Size-controlled synthesis of ZnO quantum dots in microreactors.

In this paper, we report on a continuous-flow microreactor process to prepare ZnO quantum dots (QDs) with widely tunable particle size and photoluminescence emission wavelengths. X-ray diffraction, electron diffraction, UV-vis, photoluminescence and transmission electron microscopy measurements were used to characterize the synthesized ZnO QDs. By varying operating conditions (temperature, flow rate) or the capping ligand, ZnO QDs with diameters ranging from 3.6 to 5.2 nm and fluorescence maxima from 500 to 560 nm were prepared. Results obtained show that low reaction temperatures (20 or 35 °C), high flow rates and the use of propionic acid as a stabilizing agent are favorable for the production of ZnO QDs with high photoluminescence quantum yields (up to 30%).

Performance, Efficiency, and Flexibility Analysis of a High-Temperature Proton Exchange Membrane Fuel Cell-Based Micro-Combined Heat-and-Power System with Intensification of the Steam Methane Reforming Step by Using a Millistructured Reactor.

The complete simulation model of an existing 1 kW high-temperature proton exchange membrane (HT-PEM) fuel cell-based residential micro-combined heat-and-power process, including a compact intensified heat-exchanger-reactor, is developed in the simulation software ProSimPlus v3.6.16. Detailed simulation models of the heat-exchanger-reactor, a mathematical model of the HT-PEM fuel cell, and other components are presented. The results obtained by the simulation model and by the experimental micro-cogenerator are compared and discussed. To fully understand the behavior of the integrated system and assess its flexibility, a parametric study is performed considering fuel partialization and important operating parameters. The values of the air-to-fuel ratio = [30, 7.5] and steam-to-carbon ratio = 3.5 (corresponding to net electrical and thermal efficiencies of 21.5 and 71.4%) are chosen for the analysis of inlet/outlet component temperatures. Finally, the exchange network analysis of the full process proves that the process efficiencies can still be increased by further improving the process internal heat integration.

Use of surfactants to reduce the driving voltage of switchable optical elements based on electrowetting.

The advantage of using electrowetting as a novel principle for a reflective display has been previously demonstrated. The principle is based on the controlled two-dimensional movement of an oil/water interface across a hydrophobic fluoropolymer insulator. The main objective of this paper is to show experimentally the influence of surfactants on the electro-optic behavior of a single electrowetting pixel. The concentration and type of nonionic surfactant (Tween 80 and Span 20) have been varied. The experimental data are compared with calculations from the electro-optic model developed previously. The electro-optic performance is significantly affected by the nature and the concentration of surfactant. In the presence of Tween, at concentrations lower than the critical micelle concentration (CMC), and mixtures of Tween and Span the electro-optic behavior can be related to the interfacial tension. When decreasing the oil/water interfacial tension, the amplitude of the driving voltage required for obtaining a given oil displacement decreases and the switching curve becomes steeper. These effects can be accurately reproduced by means of the previously developed electro-optic model. Mixtures of Tween and Span produce a significant synergetic reduction of the driving voltage. For Tween concentrations higher than the CMC and Span, a strong disagreement is observed between the previously developed model and experimental data. Here a new physical model is reported that describes the electro-optic behavior of electrowetting-based optical elements in the presence of surfactants. The model takes into account the actual voltage used to control the liquid movement in electrowetting (lower than the applied voltage), the amount of surfactant adsorbed at the decane/water interface, and the dipole moment of the surfactant molecules. The calculated results are in very good agreement with experimental data without employing fitting parameters. The dipoles interact with the applied field and lower the actual applied field. This reduction of the effective electric field across the solid-liquid interface induces a decrease in the charge density at the solid-liquid interface and reduces the electrowetting force. For surfactant concentrations higher than the CMC, the electro-optic performance does not depend on the surfactant concentration. This demonstrates that the reduction of the electrowetting field due to the large dipole moment of the surfactant molecules occurs at the oil/water interface. A new method for the test cell fabrication is also presented.

CFD Investigation of the effects of bubble aerator layouts on hydrodynamics of an activated sludge channel reactor.

In this paper, computational fluid dynamics (CFD) simulations are employed to characterize the effects of bubble aerator layouts (i.e. spatial arrangement) on the hydrodynamics in activated sludge (AS) reactors. The first configuration considered is a channel reactor with aerators placed alongside one lateral wall, for which velocity measurements are available in literature. CFD results were in good agreement with experimental data, which proves that the model is sufficiently accurate and predictive. Accordingly, simulations and numerical residence time distribution tests were conducted for different aerator layouts to determine their effects on the reactor hydrodynamics. The results revealed that the flow characteristics are extremely sensitive to the aerators arrangement given the high gas flow rates used in AS processes. Among the layouts investigated, the one where diffusers are placed all over the reactor floor has led to the least dispersive flow, i.e. which characteristics best tend toward that of an ideal plug flow reactor. Indeed, this flow field presented the lowest average turbulent diffusion and the most uniform axial velocity and turbulence fields. Such a flow behaviour is expected to be highly beneficial for biological treatment since it reduces pollutant dilution by axial diffusion and limits raw wastewater channelling to the outlet.