Bendable Zeolite Membranes: Synthesis and Improved Gas Separation Performance.

Separation and sequestration of CO2 emitted from fossil energy fueled electric generating units and industrial facilities will help in reducing anthropogenic CO2, thereby mitigating its adverse climate change effects. Membrane-based gas separation has the potential to meet the technical challenges of CO2 separation if high selectivity and permeance with low costs for large-scale manufacture are realized. Inorganic zeolite membranes in principle can have selectivity and permeance considerably higher than polymers. This paper presents a strategy for zeolite growth within the pores of a polymer support, with crystallization time of an hour. With a thin coating of 200-300 nm polydimethylsiloxane (PDMS) on the zeolite-polymer composite, transport data for CO2/N2 separation indicate separation factors of 35-45, with CO2 permeance between 1600 and 2200 GPU (1 GPU = 3.35 × 10(-10) mol/(m(2) s Pa)) using dry synthetic mixtures of CO2 and N2 at 25 °C. The synthesis process results in membranes that are highly reproducible toward transport measurements and exhibit long-term stability (3 days). Most importantly, these membranes because of the zeolite growth within the polymer support, as contrasted to conventional zeolite growth on top of a support, are mechanically flexible.

Rapid crystallization of faujasitic zeolites: mechanism and application to zeolite membrane growth on polymer supports.

Zeolites are microporous, crystalline aluminosilicates with the framework made up of T-O-T (T = Si, Al) bonds and enclosed cages and channels of molecular dimensions. Influencing and manipulating the nucleation and growth characteristics of zeolites can lead to novel frameworks and morphologies, as well as decreased crystallization time. In this study, we show that manipulating the supersaturation during synthesis of zeolite X/Y (FAU) via dehydration led to extensive nucleation. Controlled addition of water to this nucleated state promotes the transport of nutrients, with a 4-fold increase in the rate of crystal growth, as compared to conventional hydrothermal process. Structural signature of the nucleated state was obtained by electron microscopy, NMR, and Raman spectroscopy. This extensively intermediate nucleated state was isolated and used as the starting material for zeolite membrane synthesis on porous polymer supports, with membrane formation occurring within an hour. With this time frame for growth, it becomes practical to fabricate zeolite/polymer membranes using roll-to-roll technology, thus making possible new commercial applications.

Commercial Silver-Based Dressings: In Vitro and Clinical Studies in Treatment of Chronic and Burn Wounds.

Chronic wounds are a major health problem because of delayed healing, causing hardships for the patient. The infection present in these wounds plays a role in delayed wound healing. Silver wound dressings have been used for decades, beginning in the 1960s with silver sulfadiazine for infection prevention for burn wounds. Since that time, there has been a large number of commercial silver dressings that have obtained FDA clearance. In this review, we examine the literature involving in vitro and in vivo (both animal and human clinical) studies with commercial silver dressings and attempt to glean the important characteristics of these dressings in treating infected wounds. The primary presentation of the literature is in the form of detailed tables. The narrative part of the review focuses on the different types of silver dressings, including the supporting matrix, the release characteristics of the silver into the surroundings, and their toxicity. Though there are many clinical studies of chronic and burn wounds using silver dressings that we discuss, it is difficult to compare the performances of the dressings directly because of the differences in the study protocols. We conclude that silver dressings can assist in wound healing, although it is difficult to provide general treatment guidelines. From a wound dressing point of view, future studies will need to focus on new delivery systems for silver, as well as the type of matrix in which the silver is deposited. Clearly, adding other actives to enhance the antimicrobial activity, including the disruption of mature biofilms is of interest. From a clinical point of view, the focus needs to be on the wound healing characteristics, and thus randomized control trials will provide more confidence in the results. The application of different wound dressings for specific wounds needs to be clarified, along with the application protocols. It is most likely that no single silver-based dressing can be used for all wounds.

Minimal intestinal epithelial cell toxicity in response to short- and long-term food-relevant inorganic nanoparticle exposure.

