Survey of oligoethylene glycol-based self-assembled monolayers on electrochemical aptamer-based sensor in biological fluids.

The ability to monitor levels of endogenous markers and clearance profiles of drugs and their metabolites can improve the quality of biomedical research and precision with which therapies are individualized. Towards this end, electrochemical aptamer-based (EAB) sensors have been developed that support the real-time monitoring of specific analytes in vivo with clinically relevant specificity and sensitivity. A challenge associated with the in vivo deployment of EAB sensors, however, is how to manage the signal drift which, although correctable, ultimately leads to unacceptably low signal-to-noise ratios, limiting the measurement duration. Motivated by the correction of signal drift, in this paper, we have explored the use of oligoethylene glycol (OEG), a widely employed antifouling coating, to reduce the signal drift in EAB sensors. Counter to expectations, however, when challenged in 37 °C whole blood in vitro, EAB sensors employing OEG-modified self-assembled monolayers exhibit both greater drift and reduced signal gain, compared with those employ a simple, hydroxyl-terminated monolayer. On the other hand, when EAB sensor was prepared with a mix monolayer using MCH and lipoamido OEG 2 alcohol, reduced signal noise was observed compared to the same sensor prepared with MCH presumably due to improved SAM construction. These results suggest broader exploration of antifouling materials will be required to improve the signal drift of EAB sensors.

Molecularly Imprinted Polymer-Based Sensors for the Detection of Skeletal- and Cardiac-Muscle-Related Analytes.

Molecularly imprinted polymers (MIPs) are synthetic polymers with specific binding sites that present high affinity and spatial and chemical complementarities to a targeted analyte. They mimic the molecular recognition seen naturally in the antibody/antigen complementarity. Because of their specificity, MIPs can be included in sensors as a recognition element coupled to a transducer part that converts the interaction of MIP/analyte into a quantifiable signal. Such sensors have important applications in the biomedical field in diagnosis and drug discovery, and are a necessary complement of tissue engineering for analyzing the functionalities of the engineered tissues. Therefore, in this review, we provide an overview of MIP sensors that have been used for the detection of skeletal- and cardiac-muscle-related analytes. We organized this review by targeted analytes in alphabetical order. Thus, after an introduction to the fabrication of MIPs, we highlight different types of MIP sensors with an emphasis on recent works and show their great diversity, their fabrication, their linear range for a given analyte, their limit of detection (LOD), specificity, and reproducibility. We conclude the review with future developments and perspectives.

Ultrathin and Stretchable Rechargeable Devices with Organic Polymer Nanosheets Conformable to Skin Surface.

Ultrathin flexible electronic devices have been attracting substantial attention for biomonitoring, display, wireless communication, and many other ubiquitous applications. In this article, organic robust redox-active polymer/carbon nanotube hybrid nanosheets with thickness of just 100 nm are reported as power sources for ultrathin devices conformable to skin. Regardless of the extreme thinness of the electrodes, a moderately large current density of 0.4 mA cm-2 is achieved due to the high output of the polymers (>10 A g-1 ). For the first time, the use of mechanically robust yet intrinsically soft electrodes and polymer nanosheet sealing leads to the fabrication of rechargeable devices with only 1-µm thickness and even with stretchable properties.

3D Bioprinting in Skeletal Muscle Tissue Engineering.

Skeletal muscle tissue engineering (SMTE) aims at repairing defective skeletal muscles. Until now, numerous developments are made in SMTE; however, it is still challenging to recapitulate the complexity of muscles with current methods of fabrication. Here, after a brief description of the anatomy of skeletal muscle and a short state-of-the-art on developments made in SMTE with "conventional methods," the use of 3D bioprinting as a new tool for SMTE is in focus. The current bioprinting methods are discussed, and an overview of the bioink formulations and properties used in 3D bioprinting is provided. Finally, different advances made in SMTE by 3D bioprinting are highlighted, and future needs and a short perspective are provided.

On the injectability of free-standing magnetic nanofilms.

