Immobilisation of contaminants by 'green'-synthesized magnetite as a remediation approach to the phosphogypsum waste leachates model solution.

Contaminant removal from (waste)waters by magnetite is a promising technology. In the present experimental study, a magnetite recycled from the steel industry waste (zero-valent iron powder) was used to investigate the sorption of As, Sb and U in phosphate-free and -rich suspensions, i.e. as a remediation for the acidic phosphogypsum leachates derived from the phosphate fertilizer industry. The results showed up to 98% U removal under controlled pH conditions, while phosphate did not hinder this immobilisation. In contrast, the results confirmed the limited uptake of As and Sb oxyanions by magnetite in presence of phosphate as the competing anion, displaying only 7-11% removal, compared to 83-87% in the phosphate-free sorption experiments. To limit this wastewater problem, raw ZVI anaerobic oxidation was examined as mechanism to increase the pH and as a source of Fe2+ in a first step, and in a second step to remove phosphate via vivianite precipitation, therefore prior to the reaction with magnetite. UV-Vis, XRD and SEM-EDS showed that vivianite precipitation is feasible at pH > 4.5, mainly depending on the phosphate concentration. The higher the [PO43-], the lower is the pH at which vivianite precipitates and the higher the % removal of phosphate from solution. It is anticipated that an optimum 3-steps design with separate reactors controlling the conditions of ZVI oxidation, followed by vivianite precipitation and finally, reaction with magnetite, can achieve high contaminant uptake in field applications.

Size and Strain of Zinc Sulfide Nanoparticles Altered by Interaction with Organic Molecules.

Nanosized zinc sulfides (nano-ZnS) have size-dependent and tunable physical and chemical properties that make them useful for a variety of technological applications. For example, structural changes, especially caused by strain, are pronounced in nano-ZnS < 5 nm in size, the size range typical of incidental nano-ZnS that form in the environment. Previous research has shown how natural organic matter impacts the physical properties of nano-ZnS but was mostly focused on their aggregation state. However, the specific organic molecules and the type of functional groups that are most important for controlling the nano-ZnS size and strain remain unclear. This study examined the size-dependent strain of nano-ZnS synthesized in the presence of serine, cysteine, glutathione, histidine, and acetate. Synchrotron total scattering pair distribution function analysis was used to determine the average crystallite size and strain. Among the different organic molecules tested, those containing a thiol group were shown to affect the particle size and size-induced strain most strongly when added during synthesis but significantly reduced the particle strain when added to as-formed nano-ZnS. The same effects are useful to understand the properties and behavior of natural nano-ZnS formed as products of microbial activity, for example, in reducing environments, or of incidental nano-ZnS formed in organic wastes.

Selenium Nanowire Formation by Reacting Selenate with Magnetite.

The mobility of 79Se, a fission product of 235U and long-lived radioisotope, is an important parameter in the safety assessment of radioactive nuclear waste disposal systems. Nonradioactive selenium is also an important contaminant of drainage waters from black shale mountains and coal mines. Highly mobile and soluble in its high oxidation states, selenate (Se(VI)O42-) and selenite (Se(IV)O32-) oxyanions can interact with magnetite, a mineral present in anoxic natural environments and in steel corrosion products, thereby being reduced and consequently immobilized by forming low-solubility solids. Here, we investigated the sorption and reduction capacity of synthetic nanomagnetite toward Se(VI) at neutral and acidic pH, under reducing, oxygen-free conditions. The additional presence of Fe(II)aq, released during magnetite dissolution at pH 5, has an effect on the reduction kinetics. X-ray absorption spectroscopy analyses revealed that, at pH 5, trigonal gray Se(0) formed and that sorbed Se(IV) complexes remained on the nanoparticle surface during longer reaction times. The Se(0) nanowires grew during the reaction, which points to a complex transport mechanism of reduced species or to active reduction sites at the tip of the Se(0) nanowires. The concomitant uptake of aqueous Fe(II) and Se(VI) ions is interpreted as a consequence of small pH oscillations that result from the Se(VI) reduction, leading to a re-adsorption of aqueous Fe(II) onto the magnetite, renewing its reducing capacity. This effect is not observed at pH 7, where we observed only the formation of Se(0) with slow kinetics due to the formation of an oxidized maghemite layer. This indicates that the presence of aqueous Fe(II) may be an important factor to be considered when examining the environmental reactivity of magnetite.