Toxicity of commercial nanoparticles of titania, silica, and zinc oxides is being investigated in this in vitro study. Particles of these compositions are found in many food items, and thus this study is directed toward particle behavior in simulated digestion media and their interaction with intestinal epithelial cell line C2BBe1, a clone of Caco-2 cells, originally isolated from a human colon cancer. Even though the primary particle size of all three particles was below 50 nm, the particles appeared as aggregates in culture media with a negatively charged surface. In the presence of pepsin (pH 2), the charge on the titania became positive, and silica was almost neutral and aggregated extensively, whereas ZnO dissolved. For silica and titania, treatment with simulated intestinal digestive solution led to a strongly negatively charged surface and particle sizes approaching values similar to those in media. On the basis of infrared spectroscopy, we concluded that the surface of silica and titania was covered with bile salts/proteins after this treatment. Transmission electron microscopy indicated that the C2BBe1 cells internalized all three particles. Toxicity assays included investigation of necrosis, apoptosis, membrane damage, and mitochondrial activity. Titania and SiO2 particles suspended in media at loading levels of 10 µg/cm² exhibited no toxicity. With ZnO at the same loading level, mild toxicity was observed based only on the LDH assay and decrease of mitochondrial activity and not necrosis or apoptosis. Titania particles exposed to the simulated digestion media exhibited mild toxicity based on decrease of mitochondrial activity, likely due to transport of toxic bile salts via adsorption on the particle surface.

Tuning the activities and structures of enzymes bound to graphene oxide with a protein glue.

Graphene oxide (GO) is being investigated extensively for enzyme and protein binding, but many enzymes bound to GO denature considerably and lose most of their activities. A simple, novel, and efficient approach is described here for improving the structures and activities of enzymes bound to GO such that bound enzymes are nearly as active as those of the corresponding unbound enzymes. Our strategy is to preadsorb highly cationized bovine serum albumin (cBSA) to passivate GO, and cBSA/GO (bGO) served as an excellent platform for enzyme binding. The binding of met-hemoglobin, glucose oxidase, horseradish peroxidase, BSA, catalase, lysozyme, and cytochrome c indicated improved binding, structure retention, and activities. Nearly 100% of native-like structures of all the seven proteins/enzymes were noted at near monolayer formation of cBSA on GO (400% w/w), and all bound enzymes indicated 100% retention of their activities. A facile, benign, simple, and general method has been developed for the biofunctionalization of GO, and this approach of coating with suitable protein glues expands the utility of GO as an advanced biophilic nanomaterial for applications in catalysis, sensing, and biomedicine.

Influence of crystallite size on cation conductivity in faujasitic zeolites.

The influence of particle size on the ionic conductivity of ceramic materials is an active area of research, and novel effects are observed as particles approach the nanoscale in size. Zeolites are crystalline aluminosilicates with ion-exchangeable cations that are responsible for ionic conductivity at high temperatures. In this paper, we present systematic results for the first time of ionic conductivity in alkali metal ion-exchanged faujasitic zeolites with morphologies ranging from a zeolite membrane, micrometer-sized, submicrometer, and nanoparticles of zeolite. Using impedance spectroscopy in the range of 10 MHz to 0.1 Hz, we have obtained the activation energy (E(act)) of cation motion with these various morphologies in the temperature range of 525-625 °C. Overall, the E(act) decreases with Si/Al ratio. Surface modification of the zeolite particles was carried out with a silylating agent, which upon high temperature calcination should lead to the formation of a monolayer Si-O-Si film on the particle surface. This surface modification had minimal influence on the E(act) of micrometer-sized zeolites. However, E(act) increased rapidly as the zeolite particle approached the nanoscale. These observations led us to propose that, for the high-temperature, low-frequency (10(4)-10(5) Hz), long-range ionic conduction in zeolites, cation hopping across grain boundaries is relevant to ion transport, especially as the size of the crystallite approaches the nanoscale. Intergrain boundaries are more defective in the nanosized zeolite and contribute to the higher E(act).

Mitigation of SARS-CoV-2 by Using Transition Metal Nanozeolites and Quaternary Ammonium Compounds as Antiviral Agents in Suspensions and Soft Fabric Materials.

