Increased solar-driven chemical transformations through surface-induced benzoperylene aggregation in dye-sensitized photoanodes.

The impact of benzo[ghi]perylenetriimide (BPTI) dye aggregation on the performance of photoelectrochemical devices was explored, through imide-substitution with either alkyl (BPTI-A, 2-ethylpropyl) or bulky aryl (BPTI-B, 2,6-diisopropylphenyl) moieties, to, respectively, enable or suppress aggregation. While both dyes demonstrated similar monomeric optoelectronic properties in solution, adsorption onto mesoporous SnO2 revealed different behavior, with BPTI-A forming aggregates via π-stacking and BPTI-B demonstrating reduced aggregation in the solid state. BPTI photoanodes were tested in dye-sensitized solar cells (DSSCs) before application to dye-sensitized photoelectrochemical cells (DSPECs) for Br2 production (a strong oxidant) coupled to H2 generation (a solar fuel). BPTI-A demonstrated a twofold higher dye loading of the SnO2 surface than BPTI-B, resulting in a fivefold enhancement to both photocurrent and Br2 production. The enhanced output of the photoelectrochemical systems (with respect to dye loading) was attributed to both J- and H- aggregation phenomena in BPTI-A photoanodes that lead to improved light harvesting. Our investigation provides a strategy to exploit self-assembly via aggregation to improve molecular light-harvesting and charge separation properties that can be directly applied to dye-sensitized photoelectrochemical devices.

Boron and Sodium Doping of Polymeric Carbon Nitride Photoanodes for Photoelectrochemical Water Splitting.

Polymeric carbon nitride is a promising photoanode material for water-splitting and organic transformation-based photochemical cells. Despite achieving significant progress in performance, these materials still exhibit low photoactivity compared to inorganic photoanodic materials because of a moderate visible light response, poor charge separation, and slow oxidation kinetics. Here, the synthesis of a sodium- and boron-doped carbon nitride layer with excellent activity as a photoanode in a water-splitting photoelectrochemical cell is reported. The new synthesis consists of the direct growth of carbon nitride (CN) monomers from a hot precursor solution, enabling control over the monomer-to-dopant ratio, thus determining the final CN properties. The introduction of Na and B as dopants results in a dense CN layer with a packed morphology, better charge separation thanks to the in situ formation of an electron density gradient, and an extended visible light response up to 550 nm. The optimized photoanode exhibits state-of-the-art performance: photocurrent densities with and without a hole scavenger of about 1.5 and 0.9 mA cm-2 at 1.23 V versus reversible hydrogen electrode (RHE), and maximal external quantum efficiencies of 56% and 24%, respectively, alongside an onset potential of 0.3 V.

Ligand-Engineered Quantum Dots Decorated Heterojunction Photoelectrodes for Self-Biased Solar Water Splitting.

A cost-effective and high-efficiency photoelectrochemical (PEC) water splitting system based on colloidal quantum dots (QDs) represents a potential solar-to-hydrogen (STH) conversion technology to achieve future carbon neutrality. Herein, a self-biased PEC cell consisting of BiVO4 photoanode and Cu2 O photocathode both decorated with Zn-doped CuInS2 (ZCIS) QDs is successfully fabricated. The intrinsic charge dynamics of the photoelectrodes are efficiently optimized via rational engineering of the surface ligands capped on QDs with controllable chain lengths and binding affinities to the metal oxide electrodes. It is demonstrated that the short-chain monodentate 1-dodecanethiol ligands are beneficial to ZCIS QDs for suppressing charge recombination, which enables the construction of tight heterojunction with coupled metal oxide electrodes, leading to effective photo-induced charge transfer/injection for enhanced PEC performance. The QD decorated BiVO4 and Cu2 O photoelectrodes in pairs demonstrate a self-biased PEC water splitting process, delivering an STH efficiency of 0.65% with excellent stability under AM 1.5 G one-sun illumination. The results highlight the significance of synergistic ligand and heterojunction engineering to build highly efficient and robust QDs-based PEC devices for self-biased solar water splitting.

Simultaneous Modulation of Interface Reinforcement, Crystallization, Anti-Reflection, and Carrier Transport in Sb Gradient-Doped SnO2 /Sb2 S3 Heterostructure for Efficient Photoelectrochemical Cell.

