An objective skill assessment framework for microsurgical anastomosis based on ALI scores.

INTRODUCTION: The current assessment and standardization of microsurgical skills are subjective, posing challenges in reliable skill evaluation. We aim to address these limitations by developing a quantitative and objective framework for accurately assessing and enhancing microsurgical anastomosis skills among surgical trainees. We hypothesize that this framework can differentiate the proficiency levels of microsurgeons, aligning with subjective assessments based on the ALI score. METHODS: We select relevant performance metrics from the literature on laparoscopic skill assessment and human motor control studies, focusing on time, instrument kinematics, and tactile information. This information is measured and estimated by a set of sensors, including cameras, a motion capture system, and tactile sensors. The recorded data is analyzed offline using our proposed evaluation framework. Our study involves 12 participants of different ages ([Formula: see text] years) and genders (nine males and three females), including six novice and six intermediate subjects, who perform surgical anastomosis procedures on a chicken leg model. RESULTS: We show that the proposed set of objective and quantitative metrics to assess skill proficiency aligns with subjective evaluations, particularly the ALI score method, and can effectively differentiate novices from more proficient microsurgeons. Furthermore, we find statistically significant disparities, where microsurgeons with intermediate level of skill proficiency surpassed novices in both task speed, reduced idle time, and smoother, briefer hand displacements. CONCLUSION: The framework enables accurate skill assessment and provides objective feedback for improving microsurgical anastomosis skills among surgical trainees. By overcoming the subjectivity and limitations of current assessment methods, our approach contributes to the advancement of surgical education and the development of aspiring microsurgeons. Furthermore, our framework emerges to precisely distinguish and classify proficiency levels (novice and intermediate) exhibited by microsurgeons.

Hand pose selection in a bimanual fine-manipulation task.

Many daily tasks involve the collaboration of both hands. Humans dexterously adjust hand poses and modulate the forces exerted by fingers in response to task demands. Hand pose selection has been intensively studied in unimanual tasks, but little work has investigated bimanual tasks. This work examines hand poses selection in a bimanual high-precision-screwing task taken from watchmaking. Twenty right-handed subjects dismounted a screw on the watch face with a screwdriver in two conditions. Results showed that although subjects used similar hand poses across steps within the same experimental conditions, the hand poses differed significantly in the two conditions. In the free-base condition, subjects needed to stabilize the watch face on the table. The role distribution across hands was strongly influenced by hand dominance: the dominant hand manipulated the tool, whereas the nondominant hand controlled the additional degrees of freedom that might impair performance. In contrast, in the fixed-base condition, the watch face was stationary. Subjects used both hands even though single hand would have been sufficient. Importantly, hand poses decoupled the control of task-demanded force and torque across hands through virtual fingers that grouped multiple fingers into functional units. This preference for bimanual over unimanual control strategy could be an effort to reduce variability caused by mechanical couplings and to alleviate intrinsic sensorimotor processing burdens. To afford analysis of this variety of observations, a novel graphical matrix-based representation of the distribution of hand pose combinations was developed. Atypical hand poses that are not documented in extant hand taxonomies are also included.NEW & NOTEWORTHY We study hand poses selection in bimanual fine motor skills. To understand how roles and control variables are distributed across the hands and fingers, we compared two conditions when unscrewing a screw from a watch face. When the watch face needed positioning, role distribution was strongly influenced by hand dominance; when the watch face was stationary, a variety of hand pose combinations emerged. Control of independent task demands is distributed either across hands or across distinct groups of fingers.

An inverse optimization approach to understand human acquisition of kinematic coordination in bimanual fine manipulation tasks.