Introduction: The coronavirus disease 2019 (COVID-19) pandemic has demonstrated the need for novel, affordable, and efficient reagents to help reduce viral transmission, especially in high-risk environments including medical treatment facilities, close quarters, and austere settings. We examined transition-metal nanozeolite suspensions and quaternary ammonium compounds as an antiviral surface coating for various textile materials. Methods: Zeolites are crystalline porous aluminosilicate materials, with the ability of ion-exchanging different cations. Nanozeolites (30 nm) were synthesized and then ion-exchanged with silver, zinc and copper ions. Benzalkonium nitrate (BZN) was examined as the quaternary ammonium ion (quat). Suspensions of these materials were tested for antiviral activity towards SARS-CoV-2 using plaque assay and immunostaining. Suspensions of the nanozeolite and quat were deposited on polyester and cotton fabrics and the ability of these textiles towards neutralizing SARS-CoV-2 was examined. Results: We hypothesized that transition metal ion containing zeolites, particularly silver and zinc (AM30) and silver and copper (AV30), would be effective in reducing the infectivity of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). Additionally, AM30 and AV30 antiviral potency was tested when combined with a quaternary ammonium carrier, BZN. Our results indicate that exposure of SARS-CoV-2 to AM30 and/or AV30 suspensions reduced viral loads with time and exhibited dose-dependence. Antiviral activities of the combination of zeolite and BZN compositions were significantly enhanced. When used in textiles, AM30 and AV30-coated cotton and polyester fabrics alone or in combination with BZN exhibited significant antiviral properties, which were maintained even after various stress tests, including washes, SARS-CoV-2-repeated exposures, or treatments with soil-like materials. Conclusion: This study shows the efficacy of transition metal nanozeolite formulations as novel antiviral agents and establishes that nanozeolite with silver and zinc ions (AM30) and nanozeolite with silver and copper ions (AV30) when combined with benzalkonium nitrate (BZN) quickly and continuously inactivate SARS-CoV-2 in suspension and on fabric materials.

Effects of surface and morphological properties of zeolite on impedance spectroscopy-based sensing performance.

Measurement by impedance spectroscopy of the changes in intrazeolitic cation motion of pressed pellets of zeolite particles upon adsorption of dimethylmethylphosphonate (DMMP) provides a strategy for sensing DMMP, a commonly used simulant for highly toxic organophosphate nerve agents. In this work, two strategies for improving the impedance spectroscopy based sensing of DMMP on zeolites were investigated. The first one is the use of cerium oxide (CeO(2)) coated on the zeolite surface to neutralize acidic groups that may cause the decomposition of DMMP, and results in better sensor recovery. The second strategy was to explore the use of zeolite Y membrane. Compared to pressed pellets, the membranes have connected supercages of much longer length scales. The zeolite membranes resulted in higher sensitivity to DMMP, but recovery of the device was significantly slower as compared to pressed zeolite pellets.

Exploitation of unique properties of zeolites in the development of gas sensors.

The unique properties of microporous zeolites, including ion-exchange properties, adsorption, molecular sieving, catalysis, conductivity have been exploited in improving the performance of gas sensors. Zeolites have been employed as physical and chemical filters to improve the sensitivity and selectivity of gas sensors. In addition, direct interaction of gas molecules with the extraframework cations in the nanoconfined space of zeolites has been explored as a basis for developing new impedance-type gas/vapor sensors. In this review, we summarize how these properties of zeolites have been used to develop new sensing paradigms. There is a considerable breadth of transduction processes that have been used for zeolite incorporated sensors, including frequency measurements, optical and the entire gamut of electrochemical measurements. It is clear from the published literature that zeolites provide a route to enhance sensor performance, and it is expected that commercial manifestation of some of the approaches discussed here will take place. The future of zeolite-based sensors will continue to exploit its unique properties and use of other microporous frameworks, including metal organic frameworks. Zeolite composites with electronic materials, including metals will lead to new paradigms in sensing. Use of nano-sized zeolite crystals and zeolite membranes will enhance sensor properties and make possible new routes of miniaturized sensors.

Contrast of the biological activity of negatively and positively charged microwave synthesized CdSe/ZnS quantum dots.

Quantum dots (QDs) are semiconductor nanocrystals that have found use in bioimaging, cell tracking, and drug delivery. This article compares the cytotoxicity and cellular interactions of positively and negatively charged CdSe/CdS/ZnS QDs prepared by a microwave method using a murine alveolar macrophage-like cell culture model. Keeping the core semiconductor the same, QD charge was varied by altering the surface capping molecule; negatively charged QDs were formed with mercaptopropionic acid (MPA-QDs) and positively charged QDs with thiocholine (THIO-QDs). The size and charge of these two QDs were investigated in three types of media (RPMI, RPMI + FBS, and X-VIVO serum-free media) relevant for the biological studies. MPA-QDs were found to have negative zeta potential in RPMI, RPMI + FBS, and serum-free media and had sizes ranging from 8 to 54 nm. THIO-QDs suspended in RPMI alone were <62 nm in size, while large aggregates (greater than 1000 nm) formed when these QDs were suspended in RPMI + FBS and serum-free media. THIO-QDs retained positive zeta potential in RPMI and were found to have a negative zeta potential in RPMI + FBS and nearly neutral zeta potential in serum-free media. In a cell culture model, both MPA-QDs and THIO-QDs caused comparable levels of apoptosis and necrosis. Both QDs induced significant tumor necrosis factor-alpha (TNF-α) secretion only at high concentrations (>250 nM). Both types of QDs were internalized via clathrin-dependent endocytosis. Using real-time, live cell imaging, we found that MPA-QDs interact with the cell surface within minutes and progress through the endocytic pathway to the lysosomes upon internalization. With the THIO-QDs, the internalization process was slower, but the pathways could not be mapped because of spectroscopic interference caused by QD aggregates. Finally, MPA-QDs were found to associate with cell surface scavenger receptors, while the THIO-QDs did not. This study indicates that the surface charge and aggregation characteristics of QDs change drastically in biological culture conditions and, in turn, influence nanoparticle and cellular interactions.

