Porosity Engineering of Dried Smart Poly(N-isopropylacrylamide) Hydrogels for Gas Sensing.

A recent study unveiled the potential of acrylamide-based stimulus-responsive hydrogels for volatile organic compound detection in gaseous environments. However, for gas sensing, a large surface area, that is, a highly porous material, offering many adsorption sites is crucial. The large humidity variation in the gaseous environment constitutes a significant challenge for preserving an initially porous structure, as the pores tend to be unstable and irreversibly collapse. Therefore, the present investigation focuses on enhancing the porosity of smart PNiPAAm hydrogels under the conditions of a gaseous environment and the preservation of the structural integrity for long-term use. We have studied the influence of polyethylene glycol (PEG) as a porogen and the application of different drying methods and posttreatment. The investigations lead to the conclusion that only the combination of PEG addition, freeze-drying, and subsequent conditioning in high relative humidity enables a long-term stable formation of a porous surface and inner structure of the material. The significantly enhanced swelling response in a gaseous environment and in the test gas acetone is confirmed by gravimetric experiments of bulk samples and continuous measurements of thin films on piezoresistive pressure sensor chips. These measurements are furthermore complemented by an in-depth analysis of the morphology and microstructure. While the study was conducted for PNiPAAm, the insights and developed processes are general in nature and can be applied for porosity engineering of other smart hydrogel materials for VOC detection in gaseous environments.

An Effective Method to Model and Simulate the Behavior of Inductive Angle Encoders.

Many angle or position sensors rank among the inductive encoders, although their sensing principle is different. The sensor design investigated in this paper is based on coupled coils, whereas the information about the position angle is modulated on the induced voltage, measured at the receiving coils. Unfortunately, no closed solution for most of the physical quantities exists, since this principle is based on eddy currents, which are rather complex to calculate for the given geometry. Consequently, the common way is to calculate the sensor quantities by a 3D finite-element (FE) simulation. However, this leads in most cases to a high time and computational effort. To overcome the limitations with respect to computational resources, a novel method is presented to reduce simulation effort and calculate regression models, which can even replace simulations. In the following investigations, D-optimal designs are used-a subdomain in the field of statistical design of experiments-and combined with a numerical implementation of Faraday's law, in order to calculate the induced voltages afterwards from simulated magnetic field data. With this method, the sensor signals can be calculated for multiple angle positions from one simulated position by shifting the integration boundaries. Hence, simulation time is significantly reduced for a full period. The regression models obtained by this method, can predict the Tx-coil inductance, induced Rx-voltage amplitude and angular error in dependency of geometric design parameters.

Link between Heterotrophic Carbon Fixation and Virulence in the Porcine Lung Pathogen Actinobacillus pleuropneumoniae.

Actinobacillus pleuropneumoniae is a capnophilic pathogen of the porcine respiratory tract lacking enzymes of the oxidative branch of the tricarboxylic acid (TCA) cycle. We previously claimed that A. pleuropneumoniae instead uses the reductive branch in order to generate energy and metabolites. Here, we show that bicarbonate and oxaloacetate supported anaerobic growth of A. pleuropneumoniae Isotope mass spectrometry revealed heterotrophic fixation of carbon from stable isotope-labeled bicarbonate by A. pleuropneumoniae, which was confirmed by nano-scale secondary ion mass spectrometry at a single-cell level. By gas chromatography-combustion-isotope ratio mass spectrometry we could further show that the labeled carbon atom is mainly incorporated into the amino acids aspartate and lysine, which are derived from the TCA metabolite oxaloacetate. We therefore suggest that carbon fixation occurs at the interface of glycolysis and the reductive branch of the TCA cycle. The heme precursor δ-aminolevulinic acid supported growth of A. pleuropneumoniae, similar to bicarbonate, implying that anaplerotic carbon fixation is needed for heme synthesis. However, deletion of potential carbon-fixing enzymes, including PEP-carboxylase (PEPC), PEP-carboxykinase (PEPCK), malic enzyme, and oxaloacetate decarboxylase, as well as various combinations thereof, did not affect carbon fixation. Interestingly, generation of a deletion mutant lacking all four enzymes was not possible, suggesting that carbon fixation in A. pleuropneumoniae is an essential metabolic pathway controlled by a redundant set of enzymes. A double deletion mutant lacking PEPC and PEPCK was not impaired in carbon fixation in vitro but showed reduction of virulence in a pig infection model.