Free-standing films with sub-micrometric thickness, composed of soft polymers and functional nanostructures are promising candidates for many potential applications in the biomedical field, such as reduced port abdominal surgery. In this work, freely suspended poly(L-lactic acid) nanofilms with controlled morphology embedding superparamagnetic iron oxide nanoparticles were fabricated by spin-coating deposition. The mechanical properties of magnetic nanofilms were investigated by Strain-Induced Elastic Buckling Instability for Mechanical Measurements (SIEBIMM) test. Our results show that these freely suspended nanocomposite nanofilms are highly flexible and deformable, with Young's moduli of few GPa. Since they can be handled in liquid with syringes, a quantitative description of the nanofilms behavior during the manipulation with clinically applicable needles has been also provided. These magnetic nanofilms, remotely controllable by external electromagnetic fields, have potential applications in minimally invasive surgery as injectable nanopatches on inner organs wall. Graphical abstract ᅟ.

The efficacy of basic fibroblast growth factor-loaded poly(lactic-co-glycolic acid) nanosheet for mouse wound healing.

Although human recombinant basic fibroblast growth factor (bFGF) is widely used for wound healing, daily treatment with bFGF is required because of its short half-life. An effective controlled-release system of bFGF is, therefore, desired in clinical settings. To investigate the efficacy of a bFGF-loaded nanosheet for wound healing, focusing on the controlled-release of bFGF, bFGF-loaded poly(lactic-co-glycolic acid) (PGLA) nanosheets were developed, and their in vitro release profile of bFGF and their in vivo efficacy for wound healing were examined. A polyion complex of positively charged human recombinant bFGF and negatively charged alginate was sandwiched between PLGA nanosheets (70 nm thick for each layer). The resulting bFGF-loaded nanosheet robustly adhered to silicon skin by observation using a microscratch test. bFGF was gradually and continuously released over three days in an in vitro incubation study. Treatment with the bFGF-loaded nanosheets (every 3 day for 15 days) as well as with a conventional bFGF spray effectively promoted wound healing of mouse dorsal skin defects with accelerated tissue granulation and angiogenesis, although the dose of bFGF used in the treatment with the bFGF nanosheets was approximately 1/20 of the sprayed bFGF. In conclusion, we developed a bFGF-loaded nanosheet that sustained a continuous release of bFGF over three days and effectively promoted wound healing in mice.

Stretchable, adhesive and ultra-conformable elastomer thin films.

Thermoplastic elastomers are attractive materials because of the drastic changes in their physical properties above and below the glass transition temperature (Tg). In this paper, we report that free-standing polystyrene (PS, Tg: 100 °C) and polystyrene-polybutadiene-polystyrene triblock copolymer (SBS, Tg: -70 °C) thin films with a thickness of hundreds of nanometers were prepared by a gravure coating method. Among the mechanical properties of these thin films determined by bulge testing and tensile testing, the SBS thin films exhibited a much lower elastic modulus (ca. 0.045 GPa, 212 nm thickness) in comparison with the PS thin films (ca. 1.19 GPa, 217 nm thickness). The lower elastic modulus and lower thickness of the SBS thin films resulted in higher conformability and thus higher strength of adhesion to an uneven surface such as an artificial skin model with roughness (Ra = 10.6 µm), even though they both have similar surface energies. By analyzing the mechanical properties of the SBS thin films, the elastic modulus and thickness of the thin films were strongly correlated with their conformability to a rough surface, which thus led to a high adhesive strength. Therefore, the SBS thin films will be useful as coating layers for a variety of materials.

Engineered nanomembranes for directing cellular organization toward flexible biodevices.

Controlling the cellular microenvironment can be used to direct the cellular organization, thereby improving the function of synthetic tissues in biosensing, biorobotics, and regenerative medicine. In this study, we were inspired by the microstructure and biological properties of the extracellular matrix to develop freestanding ultrathin polymeric films (referred as "nanomembranes") that were flexible, cell adhesive, and had a morphologically tailorable surface. The resulting nanomembranes were exploited as flexible substrates on which cell-adhesive micropatterns were generated to align C2C12 skeletal myoblasts and embedded fibril carbon nanotubes enhanced the cellular elongation and differentiation. Functional nanomembranes with tunable morphology and mechanical properties hold great promise in studying cell-substrate interactions and in fabricating biomimetic constructs toward flexible biodevices.