Physicochemical and toxicological properties of commercial carbon blacks modified by reaction with ozone.

Ozonation of two commercial carbon blacks (CBs), Printex 90 (P90) and Flammruss 101 (F101), was carried out and changes in their morphology, physical properties, and cytotoxicity were examined. The hypothesis examined was that different methods of manufacture of CBs influence their chemical reactivity and toxicological properties. Structural changes were examined by X-ray photoelectron spectroscopy, infrared spectroscopy, Raman spectroscopy, and electron paramagnetic resonance spectroscopy (EPR). Introduction of surface oxygen functionality upon ozonation led to changes in surface charge, aggregation characteristics, and free radical content of the CBs. However, these changes in surface functionality did not alter the cytotoxicity and release of inflammation markers upon exposure of the CBs to murine macrophages. Interaction of macrophages with F101 resulted in higher levels of inflammatory markers than P90, and the only structural correlation was with the higher persistent radical concentration on the F101.

Synthesis of ultrathin zeolite Y membranes and their application for separation of carbon dioxide and nitrogen gases.

Synthesis of zeolite Y membranes from submicrometer (>100 nm) and nano seed (<100 nm) crystals on alumina supports was examined and the separation characteristics of these membranes for CO(2) and N(2) were studied. Two secondary growth solutions were examined, one for a rapid growth (hours) and one for a slower growth process (days). Membranes formed from the rapid growth solution resulted in 2-2.5 microm thickness, while for the slower growth solution, a dense membrane of 350-600 nm thickness was formed, covered by a 25 microm porous zeolite layer. With the nano seeds as the seeding layer, no membrane was formed. A mechanism involving seed dissolution to initiate membrane formation is concluded. The separation characteristics of membranes for CO(2)/N(2) separation were similar, with very high selectivities for separation (alpha(CO(2),N(2)) > 500). The thicker membrane had lower permeance. By investigating both single gas and mixed gas permeances, strong evidence for a percolative type separation process is obtained.

Fenton activity and cytotoxicity studies of iron-loaded carbon particles.

The chemical and biological properties of iron-loaded manufactured carbon nanoparticles (Flammruss 101) were contrasted with those of an iron-loaded synthetic carbon particle. X-ray photoelectron spectroscopy was used to characterize the iron on the carbon particles. Production of hydroxyl free radicals via the Fenton reaction was monitored by electron paramagnetic resonance spectroscopy. The iron-loaded synthetic carbon particles produced a positive Fenton response, whereas the iron-loaded manufactured carbon particles did not. The source of the Fenton activity of the synthetic carbon particles is proposed to be a soluble iron compound that was formed during the synthesis of the particle. A likely candidate for the soluble iron species is Fe2F5, which was synthesized and its properties were examined. Higher toxicity of Fe2F5 toward murine macrophages compared with other simple iron salts was attributed to soluble iron that was stabilized by the fluoride ligand. The cytotoxicity of manufactured carbon particles toward murine macrophages decreased or remained unaltered upon impregnation with iron compounds.

Optical spectroscopic studies of mononitrated benzo[a]pyrenes.

