Cathode Interface Construction by Rapid Sintering in Solid-State Batteries.

Solid-state batteries (SSBs) are poised to replace traditional organic liquid-electrolyte lithium-ion batteries due to their higher safety and energy density. Oxide-based solid electrolytes (SEs) are particularly attractive for their stability in air and inability to ignite during thermal runaway. However, achieving high-performance in oxide-based SSBs requires the development of an intimate and robust SE-cathode interface to overcome typically large interfacial resistances. The transition interphase should be both physically and chemically active. This study presents a thin, conductive interphase constructed between lithium aluminum titanium phosphate and lithium cobalt oxide using a rapid sintering method that modifies the interphase within 10 s. The rapid heating and cooling rates restrict side reactions and interdiffusion on the interface. SSBs with thick composite cathodes demonstrate a high initial capacity of ≈120 mAh g-1 over 200 cycles at room temperature. Furthermore, the rapid sintering method can be extended to other cathode systems under similar conditions. These findings highlight the importance of constructing an appropriate SE-cathode interface and provide insight into designing practical SSBs.

Epitaxial Growth and Integration of Insulating Metal-Organic Frameworks in Electrochemistry.

With tunable pore size and rich active metal centers, metal-organic frameworks (MOFs) have been regarded as the one of the promising materials for catalysis. Prospectively, employing MOFs in electrochemistry would notably broaden the scope of electrocatalysis. However, this application is largely hindered by MOFs' conventionally poor electrical conductivity. Integrating MOFs without compromising their crystalline superiority holds a grand challenge to unveil their pristine electrocatalytic properties. In this work, we introduce an epitaxial growth strategy to accomplish the efficient integration of the insulating MOFs into electrochemistry. Particularly, with pristine-graphene-templated growth, the two-dimensional (2D) single-crystal MOF possesses a large lateral size of ∼23 µm and high aspect ratio up to ∼1500 and exhibits a significant electrochemical enhancement, with a charge transfer resistance of ∼200 ohm and a 30 mA cm-2 current density at only 0.53 V versus a reversible hydrogen electrode. The epitaxial strategy could be further applied to other 2D substrates, such as MoS2. This MOF/graphene 2D architecture sheds light on integrating insulating MOFs into electrochemical applications.

Electrochemical sensing performance of two CuO nanomaterial-modified dual-working electrodes.

Two CuO nanostructures, namely, nanospheres (CuONSs) and nanochains (CuONCs) with different shapes but similar diameters, were synthesized and characterized. With these two nanomaterials as electrode modifiers, a systematic comparative study was conducted to examine their electrochemical sensing of catechol (CT) using a dual-working electrode system. The results suggest that for CuONS- and CuONC-modified glassy carbon electrodes, the electrode process for the CT redox is diffusion-controlled, and the modification amount and electrolyte pH have a similar effect on the response. However, the CuONCs showed a higher peak current and lower peak potential, as well as a lower detection limit for the electrochemical oxidation of CT. This is explained by the lower charge transfer impedance and higher electroactive surface area of the CuONCs. Notably, an unexpected peak appeared in the cyclic voltammograms when the pH was <4 for the CuONCs and <3 for the CuONSs. For this phenomenon, UV-Vis spectra, zeta potential, and size distribution experiments demonstrated changes in the two CuO nanostructures at lower pH, illustrating that CuONSs can tolerate a higher pH as compared to CuONCs. The multiple comparisons between the two nanomaterials presented here can provide references for the selection of electrochemical sensing materials.

Kinetically Controlled Synthesis of Metallic Glass Nanoparticles with Expanded Composition Space.

Nanoscale metallic glasses offer opportunities for investigating fundamental properties of amorphous solids and technological applications in biomedicine, microengineering, and catalysis. However, their top-down fabrication is limited by bulk counterpart availability, and bottom-up synthesis remains underexplored due to strict formation conditions. Here, a kinetically controlled flash carbothermic reaction is developed, featuring ultrafast heating (>105 K s-1) and cooling rates (>104 K s-1), for synthesizing metallic glass nanoparticles within milliseconds. Nine compositional permutations of noble metals, base metals, and metalloid (M1─M2─P, M1 = Pt/Pd, M2 = Cu/Ni/Fe/Co/Sn) are synthesized with widely tunable particle sizes and substrates. Through combinatorial development, a substantially expanded composition space for nanoscale metallic glass is discovered compared to bulk counterpart, revealing that the nanosize effect enhances glass forming ability. Leveraging this, several nanoscale metallic glasses are synthesized with composition that have never, to the knowledge, been synthesized in bulk. The metallic glass nanoparticles exhibit high activity in heterogeneous catalysis, outperforming crystalline metal alloy nanoparticles.