Influence of Silica Coatings on Magnetite-Catalyzed Selenium Reduction.

The reactivity of iron(II/III) oxide surfaces may be influenced by their interaction with silica, which is ubiquitous in aquatic systems. Understanding the structure-reactivity relationships of Si-coated mineral surfaces is necessary to describe the complex surface behavior of nanoscale iron oxides. Here, we use Si-adsorption isotherms and Fourier transform infrared spectroscopy to analyze the sorption and polymerization of silica on slightly oxidized magnetite nanoparticles (15% maghemite and 85% magnetite, i.e., ∼2 maghemite surface layers), showing that Si adsorption follows a Langmuir isotherm up to 2 mM dissolved Si, where surface polymerization occurs. Furthermore, the effects of silica surface coatings on the redox-catalytic ability of magnetite are analyzed using selenium as a molecular probe. The results show that for partially oxidized nanoparticles and even under different Si surface coverages, electron transfer is still occurring. The results indicate anion exchange between silicate and the sorbed SeIV and SeVI. X-ray absorption near-edge structure analyses of the reacted Se indicate the formation of a mixed selenite/Se0 surface phase. We conclude that neither partial oxidation nor silica surface coatings block the sorption and redox-catalytic properties of magnetite nanoparticles, a result with important implications to assess the reactivity of mixed-valence phases in environmental settings.

Selenite Sorption on Hydrated CEM-V/A Cement in the Presence of Steel Corrosion Products: Redox vs Nonredox Sorption.

Reinforced cementitious structures in nuclear waste repositories will act as barriers that limit the mobility of radionuclides (RNs) in case of eventual leakage. CEM-V/A cement, a ternary blended cement with blast furnace slag (BFS) and fly ash (FA), could be qualified and used in nuclear waste disposal. Chemical interactions between the cement and RNs are critical but not completely understood. Here, we combined wet chemistry methods, synchrotron-based X-ray techniques, and thermodynamic modeling to explore redox interactions and nonredox sorption processes in simulated steel-reinforced CEM-V/A hydration systems using selenite as a molecular probe. Among all of the steel corrosion products analyzed, only the addition of Fe0 can obviously enhance the reducing ability of cement toward selenite. In comparison, steel corrosion products showed stronger reducing power in the absence of cement hydrates. Selenium K-edge X-ray absorption spectroscopy (XAS) revealed that selenite immobilization mechanisms included nonredox inner-/outer-sphere complexations and reductive precipitations of FeSe and/or Se(0). Importantly, the hydrated pristine cement showed a good reducing ability, driven by ferrous phases and (bi)sulfides (as shown by sulfur K-edge XAS) originated from BFS and FA. The overall redox potential imposed by hydrated CEM-V/A was determined, hinting to a redox shift in underground cementitious structures.

Influence of Surface Compositions on the Reactivity of Pyrite toward Aqueous U(VI).

Pyrite plays a significant role in governing the mobility of toxic uranium in an anaerobic environment via an oxidation-reduction process occurring at the mineral-water interface, but the factors influencing the reaction kinetics remain poorly understood. In this study, natural pyrites with different impurities (Pb, As, and Si) and different surface pretreatments were used to react with aqueous U(VI) from pH ∼3.0 to ∼9.5. Both aqueous and solid results indicated that freshly crushed pyrites, which do have more surface Fe2+/Fe3+ and S2- sites that were generated from breakage of Fe(S)-S bonds during ball milling, exhibited a much stronger reactivity than those treated with acid washing. Besides, U(VI) reduction which involves the possible intermediate U(V) and the formation of hyperstoichiometric UO2+x(s) was found to preferentially occur at Pb- and As-rich spots on the pyrite surface, suggesting that the incorporated impurities could act as reactive sites because of the generation of lattice defects and galena- and arsenopyrite-like local configurations. These reactive surface sites can be removed by acid washing, leaving a pyrite surface nearly inert toward aqueous U(VI). Thus, reactivity of pyrite toward U(VI) is largely governed by its surface compositions, which provides an insight into the chemical behavior of both pyrite and uranium in various environments.