Spectroscopic properties, including absorption, emission spectra, and excited-state lifetimes of the mononitrated benzo[a]pyrenes (NBaPs), specifically 1-, 3-, and 6-nitrobenzo[a]pyrenes (1-, 3-, and 6-NBaP), are reported, and correlations with structure are developed. With 1- and 3-NBaP, bathochromic shifts are observed in the absorption spectra. The quantum yields of emission display the following trend: BaP >> 6-NBaP > 1-NBaP approximately 3-NBaP. Fluorescence lifetimes for nitrated BaPs were approximately 6 to 7 times shorter than that of BaP. With the help of time-dependent density functional theory (TD-DFT), assignments of the electronic transitions are proposed and are in good agreement with the electronic spectra for the NBaPs in methanol. On the basis of optimization of the triplet states, different photochemical consequences are discussed, and the observed fluorescence quenching is explained. Changes in the electron density distributions in the ground and excited states calculated at the second-order coupled-cluster level using the resolution-of-the-identity approximation (RI-CC2) provide information about the possible mechanism of photochemical reactions of NBaPs. Correlations between the orientation of the nitro group relative to the aromatic plane and the observed properties of the NBaP are discussed.

Identification and characterization of Bacillus anthracis spores by multiparameter flow cytometry.

In response to the need for methods that can rapidly detect potentially virulent Bacillus anthracis spores, we developed a two-color flow cytometric assay capable of simultaneously identifying B. anthracis spores and the presence of spore-associated protective antigen, a virulence marker for strains harboring the pXO1 plasmid.

Visible-light-driven photoreactions of [(bpy)2Ru(II)L]Cl2 in aqueous solutions (bpy = bipyridine, l = 1,2-bis(4-(4'-methyl)-2,2'-bipyridyl) ethene).

Visible-light-induced photoreactions of [(bpy)2Ru(II)L]Cl2 (bpy = bipyridine, L = trans-1,2-bis(4-(4'-methyl)-2,2'-bipyridyl) ethene) in aqueous solution are examined. From pH titrations, it is found that the Ru complex is a stronger base (pKa* = 6) in the excited state than in the ground state (pKa = 4). Photolysis of the [(bpy)2Ru(II)L] complex in solutions at pH 7 and 12 led to formation of species with increased emission quantum yields, approximately 55 nm blue-shift of the emission maximum to 625 nm, and disappearance of the absorption band at 330 nm, the latter arising from the olefinic bond of the L ligand. No spectral changes are observed in solutions at pH < or = 4. With the help of chromatography, mass spectroscopy, Raman spectroscopy, and NMR, photoproducts formed at neutral pH have been analyzed. It is found that the major product is a dimer of [(bpy)2Ru(II)L], dimerizing around the double bond. Photoreactions do not occur in the dark or in the aprotic solvent acetonitrile. We propose that a Ru(III) radical intermediate is formed by photoinduced excited-state electron and proton transfer, which initiates the dimerization. The radical intermediate can also undergo photochemical degradative reductions. Below pH 4, the emission quenching is proposed to arise via protonation of the monoprotonated [(bpy)2Ru(II)LH] followed by electron transfer to the viologen-type moiety created by protonation. The products of photodegradation at pH > 12 are different from those of pH 7, but the mechanism of the degradation at pH > 12 was not elucidated.

Photochemical Water Oxidation in a Buffered Tris(2,2'-bipyridyl)ruthenium-Persulfate System Using Iron(III)-Modified Potassium Manganese Oxides as Catalysts.

Study of manganese oxides for electrocatalytic and photocatalytic oxidation of water is an active area of research. The starting material in this study is a high-surface-area disordered birnessite-like material with K+ in the interlayers (KMnOx). Upon ion-exchange with Fe3+, the disordered layer structure collapses (Fe(IE)MnOx), and the surface area is slightly increased. Structural analysis of the Fe(IE)MnOx included examination of its morphology, crystal structure, vibrational spectra, and manganese oxidation states. Using the Ru(bpy)3 2+-persulfate system, the dissolved and headspace oxygen upon visible light photolysis with highly dispersed Fe(IE)MnOx was measured. The photocatalytic activity for O2 evolution of the Fe(IE)MnOx was three times better than KMnOx, with the highest rate being 9.3 mmolO2 molMn -1 s-1. The improvement of the photocatalytic activity was proposed to arise from the increased disorder and interaction of Fe3+ with the MnO6 octahedra. As a benchmark, colloidal IrO2 was a better photocatalyst by a factor of ∼75 over Fe(IE)MnOx.

Interaction of water with titania: implications for high-temperature gas sensing.

