Overview of Inorganic Electrolytes for All-Solid-State Sodium Batteries.

All-solid-state sodium batteries (AS3B) emerged as a strong contender in the global electrochemical energy storage market as a replacement for current lithium-ion batteries (LIB) owing to their high abundance, low cost, high safety, high energy density, and long calendar life. Inorganic electrolytes (IEs) are highly preferred over the conventional liquid and solid polymer electrolytes for sodium-ion batteries (SIBs) due to their high ionic conductivity (∼10-2-10-4 S cm-1), wide potential window (∼5 V), and overall better battery performances. This review discusses the bird's eye view of the recent progress in inorganic electrolytes such as Na-ß"-alumina, NASICON, sulfides, antipervoskites, borohydride-type electrolytes, etc. for AS3Bs. Current state-of-the-art inorganic electrolytes in correlation with their ionic conduction mechanism present challenges and interfacial characteristics that have been critically reviewed in this review. The current challenges associated with the present battery configuration are overlooked, and also the chemical and electrochemical stabilities are emphasized. The substantial solution based on ongoing electrolyte development and promising modification strategies are also suggested.

Polyethylene glycol embedded reduced graphene oxide supramolecular assemblies for enhanced room-temperature gas sensors.

Herein, we present the gas-dependent electrical properties of a reduced graphene oxide nanocomposite. The reduced graphene oxide (rGO) was synthesized by reducing GO with sodium borohydride (NaBH4). As-synthesized rGO was dispersed in DI water containing 1, 2, 3, 4, and 5 wt% polyethylene glycol (PEG) to prepare PEG-rGO supramolecular assemblies. The successful preparation of supramolecular assemblies was verified by their characterization using XRD, FESEM, EDS, TEM, FTIR, and Raman spectroscopy. At room temperature, the gas-dependent electrical properties of these supramolecular assemblies were investigated. The results showed that sensors composed of PEG-rGO supramolecular assemblies performed better against benzene and methanol at 3% and 4% PEG, respectively. However, high selectivity and a wide range of activation energies (∼1.64-1.91 eV) were observed for H2 gas for 4% PEG-modified supramolecular assemblies. The PEG-rGO supramolecular assemblies may be an excellent candidate for constructing ultrahigh-performance gas sensors for a variety of applications due to their high sensitivity and selectivity.

Mechanically-robust electrospun nanocomposite fiber membranes for oil and water separation.

Mechanically-robust nanocomposite membranes have been developed via crosslinking chemistry and electrospinning technique based on the rational selection of dispersed phase materials with high Young's modulus (i.e., graphene and multiwalled carbon nanotubes) and Cassie-Baxter design and used for oil and water separation. Proper selection of dispersed phase materials can enhance the stiffness of nanocomposite fiber membranes while their length has to be larger than their critical length. Chemical modification of the dispersed phase materials with fluorochemcials and their induced roughness were critical to achieve superhydrophobocity. Surface analytic tools including goniometer, X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR) spectroscopy, Raman spectroscopy, atomic force microscopy (AFM) and scanning electron microscope (SEM) were applied to characterize the superhydrophobic nanocomposite membranes. An AFM-based nanoindentation technique was used to measure quantitativly the stiffness of the nanocomposite membranes for local region and whole composites, compared with the results by a tensile test technique. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) techniques were used to confirm composition and formation of nanocomposite membranes. These membranes demonstrated excellent oil/water separation. This work has potential application in the field of water purification and remediation.

Absorption behavior of polycarboxylate superplasticizer with different molecular structures on montmorillonite.

