (LDA) are the most common experimental techniques to measure bubble dynamics. Although the PIV is faster than LDA, both techniques are considered expensive and time-consuming. This encourages adapting Computational Fluid Dynamics (CFD) methods as an alternative to study bubbles behavior. However, further development of CFD methods is required to include coalescence and break-up of bubbles for better understanding and accuracy. The disadvantages of CFD methods can be overcome by using hybrid methods. The behavior of bubbles in electrochemical systems is still a complex challenging topic which requires a better understanding of the gas bubbles hydrodynamics and their interactions with the electrode surface and bulk liquid, as well as between the bubbles itself.

Numerical investigation of acoustic cavitation and viscoelastic tissue deformation.

Acoustic cavitation and tissue deformation are studied by modifying a level-set method for compressible two-phase flows to consider viscoelastic tissue deformation. The numerical simulations performed using different shear moduli and bubble-tissue distances demonstrate various interactions between bubble and viscoelastic tissue, including inverted cone-shape bubbles, bubble migration, liquid jet formation, compressive and expansive tissue deformation, and tissue perforation. The bubble is observed to grow larger with increasing tissue bulk modulus and density. The maximum tissue deformation generally increases with decreasing initial bubble-tissue distance and with increasing tissue bulk modulus and density. The tissue shear modulus conditions that maximize tissue deformation are in the range of 1-10 MPa, unless the tissue density is very large.

A Novel In-Line Measurement and Analysis Method of Bubble Growth-Dependent Strain and Deformation Rates during Foaming.

Bubble growth processes are highly influenced by the elongational viscosity of the blowing agent-loaded polymer melt. Therefore, the elongational viscosity is an important parameter for the development of new polymers for foaming applications, as well as for the prediction of bubble growth processes. Thus, knowledge of the initial expansion and deformation behavior in dependency on the polymer, the blowing agent concentration, and the process conditions is necessary. This study presents a novel method for the in-line observation and analysis of the initial expansion and deformation behavior within the bead foam extrusion process. For this purpose, nitrogen as the blowing agent was injected into the polymer melt (PS and PLA) during the extrusion process. The in-line observation system consists of a borescope equipped with a camera, which was integrated into the water box of an underwater pelletizer. The camera is controlled by a developed trigger by means of angular step signal analysis of a rotary encoder on the cutter shaft of the underwater pelletizer. Thus, images can be taken at any time during the foaming process depending on the cutter position to the die outlet. It is shown that the developed method provides reliable results and that the differences of the initial expansion and deformation behavior during bubble growth can be analyzed in-line in dependency on real foaming process conditions and the type of polymer used.

Prediction of the Bubble Growth Behavior by Means of the Time-, Temperature-, Pressure- and Blowing Agent Concentration-Dependent Transient Elongational Viscosity Function of Polymers.

Bubble growth processes are highly complex processes, which are not only dependent on the foaming process parameters (temperature, pressure and blowing agent concentration) but also on the type and structure of the polymer used. Since the elongational viscosity at the bubble wall during bubble growth also depends on these influencing factors, the so-called transient elongational viscosity plays a key role in describing the gas bubble growth behavior in polymer melts. The model-based description of the transient elongational viscosity function is difficult due to its dependence on time, Hencky strain and strain rate. Therefore, representative viscosities or shear viscosity models are usually used in the literature to predict the bubble growth behavior. In this work, the transient equibiaxial elongational viscosity function at the bubble wall during bubble growth is described holistically for the first time. This is achieved by extending the so-called molecular stress function (MSF) model by superposition principles (temperature, pressure and blowing agent concentration) and by using the elongational deformation behavior (Hencky strain and strain rate) at the bubble wall during the initial, and thus viscosity-driven, bubble growth process. Therefore, transient uniaxial elongational viscosity measurements are performed and the non-linear MSF model parameters of the two investigated polymers PS (linear polymer chains) and PLA (long-chain branched polymer chains) are determined. By applying the superposition principles and by changing the strain mode parameter to the equibiaxial case in the MSF model, the transient equibiaxial viscosity master curve is obtained and used to describe the bubble growth process. The results show that the extended MSF model can fully predict the transient equibiaxial elongational viscosity function at the bubble wall during bubble growth processes. The bubble growth behavior over time can then be realistically described using the defined transient equibiaxial elongational viscosity function at the bubble wall. This is not possible, for example, with a representative viscosity and therefore clearly demonstrates the influence and importance of knowing the transient deformation behavior that prevails at the bubble wall during bubble growth processes.

Role of Bubble Evolution in the Bubble-Propelled Janus Micromotors.