Hydrogel-Based Sensors for Ethanol Detection in Alcoholic Beverages.

A fast and reliable determination of the ethanol concentration is essential in the analysis of alcoholic beverages. However, different factors like pH value or salt concentration can influence the ethanol measurement. Furthermore, analytical figures of merit for the alcohol sensor, such as limit of detection, sensitivity and measurement uncertainty, are necessary for the application. In this paper, a detailed sensor characterization of a novel sensor based on ethanol-sensitive poly acrylamide hydrogels will be presented. The resulting swelling pressure of the hydrogel was transformed via a piezoresistive pressure sensor into a measurable output voltage. These kinds of sensors can be used over a large measuring range, up to 50 vol% ethanol and more, with a high sensitivity. In the range from pH 7.4 to 4, the pH value had no influence on the sensor signal. Higher salt concentrations can slightly influence the measurement. The detection limit amounts to 0.06⁻0.65 vol% ethanol. The concentration of a vodka sample was determined with a sufficient measuring uncertainty.

Piezoresistive Hydrogel-Based Sensors for the Detection of Ammonia.

Ammonia is an essential key compound in the chemical industry. However, excessively high ammonia concentrations can be harmful to the environment. Sensors for the detection of ammonia are therefore particularly important for environmental analysis. In this article, a novel hydrogel-based piezoresistive ammonia sensor is presented. In aqueous solution, ammonia reacts as a base. This alkaline pH change can be detected with stimuli-sensitive hydrogels. For such an application, highly sensitive hydrogels in the alkaline range with sufficient mechanical stability for the sensor application has to be developed. These conditions are fulfilled by the presented hydrogel system based on acrylic acid (AAc) and 2-(dimethylamino)ethyl methacrylate (DMAEMA). The hydrogel composition has a significant influence on the swelling behavior of the gel. Furthermore, the hydrogel swelling in ammonia solutions was tested and a detection limit in the range of 1 mmol/L ammonia depending on the buffer solution was determined. Ammonia-sensitive hydrogels can be used multiple times due to the repeatable swelling of the gel over several swelling cycles. To generate a measurable output voltage, the swelling pressure of ammonia-sensitive hydrogels were detected by using piezoresistive pressure sensors. All results of the free hydrogel swelling were verified in the sensor application. This low-cost ammonia sensor with a high sensitivity could be interesting for industrial chemical and biotechnological applications.

Enzyme-Functionalized Piezoresistive Hydrogel Biosensors for the Detection of Urea.

Urea is used in a wide variety of industrial applications such as the production of fertilizers. Furthermore, urea as a metabolic product is an important indicator in biomedical diagnostics. For these applications, reliable urea sensors are essential. In this work, we present a novel hydrogel-based biosensor for the detection of urea. The hydrolysis of urea by the enzyme urease leads to an alkaline pH change, which is detected with a pH-sensitive poly(acrylic acid-co-dimethylaminoethyl methacrylate) hydrogel. For this purpose, the enzyme is physically entrapped during polymerization. This enzyme-hydrogel system shows a large sensitivity in the range from 1 mmol/L up to 20 mmol/L urea with a high long-term stability over at least eight weeks. Furthermore, this urea-sensitive hydrogel is highly selective to urea in comparison to similar species like thiourea or N-methylurea. For sensory applications, the swelling pressure of this hydrogel system is transformed via a piezoresistive pressure sensor into a measurable output voltage. In this way, the basic principle of hydrogel-based piezoresistive urea biosensors was demonstrated.

Hydrogel-Based Plasmonic Sensor Substrate for the Detection of Ethanol.

The in-line monitoring of ethanol concentration in liquids is a crucial part of process monitoring in breweries and distilleries. Current methods are based on infrared spectroscopy, which is time-consuming and costly, making these methods unaffordable for small and middle-sized companies. To overcome these problems, we presented a small, compact, and cost-effective sensing method for the ethanol content, based on a nanostructured, plasmonically active sensor substrate. The sensor substrate is coated with an ethanol-sensitive hydrogel, based on polyacrylamide and bisacrylamide, which induces a change in the refractive index of the substrate surface. The swelling and shrinking of such hydrogels offer a means to measure the ethanol content in liquids, which can be determined in a simple transmittance setup. In our study, we demonstrated the capability of the sensor principle for the detection of ethanol content ranging from 0 to 30 vol% ethanol. Furthermore, we determined the response time of the sensor substrate to be 5.2 min, which shows an improvement by a factor of four compared to other hydrogel-based sensing methods. Finally, initial results for the sensor's lifetime are presented.

