Thermal Conductivity of ß-Phase Ga2O3 and (AlxGa1-x)2O3 Heteroepitaxial Thin Films.

Heteroepitaxy of ß-phase gallium oxide (ß-Ga2O3) thin films on foreign substrates shows promise for the development of next-generation deep ultraviolet solar blind photodetectors and power electronic devices. In this work, the influences of the film thickness and crystallinity on the thermal conductivity of (2̅01)-oriented ß-Ga2O3 heteroepitaxial thin films were investigated. Unintentionally doped ß-Ga2O3 thin films were grown on c-plane sapphire substrates with off-axis angles of 0° and 6° toward ⟨112̅0⟩ via metal-organic vapor phase epitaxy (MOVPE) and low-pressure chemical vapor deposition. The surface morphology and crystal quality of the ß-Ga2O3 thin films were characterized using scanning electron microscopy, X-ray diffraction, and Raman spectroscopy. The thermal conductivities of the ß-Ga2O3 films were measured via time-domain thermoreflectance. The interface quality was studied using scanning transmission electron microscopy. The measured thermal conductivities of the submicron-thick ß-Ga2O3 thin films were relatively low as compared to the intrinsic bulk value. The measured thin film thermal conductivities were compared with the Debye-Callaway model incorporating phononic parameters derived from first-principles calculations. The comparison suggests that the reduction in the thin film thermal conductivity can be partially attributed to the enhanced phonon-boundary scattering when the film thickness decreases. They were found to be a strong function of not only the layer thickness but also the film quality, resulting from growth on substrates with different offcut angles. Growth of ß-Ga2O3 films on 6° offcut sapphire substrates was found to result in higher crystallinity and thermal conductivity than films grown on on-axis c-plane sapphire. However, the ß-Ga2O3 films grown on 6° offcut sapphire exhibit a lower thermal boundary conductance at the ß-Ga2O3/sapphire heterointerface. In addition, the thermal conductivity of MOVPE-grown (2̅01)-oriented ß-(AlxGa1-x)2O3 thin films with Al compositions ranging from 2% to 43% was characterized. Because of phonon-alloy disorder scattering, the ß-(AlxGa1-x)2O3 films exhibit lower thermal conductivities (2.8-4.7 W/m·K) than the ß-Ga2O3 thin films. The dominance of the alloy disorder scattering in ß-(AlxGa1-x)2O3 is further evidenced by the weak temperature dependence of the thermal conductivity. This work provides fundamental insight into the physical interactions that govern phonon transport within heteroepitaxially grown ß-phase Ga2O3 and (AlxGa1-x)2O3 thin films and lays the groundwork for the thermal modeling and design of ß-Ga2O3 electronic and optoelectronic devices.

Ga2O3-on-SiC Composite Wafer for Thermal Management of Ultrawide Bandgap Electronics.

ß-phase gallium oxide (Ga2O3) is an emerging ultrawide bandgap (UWBG) semiconductor (EG ∼ 4.8 eV), which promises generational improvements in the performance and manufacturing cost over today's commercial wide bandgap power electronics based on GaN and SiC. However, overheating has been identified as a major bottleneck to the performance and commercialization of Ga2O3 device technologies. In this work, a novel Ga2O3/4H-SiC composite wafer with high heat transfer performance and an epi-ready surface finish has been developed using a fusion-bonding method. By taking advantage of low-temperature metalorganic vapor phase epitaxy, a Ga2O3 epitaxial layer was successfully grown on the composite wafer while maintaining the structural integrity of the composite wafer without causing interface damage. An atomically smooth homoepitaxial film with a room-temperature Hall mobility of ∼94 cm2/Vs and a volume charge of ∼3 × 1017 cm-3 was achieved at a growth temperature of 600 °C. Phonon transport across the Ga2O3/4H-SiC interface has been studied using frequency-domain thermoreflectance and a differential steady-state thermoreflectance approach. Scanning transmission electron microscopy analysis suggests that phonon transport across the Ga2O3/4H-SiC interface is dominated by the thickness of the SiNx bonding layer and an unintentionally formed SiOx interlayer. Extrinsic effects that impact the thermal conductivity of the 6.5 µm thick Ga2O3 layer were studied via time-domain thermoreflectance. Thermal simulation was performed to estimate the improvement of the thermal performance of a hypothetical single-finger Ga2O3 metal-semiconductor field-effect transistor fabricated on the composite substrate. This novel power transistor topology resulted in a ∼4.3× reduction in the junction-to-package device thermal resistance. Furthermore, an even more pronounced cooling effect is demonstrated when the composite wafer is implemented into the device design of practical multifinger devices. These innovations in device-level thermal management give promise to the full exploitation of the promising benefits of the UWBG material, which will lead to significant improvements in the power density and efficiency of power electronics over current state-of-the-art commercial devices.

Thermal Conductivity of Aluminum Scandium Nitride for 5G Mobile Applications and Beyond.

Radio frequency (RF) microelectromechanical systems (MEMS) based on Al1-xScxN are replacing AlN-based devices because of their higher achievable bandwidths, suitable for the fifth-generation (5G) mobile network. However, overheating of Al1-xScxN film bulk acoustic resonators (FBARs) used in RF MEMS filters limits power handling and thus the phone's ability to operate in an increasingly congested RF environment while maintaining its maximum data transmission rate. In this work, the ramifications of tailoring of the piezoelectric response and microstructure of Al1-xScxN films on the thermal transport have been studied. The thermal conductivity of Al1-xScxN films (3-8 W m-1 K-1) grown by reactive sputter deposition was found to be orders of magnitude lower than that for c-axis-textured AlN films due to alloying effects. The film thickness dependence of the thermal conductivity suggests that higher frequency FBAR structures may suffer from limited power handling due to exacerbated overheating concerns. The reduction of the abnormally oriented grain (AOG) density was found to have a modest effect on the measured thermal conductivity. However, the use of low AOG density films resulted in lower insertion loss and thus less power dissipated within the resonator, which will lead to an overall enhancement of the device thermal performance.