UV laser-processed microstructure for building biohybrid actuators with anisotropic movement.

Fabrication of a biohybrid actuator requires muscle cells anisotropically aligned in a line, curve, or combination of lines and curves (similar to the microstructure of living muscle tissue) to replicate lifelike movements, in addition to considering the arrangement of skeletal structure or muscular structure with anisotropic straight patterns. Here, we report a UV laser-processed microstructure for freely directing cellular alignment to engineer a biohybrid actuator composed of poly(styrene-block-butadiene-block-styrene triblock copolymer) (SBS) thin film with tailor-made microgrooves (MGs) and skeletal myotubes aligned along these MGs. Specifically, straight, circular, or curved MGs were transferred to SBS thin films from a UV laser-processed template, allowing for the successful alignment of myotubes along MGs. The biohybrid actuator, composed of anisotropically aligned myotubes on a curved microgrooved SBS thin film, was contracted by electrical stimulation. Contraction of biohybrid actuators with curved aligned myotubes permits twisted-like behavior, unlike straight microgrooved films. Therefore, the UV laser-ablation system is a unique maskless and rapid microfabrication technique that provides intriguing opportunities for omni-directional microgrooved structures to achieve the complex motion of living organisms.

Ultraconformable Capacitive Strain Sensor Utilizing Network Structure of Single-Walled Carbon Nanotubes for Wireless Body Sensing.

Capture and real-time recording of precise body movements using strain sensors provide personal information for healthcare monitoring and management. To acquire this information, a sensor that conforms to curved irregular surfaces, including biological tissue, is desired to record complex body movements while acting like a second skin to avoid interference with the movements. In this study, we developed a thin-film-type capacitive strain sensor that is flexible and stretchable on the surface of a living body. We fabricated conductive polymeric ultrathin films ("nanosheets") comprising polystyrene-block-polybutadiene (SB) elastomers and single-walled carbon nanotubes (SWCNTs) (i.e., SWCNT-SB nanosheets) via gravure coating; the SWCNT-SB-coated nanosheets were used as the flexible electrode in a capacitive strain sensor. The dielectric (DE) layer was then prepared using the silicone elastomer Ecoflex 00-30 because its Young's modulus is comparable to that of the epidermis. The normalized capacitance changes (ΔC/C0) in the sensor increased with increasing tensile strain over a range from 0-100%, indicating that the proposed sensor can measure the strain of biological movements, including those of skin and blood vessels. To improve sensor conformability further, the effect of sensor thickness on the gauge factor (GF) was investigated using thinner DE layers by focusing on their flexural rigidity. As a result, the GF increased from 0.64 to 1.13 as the DE layer thickness decreased from 260 to 40 µm. Finally, we evaluated the fabricated sensor's signal stability and mechanical durability, including during wireless sensing when applied to human skin and a vascular model. The ΔC/C0 values varied in response to the bending motion of a finger, dilation of a blood vessel, and the swallowing movement of the throat. These results indicate that our capacitive strain sensor is conformable and functional on biological tissue to enable monitoring of dynamic biological movements (e.g., pulse rate and arterial dilation) without wearer discomfort.

An intrinsically semi-permeable PDMS nanosheet encapsulating adipose tissue-derived stem cells for enhanced angiogenesis.

Cell encapsulation devices are expected to be promising tools that can control the release of therapeutic proteins secreted from transplanted cells. The protein permeability of the device membrane is important because it allows the isolation of transplanted cells while enabling the effectiveness of the device. In this study, we investigated free-standing polymeric ultra-thin films (nanosheets) as an intrinsically semi-permeable membrane made from polydimethylsiloxane (PDMS). The PDMS nanosheet with a thickness of 600 nm showed intrinsic protein permeability, and the device fabricated with the PDMS nanosheet showed that VEGF secreted from implanted adipose tissue-derived stem cells (ASCs) could be released for at least 5 days. The ASC encapsulation device promoted angiogenesis and the development of granulation tissue 1 week after transplantation to the subcutaneous area of a mouse. This cell encapsulation device consisting of PDMS nanosheets provides a new method for pre-vascularization of the subcutaneous area in cell transplantation therapy.