Tasks that require the cooperation of both hands and arms are common in human everyday life. Coordination helps to synchronize in space and temporally motion of the upper limbs. In fine bimanual tasks, coordination enables also to achieve higher degrees of precision that could be obtained from a single hand. We studied the acquisition of bimanual fine manipulation skills in watchmaking tasks, which require assembly of pieces at millimeter scale. It demands years of training. We contrasted motion kinematics performed by novice apprentices to those of professionals. Fifteen subjects, ten novices and five experts, participated in the study. We recorded force applied on the watch face and kinematics of fingers and arms. Results indicate that expert subjects wisely place their fingers on the tools to achieve higher dexterity. Compared to novices, experts also tend to align task-demanded force application with the optimal force transmission direction of the dominant arm. To understand the cognitive processes underpinning the different coordination patterns across experts and novice subjects, we followed the optimal control theoretical framework and hypothesize that the difference in task performances is caused by changes in the central nervous system's optimal criteria. We formulated kinematic metrics to evaluate the coordination patterns and exploit inverse optimization approach to infer the optimal criteria. We interpret the human acquisition of novel coordination patterns as an alteration in the composition structure of the central nervous system's optimal criteria accompanied by the learning process.

Decoding the grasping intention from electromyography during reaching motions.

BACKGROUND: Active upper-limb prostheses are used to restore important hand functionalities, such as grasping. In conventional approaches, a pattern recognition system is trained over a number of static grasping gestures. However, training a classifier in a static position results in lower classification accuracy when performing dynamic motions, such as reach-to-grasp. We propose an electromyography-based learning approach that decodes the grasping intention during the reaching motion, leading to a faster and more natural response of the prosthesis. METHODS AND RESULTS: Eight able-bodied subjects and four individuals with transradial amputation gave informed consent and participated in our study. All the subjects performed reach-to-grasp motions for five grasp types, while the elecromyographic (EMG) activity and the extension of the arm were recorded. We separated the reach-to-grasp motion into three phases, with respect to the extension of the arm. A multivariate analysis of variance (MANOVA) on the muscular activity revealed significant differences among the motion phases. Additionally, we examined the classification performance on these phases. We compared the performance of three different pattern recognition methods; Linear Discriminant Analysis (LDA), Support Vector Machines (SVM) with linear and non-linear kernels, and an Echo State Network (ESN) approach. Our off-line analysis shows that it is possible to have high classification performance above 80% before the end of the motion when with three-grasp types. An on-line evaluation with an upper-limb prosthesis shows that the inclusion of the reaching motion in the training of the classifier importantly improves classification accuracy and enables the detection of grasp intention early in the reaching motion. CONCLUSIONS: This method offers a more natural and intuitive control of prosthetic devices, as it will enable controlling grasp closure in synergy with the reaching motion. This work contributes to the decrease of delays between the user's intention and the device response and improves the coordination of the device with the motion of the arm.

Triggering social interactions: chimpanzees respond to imitation by a humanoid robot and request responses from it.

Even the most rudimentary social cues may evoke affiliative responses in humans and promote social communication and cohesion. The present work tested whether such cues of an agent may also promote communicative interactions in a nonhuman primate species, by examining interaction-promoting behaviours in chimpanzees. Here, chimpanzees were tested during interactions with an interactive humanoid robot, which showed simple bodily movements and sent out calls. The results revealed that chimpanzees exhibited two types of interaction-promoting behaviours during relaxed or playful contexts. First, the chimpanzees showed prolonged active interest when they were imitated by the robot. Second, the subjects requested 'social' responses from the robot, i.e. by showing play invitations and offering toys or other objects. This study thus provides evidence that even rudimentary cues of a robotic agent may promote social interactions in chimpanzees, like in humans. Such simple and frequent social interactions most likely provided a foundation for sophisticated forms of affiliative communication to emerge.

Learning robotic eye-arm-hand coordination from human demonstration: a coupled dynamical systems approach.