Bubble-propelled Janus micromotors have attracted extensive attention in recent years and have been regarded as powerful tools in the environmental and medical fields due to their excellent movement ability. The movement ability can mainly be attributed to the periodic growth, detachment, and/or collapse of the bubble. However, subjected to the experimental conditions, the mechanism of bubble evolution on the motion of the micromotor could not be elucidated clearly. In this work, a finite element method was employed for exploring the role of bubble evolution in bubble-propelled Janus micromotors, which emphasized the growth and collapse of bubbles. After the proposed model was verified by the scallop theorem, the influence of the growth and rapid collapse of bubbles on micromotors was investigated. Results show that the growth and collapse of a bubble can drive the micromotor to produce a displacement, but the displacement caused by a bubble collapse is significantly greater than that caused by bubble growth. The reasons for this phenomenon are analyzed and explained. In addition to the influence of bubble size, the collapse time of the bubble is also investigated.

Flat bread baking: Single to double layer transition.

Double-layered flat bread features an impressive oven rise and delamination during baking, leading to the formation of an internal pocket capable of holding various solid foods - a key quality criterion for consumers. These breads are unique in their baking method, which requires specialized ovens and high temperatures between 350 and 550 °C. Use of high baking temperatures to achieve the double layering development (called delamination) during baking has raised concerns over excessive energy consumption. In this study, whether or not the application of fermentation (affecting the accumulation of dissolved CO2) and baking temperature (which affects gas generation) were varied and the impacts on delamination were evaluated. To complement this evaluation, dough water content and temperature were monitored during baking. In a novel manner, this study characterized water distribution in flat bread, explaining the surprising decrease of water loss with increasing baking temperature. Our study has clearly shown water vapor to be the prime cause of delamination. The role of water pressure in dough inflation and in causing the edges to detach from the deck and the heterogeneity of flat bread water content were highlighted and a concept map proposed.

Laser-Produced Cavitation Bubble Behavior in Newtonian and Non-Newtonian Liquid Inside a Rigid Cylinder: Numerical Study of Liquid Disc Microjet Impact Using OpenFOAM.

This study employs OpenFOAM to analyze the behavior of a single laser-produced cavitation bubble in a Newtonian/non-Newtonian fluid inside a rigid cylinder. This research aimed to numerically calculate the impact of liquid disc microjet resulting from the growth and collapse of the laser-produced bubble to the cylinder wall to take advantage of the cavitation phenomenon in various industrial and medical applications, such as modeling how to remove calcification lesions in coronary arteries. In addition, by introducing the main study cases in which a single bubble with different initial conditions is produced by a laser in the center/off-center of a cylinder with different orientations relative to the horizon, filled with a stationary or moving Newtonian/Non-Newtonian liquid, the general behavior of the bubble in the stages of growth and collapse and the formation of liquid disk microjet and its impact is examined. The study demonstrates that the presence of initial velocity in water affects the amount of microjet impact proportional to the direction of gravity. Moreover, the relationship between the laser energy and the initial conditions of the bubble and the disk microjet impact on the cylinder wall is expressed.

Bubble growth analysis during subcooled boiling experiments on-board the international space station: Benchmark image analysis.

This work compares four different image processing algorithms for the analysis of image data obtained during the Multiscale Boiling Experiment of ESA, executed on-board the International Space Station. Two separate experimental campaigns have been performed in 2019 and 2020, aiming to investigate boiling phenomena in microgravity, with and without the presence of shear flow and electric field. A heated substrate, at the bottom of the test cell, creates a temperature profile across the liquid bulk above it. A laser beam hits a designated microcavity at the middle of the substrate, to initiate nucleation of a single, isolated bubble. In the presence of shear flow or electric field forces, the bubble slides or detaches respectively, leaving the cavity free for the nucleation and growth of a new bubble. The growth of such a bubble within the prescribed temperature profile is studied for varying experimental conditions (i.e. pressure, heat flux, subcooling temperature) by capturing high speed, black and white video images. The presence of light reflections at random locations around the bubble contour vary with bubble size and population. This, combined with the refraction induced optical distortion of vertical image dimension close to the heater, make the accurate detection of bubbles contour a real challenge. Four research teams, namely the University of Pisa (UNIPI), the Institute of Fluid Mechanics of Toulouse (IMFT), the joint group of Aix Marseille University (AMU) and Kutateladze Institute of Thermophysics (IT), and the joined group of Aristotle University of Thessaloniki (AUTH), Technical University of Darmstadt (TUD) and Foundation of Research and Technology in Crete (FORTH), developed separate specialized algorithms to: a) detect bubble edges and b) use these edges to calculate basic bubble geometrical features, such as contact line diameter, bubble diameter and contact angles. These four different approaches diverge in complexity and concept. In the absence of reference measurements at microgravity conditions, measurements efficiency is evaluated based on the comparison of the estimated bubble geometrical features along with pertinent physical arguments. Results show that the efficiency of each approach varies with the nature of measurement. The studied benchmark dataset is published allowing other research groups to test further their own image processing algorithms.