Polycarboxylate (PCE) is a high performance superplasticizer for modern concrete. With the high quality sand becoming precious, more and more low quality sands are used in concrete. However, low quality sands generally contain a relatively high content of montmorillonite (MMT), which could seriously reduce the efficiency of PCE. In order to develop PCE suitable for concrete with low quality sands, the absorption behavior on MMT of PCE with different side chains and acid/ether ratio was investigated. In order to explore the effect of MMT on PCE, two macromonomers were selected, isoprene glycol ether 400(TPEG400) and isoprene glycol ether 2400 (TPEG2400), to synthesize six long and short side chain comb-type PCEs with acid-ether ratios of 1.5:1, 2.5:1 and 3.5:1, respectively. The MMT tolerance mechanism of comb-type PCE in MMT-containing cement slurry was examined by FT-IR, DLS, TOC and other analysis. The PCE with long side chain is much easier to be inserted into the layered structure of MMT, resulting in intercalation absorption. The absorption amount of two kinds of side chain PCE on the MMT particles decreased as the acid ether ratio increases. PCE with long side chains showed shear-thickening properties in MMT-containing cement slurry, on the contrary, short side chains showed shear-thinning properties.

Electrochemical aptasensor based on gold nanoparticle decorated Ti3C2Tx nanocomposites for chloramphenicol detection.

Using gold (Au) nanoparticle decorated Ti3C2Tx (Ti3C2Tx-Au) nanocomposites, a highly sensitive electrochemical aptasensor for the effective detection of chloramphenicol has been developed. As a two-dimensional layered material, the prepared composite not only provides high surface area, good conductivity, and thermal stability but also substantial binding sites for aptamers with high sensitivity and selectivity for the accurate determination of chloramphenicol. Interestingly, the conductivity and active sites were enhanced by freeze-drying Ti3C2Tx and in situ formation of Ti3C2Tx-Au nanocomposite. The fabricated aptasensor exhibited a very low detection limit (S/N ≥ 3) of 13.18 fg mL-1 with a linear range of 1 ~ 700 pg mL-1 and correlation coefficient of 0.9992. The fabricated aptasensor demonstrated an excellent reproducibility, repeatability, long-term stability, and high selectivity toward chloramphenicol. Further, the aptasensor was applied to real milk samples, and the recoveries were ranged from 98.93 to 101.93%.

Waterwheel-inspired high-performance hybrid electromagnetic-triboelectric nanogenerators based on fluid pipeline energy harvesting for power supply systems and data monitoring.

In this work, a self-powered system based on a triboelectric-electromagnetic hybrid pipeline energy harvesting module is demonstrated. Rabbit fur and poly tetra fluoroethylene (PTFE) are used as triboelectric electrodes to fabricate disk-type soft-contact triboelectric nanogenerators (TENGs) instead of traditional direct-contact TENGs to collect the mechanical energy of water flow and convert it into electrical energy. This design has a stable electrical output and gives an improved durability. Its simple fabrication process enables excellent potential for practical applications in industry. In addition, the hybridization of electromagnetic generator module and TENGs module to form a triboelectric-electromagnetic hybrid nanogenerator (TEHNG) can improve the electrical output performance, especially the current output. TEHNG cannot only power small electronic devices, such as lighting systems, but also collect independent fluid energy and monitor data signals simultaneously in harsh environments, such as fluid energy harvesting in industrial production pipelines and temperature and humidity in fluid environments. This work provides an efficient strategy to harvest multiple energies simultaneously, significantly increasing the yield and promoting the application of TENGs in engineering.

Modified low-temperature synthesis of graphene oxide nanosheets: Enhanced adsorption, antibacterial and antioxidant properties.