We investigate the role of obstacle avoidance in visually guided reaching and grasping movements. We report on a human study in which subjects performed prehensile motion with obstacle avoidance where the position of the obstacle was systematically varied across trials. These experiments suggest that reaching with obstacle avoidance is organized in a sequential manner, where the obstacle acts as an intermediary target. Furthermore, we demonstrate that the notion of workspace travelled by the hand is embedded explicitly in a forward planning scheme, which is actively involved in detecting obstacles on the way when performing reaching. We find that the gaze proactively coordinates the pattern of eye-arm motion during obstacle avoidance. This study provides also a quantitative assessment of the coupling between the eye-arm-hand motion. We show that the coupling follows regular phase dependencies and is unaltered during obstacle avoidance. These observations provide a basis for the design of a computational model. Our controller extends the coupled dynamical systems framework and provides fast and synchronous control of the eyes, the arm and the hand within a single and compact framework, mimicking similar control system found in humans. We validate our model for visuomotor control of a humanoid robot.

RoBétArmé Project: Human-robot collaborative construction system for shotcrete digitization and automation through advanced perception, cognition, mobility and additive manufacturing skills.

The importance of construction automation has grown worldwide, aiming to deliver new machineries for the automation of roads, tunnels, bridges, buildings and earth-work construction. This need is mainly driven by (i) the shortage and rising costs of skilled workers, (ii) the tremendous increased needs for new infrastructures to serve the daily activities and (iii) the immense demand for maintenance of ageing infrastructure. Shotcrete (sprayed concrete) is increasingly becoming popular technology among contractors and builders, as its application is extremely economical and flexible as the growth in construction repairs in developed countries demand excessive automation of concrete placement. Even if shotcrete technology is heavily mechanized, the actual application is still performed manually at a large extend. RoBétArméEuropean project targets the Construction 4.0 transformation of the construction with shotcrete with the adoption of breakthrough technologies such as sensors, augmented reality systems, high-performance computing, additive manufacturing, advanced materials, autonomous robots and simulation systems, technologies that have already been studied and applied so far in Industry 4.0. The paper at hand showcases the development of a novel robotic system with advanced perception, cognition and digitization capabilities for the automation of all phases of shotcrete application. In particular, the challenges and barriers in shotcrete automation are presented and the RoBétArmésuggested solutions are outlined. We introduce a basic conceptual architecture of the system to be developed and we demonstrate the four application scenarios on which the system is designated to operate.

The RoBétArmé European project targets the Construction 4.0 transformation of the construction with shotcrete with the adoption of breakthrough technologies such as sensors, augmented reality systems, high-performance computing, additive manufacturing, advanced materials, autonomous robots and simulation systems, technologies that have already been studied and applied so far in Industry 4.0. This paper showcases a case study on which novel robotic systems will be developed for the automation of shotecrete application. The outcomes of this research can be widely used in other application technologies related to the construction domain.

Inferring individual evaluation criteria for reaching trajectories with obstacle avoidance from EEG signals.

During reaching actions, the human central nerve system (CNS) generates the trajectories that optimize effort and time. When there is an obstacle in the path, we make sure that our arm passes the obstacle with a sufficient margin. This comfort margin varies between individuals. When passing a fragile object, risk-averse individuals may adopt a larger margin by following the longer path than risk-prone people do. However, it is not known whether this variation is associated with a personalized cost function used for the individual optimal control policies and how it is represented in our brain activity. This study investigates whether such individual variations in evaluation criteria during reaching results from differentiated weighting given to energy minimization versus comfort, and monitors brain error-related potentials (ErrPs) evoked when subjects observe a robot moving dangerously close to a fragile object. Seventeen healthy participants monitored a robot performing safe, daring and unsafe trajectories around a wine glass. Each participant displayed distinct evaluation criteria on the energy efficiency and comfort of robot trajectories. The ErrP-BCI outputs successfully inferred such individual variation. This study suggests that ErrPs could be used in conjunction with an optimal control approach to identify the personalized cost used by CNS. It further opens new avenues for the use of brain-evoked potential to train assistive robotic devices through the use of neuroprosthetic interfaces.

Crash test-based assessment of injury risks for adults and children when colliding with personal mobility devices and service robots.