Inline imaging reveals evolution of the size distribution and the concentration of microbubbles in dissolved air flotation.

Dissolved air flotation (DAF) is an efficient process to remove impurities from fresh or salt water. As the removal is based on the agglomeration of impurities on the generated microbubbles, the size distribution and concentration of air bubbles are key parameters in dissolved air flotation. However, the development of microbubbles in the whole flotation process remains unexplored. In this study, we show that state-of-the-art inline microscopy enables the image acquisition of bubbles in DAF. Based on image analysis, thousands of microbubbles (10-200 µm) were analyzed within 6-12 min experiments. Consequently, bubble size distributions and bubble concentrations can be determined with moderate effort. Bubble size distributions were measured in a lab-scale DAF comprising a saturation unit, a decompression valve in/after which the bubbles are formed, and the actual flotation tank. The state of the microbubbles is not only determined at different positions within the tank but also in the supply pipe from the decompression valve to the tank. All bubble size distributions were unimodal and can be described well with Burr XII distributions. For fresh water, bubble size increased while bubble concentration decreased along the supply pipe between the decompression valve and the inlet of the flotation tank, indicating bubble coalescence. Compared to freshwater, saltwater inhibited this bubble coalescence in the pipe. Within the flotation tank, the bubble size did not change drastically for neither salt- nor freshwater. However, the bubble concentration decreased for both waters, which could be explained by dilution effects. Our results demonstrate that the developed inline method is a promising tool to study the evolution of microbubbles in flotation systems. Further, it might also be applied to investigate microbubbles in other processes such as fermentation, decomposition of organic compounds, and fouling mitigation in membranes.

In Situ Investigation of Microstructural Evolution and Intermetallic Compounds Formation at Liquid Al/Solid Cu Interface by Synchrotron X-ray Radiography.

Synchrotron radiation dynamic imaging technology combined with the static characterization method was used to study the microstructural evolution and the growth kinetics of intermetallic compounds (IMCs) at the liquid Al/solid Cu interface. The results show that the interfacial microstructure can be divided into layered solid diffusion microstructures (AlCu3, Al4Cu9, Al2Cu3 and AlCu) and solidification microstructures (Al3Cu4, AlCu and Al2Cu) from the Cu side to the Al side. Meanwhile, the growth of bubbles formed during the melting, holding and solidification of an Al/Cu sample was also discussed, which can be divided into three modes: diffusion, coalescence and engulfment. Moreover, the growth of AlCu3 and (Al4Cu9 + Al2Cu3) near the Cu side is all controlled by both interfacial reaction and volume diffusion. The growth of Al3Cu4 adjacent to the melt is mainly controlled by the interfacial reaction, which plays a major role in the growth of the total IMCs.

Growth of Laser-Induced Microbubbles inside Capillary Tubes Affected by Gathered Light-Absorbing Particles.

Microbubbles have important applications in optofluidics. The generation and growth of microbubbles is a complicated process in microfluidic channels. In this paper, we use a laser to irradiate light-absorbing particles to generate microbubbles in capillary tubes and investigate the factors affecting microbubble size. The results show that the key factor is the total area of the light-absorbing particles gathered at the microbubble bottom. The larger the area of the particles at bottom, the larger the size of the microbubbles. Furthermore, the area is related to capillary tube diameter. The larger the diameter of the capillary tube, the more particles gathered at the bottom of the microbubbles. Numerical simulations show that the Marangoni convection is stronger in a capillary tube with a larger diameter, which can gather more particles than that in a capillary tube with a smaller diameter. The calculations show that the particles in contact with the microbubbles will be in a stable position due to the surface tension force.

Efficient Mesh Interface Engineering: Insights from Bubble Dynamics in Electrocatalysis.

Electrochemical catalysis offers great potential in energy and mass conversion in academy and industry. However, bubble dynamics and its influence on gas-evolving electrode systems remain ambiguous. Detailed information on the local transport process between different phases and the underlying mechanism are required for the full understanding of two-phase flow evolution and distribution. Here, we construct a three-electrode water splitting reaction system to study the bubble dynamics and system efficiency of titanium electrodes with different morphologies. The dynamics of a gas bubble at an electrode with a plate and 100-mesh, 150-mesh, and 300-mesh structures is systematically investigated with respect to applied voltage conditions. Parameters and underlying mechanisms that influence the two-phase flow evolution and electrochemical reaction performance are carefully discussed. Finally, the underlying dynamic force balance on the gas bubble is analyzed to illustrate the mechanism and experimental observations. Our study provides insights in gas-evolving electrocatalysis and offers opportunities for the design and fabrication of high-performance electrocatalytic reactors.

Analysis of Bubble Growth in Supercritical CO2 Extrusion Foaming Polyethylene Terephthalate Process Based on Dynamic Flow Simulation.