Herein, we report a simple, low-temperature, ecofriendly synthesis of graphene oxide nanosheets (GONs). Graphite powder was treated with KMnO4 and a concentrated H2SO4/H3PO4 mixture to synthesize GONs. The effects of various reaction conditions such as reaction time, temperature, amounts of cleaving agents (H2SO4/H3PO4), and oxidant (KMnO4) were investigated. The synthesized GONs were examined by various techniques in order to investigate their characteristics. The best results of the synthesized GONs were observed at 35 °C within 10 h of reaction time having 8:2 ratios of H2SO4/H3PO4 acid mixture. The main absorption peak in the UV-vis spectra of GONs was at 258 nm, which is due to the π-π* transition of the atomic CC bonds. The existence of stretching vibrations of C꞊O, O-H, C-H, and C-O in the Fourier transform infrared (FTIR) spectra verified the formation of GONs. Presence of a sharp peak at 2θ = 10° with an interlayer spacing distance of 0.88 nm in the observed XRD pattern revealed that the synthesized GONs were totally oxidized and that the interlayer spacing increased. The morphological investigations confirmed the formation of ultrathin, transparent, curly, and homogenous GONs. The synthesized GONs were applied as an adsorbent for the rapid uptake of four different pesticides viz.; Profenofos, Ethion, Cypermethrin, Thiamethoxam (TMX) from the pesticides spiked water samples. About 86% adsorption of Profenofos + Cypermethrin, and 50% adsorption of ethion and thiamethoxam took place within 20 min in presence of 10 mg GONs. In addition to this, the prepared GONs were tested for the antibacterial activity against four bacterial strains by agar well diffusion method. The synthesized GONs provide a significant inhibition for gram -positive (Bacillus subtilis, and Staphylococcus aureus) and gram-negative (Escherichia coli and Pseudomonas aeruginosa) bacterial strains. Moreover, the radical scavenging activities (RSA) of GONs were also checked and compared with Gallic acid as a standard. The obtained RSA of GONs was 60% in comparison to the 80% as of the standard Gallic acid at 1000 µg/mL concentration.

In-vitro cytotoxicity of nickel oxide nanoparticles against L-6 cell-lines: MMP, MTT and ROS studies.

In the present work we synthesize nickel oxide nanoparticles (NiO NPs) using Rhododendron arboretum (flower) (RNi), Tinospora cordifolia (stems) (GNi), Corylus jacquemontii (seeds) (CNi), and Nardostachys jatamansi (roots) (NNi) extracts by co-precipitation method. The synthesized NiO NPs were characterized in detail in terms of their morphological, crystalline nature, structural and antiproliferative activity against rat skeletal myoblast (L-6) cell lines. Morphological studies confirmed the formation of nanoparticles, while the structural and compositional characterization revealed the well-crystallinity and high purity of the synthesized nanoparticles. For biological applications and cytotoxicity examinations of the synthesized NPs, the rat skeletal myoblast (L-6) cell lines were subjected to study. By detailed cytotoxic investigations, it was observed that among the four kinds of NiO NPs prepared through different plant extracts, the Tinospora cordifolia (stems) showed strong antiproliferative activity against rat skeletal myoblast (L-6) cell lines and the calculated IC50 was 1.671 mg/mL. The observed antiproliferative activity towards different NiO NPs were in the order of GNi > NNi > RNi > CNi. The present studies demonstrate that simply synthesized NiO can efficiently be used as antiproliferative agents.

High-sensitive ferrocene labeled aptasensor for the detection of Mucin 1 by tuning the sequence constitution of complementary probe.

A strand displacement-based "signal-off" electrochemical aptasensor is reported for the detection of Mucin 1 (MUC 1) based on a high original signal. Different from the conventional "signal-off" electrochemical biosensors where electrochemical substances are dispersed in electrolyte solution, here the current signal was generated by the complementary probe (CP) associated with ferrocene (Fc) labeled aptamer (Apt.-Fc). Because Apt.-Fc and MUC 1 have a higher affinity, Apt.-Fc dissociates from CP in the presence of MUC 1, resulting in a reduction of detection current signal generated by oxidation of labeled Fc. In this system, high detection signal is necessary to improve the sensor's performance. For this aim, a strategy is proposed for changing the modalities of electron transport and the quantity of Apt.-Fc introduced by simply tuning the sequence constitution of CP. As expected, a high detection current signal was obtained after selecting CP(Apt.-Fc)-TTT as the optimal CP. The aptasensor was then employed to detect MUC 1, and satisfactory detection results with a low detection limit (LOD) of 0.087 pM (S/N = 3), good specificity, good stability, and feasibility of detection of MUC 1 in artificial serum (recovery of 92-101%, RSD of 1.36-5.23%) were obtained.

Tetracyanonickelate (II)/KOH/reduced graphene oxide fabricated carbon felt for mediated electron transfer type electrochemical sensor for efficient detection of N2O gas at room temperature.