In operando evidence of deoxygenation in ionic liquid gating of YBa2Cu3O7-X.

Field-effect experiments on cuprates using ionic liquids have enabled the exploration of their rich phase diagrams [Leng X, et al. (2011) Phys Rev Lett 107(2):027001]. Conventional understanding of the electrostatic doping is in terms of modifications of the charge density to screen the electric field generated at the double layer. However, it has been recently reported that the suppression of the metal to insulator transition induced in VO2 by ionic liquid gating is due to oxygen vacancy formation rather than to electrostatic doping [Jeong J, et al. (2013) Science 339(6126):1402-1405]. These results underscore the debate on the true nature, electrostatic vs. electrochemical, of the doping of cuprates with ionic liquids. Here, we address the doping mechanism of the high-temperature superconductor YBa2Cu3O7-X (YBCO) by simultaneous ionic liquid gating and X-ray absorption experiments. Pronounced spectral changes are observed at the Cu K-edge concomitant with the superconductor-to-insulator transition, evidencing modification of the Cu coordination resulting from the deoxygenation of the CuO chains, as confirmed by first-principles density functional theory (DFT) simulations. Beyond providing evidence of the importance of chemical doping in electric double-layer (EDL) gating experiments with superconducting cuprates, our work shows that interfacing correlated oxides with ionic liquids enables a delicate control of oxygen content, paving the way to novel electrochemical concepts in future oxide electronics.

Solid and Aqueous Speciation of Yttrium in Passive Remediation Systems of Acid Mine Drainage.

Yttrium belongs to the rare earth elements (REEs) together with lanthanides and scandium. REEs are commonly used in modern technologies, and their limited supply has made it necessary to look for new alternative resources. Acid mine drainage (AMD) is a potential resource since it is moderately enriched in REEs. In fact, in passive remediation systems, which are implemented to minimize the environmental impacts of AMD, REEs are mainly retained in basaluminite, an aluminum hydroxysulfate precipitate. In this study, the solid and liquid speciation and the local structure of yttrium are studied in high-sulfate aqueous solutions, basaluminite standards, and samples from remediation columns using synchrotron-based techniques and molecular modeling. Pair distribution function (PDF) analyses and ab initio molecular dynamics density functional theory models of the yttrium sulfate solution show that the YSO4+ ion pair forms a monodentate inner-sphere complex. Extended X-ray absorption fine structure (EXAFS) and PDF analyses show that Y is retained by basaluminite, forming a monodentate inner-sphere surface complex on the aluminum hydroxide surface. EXAFS of the column samples shows that more than 72% of their signal is represented by the signal of basaluminite with which YSO4+ forms an inner-sphere complex. The atomic view of the REE configuration in AMD environments could facilitate a deeper research of REE recovery from waste generated in AMD remediation systems.

XANES-Based Determination of Redox Potentials Imposed by Steel Corrosion Products in Cement-Based Media.

The redox potential (Eh) in a cementitious nuclear waste repository is critical to the retardation behavior of redox-sensitive radionuclides (RNs), and largely controlled by embedded steel corrosion but hard to be determined experimentally. Here, we propose an innovative Eh determination method based on chemical/spectroscopic measurements. Oxidized nuclides (UVI, SeIV, MoVI, and SbV) were employed as species probes to detect the Eh values imposed by steel (Fe0) and steel corrosion products (magnetite/hematite, and magnetite/goethite couples) in cement pore water. Nuclides showed good sorption affinity, especially toward Fe0, in decreasing Kd order for U > Sb > Se > Mo under both N2 and H2 atmospheres. The reduced nuclide species were identified as UO2, U4O9, FeSe, FeSe2, Se0, Sb0, and Sb2O3, but no redox transformation occurred for Mo. Eh values were obtained by using the Nernst equation. Remarkably, their values fell in a small range centered around -456 mV at pH ∼ 13.5 for both Fe0 and Fe-oxyhydroxides couples. This Eh value appears to be controlled by the nanocrystalline Fe(OH)2/Fe(OH)3 or (Fe1- x,Ca x)(OH)2/Fe(OH)3 couple, whose presence was confirmed by pair distribution function analyses. This approach could pave the way for describing the Eh gradient in reinforced concrete where traditional Eh measurements are not feasible.