Autonomous mobility devices such as transport, cleaning, and delivery robots, hold a massive economic and social benefit. However, their deployment should not endanger bystanders, particularly vulnerable populations such as children and older adults who are inherently smaller and fragile. This study compared the risks faced by different pedestrian categories and determined risks through crash testing involving a service robot hitting an adult and a child dummy. Results of collisions at 3.1 m/s (11.1 km/h/6.9 mph) showed risks of serious head (14%), neck (20%), and chest (50%) injuries in children, and tibia fracture (33%) in adults. Furthermore, secondary impact analysis resulted in both populations at risk of severe head injuries, namely, from falling to the ground. Our data and simulations show mitigation strategies for reducing impact injury risks below 5% by either lowering the differential speed at impact below 1.5 m/s (5.4 km/h/3.3 mph) or through the usage of absorbent materials. The results presented herein may influence the design of controllers, sensing awareness, and assessment methods for robots and small vehicles standardization, as well as, policymaking and regulations for the speed, design, and usage of these devices in populated areas.

EMG-driven shared human-robot compliant control for in-hand object manipulation in hand prostheses.

Objective. The limited functionality of hand prostheses remains one of the main reasons behind the lack of its wide adoption by amputees. Indeed, while commercial prostheses can perform a reasonable number of grasps, they are often inadequate for manipulating the object once in hand. This lack of dexterity drastically restricts the utility of prosthetic hands. We aim at investigating a novel shared control strategy that combines autonomous control of forces exerted by a robotic hand with electromyographic (EMG) decoding to perform robust in-hand object manipulation.Approach. We conduct a three-day long longitudinal study with eight healthy subjects controlling a 16-degrees-of-freedom robotic hand to insert objects in boxes of various orientations. EMG decoding from forearm muscles enables subjects to move, proportionally and simultaneously, the fingers of the robotic hand. The desired object rotation is inferred using two EMG electrodes placed on the shoulder that record the activity of muscles responsible for elevation and depression. During the object interaction phase, the autonomous controller stabilizes and rotates the object to achieve the desired pose. In this study, we compare an incremental and a proportional shoulder-decoding method in combination with two state machine interfaces offering different levels of assistance.Main results. Results indicate that robotic assistance reduces the number of failures by41%and, when combined with an incremental shoulder EMG decoding, leads to faster task completion time (median = 16.9 s), compared to other control conditions. Training to use the assistive device is fast. After one session of practice, all subjects managed to achieve tasks with50%less failures.Significance. Shared control approaches that give some authority to an autonomous controller on-board the prosthesis are an alternative to control schemes relying on EMG decoding alone. This may improve the dexterity and versatility of robotic prosthetic hands for people with trans-radial amputation. By delegating control of forces to the prosthesis' on-board control, one speeds up reaction time and improves the precision of force control. Such a shared control mechanism may enable amputees to perform fine insertion tasks solely using their prosthetic hands. This may restore some of the functionality of the disabled arm.

The Gaze Dialogue Model: Nonverbal Communication in HHI and HRI.

When humans interact with each other, eye gaze movements have to support motor control as well as communication. On the one hand, we need to fixate the task goal to retrieve visual information required for safe and precise action-execution. On the other hand, gaze movements fulfil the purpose of communication, both for reading the intention of our interaction partners, as well as to signal our action intentions to others. We study this Gaze Dialogue between two participants working on a collaborative task involving two types of actions: 1) individual action and 2) action-in-interaction. We recorded the eye-gaze data of both participants during the interaction sessions in order to build a computational model, the Gaze Dialogue, encoding the interplay of the eye movements during the dyadic interaction. The model also captures the correlation between the different gaze fixation points and the nature of the action. This knowledge is used to infer the type of action performed by an individual. We validated the model against the recorded eye-gaze behavior of one subject, taking the eye-gaze behavior of the other subject as the input. Finally, we used the model to design a humanoid robot controller that provides interpersonal gaze coordination in human-robot interaction scenarios. During the interaction, the robot is able to: 1) adequately infer the human action from gaze cues; 2) adjust its gaze fixation according to the human eye-gaze behavior; and 3) signal nonverbal cues that correlate with the robot's own action intentions.