N2O is the most significant anthropogenic greenhouse gas, which cause the ozone depletion. Hence, the room temperature detection of N2O is highly desirable. In this work, The TCN(II)-KOH-rGO/CF modified electrode was successfully fabricated by drop coating method. The synthesized electrode was successfully characterized by SEM, TEM, FT-IR and XRD. The sensor electrode was used to detect different N2O concentration in flow conditions at room temperature. TCN(II)-KOH-rGO/CF modified electrode showed high sensitivity towards N2O, a wide range from 1ppm to 16 ppm and low detection of 1 ppm N2O were achieved for the TCN(II)-KOH-rGO/CF modified electrode. The limit of detection and the response towards this nitrogen oxide is competitive to other sensing methods. In addition, the sensitivity of the electrochemical sensor electrode was compared with the online Gas Chromatography. Additionally, the selectivity of the working electrode was analyzed and specified. The working electrode stability was analyzed for more than 30 days shows good stability. The fabricated TCN(II)-KOH-rGO/CF electrode is easier to prepare to get excellent analytical performance towards N2O. Hence, the proposed TCN(II)-KOH-rGO/CF electrode could be the suitable material for detection of N2O in the real site process.

Direct sunlight-driven enhanced photocatalytic performance of V2O5 nanorods/ graphene oxide nanocomposites for the degradation of Victoria blue dye.

Herein, we report the synthesis and characterizations of Vanadium pentoxide (V2O5) nanorods/graphene oxide (GO) nanocomposite as efficient direct solar light driven photocatalyst for the enhanced degradation of victoria blue (VB) dye. The nanocomposite was synthesized by sonochemical process and characterized using several analytical methods in order to study the structural, morphological, compositional, optical and photocatalytic properties. The X-ray diffraction studies confirmed the orthorhombic structure of V2O5 while the morphological examinations revealed the growth of V2O5 nanorods and 2D GO sheets. Interestingly, the UV studies ratify that the bandgap of the nanocomposite was reduced compared to pure GO and V2O5. Interestingly, the interaction of the V2O5 nanorods with the graphene oxide substrate and its effect on the electronic properties of the combined system, have been examined by means of theoretical calculations, based on the so called Geometry, Frequency, Noncovalent, eXtended Tight Binding (GFN-xTB) method. Studying the photocatalytic behavior of nanocomposite, we observe an almost complete degradation (97.95%) of Victoria Blue (VB) dye under direct sunlight illumination within just 90 min. The outstanding nanocomposite photocatalytic efficiency was due to the excellent transfer of interfacial charge and the suppressed recombination of charge-carrier. The kinetics of the degradation process was also analyzed by calculating the rate constant and half-life time. Finally, a possible mechanism has also been discussed for the degradation process of VB dye using nanocomposite under direct sunlight irradiation.

Synthesis of porous 2D layered nickel oxide-reduced graphene oxide (NiO-rGO) hybrid composite for the efficient electrochemical detection of epinephrine in biological fluid.

In the present research work, 2D-Porous NiO decorated graphene nanocomposite was synthesized by hydrothermal method to monitored the concentration of epinephrine (EPI). The morphology (SEM and TEM) results confirmed 2D-Porous NiO nanoparticles firmly attached over graphene nanosheets. FTIR and XPS analysis confirmed the formation of nickel oxide formation and complete reduction of GO to rGO. The electrochemical activity of the proposed NiO-rGO/GCE modified electrode on epinephrine was analyzed by simple cyclic voltammetry technique. The proposed low cost NiO-rGO/GCE modified electrode showed excellent catalytic activity over GCE and rGO/GCE electrodes. Due to its high conductivity and charge transfer ability of the NiO-rGO/GCE modified electrode exhibited high sensitivity of EPI at optimized conditions. The anodic peak current of the EPI linearly increases with increasing the concertation of EPI. A wide linear range (50 µM-1000 µM) was achieved with high correlation coefficient (R2 = 0.9986) and the limit of detection (LOD) of NiO-rGO/GCE modified electrode was calculated to be 10 µM. NiO-rGO/GCE electrode showed good stability and repeatability towards the EPI oxidation. Mainly, the proposed NiO-rGO/GCE modified electrode showed good sensitivity of EPI in the human biological fluid with high recovery percentage. The low cost, NiO-rGO/GCE electrode could be the promising sensor electrode for the detection of Epinephrine in the real samples.