In this study, an effective quadruple optimization integrated synergistic strategy is designed to fabricate quality Sb gradient-doped SnO2 /Sb2 S3 heterostructure for an efficient photoelectrochemical (PEC) cell. The experimental results and theoretical calculations reveal that i) optical absorption matching is realized by combining the anti-reflection of SnO2 and high light absorption ability of Sb2 S3 in the visible region; ii) interface reinforcement is carried out by coordinating gradient-distributed Sb in SnO2 with S in S-rich precursor of Sb2 S3 for improving the Sb2 S3 crystallization process and matching crystalline lattice of Sb:SnO2 and Sb2 S3 ; iii) ultrahigh electron mobility is achieved by making Sb gradient-doped SnO2 ; iv) carrier separation and transport are accelerated by constructing type-II heterojunction with appropriate energy level alignment and forming a high-speed electron transport channel. All of above-mentioned optimization effects are integrated into a synergistic strategy for constructing the Sb:SnO2 /Sb2 S3 photoanode, achieving a photocurrent density of 2.30 mA cm-2 , hydrogen generation rate of 30.03 µmol cm-2 h-1 , and decent working stability. Notably, this method can also be used in other large-scale fabrication processes, such as drop-casting, spray-coating, blade-coating, printing, slot-die, etc. Moreover, this universal integrated strategy paves an avenue to fabricate efficient photoelectrodes with excellent photoelectrochemical performances.

Highly Efficient Polymeric Carbon Nitride Photoanode with Excellent Electron Diffusion Length and Hole Extraction Properties.

Polymeric carbon nitride (CN) has emerged as a promising semiconductor in photoanodes for photoelectrochemical cells (PECs) owing to its suitable electronic structure, tunable band gap, high stability, and low price. However, the poor electron diffusion within the CN layer and hole extraction to the solution still limit its applicability in PECs. Here, we report the fabrication of a CN photoanode with excellent electron diffusion length and remarkable hole extraction properties by careful design of its electronic interfaces. We combine complementary synthetic approaches to grow tightly packed CN layers forming a type-II heterojunction, which results in a CN photoanode with excellent charge separation, high electronic conductivity, and remarkable hole extraction efficiency. The optimized CN photoanode displays excellent PEC performance, reaching up to 270 µA cm-2 in a 0.1 M KOH solution at 1.23 V vs RHE, extremely low onset potential (∼0.0012 V), and long-term stability up to 18 h.

Atomically Precise Bimetallic Nanoclusters as Photosensitizers in Photoelectrochemical Cells.

The atomically precise bimetallic nanocluster (NC), Au24 Ag20 (PhCC)20 (SPy)4 Cl2 (1) (Py=pyridine), was employed for the first time as a stable photosensitizer for photoelectrochemical applications. The sensitization of TiO2 nanotube arrays (TNA) with 1 greatly enhances the light-harvesting ability of the composite because 1 shows a high molar extinction coefficient (ϵ) in the UV/Vis region. Compared to a more standard Au25 (SG)18 -TNA (2-TNA; SG=glutathione) composite, 1-TNA shows a much better stability under illumination in both neutral and basic conditions. The precise composition of the photosensitizers enables a direct comparison of the sensitization ability between 1 and 2. With the same cluster loading, the photocurrent produced by 1-TNA is 15 times larger than that of 2-TNA. The superior performance of 1-TNA over 2-TNA is attributed not only to the higher light absorption ability of 1 but also to the higher charge-separation efficiency. Besides, a ligand effect on the stability of the photoelectrode and charge-transfer between the NCs and the semiconductor is revealed. This work paves the way to study the role of metal nanoclusters as photosensitizers at the atomic level, which is essential for the design of better material for light energy conversion.

Carbon Nitride Materials for Water Splitting Photoelectrochemical Cells.

Graphitic carbon nitride materials (CNs) have emerged as suitable photocatalysts and heterogeneous catalysts for various reactions thanks to their tunable band gap, suitable energy-band position, high stability under harsh chemical conditions, and low cost. However, the utilization of CN in photoelectrochemical (PEC) and photoelectronic devices is still at an early stage owing to the difficulties in depositing high-quality and homogenous CN layer on substrates, its wide band gap, poor charge-separation efficiency, and low electronic conductivity. In this Minireview, we discuss the synthetic pathways for the preparation of various structures of CN on substrates and their underlying photophysical properties and current photoelectrochemical performance. The main challenges for CN incorporation into PEC cell are described, together with possible routes to overcome the standing limitations toward the integration of CN materials in PEC and other photoelectronic devices.

Efficient BiVO4 Photoanodes by Postsynthetic Treatment: Remarkable Improvements in Photoelectrochemical Performance from Facile Borate Modification.