Customizing skills for assistive robotic manipulators, an inverse reinforcement learning approach with error-related potentials.

Robotic assistance via motorized robotic arm manipulators can be of valuable assistance to individuals with upper-limb motor disabilities. Brain-computer interfaces (BCI) offer an intuitive means to control such assistive robotic manipulators. However, BCI performance may vary due to the non-stationary nature of the electroencephalogram (EEG) signals. It, hence, cannot be used safely for controlling tasks where errors may be detrimental to the user. Avoiding obstacles is one such task. As there exist many techniques to avoid obstacles in robotics, we propose to give the control to the robot to avoid obstacles and to leave to the user the choice of the robot behavior to do so a matter of personal preference as some users may be more daring while others more careful. We enable the users to train the robot controller to adapt its way to approach obstacles relying on BCI that detects error-related potentials (ErrP), indicative of the user's error expectation of the robot's current strategy to meet their preferences. Gaussian process-based inverse reinforcement learning, in combination with the ErrP-BCI, infers the user's preference and updates the obstacle avoidance controller so as to generate personalized robot trajectories. We validate the approach in experiments with thirteen able-bodied subjects using a robotic arm that picks up, places and avoids real-life objects. Results show that the algorithm can learn user's preference and adapt the robot behavior rapidly using less than five demonstrations not necessarily optimal.

Hand-Object Interaction: From Human Demonstrations to Robot Manipulation.

Human-object interaction is of great relevance for robots to operate in human environments. However, state-of-the-art robotic hands are far from replicating humans skills. It is, therefore, essential to study how humans use their hands to develop similar robotic capabilities. This article presents a deep dive into hand-object interaction and human demonstrations, highlighting the main challenges in this research area and suggesting desirable future developments. To this extent, the article presents a general definition of the hand-object interaction problem together with a concise review for each of the main subproblems involved, namely: sensing, perception, and learning. Furthermore, the article discusses the interplay between these subproblems and describes how their interaction in learning from demonstration contributes to the success of robot manipulation. In this way, the article provides a broad overview of the interdisciplinary approaches necessary for a robotic system to learn new manipulation skills by observing human behavior in the real world.

Intent Prediction Based on Biomechanical Coordination of EMG and Vision-Filtered Gaze for End-Point Control of an Arm Prosthesis.

We propose a novel controller for powered prosthetic arms, where fused EMG and gaze data predict the desired end-point for a full arm prosthesis, which could drive the forward motion of individual joints. We recorded EMG, gaze, and motion-tracking during pick-and-place trials with 7 able-bodied subjects. Subjects positioned an object above a random target on a virtual interface, each completing around 600 trials. On average across all trials and subjects gaze preceded EMG and followed a repeatable pattern that allowed for prediction. A computer vision algorithm was used to extract the initial and target fixations and estimate the target position in 2D space. Two SVRs were trained with EMG data to predict the x- and y- position of the hand; results showed that the y-estimate was significantly better than the x-estimate. The EMG and gaze predictions were fused using a Kalman Filter-based approach, and the positional error from using EMG-only was significantly higher than the fusion of EMG and gaze. The final target position Root Mean Squared Error (RMSE) decreased from 9.28 cm with an EMG-only prediction to 6.94 cm when using a gaze-EMG fusion. This error also increased significantly when removing some or all arm muscle signals. However, using fused EMG and gaze, there were no significant difference between predictors that included all muscles, or only a subset of muscles.

Movement curvature planning through force field internal models.

Human motion studies have focused primarily on modeling straight point-to-point reaching movements. However, many goal-directed reaching movements, such as movements directed towards oneself, are not straight but rather follow highly curved trajectories. These movements are particularly interesting to study since they are essential in our everyday life, appear early in development and are routinely used to assess movement deficits following brain lesions. We argue that curved and straight-line reaching movements are generated by a unique neural controller and that the observed curvature of the movement is the result of an active control strategy that follows the geometry of one's body, for instance to avoid trajectories that would hit the body or yield postures close to the joint limits. We present a mathematical model that accounts for such an active control strategy and show that the model reproduces with high accuracy the kinematic features of human data during unconstrained reaching movements directed toward the head. The model consists of a nonlinear dynamical system with a single stable attractor at the target. Embodiment-related task constraints are expressed as a force field that acts on the dynamical system. Finally, we discuss the biological plausibility and neural correlates of the model's parameters and suggest that embodiment should be considered as a main cause for movement trajectory curvature.