High-temperature gas sensors based on semiconducting metal oxides show potential for optimization of combustion processes, resulting in efficient energy use and minimization of emissions. Such metal oxides can function as gas sensors because of the reaction of the sensing gas (e.g., CO) with ionosorbed oxygen species on the oxide surface with the resulting increase in conductivity. A limitation of metal oxide sensors is their difficulty of distinguishing between different gases. Designing selectivity into sensors necessitates a better understanding of the chemistry of gas-solid interactions at high temperatures. In this paper, we have used in situ infrared spectroscopy to monitor the dehydration of a hydrated anatase surface up to 600 degrees C and also to examine the hydration/dehydration of anatase held at 400 degrees C. When the O-H stretching region (3000-3800 cm(-1)) was primarily focused on, it was found that water loss from the titania surface proceeded at lower temperatures (<200 degrees C) through desorption, whereas at higher temperatures, water dissociation to terminal (approximately 3710 cm(-1)) and bridged (approximately 3660 cm(-1)) hydroxyl groups was noted. With a further increase in temperature to 600 degrees C, the bridged hydroxyl groups disappeared faster than the terminal ones. The electrical resistance of anatase at 600 degrees C was measured in the presence of moist gas streams and resulted in an increase in conductivity in the presence of water. In situ vibrational spectroscopy indicated a temporal correlation between the appearance of the bridging hydroxyl group and the change in electrical resistance. Several possible mechanisms are discussed. The chemical reaction of water with anatase at high temperatures necessitates that water be removed from the gas stream to avoid interference. A strategy involving the use of a hydrophobic microporous filter that can reject water and let gases such as CO pass unimpeded is examined. Successful use of such a concept has been demonstrated with a silicalite filter using moist CO gas streams.

Biocompatibility and antibacterial activity of nitrogen-doped titanium dioxide nanoparticles for use in dental resin formulations.

The addition of antibacterial functionality to dental resins presents an opportunity to extend their useful lifetime by reducing secondary caries caused by bacterial recolonization. In this study, the potential efficacy of nitrogen-doped titanium dioxide nanoparticles for this purpose was determined. Nitrogen doping was carried out to extend the ultraviolet absorbance into longer wavelength blue light for increased biocompatibility. Titanium dioxide nanoparticles (approximately 20-30 nm) were synthesized with and without nitrogen doping using a sol-gel method. Ultraviolet-Visible spectroscopy indicated a band of trap states, with increasing blue light absorbance as the concentration of the nitrogen dopant increased. Electron paramagnetic resonance measurements indicated the formation of superoxide and hydroxyl radicals upon particle exposure to visible light and oxygen. The particles were significantly toxic to Escherichia coli in a dose-dependent manner after a 1-hour exposure to a blue light source (480 nm). Intracellular reactive oxygen species assay demonstrated that the particles caused a stress response in human gingival epithelial cells when exposed to 1 hour of blue light, though this did not result in detectable release of cytokines. No decrease in cell viability was observed by water-soluble tetrazolium dye assay. The results show that nitrogen-doped titanium dioxide nanoparticles have antibacterial activity when exposed to blue light, and are biocompatible at these concentrations.

Comparison of ultrastructural cytotoxic effects of carbon and carbon/iron particulates on human monocyte-derived macrophages.

In this study, we tested the hypothesis that the presence of iron in carbon particulates enhances ultrastructural perturbation in human monocyte-derived macrophages (MDMs) after phagocytosis. We used 1-microm synthetic carbon-based particulates, designed to simulate environmental particulates of mass median aerodynamic diameter < or = 2.5 microm (PM2.5). Cultures of human MDMs or T-lymphocytes (as a nonphagocytic control) were exposed to carbon or carbon/iron particulates for various time periods and examined by transmission electron microscopy for ultrastructural changes. T-cells failed to internalize either of the particulates and showed no organelle or nuclear changes. Conversely, MDMs avidly phagocytized the particulates. MDMs treated with C particulates exhibited morphologic evidence of macrophage activation but no evidence of lysis of organelles. In contrast, MDMs treated with C/Fe particulates exhibited coalescence of particulate-containing lysosomes. This phenomenon was not observed in the case of C particulates. By 24 hr there was a tendency of the C/Fe particulates to agglomerate into loose or compact clusters. Surrounding the compact C/Fe agglomerates was a uniform zone of nearly total organelle lysis. The lytic changes diminished in proportion to the distance from the agglomerate. In such cells, the nucleus showed loss of chromatin. Although C particles induced no detectable oxidative burst on treated MDMs, C/Fe particles induced a nearly 5-fold increase in the extracellular oxidative burst by treated MDMs compared with untreated controls. Iron bound to C particles catalyzed the decomposition of hydrogen peroxide to generate hydroxyl radicals. Results of these studies suggest that, among particulates of similar size, biologic activity can vary profoundly as a function of particulate physicochemical properties.