Effects of fluid composition in fluid injection experiments in porous media.

Experiments on fluid flow in porous media, using fluids loaded with solids of various grain sizes, have been conducted in a modified Hele-Shaw setup. This setup utilised weakly cemented porous media with specific hydraulic and mechanical properties. Fluid injection in coarse granular media with clean or low-concentration fine particles, results in infiltration only, with pressure close to the material tensile strength, while injection in finer granular material causes damage alongside infiltration, with the fluid pressure still close to the material tensile strength. When larger particle sizes or higher particle concentrations are used in the mixture, the fluid travels further within the porous medium, primarily influenced by the grain size of the granular medium. In the latter case, the Darcy flow equation with an effective permeability term can be employed to determine the pressure differential. For the largest particle sizes included in the fluid, the equation is still applicable, but the effective permeability requires adjustment for particle size within the fluid rather than the granular medium. This is crucial when the injection point is locally clogged. The experiments show that fracturing conditions are controlled by different mechanisms. Dimensional and statistical analysis was used to classify the injection pressures to regimes predicted by fracturing theory or by Darcy law with modified effective permeabilities. The findings show that both the material properties and fluid composition are important designing parameters.

Tensile Strength of Artificially Cemented Sandstone Generated via Microbially Induced Carbonate Precipitation.

Artificially bio-cemented sands treated with microbially induced calcite precipitation are weakly cemented rocks representing intermediate materials between locked and carbonate sands. Variations in cementation significantly affect the strength of sample, particularly tensile stregth. The modes of fracture and the surface characteristics resulting from the indirect tensile strength tests (Brazilian tests) are strongly correlated with the specimen strength and consequently the degree of cementation. This study examines the tensile strength of bio-cemented fine and coarse sands (average particle diameter 0.18 and 1.82 mm, respectively) and investigates failure modes by recording fracture evolution at both sides of specimen and surface characteristics of the reconstructed surfaces. The dimensionless slope parameter Z2 provided the best fit with respect to tensile strength while the power spectral density was a good indicator of surface anisotropy. Finally, wavelet decomposition allowed for comparison of fracture surface characteristics of the two sands ignoring the grain size effects.

The role of bacterial urease activity on the uniformity of carbonate precipitation profiles of bio-treated coarse sand specimens.

Protocols for microbially induced carbonate precipitation (MICP) have been extensively studied in the literature to optimise the process with regard to the amount of injected chemicals, the ratio of urea to calcium chloride, the method of injection and injection intervals, and the population of the bacteria, usually using fine- to medium-grained poorly graded sands. This study assesses the effect of varying urease activities, which have not been studied systematically, and population densities of the bacteria on the uniformity of cementation in very coarse sands (considered poor candidates for treatment). A procedure for producing bacteria with the desired urease activities was developed and qPCR tests were conducted to measure the counts of the RNA of the Ure-C genes. Sand biocementaton experiments followed, showing that slower rates of MICP reactions promote more effective and uniform cementation. Lowering urease activity, in particular, results in progressively more uniformly cemented samples and it is proven to be effective enough when its value is less than 10 mmol/L/h. The work presented highlights the importance of urease activity in controlling the quality and quantity of calcium carbonate cements.

Stress inhomogeneity effect on fluid-induced fracture behavior into weakly consolidated granular systems.

We study the effect of stress inhomogeneity on the behavior of fluid-driven fracture development in weakly consolidated granular systems. Using numerical models we investigate the change in fracture growth rate and fracture pattern structure in unconsolidated granular packs (also referred to as soft-sands) as a function of the change in the confining stresses applied to the system. Soft-sands do not usually behave like brittle, linear elastic materials, and as a consequence, poroelastic models are often not applicable to describe their behavior. By making a distinction between "cohesive" and "compressive" grain-grain contact forces depending on their magnitude, we propose an expression that describes the fluid opening pressure as a function of the mean value and the standard deviation of the "compressive stress" distribution. We also show that the standard deviation of this distribution can be related with the extent to which fracture "branches" reach into the material.