Selenite Uptake by Ca-Al LDH: A Description of Intercalated Anion Coordination Geometries.

Layered double hydroxides (LDHs) are anion exchangers with a strong potential to scavenge anionic contaminants in aquatic environments. Here, the uptake of selenite (SeO32-) by Ca-Al LDHs was investigated as a function of Se concentration. Thermodynamic modeling of batch sorption isotherms shows that the formation of SeO32--intercalated AFm (hydrated calcium aluminate monosubstituent) phase, AFm-SeO3, is the dominant mechanism controlling the retention of Se at medium loadings. AFm-Cl2 shows much stronger affinity and larger distribution ratio (Rd ∼ 17800 L kg-1) toward SeO32- than AFm-SO4 (Rd ∼ 705 L kg-1). At stoichiometric SeO32- loading for anion exchange, the newly formed AFm-SeO3 phase results in two basal spacing, i.e., 9.93 ± 0.06 Å and ∼11.03 ± 0.03 Å. Extended X-ray absorption fine structure (EXAFS) spectra indicate that the intercalated SeO32- forms inner-sphere complexes with the Ca-Al-O layers. In situ X-ray diffraction (XRD) shows that basal spacing of Ca-Al LDHs have a remarkable linear relationship with the size of hydrated intercalated anions (i.e., Cl-, SO42-, MoO42-, and SeO32-). Contrary to AFm-SeO3 with inner-sphere SeO32- complexes in the interlayer, the phase with hydrogen-bonded inner-sphere complexed SeO32- is kinetically favored but thermodynamically unstable. This work offers new insights about the determination of intercalated anion coordination geometries via XRD analyses.

"On demand" triggered crystallization of CaCO3 from solute precursor species stabilized by the water-in-oil microemulsion.

Can we control the crystallization of solid CaCO3 from supersaturated aqueous solutions and thus mimic a natural process predicted to occur in living organisms that produce biominerals? Here we show how we achieved this by confining the reaction between Ca2+ and CO32- ions to the environment of nanosized water cores of water-in-oil microemulsions, in which the reaction between the ions is controlled by the intermicellar exchange processes. Using a combination of in situ small-angle X-ray scattering, high-energy X-ray diffraction, and low-dose liquid-cell scanning transmission electron microscopy, we elucidate how the presence of micellar interfaces leads to the formation of a solute CaCO3 phase/species that can be stabilized for extended periods of time inside micellar water nano-droplets. The nucleation and growth of any solid CaCO3 polymorph, including the amorphous phase, from such nano-droplets is prevented despite the fact that the water cores in the used microemulsion are highly supersaturated with respect to all known calcium carbonate solid phases. On the other hand the presence of the solute CaCO3 phase inside of the water cores decreases the rigidity of the micellar surfactant/water interface, which promotes the aggregation of micelles and the formation of large (>2 µm in diameter) globules. The actual precipitation and crystallization of solid CaCO3 could be triggered "on-demand" through the targeted removal of the organic-inorganic interface and hence the destabilization of globules carrying the CaCO3 solute.

Linear topology in amorphous metal oxide electrochromic networks obtained via low-temperature solution processing.

Amorphous transition metal oxides are recognized as leading candidates for electrochromic window coatings that can dynamically modulate solar irradiation and improve building energy efficiency. However, their thin films are normally prepared by energy-intensive sputtering techniques or high-temperature solution methods, which increase manufacturing cost and complexity. Here, we report on a room-temperature solution process to fabricate electrochromic films of niobium oxide glass (NbOx) and 'nanocrystal-in-glass' composites (that is, tin-doped indium oxide (ITO) nanocrystals embedded in NbOx glass) via acid-catalysed condensation of polyniobate clusters. A combination of X-ray scattering and spectroscopic characterization with complementary simulations reveals that this strategy leads to a unique one-dimensional chain-like NbOx structure, which significantly enhances the electrochromic performance, compared to a typical three-dimensional NbOx network obtained from conventional high-temperature thermal processing. In addition, we show how self-assembled ITO-in-NbOx composite films can be successfully integrated into high-performance flexible electrochromic devices.