Water-splitting photoanodes based on semiconductor materials typically require a dopant in the structure and co-catalysts on the surface to overcome the problems of charge recombination and high catalytic barrier. Unlike these conventional strategies, a simple treatment is reported that involves soaking a sample of pristine BiVO4 in a borate buffer solution. This modifies the catalytic local environment of BiVO4 by the introduction of a borate moiety at the molecular level. The self-anchored borate plays the role of a passivator in reducing the surface charge recombination as well as that of a ligand in modifying the catalytic site to facilitate faster water oxidation. The modified BiVO4 photoanode, without typical doping or catalyst modification, achieved a photocurrent density of 3.5 mA cm-2 at 1.23 V and a cathodically shifted onset potential of 250 mV. This work provides an extremely simple method to improve the intrinsic photoelectrochemical performance of BiVO4 photoanodes.

Thermodynamic and achievable efficiencies for solar-driven electrochemical reduction of carbon dioxide to transportation fuels.

Thermodynamic, achievable, and realistic efficiency limits of solar-driven electrochemical conversion of water and carbon dioxide to fuels are investigated as functions of light-absorber composition and configuration, and catalyst composition. The maximum thermodynamic efficiency at 1-sun illumination for adiabatic electrochemical synthesis of various solar fuels is in the range of 32-42%. Single-, double-, and triple-junction light absorbers are found to be optimal for electrochemical load ranges of 0-0.9 V, 0.9-1.95 V, and 1.95-3.5 V, respectively. Achievable solar-to-fuel (STF) efficiencies are determined using ideal double- and triple-junction light absorbers and the electrochemical load curves for CO2 reduction on silver and copper cathodes, and water oxidation kinetics over iridium oxide. The maximum achievable STF efficiencies for synthesis gas (H2 and CO) and Hythane (H2 and CH4) are 18.4% and 20.3%, respectively. Whereas the realistic STF efficiency of photoelectrochemical cells (PECs) can be as low as 0.8%, tandem PECs and photovoltaic (PV)-electrolyzers can operate at 7.2% under identical operating conditions. We show that the composition and energy content of solar fuels can also be adjusted by tuning the band-gaps of triple-junction light absorbers and/or the ratio of catalyst-to-PV area, and that the synthesis of liquid products and C2H4 have high profitability indices.

A Water-Splitting Carbon Nitride Photoelectrochemical Cell with Efficient Charge Separation and Remarkably Low Onset Potential.

A simple method to grow a closely packed carbon nitride (CN) film by the crystallization of CN monomers on a conductive substrate followed by a thermal condensation is reported. The as-synthesized CN exhibits excellent performance as photoanode material in a photoelectrochemical cell. Detailed (photo)electrochemical and transient absorption measurements indicate excellent charge separation properties, high hole-extraction efficiency (up to 50 %), a long electron lifetime, and low amount of defect states below the CN conduction band. Consequently, the CN photoanode exhibits a markedly low overpotential of 0.25 V versus reversible hydrogen electrode (RHE), which is comparable with the state-of-the-art metal-based photoanodes, an impressive photocurrent density of 116 µA cm-2 at 1.23 V versus RHE in an alkaline solution without sacrificial agent, as well as excellent stability over a wide pH range (0-13).

Fuel-Free Bio-photoelectrochemical Cells Based on a Water/Oxygen Circulation System with a Ni:FeOOH/BiVO4 Photoanode.

A bio-photoelectrochemical cell (BPEC) based on a fuel-free self-circulation water-oxygen-water system was fabricated. It consists of Ni:FeOOH modified n-type bismuth vanadate (BiVO4 ) photoanode and laccase catalyzed biocathode. In this BPEC, irradiation of the photoanode generates photocurrent for photo-oxidation of water to oxygen, which is reduced to water again at the laccase biocathode. Of note, the by-products of two electrode reactions could continue to be reacted, which means the H2 O and O2 molecules are retained in an infinite loop of water-oxygen-water without any sacrificial chemical components. As a result, the assembled fuel-free BPEC exhibits good performance with an open-circuit potential of 0.97 V and a maximum power density of 205 µW cm-2 at 0.44 V. This BPEC based on a self-circulation system offers a fuel-free model to enhance multiple energy conversion and application in reality.

In Situ Synthesis of Metal Sulfide Nanoparticles Based on 2D Metal-Organic Framework Nanosheets.

A facile in situ synthetic method is developed to synthesize metal sulfide nanoparticles based on 2D M-TCPP (M = Cu, Cd, or Co, TCPP = tetrakis(4-carboxyphenyl)porphyrin)) metal-organic framework nanosheets. The obtained CuS/Cu-TCPP composite nanosheet is used as the active material in photoelectrochemical cells, showing notably increased photocurrent due to the improved exciton separation and charge carrier transport.