CdO-ZnO nanorices for enhanced and selective formaldehyde gas sensing applications.

This paper reports synthesis, properties and gas sensing applications of ZnO nanoflowers and CdO-ZnO nanorices prepared by hydrothermal process. The morphological characterizations confirmed the formation of well-defined nanoflowers and nanorices structures for ZnO and CdO-ZnO nanomaterials, respectively. The structural properties revealed the wurtzite hexagonal phase of the synthesized materials. The sensor devices based on ZnO nanoflowers and CdO-ZnO nanorices were fabricated and tested towards various gases including ethanol, methanol, ammonia, carbon monoxide, methane and formaldehyde. The fabricated gas sensor based on CdO-ZnO nanorices exhibited a high response (34.5) towards 300 ppm formaldehyde gas at 350 °C compared to ZnO nanoflowers (14.5) under the same experimental conditions. The response and recovery times for ZnO nanoflowers-based sensor were~9.8 s and ~6 s while for CdO-ZnO based sensor, these were ~10s and ~6s, respectively. A rapid response (34.5) for CdO-ZnO nanorices based formaldehyde gas sensor was observed as compared to other gases such as ammonia (12.3), methanol (16.5), ethanol (20), carbon monoxide (16.3) and methane (12.4), which confirm the high-selectivity towards formaldehyde gas. Finally, a plausible formaldehyde gas sensing mechanism is proposed.

Highly Sensitive and Selective Eco-Toxic 4-Nitrophenol Chemical Sensor Based on Ag-Doped ZnO Nanoflowers Decorated with Nanosheets.

Herein, we have developed a novel sensing electrode to detect the eco-toxic 4-nitrophenol (4-NP). Ag-doped-ZnO nanoflowers were synthesized by facile hydrothermal method and examined by several characterization techniques in order to understand the morphology, crystal structure, composition, and surface properties. Morphological results were confirmed by the formation of Ag-doped ZnO nanoflowers decorated with nanosheets. Ag-doped ZnO/glassy carbon electrode (GCE) electrode-material-matrix was used for electrochemical sensing of toxic 4-NP. Under optimized conditions, Ag-doped ZnO/GCE modified electrode exhibits high-sensitivity and selectivity compared to the bare GCE electrode. The Ag-doped ZnO/GCE modified electrode exhibits high electrocatalytic oxidation towards 4-NP. Anodic peak current of 4-NP is increased linearly by increasing the concentration of nitrophenol. Additionally, Ag-doped ZnO/GCE shows a wide range of sensitivity from 10 µM to 500 µM, and a linear calibration plot with a good detection limit of 3 µM (S/N = 3). The proposed Ag-doped ZnO/GCE modified electrode showed high sensing stability. In addition, the oxidation mechanism was studied. The obtained results revealed that the Ag-ZnO/GCE electrode could be the promising sensing electrode for 4-NP sensing.

Unveiling the potential of PANI@MnO2@rGO ternary nanocomposite in energy storage and gas sensing.