Porous Polymeric Nanofilms for Recreating the Basement Membrane in an Endothelial Barrier-on-Chip.

Organs-on-chips (OoCs) support an organotypic human cell culture in vitro. Precise representation of basement membranes (BMs) is critical for mimicking physiological functions of tissue interfaces. Artificial membranes in polyester (PES) and polycarbonate (PC) commonly used in in vitro models and OoCs do not replicate the characteristics of the natural BMs, such as submicrometric thickness, selective permeability, and elasticity. This study introduces porous poly(d,l-lactic acid) (PDLLA) nanofilms for replicating BMs in in vitro models and demonstrates their integration into microfluidic chips. Using roll-to-roll gravure coating and polymer phase separation, we fabricated transparent ∼200 nm thick PDLLA films. These nanofilms are 60 times thinner and 27 times more elastic than PES membranes and show uniformly distributed pores of controlled diameter (0.4 to 1.6 µm), which favor cell compartmentalization and exchange of large water-soluble molecules. Human umbilical vein endothelial cells (HUVECs) on PDLLA nanofilms stretched across microchannels exhibited 97% viability, enhanced adhesion, and a higher proliferation rate compared to their performance on PES membranes and glass substrates. After 5 days of culture, HUVECs formed a functional barrier on suspended PDLLA nanofilms, confirmed by a more than 10-fold increase in transendothelial electrical resistance and blocked 150 kDa dextran diffusion. When integrated between two microfluidic channels and exposed to physiological shear stress, despite their ultrathin thickness, PDLLA nanofilms upheld their integrity and efficiently maintained separation of the channels. The successful formation of an adherent endothelium and the coculture of HUVECs and human astrocytes on either side of the suspended nanofilm validate it as an artificial BM for OoCs. Its submicrometric thickness guarantees intimate contact, a key feature to mimic the blood-brain barrier and to study paracrine signaling between the two cell types. In summary, porous PDLLA nanofilms hold the potential for improving the accuracy and physiological relevance of the OoC as in vitro models and drug discovery tools.

A combination of logical judging circuit and water-resistant ultrathin film PEDOT: PSS electrode for noninvasive ECG measurement.

Heart disease-related deaths have increased in recent decades, with most patients dying of sudden cardiac arrest. In such instances, the effect of regular electrocardiogram (ECG) measurements is minimal. Therefore, long-term ECG monitoring has become increasingly important. In this paper, we report a non-adhesive high accuracy ECG monitoring system that can be used in various scenarios without interfering with daily activities. The ECG ultra-thin film electrode is made by water-resistant material based on poly(3,4-ethylenedioxythiophene) poly(4-styrenesulfonate) (PEDOT: PSS) electrode doped with ethylene glycol (EG) and xylitol, to improve the noise signal caused by sweat. The optimal ratio of the three ingredients of PEDOT: PSS/xylitol/EG was determined experimentally to accommodate the ECG monitoring. By using the proposed selectively closed multi-channel single-lead logic circuit, the noise of ECG signal received from the proposed film electrode can be successfully reduced during broad-area electrode measurements, thus to improve ECG measurement accuracy.

Nanosheet Promotes Chronic Wound Healing by Localizing Uncultured Stromal Vascular Fraction Cells.

Objective: To develop an efficacious and efficient method for treating chronic wounds using "nanosheet" that improves the survival and localization of transplanted cells without prior seeding to optimally derive the regenerative potentials of uncultured stromal vascular fraction (SVF) cells. Approach: We propose a method whereby the wound is covered by uncultured SVF cells using the nanosheet [porous poly(d, l,-lactic acid)] (PDLLA) films) designed to hold cells in a single-cell layer. A chronic wound model was created on 12-month-old db/db mice by inflecting a full-thickness skin excision on their dorsum and was subsequently given either no treatment or a treatment with SVF cells alone (with Tegaderm dressing), nanosheet alone, or nanosheet with SVF cells. Results: The placement of the nanosheet improved the grafted cell retention rate at day 10 timepoint by 5 folds, and the wound area was the smallest in the wounds treated with SVF cells plus nanosheet in comparison to the other groups. Collagen deposition and epidermal growth factor were significantly higher in the wound beds treated with SVF cells with the nanosheet, offering some mechanistic insights. Innovation: Porous poly(d, l,-lactic acid acid) (PDLLA) films or "nanosheet" printed on the nanoscale (1-100 nm in thickness) as a cellular scaffold for cytotherapy for the treatment of chronic wounds. Conclusion: The use of the nanosheet is an effective way to improve the transplanted SVF cell retention and accelerate the overall wound closure.