Bubble growth in the polymer extrusion foaming process occurs under a dynamic melt flow. For non-Newtonian fluids, this work successfully coupled the dynamic melt flow simulation with the bubble growth model to realize bubble growth predictions in an extrusion flow. The initial thermophysical properties and dynamic rheological property distribution at the cross section of the die exit were calculated based on the finite element method. It was found that dynamic rheological properties provided a necessary solution for predicting bubble growth during the supercritical CO2 polyethylene terephthalate (PET) extrusion foaming process. The introduction of initial melt stress could effectively inhibit the rapid growth of bubbles and reduce the stable size of bubbles. However, the initial melt stress was ignored in previous work involving bubble growth predictions because it was not available. The simulation results based on the above theoretical model were consistent with the evolution trends of cell morphology and agreed well with the actual experimental results.

Numerical study of the effect of liquid compressibility on acoustic droplet vaporization.

In acoustic droplet vaporization (ADV), a cavitated bubble grows and collapses depending on the pressure amplitude of the acoustic pulse. During the bubble collapse, the surrounding liquid is compressed to high pressure, and liquid compressibility can have a significant impact on bubble behavior and ADV threshold. In this work, a one-dimensional numerical model considering liquid compressibility is presented for ADV of a volatile microdroplet, extending our previous Rayleigh-Plesset based model [Ultrason. Chem. 71 (2021) 105361]. The numerical results for bubble motion and liquid energy change in ADV show that the liquid compressibility highly inhibits bubble growth during bubble collapse and rebound, especially under high acoustic frequency conditions. The liquid compressibility effect on the ADV threshold is quantified with varying acoustic frequencies and amplitudes.

Effects of beverage carbonation on lubrication mechanisms and mouthfeel.

The perception of carbonation is an important factor in beverage consumption which must be understood in order to develop healthier products. Herein, we study the effects of carbonated water on oral lubrication mechanisms involved in beverage mouthfeel and hence taste perception. Friction was measured in a compliant PDMS-glass contact simulating the tongue-palate interface (under representative speeds and loads), while fluorescence microscopy was used to visualise both the flow of liquid and oral mucosal pellicle coverage. When carbonated water is entrained into the contact, CO2 cavities form at the inlet, which limit flow and thus reduce the hydrodynamic pressure. Under mixed lubrication conditions, when the fluid film thickness is comparable to the surface roughness, this pressure reduction results in significant increases in friction (>300% greater than under non-carbonated water conditions). Carbonated water is also shown to be more effective than non-carbonated water at debonding the highly lubricious, oral mucosal pellicle, which again results in a significant increase in friction. Both these transient mechanisms of starvation and salivary pellicle removal will modulate the flow of tastants to taste buds and are suggested to be important in the experience of taste and refreshment. For example this may be one reason why flat colas taste sweeter.

An Experimental Study on Bubble Growth in Laponite RD as Thixotropic Yield Material.

The growth and release of the leading major bubble at the tip of a needle in the thixotropic yield material Laponite RD was different from subsequent minor bubbles. The gas injection experiments combined with high-speed camera were conducted. The results showed that the shape of the major bubbles transformed from an inverted carrot shape to an inverted teardrop shape, while the shape of the minor bubbles tended to be elliptical. In addition, the pressure of bubble emergence consisted of hydrostatic pressure, capillary pressure, and cracking pressure. The major and minor bubbles differed only in the cracking pressure. The pressure when the minor bubble detached could be estimated from the lateral hydrostatic pressure. It can be deduced from dimensionless numbers that buoyancy and viscous forces were, respectively, the main driving force and resistance of bubble growth. The yield stress of Laponite RD and inertial force at the initial moment resulted in distinctive behavior of the major bubble. In addition to the viscosity resistance, surface tension, and hydrostatic pressure had a non-negligible influence on minor bubbles and still accounted for 10-20% of the total resistance in the later stage but less than 5% in major bubble growth.

Surface Bubble Growth in Plasmonic Nanoparticle Suspension.

Understanding the growth dynamics of the microbubbles produced by plasmonic heating can benefit a wide range of applications like microfluidics, catalysis, micropatterning, and photothermal energy conversion. Usually, surface plasmonic bubbles are generated on plasmonic structures predeposited on the surface subject to laser heating. In this work, we investigate the growth dynamics of surface microbubbles generated in plasmonic nanoparticle (NP) suspension. We observe much faster bubble growth rates compared to those in pure water with surface plasmonic structures. Our analyses show that the volumetric heating effect around the surface bubble due to the existence of NPs in the suspension is the key to explaining this difference. Such volumetric heating increases the temperature around the surface bubble more efficiently compared to surface heating which enhances the expelling of dissolved gas. We also find that the bubble growth rates can be tuned in a very wide range by changing the concentration of NPs, besides laser power and dissolved gas concentration.