Arsenate and Selenate Scavenging by Basaluminite: Insights into the Reactivity of Aluminum Phases in Acid Mine Drainage.

Basaluminite precipitation may play an important role in the behavior of trace elements in water and sediments affected by acid mine drainage and acid sulfate soils. In this study, the affinity of basaluminite and schwertmannite for arsenate and selenate is compared, and the coordination geometries of these oxyanions in both structures are reported. Batch isotherm experiments were conducted to examine the sorption capacity of synthetic schwertmannite and basaluminite and the potential competitive effect of sulfate. In addition, synchrotron-based techniques such as differential pair distribution function (d-PDF) analysis and extended X-ray absorption fine structure (EXAFS) were used to determine the local structure of As(V) and Se(VI) complexes. The results show that oxyanion exchange with structural sulfate was the main mechanism for removal of selenate, whereas arsenate was removed by a combination of surface complexes and oxyanion exchange. The arsenate adsorption capacity of basaluminite was 2 times higher than that of schwertmannite and 3 times higher than that of selenate in both phases. The sulfate:arsenate and sulfate:selenate exchange ratios were 1:2 and 1:1, respectively. High sulfate concentrations in the solutions did not show a competitive effect on arsenate sorption capacity but had a strong impact on selenate uptake, suggesting some kind of specific interaction for arsenate. Both d-PDF and EXAFS results indicated that the bidentate binuclear inner sphere was the most probable type of ligand for arsenate on both phases and for selenate on schwertmannite, whereas selenate forms outer-sphere complexes in the aluminum octahedral interlayer of basaluminite. Overall, these results show a strong affinity of poorly crystalline aluminum phases such as basaluminite for As(V) and Se(VI) oxyanions, with adsorption capacities on the same order of magnitude as those of iron oxides. The results obtained in this study are relevant to the understanding of trace element behavior in environments affected by acid water, potentially opening new research lines focused on remediation by natural attenuation processes or engineered water treatment systems.

Evidence of Multiple Sorption Modes in Layered Double Hydroxides Using Mo As Structural Probe.

Layered double hydroxides (LDHs) have been considered as effective phases for the remediation of aquatic environments, to remove anionic contaminants mainly through anion exchange mechanisms. Here, a combination of batch isotherm experiments and X-ray techniques was used to examine molybdate (MoO42-) sorption mechanisms on CaAl LDHs with increasing loadings of molybdate. Advanced modeling of aqueous data shows that the sorption isotherm can be interpreted by three retention mechanisms, including two types of edge sites complexes, interlayer anion exchange, and CaMoO4 precipitation. Meanwhile, Mo geometry evolves from tetrahedral to octahedral on the edge, and back to tetrahedral coordination at higher Mo loadings, indicated by Mo K-edge X-ray absorption spectra. Moreover, an anion exchange process on both CaAl LDHs was followed by in situ time-resolved synchrotron-based X-ray diffraction, remarkably agreeing with the sorption isotherm. This detailed molecular view shows that different uptake mechanisms-edge sorption, interfacial dissolution-reprecipitation-are at play and control anion uptake under environmentally relevant conditions, which is contrast to the classical view of anion exchange as the primary retention mechanism. This work puts all these mechanisms in perspective, offering a new insight into the complex interplay of anion uptake mechanisms by LDH phases, by using changes in Mo geometry as powerful molecular-scale probe.

Heterogeneous Nucleation and Growth of Barium Sulfate at Organic-Water Interfaces: Interplay between Surface Hydrophobicity and Ba(2+) Adsorption.