A Titanium-Doped SiOx Passivation Layer for Greatly Enhanced Performance of a Hematite-Based Photoelectrochemical System.

This study introduces an in situ fabrication of nanoporous hematite with a Ti-doped SiOx passivation layer for a high-performance water-splitting system. The nanoporous hematite with a Ti-doped SiOx layer (Ti-(SiOx /np-Fe2 O3 )) has a photocurrent density of 2.44 mA cm(-2) at 1.23 VRHE and 3.70 mA cm(-2) at 1.50 VRHE . When a cobalt phosphate co-catalyst was applied to Ti-(SiOx /np-Fe2 O3 ), the photocurrent density reached 3.19 mA cm(-2) at 1.23 VRHE with stability, which shows great potential of the use of the Ti-doped SiOx layer with a synergistic effect of decreased charge recombination, the increased number of active sites, and the reduced hole-diffusion pathway from the hematite to the electrolyte.

Phosphine-free, low-temperature synthesis of tetrapod-shaped CdS and its hybrid with Au nanoparticles.

Tetrapod-shaped CdS colloidal nanocrystals are synthesized using a facile, phosphine-free synthesis approach at low temperature. The arm length and diameter of CdS tetrapods can be easily tuned by using different source of sulphureous precursors, i.e., sulfur powder, thioacetamide, and sodium diethyldithiocarbamate. Moreover, the growth of Au nanoparticles onto CdS to form metal-semiconductor hybrid nanocrystals is also demonstrated. The tetrapod-shaped CdS nanocrystals exhibit strong arm-diameter-dependent absorption and photoluminescence characteristics. Importantly, the as-obtained CdS tetrapods exhibit promising photocatalytic activity for the water-splitting reaction in photoelectrochemical cells.

Au nanoparticle-modified MoS2 nanosheet-based photoelectrochemical cells for water splitting.

The surface plasmon resonance of Au nanoparticle on MoS2 nanosheet is successfully measured by the electron energy-loss spectroscopy. Furthermore, Au-MoS2 composite is developed as the photoanode material in the photo-electronchemical cell (PEC) for water splitting. Compared to the pure MoS2 -based PEC, Au-MoS2 based PEC shows the enhanced performance in the photocatalytic water splitting.

The Emergence of High-Performance Conjugated Polymer/Inorganic Semiconductor Hybrid Photoelectrodes for Solar-Driven Photoelectrochemical Water Splitting.

Solar-driven photoelectrochemical (PEC) energy conversion holds great potential in converting solar energy into storable and transportable chemicals or fuels, providing a viable route toward a carbon-neutral society. Conjugated polymers are rapidly emerging as a new class of materials for PEC water splitting. They exhibit many intriguing properties including tunable electronic structures through molecular engineering, excellent light harvesting capability with high absorption coefficients, and facile fabrication of large-area thin films via solution processing. Recent advances have indicated that integrating rationally designed conjugated polymers with inorganic semiconductors is a promising strategy for fabricating efficient and stable hybrid photoelectrodes for high-efficiency PEC water splitting. This review introduces the history of developing conjugated polymers for PEC water splitting. Notable examples of utilizing conjugated polymers to broaden the light absorption range, improve stability, and enhance the charge separation efficiency of hybrid photoelectrodes are highlighted. Furthermore, key challenges and future research opportunities for further improvements are also presented. This review provides an up-to-date overview of fabricating stable and high-efficiency PEC devices by integrating conjugated polymers with state-of-the-art semiconductors and would have significant implications for the broad solar-to-chemical energy conversion research.

Amine-Rich Hydrogels for Molecular Nanoarchitectonics of Photosystem II and Inverse Opal TiO2 toward Solar Water Oxidation.

Solar water oxidation is a crucial process in light-driven reductive synthesis, providing electrons and protons for various chemical reductions. Despite advances in light-harvesting materials and cocatalysts, achieving high efficiency and stability remains challenging. In this study, we present a simple yet effective strategy for immobilizing natural photosystems (PS) made of abundant and inexpensive elements, using amine-rich polyethylenimine (PEI) hydrogels, to fabricate organic/inorganic hybrid photoanodes. Natural PS II extracted from spinach was successfully immobilized on inverse opal TiO2 photoanodes in the presence of PEI hydrogels, leading to greatly enhanced solar water oxidation activity. Photoelectrochemical (PEC) analyses reveal that PS II can be immobilized in specific orientations through electrostatic interactions between the positively charged amine groups of PEI and the negatively charged stromal side of PS II. This specific orientation ensures efficient photogenerated charge separation and suppresses undesired side reactions such as the production of reactive oxygen species. Our study provides an effective immobilization platform and sheds light on the potential utilization of PS II in PEC water oxidation.