Identification of QTL affecting resistance/susceptibility to acute Actinobacillus pleuropneumoniae infection in swine.

Actinobacillus pleuropneumoniae is among the most important pathogens worldwide in pig production. The agent can cause severe economic losses due to decreased performance, acute or chronic pleuropneumonia and an increased incidence of death. Therapeutics cannot be used in a sustainable manner, and vaccination is not always available, but discovering more about host defence and disease mechanisms might lead to new methods of prophylaxis. The aim of the present study was to detect quantitative trait loci (QTL) associated with resistance/susceptibility to A. pleuropneumoniae. Under controlled conditions, 170 F2 animals of a Hampshire/Landrace family, with known differences in founder populations regarding A. pleuropneumoniae resistance, were challenged with an A. pleuropneumoniae serotype 7 aerosol followed by a detailed clinical, radiographic, ultrasonographic, pathological and bacteriological examination. F2 pigs were genotyped with 159 microsatellite markers. Significant QTL were identified on Sus scrofa chromosomes (SSC) 2, 6, 12, 13, 16, 17 and 18. They explained 6-22% of phenotypic variance. One QTL on SSC2 reached significance on a genome-wide level for five associated phenotypic traits. A multiple regression analysis revealed a combinatory effect of markers SWR345 (SSC2) and S0143 (SSC12) on Respiratory Health Score, Clinical Score and the occurrence of death. The results indicate the genetic background of A. pleuropneumoniae resistance in swine and provide new insights into the genetic architecture of resistance/susceptibility to porcine pleuropneumonia. The results will be helpful in identifying the underlying genes and mechanisms.

Pathway deregulation and expression QTLs in response to Actinobacillus pleuropneumoniae infection in swine.

Actinobacillus (A.) pleuropneumoniae is among the most important pathogens in pig. The agent causes severe economic losses due to decreased performance, the occurrence of acute or chronic pleuropneumonia, and an increase in death incidence. Since therapeutics cannot be used in a sustainable manner, and vaccination is not always available, new prophylactic measures are urgently needed. Recent research has provided evidence for a genetic predisposition in susceptibility to A. pleuropneumoniae in a Hampshire × German Landrace F2 family with 170 animals. The aim of the present study is to characterize the expression response in this family in order to unravel resistance and susceptibility mechanisms and to prioritize candidate genes for future fine mapping approaches. F2 pigs differed distinctly in clinical, pathological, and microbiological parameters after challenge with A. pleuropneumoniae. We monitored genome-wide gene expression from the 50 most and 50 least susceptible F2 pigs and identified 171 genes differentially expressed between these extreme phenotypes. We combined expression QTL analyses with network analyses and functional characterization using gene set enrichment analysis and identified a functional hotspot on SSC13, including 55 eQTL. The integration of the different results provides a resource for candidate prioritization for fine mapping strategies, such as TF, TFRC, RUNX1, TCN1, HP, CD14, among others.

Facts, myths and hypotheses on the zoonotic nature of Mycobacterium avium subspecies paratuberculosis.

Mycobacterium avium subspecies paratuberculosis (MAP) is the causative agent of paratuberculosis (Johne's disease [JD]), a chronic granulomatous enteritis in ruminants. JD is one of the most widespread bacterial diseases of domestic animals with significant economic impact. The histopathological picture of JD resembles that of Crohn's disease (CD), a human chronic inflammatory bowel disease of still unresolved aetiology. An aetiological relevance of MAP for CD has been proposed. This and the ambiguity of other published epidemiological findings raise the question whether MAP represents a zoonotic agent. In this review, we will discuss evidence that MAP has zoonotic capacity.

Influence of Active-to-Passive Ratio on the Deformation in Circular Dielectric Elastomer Actuators.

