RESUMO
Precipitation during the viral inactivation, neutralization and depth filtration step of a monoclonal antibody (mAb) purification process can provide quantifiable and potentially significant impurity reduction. However, robust commercial implementation of this unit operation is limited due to the lack of a representative scale-down model to characterize the removal of impurities. The objective of this work is to compare isoelectric impurity precipitation behavior for a monoclonal antibody product across scales, from benchtop to pilot manufacturing. Scaling parameters such as agitation and vessel geometry were investigated, with the precipitate amount and particle size distribution (PSD) characterized via turbidity and flow imaging microscopy. Qualitative analysis of the data shows that maintaining a consistent energy dissipation rate (EDR) could be used for approximate scaling of vessel geometry and agitator speeds in the absence of more detailed simulation. For a more rigorous approach, however, agitation was simulated via computational fluid dynamics (CFD) and these results were applied alongside a population balance model to simulate the trajectory of the size distribution of precipitate. CFD results were analyzed within a framework of a two-compartment mixing model comprising regions of high- and low-energy agitation, with material exchange between the two. Rate terms accounting for particle formation, growth and breakage within each region were defined, accounting for dependence on turbulence. This bifurcated model was successful in capturing the variability in particle sizes over time across scales. Such an approach enhances the mechanistic understanding of impurity precipitation and provides additional tools for model-assisted prediction for process scaling.
Assuntos
Anticorpos Monoclonais , Precipitação Química , Hidrodinâmica , Tamanho da Partícula , Anticorpos Monoclonais/química , Anticorpos Monoclonais/isolamento & purificaçãoRESUMO
This paper reports the design and qualification of the first purpose-built, bench-scale reactor system to model the municipal waste-to-energy combustion of fluorinated polymers. Using the principle of similarity, the gas-phase combustion zone of a typical municipal waste-to-energy plant has been scaled down to the bench with a focus on chemical similarity. Chemical similarity is achieved in large part through the use of methanol as a surrogate for municipal solid waste (MSW). Review of prior research shows that methanol is one of the major volatile products expected during MSW thermal conversion in the fuel bed of waste-to-energy plants. Like full-scale waste-energy plants, the design of the bench-scale model includes a flame zone and a post-flame zone. Maintaining steady methanol vapor flow premixed with air to the model reactor system ensures stable combustion resulting in bench-scale CO emission levels comparable to those of full-scale waste-to-energy plants. Since investigation of fluorinated polymer combustion includes trace analysis of exhaust gas for perfluorooctanoic acid (PFOA), qualification testing focused on PFOA collection efficiency. High PFOA collection efficiency (>90%) demonstrated the capability of the reactor system in transporting and absorbing PFOA that may be generated during high-temperature combustion testing of fluorinated polymers. Overall, the bench-scale system is qualified for its intended use to investigate potential generation of PFOA from combustion of fluorinated polymers under conditions representative of waste-to-energy combustion.Implications: Decision-makers depend on environmental researchers to provide reliable predictions of pollutant emissions from waste combustion of polymers at end of product life. Reliable predictions are especially important with regard to questions about potential PFOA emissions from municipal waste combustion of fluorinated polymers. Results from qualification testing confirm that the novel bench-scale model reactor system is capable of representing gas-phase municipal waste combustion behavior upstream of air pollution control and generating representative exhaust gas samples for off-line trace-level analysis of PFOA.
Assuntos
Incineração , Metanol , Polímeros de Fluorcarboneto , Gases/análise , Incineração/métodos , Resíduos Sólidos/análiseRESUMO
Gelation can occur in polymer, hydrogel, and colloid systems that undergo reversible aggregation-fragmentation (crosslinking accompanied by breakage). Gelation, characterized by rapid divergence of weight-average molecular weight and viscosity due to initial network formation, can be reversed if conditions change. In this paper, reversible aggregation and fragmentation in the pre-gelation time period are modeled with distribution kinetics. Moment equations are obtained from the population balance equation, and solved for eight different rate kernels. We identify the cases for which gelation is possible and obtain the critical values for the rate constants that allow gelation. The model provides a good simulation of published experimental data for aggregation and degradation of plasticized wheat gluten during thermo-mechanical treatments. We also evaluate two closure approximations based on Gamma and log-normal distributions, and conclude that log-normal closure predicts all five possible steady states, in agreement with the Vigil-Ziff criterion, and Gamma closure predicts only three. However, Gamma closure approximates the steady state either closely or exactly, whereas log-normal closure only poorly approximates the steady-state distribution.