Barium sulfate (BaSO4) is a common scale-forming mineral in natural and engineered systems, yet the rates and mechanisms of heterogeneous BaSO4 nucleation are not understood. To address these, we created idealized interfaces on which to study heterogeneous nucleation rates and mechanisms, which also are good models for organic-water interfaces: self-assembled thin films terminated with different functional groups (i.e., -COOH, -SH, or mixed -SH & COOH) coated on glass slides. BaSO4 precipitation on coatings from Barite-supersaturated solutions (saturation index, SI, = 1.1) was investigated using grazing-incidence small-angle X-ray scattering. After reaction for 1 h, a little amount of BaSO4 formed on hydrophilic bare and -COOH coated glasses. Meanwhile, BaSO4 nucleation was significantly promoted on hydrophobic -SH and mixed -SH & COOH coatings. This is because substrate hydrophobicity likely affected the interfacial energy and hence thermodynamic favorability of heterogeneous nucleation. The heterogeneous BaSO4 nucleation and growth kinetics were found to be affected by the amount of Ba(2+) adsorption onto the substrate and incipient BaSO4 nuclei. The importance of Ba(2+) adsorption was further corroborated by the finding that precipitation rate increased under [Ba(2+)]/[SO4(2-)] concentration ratios >1. These observations suggest that thermodynamic favorability for nucleation is governed by substrate-water interfacial energy, while given favorable thermodynamics, the rate is governed by ion attachment to substrates and incipient nuclei.

Recovery of Rare Earth Elements and Yttrium from Passive-Remediation Systems of Acid Mine Drainage.

Rare earth elements and yttrium (REY) are raw materials of increasing importance for modern technologies, and finding new sources has become a pressing need. Acid mine drainage (AMD) is commonly considered an environmental pollution issue. However, REY concentrations in AMD can be several orders of magnitude higher than in naturally occurring water bodies. With respect to shale standards, the REY distribution pattern in AMD is enriched in intermediate and valuable REY, such as Tb and Dy. The objective of the present work is to study the behavior of REY in AMD passive-remediation systems. Traditional AMD passive remediation systems are based on the reaction of AMD with calcite-based permeable substrates followed by decantation ponds. Experiments with two columns simulating AMD treatment demonstrate that schwertmannite does not accumulate REY, which, instead, are retained in the basaluminite residue. The same observation is made in two field-scale treatments from the Iberian Pyrite Belt (IPB, southwest Spain). On the basis of the amplitude of this process and on the extent of the IPB, our findings suggest that the proposed AMD remediation process can represent a modest but suitable REY source. In this sense, the IPB could function as a giant heap-leaching process of regional scale in which rain and oxygen act as natural driving forces with no energy investment. In addition to having environmental benefits of its treatment, AMD is expected to last for hundreds of years, and therefore, the total reserves are practically unlimited.

Fate of Ag-NPs in Sewage Sludge after Application on Agricultural Soils.

The objective of this work was to investigate the fate of silver nanoparticles (Ag-NPs) in a sludge-amended soil cultivated with monocot (Wheat) and dicot (Rape) crop species. A pot experiment was performed with sludges produced in a pilot wastewater treatment plant containing realistic Ag concentrations (18 and 400 mg kg(-1), 14 mg kg(-1) for the control). Investigations focused on the highest dose treatment. X-ray absorption spectroscopy (XAS) showed that Ag2S was the main species in the sludge and amended soil before and after plant culture. The second most abundant species was an organic and/or amorphous Ag-S phase whose proportion slightly varied (from 24% to 36%) depending on the conditions. Micro and nano X-ray fluorescence (XRF) showed that Ag was preferentially associated with S-rich particles, including organic fragments, of the sludge and amended soils. Ag was distributed as heteroaggregates with soil components (size ranging from ≤0.5 to 1-3 µm) and as diffused zones likely corresponding to sorbed/complexed Ag species. Nano-XRF evidenced the presence of mixed metallic sulfides. Ag was weakly exchangeable and labile. However, micronutrient mobilization by plant roots and organic matter turnover may induce Ag species interconversion eventually leading to Ag release on longer time scales. Together, these data provide valuable information for risk assessment of sewage sludge application on agricultural soils.

Cryptomelane formation from nanocrystalline vernadite precursor: a high energy X-ray scattering and transmission electron microscopy perspective on reaction mechanisms.