Preparation and investigation of novel endopeptidase-exopeptidase co-immobilized nanoflowers with improved cascade hydrolysis.

Enzymatic hydrolysis is a promising approach for protein and food processing. However, the efficiency of this approach is constrained by the self-hydrolysis, self-agglomeration of free enzymes and the limited applicability resulted from enzymes' selectivityt. Here, novel organic-inorganic hybrid nanoflowers (AY-10@AXH-HNFs) were prepared by coordinating Cu2+ with both endopeptidase of PROTIN SD-AY10 and exopeptidase of Prote AXH. The results indicate that the AY-10@AXH-HNFs exhibited 4.1 and 9.6 times higher catalytic activity than free Prote AXH and PROTIN SD-AY10, respectively, for the enzymatic hydrolysis of N-benzoyl-L-arginine ethyl ester (BAEE). The kinetic parameters of Km, Vmax and Kcat/Km by AY-10@AXH-HNFs were determined to be 0.6 mg/mL, 6.8 mL·min/mg and 6.1 mL/(min·mg), respectively, surpassing the values obtained from free endopeptidase and exopeptidase. Furthermore, the ability of AY-10@AXH-HNFs to retain 41 % of their initial catalytic activity after undergoing 5 cycles of repeated use confirmed their stability and reusability. This study introduces a novel approach of co-immobilizing endopeptidase and exopeptidase on nanoflowers, resulting in significantly enhanced stability and reusability of the protease in catalytic applications.

Local travel behaviour under continuing COVID-19 waves- A proxy for pandemic fatigue?

COVID-19 continues to threaten the world. Relaxing local travel behaviours on preventing the spread of COVID-19, may increase the infection risk in subsequent waves of SARS-CoV-2 transmission. In this study, we analysed changes in the travel behaviour of different population groups (adult, child, student, elderly) during four pandemic waves in Hong Kong before January 2021, by 4-billion second-by-second smartcard records of subway. A significant continuous relaxation in human travel behaviour was observed during the four waves of SARS-CoV-2 transmission. Residents sharply reduced their local travel by 51.9%, 50.1%, 27.6%, and 20.5% from the first to fourth pandemic waves, respectively. The population flow in residential areas, workplaces, schools, shopping areas, amusement areas and border areas, decreased on average by 30.3%, 33.5%, 41.9%, 58.1%, 85.4% and 99.6%, respectively, during the pandemic weeks. We also found that many other cities around the world experienced a similar relaxation trend in local travel behaviour, by comparing traffic congestion data during the pandemic with data from the same period in 2019. The quantitative pandemic fatigue in local travel behaviour could help governments partially predicting personal protective behaviours, and thus to suggest more accurate interventions during subsequent waves, especially for highly infectious virus variants such as Omicron.

Upcycling of Waste Plastic into Hybrid Carbon Nanomaterials.

Graphitic 1D and hybrid nanomaterials represent a powerful solution in composite and electronic applications due to exceptional properties, but large-scale synthesis of hybrid materials has yet to be realized. Here, a rapid, scalable method to produce graphitic 1D materials from polymers using flash Joule heating (FJH) is reported. This avoids lengthy chemical vapor deposition and uses no solvent or water. The flash 1D materials (F1DM), synthesized using a variety of earth-abundant catalysts, have controllable diameters and morphologies by parameter tuning. Furthermore, the process can be modified to form hybrid materials, with F1DM bonded to turbostratic graphene. In nanocomposites, F1DM outperform commercially available carbon nanotubes. Compared to current 1D material synthetic strategies using life cycle assessment, FJH synthesis represents an 86-92% decrease in cumulative energy demand and 92-94% decrease in global-warming potential. This work suggests that FJH affords a cost-effective and sustainable route to upcycle waste plastic into valuable 1D and hybrid nanomaterials.

Battery metal recycling by flash Joule heating.

The staggering accumulation of end-of-life lithium-ion batteries (LIBs) and the growing scarcity of battery metal sources have triggered an urgent call for an effective recycling strategy. However, it is challenging to reclaim these metals with both high efficiency and low environmental footprint. We use here a pulsed dc flash Joule heating (FJH) strategy that heats the black mass, the combined anode and cathode, to >2100 kelvin within seconds, leading to ~1000-fold increase in subsequent leaching kinetics. There are high recovery yields of all the battery metals, regardless of their chemistries, using even diluted acids like 0.01 M HCl, thereby lessening the secondary waste stream. The ultrafast high temperature achieves thermal decomposition of the passivated solid electrolyte interphase and valence state reduction of the hard-to-dissolve metal compounds while mitigating diffusional loss of volatile metals. Life cycle analysis versus present recycling methods shows that FJH significantly reduces the environmental footprint of spent LIB processing while turning it into an economically attractive process.