To further improve the performance of dielectric elastomer actuaotrs (DEAs), the development of novel elastomers with enhanced electro-mechanical properties is focal for the advancement of the technology. Hence, reliable techniques to assess their electro-mechanical performance are necessary. Characterization of the actuator materials is often achieved by fabricating circular DEAs with the pre-stretch of the membrane fixed by a stiff frame. Because of this set-up, the electrode size relative to the carrier frame's dimension has an impact on actuator strain and displacement. To allow for comparable results across different studies, the influence of this effect needs to be quantified and taken into account. This paper presents an in-depth study of the active-to-passive ratio by proposing two simplified analytical models for circular DEA and comparing them. The first model is taking the hyperelastic material properties of the dielectric film into account while the second model is a linear elastic lumped parameter model based on the electro-mechanical analogy. Both models lie in good agreement and show a significant linear impact of the radial active-to-passive ratio on the electro-active strain and a resulting maximum of displacement around 50% radial coverage ratio. These findings are validated by experiments with actuators fabricated using silicone membranes. It is shown that the electrode size is not only an important parameter in the experimental design, but in some cases of higher significance for the accuracy of analytical models than the hyperelastic properties of the material. Furthermore, it could be shown that a radial coverage ratio of around 50% is desirable when measuring displacement as it maximizes the displacement and lowers the impact of deviations in electrode sizes due to fabrication errors.

Network Formation, Properties, and Actuation Performance of Functionalized Liquid Isoprene Rubber.

Due to some useful mechanical, dynamic, and dielectric properties along with the ease of processing and forming, liquid rubbers are ideal materials for fabricating dielectric elastomer actuators in various configurations and for many potential applications ranging from automation to automobile and medical industry. In this study, we present a cross-linkable liquid rubber composition where amine-catalyzed esterification reactions lead to the formation of a network structure based on anhydride functional isoprene rubber, carboxyl-terminated nitrile-butadiene rubber, and epoxy end-capped prepolymers. The success of this intricate network formation procedure was verified by HR-MAS NMR spectroscopy. The new isoprene-based elastomeric material exhibits actuation-relevant attributes including a low elastic modulus of 0.45 MPa, soft response to an applied load up to a large deformation of 300%, and a dielectric constant value (2.6) higher than the conventional Elastosil silicone (2.2). A dot actuator comprising of an isoprene dielectric elastomer film in unstretched state and carbon paste electrodes was fabricated that demonstrated an electrode deformation of 0.63%, which is nearly twice as high as for the commercial Elastosil 2030 film (∼0.30%) at 5 kV. Compared to the Elastosil silicone film, the enhanced performance is attributed to the low modulus and high dielectric constant value of the new isoprene elastomer.

Metabolic adaptation of Mycobacterium avium subsp. paratuberculosis to the gut environment.

Knowledge on the proteome level about the adaptation of pathogenic mycobacteria to the environment in their natural hosts is limited. Mycobacterium avium subsp. paratuberculosis (MAP) causes Johne's disease, a chronic and incurable granulomatous enteritis of ruminants, and has been suggested to be a putative aetiological agent of Crohn's disease in humans. Using a comprehensive LC-MS-MS and 2D difference gel electrophoresis (DIGE) approach, we compared the protein profiles of clinical strains of MAP prepared from the gastrointestinal tract of diseased cows with the protein profiles of the same strains after they were grown in vitro. LC-MS-MS analyses revealed that the principal enzymes for the central carbon metabolic pathways, including glycolysis, gluconeogenesis, the tricaboxylic acid cycle and the pentose phosphate pathway, were present under both conditions. Moreover, a broad spectrum of enzymes for ß-oxidation of lipids, nine of which have been shown to be necessary for mycobacterial growth on cholesterol, were detected in vivo and in vitro. Using 2D-DIGE we found increased levels of several key enzymes that indicated adaptation of MAP to the host. Among these, FadE5, FadE25 and AdhB indicated that cholesterol is used as a carbon source in the bovine intestinal mucosa; the respiratory enzymes AtpA, NuoG and SdhA suggested increased respiration during infection. Furthermore higher levels of the pentose phosphate pathway enzymes Gnd2, Zwf and Tal as well as of KatG, SodA and GroEL indicated a vigorous stress response of MAP in vivo. In conclusion, our results provide novel insights into the metabolic adaptation of a pathogenic mycobacterium in its natural host.