Latest developments in engineered skeletal muscle tissues for drug discovery and development.

INTRODUCTION: With the advances in skeletal muscle tissue engineering, new platforms have arisen with important applications in biology studies, disease modeling, and drug testing. Current developments highlight the quest for engineering skeletal muscle tissues with higher complexity . These new human skeletal muscle tissue models will be powerful tools for drug discovery and development and disease modeling. AREAS COVERED: The authors review the latest advances in in vitro models of engineered skeletal muscle tissues used for testing drugs with a focus on the use of four main cell culture techniques: Cell cultures in well plates, in microfluidics, in organoids, and in bioprinted constructs. Additional information is provided on the satellite cell niche. EXPERT OPINION: In recent years, more sophisticated in vitro models of skeletal muscle tissues have been fabricated. Important developments have been made in stem cell research and in the engineering of human skeletal muscle tissue. Some platforms have already started to be used for drug testing, notably those based on the parameters of hypertrophy/atrophy and the contractibility of myotubes. More developments are expected through the use of multicellular types and multi-materials as matrices . The validation and use of these models in drug testing should now increase.

Bioprinting and biomaterials for dental alveolar tissue regeneration.

Three dimensional (3D) bioprinting is a powerful tool, that was recently applied to tissue engineering. This technique allows the precise deposition of cells encapsulated in supportive bioinks to fabricate complex scaffolds, which are used to repair targeted tissues. Here, we review the recent developments in the application of 3D bioprinting to dental tissue engineering. These tissues, including teeth, periodontal ligament, alveolar bones, and dental pulp, present cell types and mechanical properties with great heterogeneity, which is challenging to reproduce in vitro. After highlighting the different bioprinting methods used in regenerative dentistry, we reviewed the great variety of bioink formulations and their effects on cells, which have been established to support the development of these tissues. We discussed the different advances achieved in the fabrication of each dental tissue to provide an overview of the current state of the methods. We conclude with the remaining challenges and future needs.

Inkjet printing of protein microarrays on freestanding polymeric nanofilms for spatio-selective cell culture environment.

In the last years, an increasing interest in bio-hybrid systems for what concerns the precise control of cell-material interactions has emerged. This trend leads towards the development of new nano-structured devices such as bioMEMS, tissue-engineering scaffolds, biosensors, etc. In the present study, we focused on the development of a spatio-selective cell culture environment based on the inkjet printing of bio-patterns on polymeric ultra-thin films (nanofilms) composed of poly(methylmethacrylate) (PMMA). Freestanding PMMA nanofilms having hundreds-of-nm thickness were prepared by spin-coating. Different shapes of cell adhesion promoters such as poly (L-lysine) (PLL) were micropatterned by inkjet printing. Moreover, to promote cell adhesion, the surface of PLL microarrays was modified with fibronectin via electorostatic interaction. The selective deposition of C2C12 skeletal muscle cells was confirmed and their viability was qualitatively assessed after 24 h. The combination of muscular cells with protein micropatterned freestanding nanofilm is beneficial for the implementation of new bio-hybrid system in muscular tissue engineering.

An ultrathin poly(L-lactic acid) nanosheet as a burn wound dressing for protection against bacterial infection.