NC Meets CN: Porous Photoanodes with Polymeric Carbon Nitride/ZnSe Nanocrystal Heterojunctions for Photoelectrochemical Applications.

The utilization of photoelectrochemical cells (PEC) for converting solar energy into fuels (e.g., hydrogen) is a promising method for sustainable energy generation. We demonstrate a strategy to enhance the performance of PEC devices by integrating surface-functionalized zinc selenide (ZnSe) semiconductor nanocrystals (NCs) into porous polymeric carbon nitride (CN) matrices to form a uniformly distributed blend of NCs within the CN layer via electrophoretic deposition (EPD). The achieved type II heterojunction at the CN/NC interface exhibits intimate contact between the NCs and the CN backbone since it does not contain insulating binders. This configuration promotes efficient charge separation and suppresses carrier recombination. The reported CN/NC composite structure serves as a photoanode, demonstrating a photocurrent density of 160 ± 8 µA cm-2 at 1.23 V vs a reversible hydrogen electrode (RHE), 75% higher compared with a CN-based photoelectrode, for approximately 12 h. Spectral and photoelectrochemical analyses reveal extended photoresponse, reduced charge recombination, and successful charge transfer at the formed heterojunction; these properties result in enhanced PEC oxygen production activity with a Faradaic efficiency of 87%. The methodology allows the integration of high-quality colloidal NCs within porous CN-based photoelectrodes and provides numerous knobs for tuning the functionality of the composite systems, thus showing promise for achieving enhanced solar fuel production using PEC.

Selective Valorization of Glycerol to Formic Acid on a BiVO4 Photoanode through NiFe Phenolic Networks.

The integration of the glycerol oxidation reaction (GOR) with the hydrogen evolution reaction in photoelectrochemical (PEC) cells is a desirable alternative to PEC water splitting since a large quantity of glycerol is easily accessible as the byproduct from the biodiesel industry. However, the PEC valorization of glycerol to the value-added products suffers from low Faradaic efficiency and selectivity, especially in acidic conditions, which is beneficial for hydrogen production. Herein, by loading bismuth vanadate (BVO) with a robust catalyst composed of phenolic ligands (tannic acid) coordinated with Ni and Fe ions (TANF), we demonstrate a modified BVO/TANF photoanode for the GOR with a remarkable Faradaic efficiency of over 94% to value-added molecules in a 0.1 M Na2SO4/H2SO4 (pH = 2) electrolyte. The BVO/TANF photoanode achieved a high photocurrent of 5.26 mA·cm-2 at 1.23 V versus reversible hydrogen electrode under 100 mW/cm2 white light irradiation for formic acid production with 85% selectivity, equivalent to 573 mmol/(m2·h). Transient photocurrent and transient photovoltage techniques and electrochemical impedance spectroscopy along with intensity-modulated photocurrent spectroscopy indicated that the TANF catalyst could accelerate hole transfer kinetics and suppress charge recombination. Comprehensive mechanistic investigations reveal that the GOR is initiated by the photogenerated holes of BVO, while the high selectivity to formic acid is attributed to the selective adsorption of primary hydroxyl groups in glycerol on TANF. This study provides a promising avenue for highly efficient and selective formic acid generation from biomass in acid media via PEC cells.

Artificial Photosynthesis: Current Advancements and Future Prospects.

Artificial photosynthesis is a technology with immense potential that aims to emulate the natural photosynthetic process. The process of natural photosynthesis involves the conversion of solar energy into chemical energy, which is stored in organic compounds. Catalysis is an essential aspect of artificial photosynthesis, as it facilitates the reactions that convert solar energy into chemical energy. In this review, we aim to provide an extensive overview of recent developments in the field of artificial photosynthesis by catalysis. We will discuss the various catalyst types used in artificial photosynthesis, including homogeneous catalysts, heterogeneous catalysts, and biocatalysts. Additionally, we will explore the different strategies employed to enhance the efficiency and selectivity of catalytic reactions, such as the utilization of nanomaterials, photoelectrochemical cells, and molecular engineering. Lastly, we will examine the challenges and opportunities of this technology as well as its potential applications in areas such as renewable energy, carbon capture and utilization, and sustainable agriculture. This review aims to provide a comprehensive and critical analysis of state-of-the-art methods in artificial photosynthesis by catalysis, as well as to identify key research directions for future advancements in this field.