BACKGROUND: Vernadite is a nanocrystalline and turbostratic phyllomanganate which is ubiquitous in the environment. Its layers are built of (MnO6)(8-) octahedra connected through their edges and frequently contain vacancies and  (or) isomorphic substitutions. Both create a layer charge deficit that can exceed 1 valence unit per layer octahedron and thus induces a strong chemical reactivity. In addition, vernadite has a high affinity for many trace elements (e.g., Co, Ni, and Zn) and possesses a redox potential that allows for the oxidation of redox-sensitive elements (e.g., As, Cr, Tl). As a result, vernadite acts as a sink for many trace metal elements. In the environment, vernadite is often found associated with tectomanganates (e.g., todorokite and cryptomelane) of which it is thought to be the precursor. The transformation mechanism is not yet fully understood however and the fate of metals initially contained in vernadite structure during this transformation is still debated. In the present work, the transformation of synthetic vernadite (δ-MnO2) to synthetic cryptomelane under conditions analogous to those prevailing in soils (dry state, room temperature and ambient pressure, in the dark) and over a time scale of ~10 years was monitored using high-energy X-ray scattering (with both Bragg-rod and pair distribution function formalisms) and transmission electron microscopy. RESULTS: Migration of Mn(3+) from layer to interlayer to release strains and their subsequent sorption above newly formed vacancy in a triple-corner sharing configuration initiate the reaction. Reaction proceeds with preferential growth to form needle-like crystals that subsequently aggregate. Finally, the resulting lath-shaped crystals stack, with n × 120° (n = 1 or 2) rotations between crystals. Resulting cryptomelane crystal sizes are ~50-150 nm in the ab plane and ~10-50 nm along c*, that is a tenfold increase compared to fresh samples. CONCLUSION: The presently observed transformation mechanism is analogous to that observed in other studies that used higher temperatures and (or) pressure, and resulting tectomanganate crystals have a number of morphological characteristics similar to natural ones. This pleads for the relevance of the proposed mechanism to environmental conditions.

Interfacial energies for heterogeneous nucleation of calcium carbonate on mica and quartz.

Interfacial free energies often control heterogeneous nucleation of calcium carbonate (CaCO3) on mineral surfaces. Here we report an in situ experimental study of CaCO3 nucleation on mica (muscovite) and quartz, which allows us to obtain the interfacial energies governing heterogeneous nucleation. In situ grazing incidence small-angle X-ray scattering (GISAXS) was used to measure nucleation rates at different supersaturations. The rates were incorporated into classical nucleation theory to calculate the effective interfacial energies (α'). Ex situ Raman spectroscopy identified both calcite and vaterite as CaCO3 polymorphs; however, vaterite is the most probable heterogeneous nuclei mineral phase. The α' was 24 mJ/m(2) for the vaterite-mica system and 32 mJ/m(2) for the vaterite-quartz system. The smaller α' of the CaCO3-mica system led to smaller particles and often higher particle densities on mica. A contributing factor affecting α' in our system was the smaller structural mismatch between CaCO3 and mica compared to that between CaCO3 and quartz. The extent of hydrophilicity and the surface charge could not explain the observed CaCO3 nucleation trend on mica and quartz. The findings of this study provide new thermodynamic parameters for subsurface reactive transport modeling and contribute to our understanding of mechanisms where CaCO3 formation on surfaces is of concern.

Pore-size-dependent calcium carbonate precipitation controlled by surface chemistry.

Induced mineral precipitation is potentially important for the remediation of contaminants, such as during mineral trapping during carbon or toxic metal sequestration. The prediction of precipitation reactions is complicated by the porous nature of rocks and soils and their interaction with the precipitate, introducing transport and confinement effects. Here X-ray scattering measurements, modeling, and electron microscopies were used to measure the kinetics of calcium carbonate precipitation in a porous amorphous silica (CPG) that contained two discrete distributions of pore sizes: nanopores and macropores. To examine the role of the favorability of interaction between the substrate and precipitate, some of the CPG was functionalized with a self-assembled monolayer (SAM) similar to those known to enhance nucleation densities on planar substrates. Precipitation was found to occur exclusively in macropores in the native CPG, while simultaneous precipitation in nanopores and macropores was observed in the functionalized CPG. The rate of precipitation in the nanopores estimated from the model of the X-ray scattering matched that measured on calcite single crystals. These results suggest that the pore-size distribution in which a precipitation reaction preferentially occurs depends on the favorability of interaction between substrate and precipitate, something not considered in most studies of precipitation in porous media.