Burn wounds are highly susceptible to bacterial infection due to impairment of the skin's integrity. Therefore, prevention of bacterial colonization/infection in the wound is crucial for the management of burns, including partial-thickness burn injuries. Although partial-thickness burn injuries still retain the potential for reepithelialization, the complication of wound infection severely impairs the reepithelialization even in such superficial burn injuries. We recently developed a biocompatible nanosheet consisting of poly(L-lactic acid) (PLLA). The PLLA nanosheets have many useful and advantageous biological properties for their application as a wound dressing, such as sufficient flexibility, transparency, and adhesiveness. We herein investigated the suitability of the PLLA nanosheets as a wound dressing for partial-thickness burn wounds in mice. The PLLA nanosheets tightly adhered to the wound without any adhesive agents. Although wound infection with Pseudomonas aeruginosa in the controls significantly impaired reepithelialization of burn wounds, dressing with the PLLA nanosheet markedly protected against bacterial wound infection, thereby improving wound healing in the mice receiving partial-thickness burn injuries. The PLLA nanosheet also showed a potent barrier ability for protecting against bacterial penetration in vitro. The ultrathin PLLA nanosheet may be applied as a protective dressing to reduce environmental contamination of bacteria in a partial-thickness burn wound.

Angiogenic efficacy of ASC spheroids filtrated on porous nanosheets for the treatment of a diabetic skin ulcer.

Stem cell transplantation is expected to be an effective treatment for intractable skin ulcers by promoting angiogenesis; however, it is challenging to quickly realize a sufficient bloodstream for the ulcers. For this treatment, sheet-like materials with monolayer cells such as cell sheets have been investigated. However, they have a limitation of cell number that can be transplanted at one time due to the two-dimensional, monolayer cell structure, and sufficient secretion of growth factors cannot be expected. In this regard, cellular aggregates, such as spheroids, can reproduce three-dimensional cell-cell interactions that cause biological functions of living tissues more representative than monolayer cells, which is important to achieving efficient secretion of growth factors. In this study, we focused on free-standing porous polymer ultrathin films ("porous nanosheets") comprising poly(d,l-lactic acid) (PDLLA) and succeeded in developing a spheroid-covered nanosheet, on which more than 1000 spheroids from adipose-tissue derived stem cells (ASCs) were loaded. The porous structure with an average pore diameter of 4 µm allowed for facile filtration and carrying spheroids on the nanosheet, as well as sufficient oxygen and nutrients inflow to the cells. The spheroid-covered nanosheet achieved homogeneous transference of spheroids to a whole skin defect in diabetic model mice. Given the continuous release of vascular endothelial growth factor (VEGF) from the spheroids, the transplanted spheroids promoted healing with more accelerated angiogenesis than a nanosheet with a monolayer of cells. The spheroid-covered nanosheet may be a new regenerative material for promoting intractable skin ulcer healing.

Evaluation of substrata effect on cell adhesion properties using freestanding poly(L-lactic acid) nanosheets.

Investigation of the interactions between cells and material surfaces is important not only for the understanding of cell biology but also for the development of smart biomaterials. In this study, we investigated the substrate-related effects on the interaction between cell and polymeric ultrathin film (nanosheet) by modulating the mechanical properties of the nanosheet with a metal substrate or mesh. A freestanding polymeric nanosheet with tens-of-nanometers thickness composed of poly(L-lactic acid) (PLLA nanosheet) was fabricated by combination of a spin-coating technique and a water-soluble sacrificial layer. The freestanding PLLA nanosheet was collected on a stainless steel mesh (PLLA-mesh) and subsequently used for cell adhesion studies, comparing the results to the ones on a control SiO(2) substrate coated with an ultrathin layer of PLLA (PLLA-substrate). The adhesion of rat cardiomyocytes (H9c2) was evaluated on both samples after 24 h of culture. The PLLA-mesh with the tens-of-nanometers thick nanosheets induced an anisotropic adhesion of H9c2, while H9c2 on the PLLA-substrate showed an isotropic adhesion independent from the nanosheet thickness. Interestingly, an increment in the nanosheet thickness in the PLLA-mesh samples reduced the cellular anisotropy and led to a similar morphology to the PLLA-substrate. Considering the huge discrepancy of Young's modulus between PLLA nanosheet (3.5-4.2 GPa) and metal substrate (hundreds of GPa), cell adhesion was mechanically regulated by the Young's modulus of the underlying substrate when the thickness of the PLLA nanosheet was tens of nanometers. Modulation of the stiffness of the polymeric nanosheet by utilizing a rigid underlying material will allow the constitution of a unique cell culture environment.