The development of advanced materials for energy storage and gas sensing applications has gained significant attention in recent years. In this study, we synthesized and characterized PANI@MnO2@rGO ternary nanocomposites (NCs) to explore their potential in supercapacitors and gas sensing devices. The ternary NCs were synthesized through a multi-step process involving the hydrothermal synthesis of MnO2 nanoparticles, preparation of PANI@rGO composites and the assembly to the ternary PANI@MnO2@rGO ternary NCs. The structural, morphological, and compositional characteristics of the materials were thoroughly analyzed using techniques such as XRD, FESEM, TEM, FTIR, and Raman spectroscopy. In the realm of gas sensing, the ternary NCs exhibited excellent performance as NH3 gas sensors. The optimized operating temperature of 100 °C yielded a peak response of 15.56 towards 50 ppm NH3. The nanocomposites demonstrated fast response and recovery times of 6 s and 10 s, respectively, and displayed remarkable selectivity for NH3 gas over other tested gases. For supercapacitor applications, the electrochemical performance of the ternary NCs was evaluated using cyclic voltammetry and galvanostatic charge-discharge techniques. The composites exhibited pseudocapacitive behavior, with the capacitance reaching up to 185 F/g at 1 A/g and excellent capacitance retention of approximately 88.54% over 4000 charge-discharge cycles. The unique combination of rGO, PANI, and MnO2 nanoparticles in these ternary NCs offer synergistic advantages, showcasing their potential to address challenges in energy storage and gas sensing technologies.

Phyllostachys nigra (Lodd. ex Lindl.) derived polysaccharide with enhanced glycolipid metabolism regulation and mice gut microbiome.

This study focuses on the characterization and regulation of glycolipid metabolism of polysaccharides derived from biomass of Phyllostachys nigra (Lodd. ex Lindl.) root (PNr). The extracts from dilute hydrochloric acid, hot water, and 2 % sodium hydroxide solution were characterized through molecular weight, gel permeation chromatography, monosaccharides, Fourier transform infrared, and nuclear magnetic resonance spectroscopy analyses. Polysaccharide from alkali extraction and molecular sieve purification (named as: PNS2A) exhibited optimal inhibitory of 3T3-L1 cellular differentiation and lowered insulin resistance. The PNS2A is made of a hemicellulose-like main chain of →4)-ß-D-Xylp-(1→ that was connected by branches of 4-O-Me-α-GlcAp-(1→, T-α-D-Galp-(1→, T-α-L-Araf-(1→, →2)-α-L-Araf-(1→, as well as ß-D-Glcp-(1→4-ß-D-Glcp-(1→ fragments. Oral delivery of PNS2A in diabetes mice brought down blood glucose and cholesterol levels and regulated glucose and lipid metabolism. PNS2A alleviated diabetes symptoms and body weight and protected liver and kidney function in model animals by altering the gut microbiome. Polysaccharides can be a new approach to develop bamboo resources.

Highly fluorescent nickel based metal organic framework for enhanced sensing of Fe3+ and Cr2O72- ions.

Heavy metal contamination has sparked widespread concern among the populace. The significant issues necessitate the creation of high-performance fluorescent pigments that can identify harmful elements in water. The present study deals with metal organic framework [MOF] based on nickel [Ni-BDC MOF]. The Ni-BDC MOF was prepared by facile solvothermal method using nickel nitrate hexahydrate and terephthalic acid ligand as precursors. The MOF was characterized by various techniques in order to examine the crystal, morphological, structural, composition, thermal and optical properties. The detailed characterizations revealed that the synthesized Ni-BDC MOF are well-crystalline with high purity and possessing 3D rhombohedral microcrystals with rough surface. The MOF demonstrate good luminescence performance and excellent water stability. According to the Stern Volmer plot, the tests set up under optimized conditions demonstrate a linear correlation between the fluorescence intensity and concentration of both ions, i.e. Fe3+, and Cr2O72- ions. The linear range and detection limit for Fe3+ and Cr2O72- were found to be 0-1.4 nM and 0.159 nM, and 0-1 nM and 0.120 nM, respectively. The mechanisms for the selective detection of cations and anions were also explored. The recyclability for the prepared MOF was checked up to five cycles which showed excellent stability with just a slight reduction in efficiency. The constructed sensor was also used to assess the presence of Fe3+ and Cr2O72- ions in actual water samples. The results of the different experiments revealed that the prepared MOF is a good material for detecting Fe3+ and Cr2O72- ions.

Sodium alginate reinforced polyacrylamide/xanthan gum double network ionic hydrogels for stress sensing and self-powered wearable device applications.