Heteroatom-Doped Flash Graphene.

Heteroatom doping can effectively tailor the local structures and electronic states of intrinsic two-dimensional materials, and endow them with modified optical, electrical, and mechanical properties. Recent studies have shown the feasibility of preparing doped graphene from graphene oxide and its derivatives via some post-treatments, including solid-state and solvothermal methods, but they require reactive and harsh reagents. However, direct synthesis of various heteroatom-doped graphene in larger quantities and high purity through bottom-up methods remains challenging. Here, we report catalyst-free and solvent-free direct synthesis of graphene doped with various heteroatoms in bulk via flash Joule heating (FJH). Seven types of heteroatom-doped flash graphene (FG) are synthesized through millisecond flashing, including single-element-doped FG (boron, nitrogen, oxygen, phosphorus, sulfur), two-element-co-doped FG (boron and nitrogen), as well as three-element-co-doped FG (boron, nitrogen, and sulfur). A variety of low-cost dopants, such as elements, oxides, and organic compounds are used. The graphene quality of heteroatom-doped FG is high, and similar to intrinsic FG, the material exhibits turbostraticity, increased interlayer spacing, and superior dispersibility. Electrochemical oxygen reduction reaction of different heteroatom-doped FG is tested, and sulfur-doped FG shows the best performance. Lithium metal battery tests demonstrate that nitrogen-doped FG exhibits a smaller nucleation overpotential compared to Cu or undoped FG. The electrical energy cost for the synthesis of heteroatom-doped FG synthesis is only 1.2 to 10.7 kJ g-1, which could render the FJH method suitable for low-cost mass production of heteroatom-doped graphene.

High-surface-area corundum nanoparticles by resistive hotspot-induced phase transformation.

High-surface-area α-Al2O3 nanoparticles are used in high-strength ceramics and stable catalyst supports. The production of α-Al2O3 by phase transformation from γ-Al2O3 is hampered by a high activation energy barrier, which usually requires extended high-temperature annealing (~1500 K, > 10 h) and suffers from aggregation. Here, we report the synthesis of dehydrated α-Al2O3 nanoparticles (phase purity ~100%, particle size ~23 nm, surface area ~65 m2 g-1) by a pulsed direct current Joule heating of γ-Al2O3. The phase transformation is completed at a reduced bulk temperature and duration (~573 K, < 1 s) via an intermediate δ'-Al2O3 phase. Numerical simulations reveal the resistive hotspot-induced local heating in the pulsed current process enables the rapid transformation. Theoretical calculations show the topotactic transition (from γ- to δ'- to α-Al2O3) is driven by their surface energy differences. The α-Al2O3 nanoparticles are sintered to nanograined ceramics with hardness superior to commercial alumina and approaching that of sapphire.

Turbostratic Boron-Carbon-Nitrogen and Boron Nitride by Flash Joule Heating.

Turbostratic layers in 2D materials have an interlayer misalignment. The lack of alignment expands the intrinsic interlayer distances and weakens the optical and electronic interactions between adjacent layers. This introduces properties distinct from those structures with well-aligned lattices and strong coupling interactions. However, direct and rapid synthesis of turbostratic materials remains a challenge owing to their thermodynamically metastable properties. Here, a flash Joule heating (FJH) method to achieve bulk synthesis of boron-carbon-nitrogen ternary compounds with turbostratic structures by a kinetically controlled ultrafast cooling process that takes place within milliseconds (103  to 104 K s-1 ) is reported. Theoretical calculations support the existence of turbostratic structures and provide estimates of the energy barriers with respect to conversion into the corresponding well-aligned counterparts. When using non-carbon conductive additives, a direct synthesis of boron nitride is possible. The turbostratic nature facilitates mechanical exfoliation and more stable dispersions. Accordingly, the addition of flash products to a poly(vinyl alcohol) nanocomposite film coating a copper surface greatly improves the copper's resistance to corrosion in 0.5 m sulfuric acid or 3.5 wt% saline solution. FJH allows the use of bulk materials as reactants and provides a rapid approach to large quantities of the hitherto hard-to-access turbostratic materials.