Understanding the Impact of Active-to-Passive Area Ratio on Deformation in One-Dimensional Dielectric Elastomer Actuators with Uniaxial Strain State.

There is increasing interest in the use of novel elastomers with inherent or modified advanced dielectric and mechanical properties, as components of dielectric elastomer actuators (DEA). This requires corresponding techniques to assess their electro-mechanical performance. A common way to test dielectric materials is the fabrication of actuators with pre-stretch fixed by a stiff frame. This results in the problem that the electrode size has an influence on the achievable actuator displacement and strain, which is detrimental to the comparability of experiments. This paper presents an in-depth study of the active-to-passive ratio with the aim of investigating the influence of the coverage ratio on uniaxial actuator displacement and strain. To model the effect, a simple lumped-parameter model is proposed. The model shows that the coverage ratio for maximal displacement is 50%. To validate the model results, experiments are carried out. For this, a rectangular, fiber-reinforced DEA is used to assess the relation of the coverage ratio and deformation. Due to the stiffness of the fibers, highly anisotropic mechanical properties are achieved, leading to the uniaxial strain behavior of the actuator, which allows the validation of the one-dimensional model. To consider the influence of the simplifications in the lumped-parameter model, the results are compared to a hyperelastic model. In summary, it is shown that the ratio of the active-to-passive area has a significant influence on the actuator deformation. Both the model and experiments confirm that an active-to-passive ratio of 50% is particularly advantageous in most cases.

THz Thin Film Varactor Based on Integrated Ferroelectric HfZrO2.

In this paper, we present a broadband microwave characterization of ferroelectric hafnium zirconium oxide (Hf0.5Zr0.5O2) metal-ferroelectric-metal (MFM) thin film varactor from 1 kHz up to 0.11 THz. The varactor is integrated into the back-end-of-line (BEoL) of 180 nm CMOS technology as a shunting capacitor for the coplanar waveguide (CPW) transmission line. At low frequencies, the varactor shows a slight imprint behavior, with a maximum tunability of 15% after the wake-up. In the radio- and mmWave frequency range, the varactor's maximum tunability decreases slightly from 13% at 30 MHz to 10% at 110 GHz. Ferroelectric varactors were known for their frequency-independent, linear tunability as well as low loss. However, this potential was never fully realized due to limitations in integration. Here, we show that ferroelectric HfO2 thin films with good back-end-of-line compatibility support very large scale integration. This opens up a broad range of possible applications in the mmWave and THz frequency range such as 6G communications, imaging radar, or THz imaging.

Multitarget Reactive Magnetron Sputtering towards the Production of Strontium Molybdate Thin Films.

X-ray photoelectron spectroscopy was used to study the direct synthesis of strontium and molybdenum oxide thin films deposited by multitarget reactive magnetron sputtering (MT-RMS). Sr and Mo targets with a purity of 99.9% and 99.5%, respectively, were co-sputtered in an argon-oxygen gas mixture. The chamber was provided with an oxygen background flow plus an additional controlled oxygen supply to each of the targets. We demonstrate that variation in the power applied to the Mo target during MT-RMS enables the production of strontium and molybdenum oxide films with variable concentrations of Mo atoms. Both molybdenum and strontium were found in the oxidized state, and no metallic peaks were detected. The deconvoluted high-resolution XPS spectra of molybdenum revealed the presence of several Mo 3d peaks, which indicates molybdenum bonds in a lower valence state. Contrary to the Mo spectra, the high-resolution strontium Sr 3d spectra for the same samples were very similar, and no additional peaks were detected.

Thermoelectric transport properties of Si, SiGe, and silicide CMOS-compatible thin films.

Characterization of thermoelectric transport properties for temperature sensing, cooling, and energy harvesting applications is necessary for a reliable device performance in progressively minimized computer chips. In this contribution, we present a fully automated thermovoltage and sheet resistance measurement setup, which is calibrated and tested for the production of silicon- and silicon-germanium-doped as well as silicide complementary metal-oxide-semiconductor-compatible thin films. A LabVIEW-programmed software application automatically controls the measurement and recording of thermovoltages at individually defined temperature set points. The setup maps average temperature and temperature differences simultaneously in the regime from 40 to 70 °C. The Seebeck coefficient calculated by means of the inversion method was used to eliminate the offset voltage influence. Finally, we present and discuss the Seebeck coefficient as well as the sheet resistance for application-specific different temperature set points of several doped poly-Si, poly-SiGe, and silicides.