Strong and ductile sodium alginate (SA) reinforced polyacrylamide (PAM)/xanthan gum (XG) double network ionic hydrogels were constructed for stress sensing and self-powered wearable device applications. In the designed network of PXS-Mn+/LiCl (short for PAM/XG/SA-Mn+/LiCl, where Mn+ stands for Fe3+, Cu2+ or Zn2+), PAM acts as a flexible hydrophilic skeleton, and XG functions as a ductile second network. The macromolecule SA interacts with metal ion Mn+ to form a unique complex structure, significantly improving the mechanical strength of the hydrogel. The addition of inorganic salt LiCl endows the hydrogel with high electrical conductivity, and meanwhile reduces the freezing point and prevents water loss of the hydrogel. PXS-Mn+/LiCl exhibits excellent mechanical properties and ultra-high ductility (a fracture tensile strength up to 0.65 MPa and a fracture strain up to 1800%), and high stress-sensing performance (a high GF up to 4.56 and pressure sensitivity of 0.122). Moreover, a self-powered device with a dual-power-supply mode, i.e., PXS-Mn+/LiCl-based primary battery and TENG, and a capacitor as the energy storage component was constructed, which shows promising prospects for self-powered wearable electronics.

Initiating Binary Metal Oxides Microcubes Electrsomagnetic Wave Absorber Toward Ultrabroad Absorption Bandwidth Through Interfacial and Defects Modulation.

Cobalt nickel bimetallic oxides (NiCo2O4) have received numerous attentions in terms of their controllable morphology, high temperature, corrosion resistance and strong electromagnetic wave (EMW) absorption capability. However, broadening the absorption bandwidth is still a huge challenge for NiCo2O4-based absorbers. Herein, the unique NiCo2O4@C core-shell microcubes with hollow structures were fabricated via a facile sacrificial template strategy. The concentration of oxygen vacancies and morphologies of the three-dimensional (3D) cubic hollow core-shell NiCo2O4@C framework were effectively optimized by adjusting the calcination temperature. The specially designed 3D framework structure facilitated the multiple reflections of incident electromagnetic waves and provided rich interfaces between multiple components, generating significant interfacial polarization losses. Dipole polarizations induced by oxygen vacancies could further enhance the attenuation ability for the incident EM waves. The optimized NiCo2O4@C hollow microcubes exhibit superior EMW absorption capability with minimum RL (RLmin) of -84.45 dB at 8.4 GHz for the thickness of 3.0 mm. Moreover, ultrabroad effective absorption bandwidth (EAB) as large as 12.48 GHz (5.52-18 GHz) is obtained. This work is believed to illuminate the path to synthesis of high-performance cobalt nickel bimetallic oxides for EMW absorbers with excellent EMW absorption capability, especially in broadening effective absorption bandwidth.

MXene Enhanced 3D Needled Waste Denim Felt for High-Performance Flexible Supercapacitors.

MXene, a transition metal carbide/nitride, has been prominent as an ideal electrochemical active material for supercapacitors. However, the low MXene load limits its practical applications. As environmental concerns and sustainable development become more widely recognized, it is necessary to explore a greener and cleaner technology to recycle textile by-products such as cotton. The present study proposes an effective 3D fabrication method that uses MXene to fabricate waste denim felt into ultralight and flexible supercapacitors through needling and carbonization. The 3D structure provided more sites for loading MXene onto Z-directional fiber bundles, resulting in more efficient ion exchange between the electrolyte and electrodes. Furthermore, the carbonization process removed the specific adverse groups in MXenes, further improving the specific capacitance, energy density, power density and electrical conductivity of supercapacitors. The electrodes achieve a maximum specific capacitance of 1748.5 mF cm-2 and demonstrate remarkable cycling stability maintaining more than 94% after 15,000 galvanostatic charge/discharge cycles. Besides, the obtained supercapacitors present a maximum specific capacitance of 577.5 mF cm-2, energy density of 80.2 µWh cm-2 and power density of 3 mW cm-2, respectively. The resulting supercapacitors can be used to develop smart wearable power devices such as smartwatches, laying the foundation for a novel strategy of utilizing waste cotton in a high-quality manner.