Trends and challenges in robot manipulation.

Dexterous manipulation is one of the primary goals in robotics. Robots with this capability could sort and package objects, chop vegetables, and fold clothes. As robots come to work side by side with humans, they must also become human-aware. Over the past decade, research has made strides toward these goals. Progress has come from advances in visual and haptic perception and in mechanics in the form of soft actuators that offer a natural compliance. Most notably, immense progress in machine learning has been leveraged to encapsulate models of uncertainty and to support improvements in adaptive and robust control. Open questions remain in terms of how to enable robots to deal with the most unpredictable agent of all, the human.

Social babbling: The emergence of symbolic gestures and words.

Language acquisition theories classically distinguish passive language understanding from active language production. However, recent findings show that brain areas such as Broca's region are shared in language understanding and production. Furthermore, these areas are also implicated in understanding and producing goal-oriented actions. These observations question the passive view of language development. In this work, we propose a cognitive developmental model of symbol acquisition, coherent with an active view of language learning. For that purpose, we introduce the concept of social babbling. In this view, symbols are learned in the same way as goal-oriented actions in the context of specific caregiver-infant interactions. We show that this model allows a virtual agent to learn both symbolic words and gestures to refer to objects while interacting with a caregiver. We validate our model by reproducing results from studies on the influence of parental responsiveness on infants language acquisition.

Apraxia: a review.

Praxic functions are frequently altered following brain lesion, giving rise to apraxia - a complex pattern of impairments that is difficult to assess or interpret. In this chapter, we review the current taxonomies of apraxia and related cognitive and neuropsychological models. We also address the questions of the neuroanatomical correlates of apraxia, the relation between apraxia and aphasia and the analysis of apraxic errors. We provide a possible explanation for the difficulties encountered in investigating apraxia and also several approaches to overcome them, such as systematic investigation and modeling studies. Finally, we argue for a multidisciplinary approach. For example, apraxia should be studied in consideration with and could contribute to other fields such as normal motor control, neuroimaging and neurophysiology.

On learning, representing, and generalizing a task in a humanoid robot.

We present a programming-by-demonstration framework for generically extracting the relevant features of a given task and for addressing the problem of generalizing the acquired knowledge to different contexts. We validate the architecture through a series of experiments, in which a human demonstrator teaches a humanoid robot simple manipulatory tasks. A probability-based estimation of the relevance is suggested by first projecting the motion data onto a generic latent space using principal component analysis. The resulting signals are encoded using a mixture of Gaussian/Bernoulli distributions (Gaussian mixture model/Bernoulli mixture model). This provides a measure of the spatio-temporal correlations across the different modalities collected from the robot, which can be used to determine a metric of the imitation performance. The trajectories are then generalized using Gaussian mixture regression. Finally, we analytically compute the trajectory which optimizes the imitation metric and use this to generalize the skill to different contexts.

Building Robota, a mini-humanoid robot for the rehabilitation of children with autism.

The Robota project constructs a series of multiple-degrees-of-freedom, doll-shaped humanoid robots, whose physical features resemble those of a human baby. The Robota robots have been applied as assistive technologies in behavioral studies with low-functioning children with autism. These studies investigate the potential of using an imitator robot to assess children's imitation ability and to teach children simple coordinated behaviors. In this article, the authors review the recent technological developments that have made the Robota robots suitable for use with children with autism. They critically appraise the main outcomes of two sets of behavioral studies conducted with Robota and discuss how these results inform future development of the Robota robots and robots in general for the rehabilitation of children with complex developmental disabilities.