Identification of immunogenic proteins and generation of antibodies against Salmonella Typhimurium using phage display.

BACKGROUND: Solely in Europoe, Salmonella Typhimurium causes more than 100,000 infections per year. Improved detection of livestock colonised with S. Typhimurium is necessary to prevent foodborne diseases. Currently, commercially available ELISA assays are based on a mixture of O-antigens (LPS) or total cell lysate of Salmonella and are hampered by cross-reaction. The identification of novel immunogenic proteins would be useful to develop ELISA based diagnostic assays with a higher specificity. RESULTS: A phage display library of the entire Salmonella Typhimurium genome was constructed and 47 immunogenic oligopeptides were identified using a pool of convalescent sera from pigs infected with Salmonella Typhimurium. The corresponding complete genes of seven of the identified oligopeptids were cloned. Five of them were produced in E. coli. The immunogenic character of these antigens was validated with sera from pigs infeced with S. Tyhimurium and control sera from non-infected animals. Finally, human antibody fragments (scFv) against these five antigens were selected using antibody phage display and characterised. CONCLUSION: In this work, we identified novel immunogenic proteins of Salmonella Typhimurium and generated antibody fragments against these antigens completely based on phage display. Five immunogenic proteins were validated using a panel of positive and negative sera for prospective applications in diagnostics of Salmonela Typhimurium.

Experimental Actinobacillus pleuropneumoniae challenge in swine: comparison of computed tomographic and radiographic findings during disease.

BACKGROUND: In pigs, diseases of the respiratory tract like pleuropneumonia due to Actinobacillus pleuropneumoniae (App) infection have led to high economic losses for decades. Further research on disease pathogenesis, pathogen-host-interactions and new prophylactic and therapeutic approaches are needed. In most studies, a large number of experimental animals are required to assess lung alterations at different stages of the disease. In order to reduce the required number of animals but nevertheless gather information on the nature and extent of lung alterations in living pigs, a computed tomographic scoring system for quantifying gross pathological findings was developed. In this study, five healthy pigs served as control animals while 24 pigs were infected with App, the causative agent of pleuropneumonia in pigs, in an established model for respiratory tract disease. RESULTS: Computed tomographic (CT) findings during the course of App challenge were verified by radiological imaging, clinical, serological, gross pathology and histological examinations. Findings from clinical examinations and both CT and radiological imaging, were recorded on day 7 and day 21 after challenge. Clinical signs after experimental App challenge were indicative of acute to chronic disease. Lung CT findings of infected pigs comprised ground-glass opacities and consolidation. On day 7 and 21 the clinical scores significantly correlated with the scores of both imaging techniques. At day 21, significant correlations were found between clinical scores, CT scores and lung lesion scores. In 19 out of 22 challenged pigs the determined disease grades (not affected, slightly affected, moderately affected, severely affected) from CT and gross pathological examination were in accordance. Disease classification by radiography and gross pathology agreed in 11 out of 24 pigs. CONCLUSIONS: High-resolution, high-contrast CT examination with no overlapping of organs is superior to radiography in the assessment of pneumonic lung lesions after App challenge. The new CT scoring system allows for quantification of gross pathological lung alterations in living pigs. However, computed tomographic findings are not informative of the etiology of respiratory disease.

Suitability of Different Analytical Derivations of Electrically Induced Stress States in Planar and Cylindrical Dielectric Elastomer Actuators.

Dielectric elastomers (DE) belong to a very performant and efficient class of functional materials for actuators, while being compliant, low-weight and silent, they offer high energy efficiencies and large deformations under an applied electric field. In this work, a comparison of different approaches to derive expressions for the electrically induced stress states in dielectric materials is given. In particular, the focus is on three different ways to analytically describe stress states in planar actuator setups and to show how they are connected to each other regarding their resulting deformations. This is the basis to evaluate the suitability of these approaches for cylindrical actuator geometries together with exemplary calculations for concrete use cases. As an outcome, conclusions on the suitability of the different approaches for certain actuator setups are drawn. In particular cylindrical actuator geometries are taken into account and a recommendation on which approach is useful to describe a certain actuator effect is given.