Millisecond Conversion of Metastable 2D Materials by Flash Joule Heating.

Controllable phase engineering is vital for precisely tailoring material properties since different phase structures have various electronic states and atomic arrangements. Rapid synthesis of thermodynamically metastable materials, especially two-dimensional metastable materials, with high efficiency and low cost remains a large challenge. Here we report flash Joule heating (FJH) as an electrothermal method to achieve the bulk conversion of transition metal dichalcogenides, MoS2 and WS2, from 2H phases to 1T phases in milliseconds. The conversions can reach up to 76% of flash MoS2 using tungsten powder as conductive additive. Different degrees of phase conversion can be realized by controlling the FJH conditions, such as reaction duration and additives, which allows the study of ratio-dependent properties. First-principles calculations confirm that structural processes associated with the FJH, such as vacancy formation and charge accumulation, result in stabilization of the 1T phases. FJH offers rapid access to bulk quantities of the hitherto hard-to-access 1T phases, a promising method for further fundamental research and diverse applications of metastable phases.

Laser-Induced Silicon Oxide for Anode-Free Lithium Metal Batteries.

The development of a rechargeable Li metal anode (LMA) is an important milestone for improved battery technology. Practical issues hindering LMAs are the formation of Li dendrites and inactive Li during plating and stripping processes, which can cause short circuits, thermal runaway, and low coulombic efficiency (CE). Here, the use of a laser-induced silicon oxide (LI-SiOx ) layer derived from a commercial adhesive tape to improve the reversibility of Li metal batteries (LMBs) is studied. The silicone-based adhesive of the tape is converted by a commercial infrared laser into a homogeneous porous SiOx layer deposited directly over the current collector. The coating results in superior performance by suppressing the formation of Li dendrites and inactive Li and presenting higher average CE of 99.3% (2.0 mAh cm-2 at 2.0 mA cm-2 ) compared to bare electrodes. The thickness and morphology of the deposited Li is investigated, revealing a different mechanism of Li deposition on coated electrodes. The laser coating affords a method that is fast and avoids the use of toxic organic solvents and extensive drying times. The improved performance with the SiOx coating is demonstrated in LMB with a zero-excess ("anode-free") configuration where a 100% improved performance is verified.

Metal-Organic Framework for Transparent Electronics.

Electronics allowing for visible light to pass through are attractive, where a key challenge is to make the core functional units transparent. Here, it is shown that transparent electronics can be constructed by epitaxial growth of metal-organic frameworks (MOFs) on single-layer graphene (SLG) to give a desirable transparency of 95.7% to 550 nm visible light and an electrical conductivity of 4.0 × 104 S m-1. Through lattice and symmetry match, collective alignment of MOF pores and dense packing of MOFs vertically on SLG are achieved, as directly visualized by electron microscopy. These MOF-on-SLG constructs are capable of room-temperature recognition of gas molecules at the ppb level with a linear range from 10 to 108 ppb, providing real-time gas monitoring function in transparent electronics. The corresponding devices can be fabricated on flexible substrates with large size, 3 × 5 cm, and afford continuous folding for more than 200 times without losing conductivity or transparency.

Development of reprocessable novel sulfur-containing epoxy based on thermal treatment.

Inspired by the Diels-Alder reaction (DA reaction), the product of the reaction of 2-thiophenecarboxaldehyde (TCD) with epichlorohydrin (ECH) was combined with 1,4-anthraquinone to form a DA structure (a sulfur-containing self-healing epoxy resin (EP-DA) containing a large amount of π-electrons) was synthesized. The chemical structure, thermal properties, thermo-reversibility and tribological properties of EP-DA were studied by FTIR, DSC, gel-sol conversion and MRH-3G, respectively. The results indicated that the as-prepared epoxy composite network, which contains the thermally reversible D-A bond, enabled the epoxy resin to undergo self-repair. Moreover, the waste epoxy resin can be recycled and reused. The friction and wear of the epoxy during actual use were simulated. Macroscopic qualitative observation and quantitative measurement of shearing and peeling recovery were combined to examine the repair behavior and reprocessing ability of EP-DA, confirming that this material has good performance of self-repair and reprocessability, with the highest repair efficiency of up to 83.4%. Moreover, the introduced sulfur-containing diene body greatly improved the lubricating performance of the material, and the treatment time of waste reprocessing had a great influence on the content of the sulfur-containing epoxy monomer in the final EP-DA film. It was often possible to determine the degree of recovery of frictional properties. Inspired by the D-A reaction, a self-assembled large molecule that shares a large number of π-electrons is constructed.