Inflow cannula position as risk factor for stroke in patients with HeartMate 3 left ventricular assist devices.

BACKGROUND: A relation between the left ventricular assist device inflow cannula (IC) malposition and pump thrombus has been reported. This study aimed to investigate if the pump position, derived from chest X-rays in HeartMate 3 (HM3) patients, correlates with neurological dysfunction (ND), ischemic stroke (IS), hemorrhagic stroke (HS) and survival. METHODS: This analysis was performed on routinely acquired X-rays of 42 patients implanted with a HM3 between 2014 and 2017. Device position was quantified in patients with and without ND from frontal and lateral X-rays characterizing the IC and pump in relation to spine, diaphragm or horizontal line. The primary end-point was freedom from stroke and survival one-year after HM3 implantation stratified by pump position. RESULTS: The analysis of X-rays, 33.5 (41.0) days postoperative, revealed a significant smaller IC angle of HM3 patients with ND versus no ND (0.1° ± 14.0° vs. 12.9° ± 10.1°, p = 0.005). Additionally, the IC angle in the frontal view, IS: 4.1 (20.9)° versus no IS: 13.8 (7.5)°, p = 0.004 was significantly smaller for HM3 patients with IS. Using receiver operating characteristics derived cut-off, IC angle <10° provided 75% sensitivity and 100% specificity (C-statistic = 0.85) for predicting IS. Stratified by IC angle, freedom from IS at 12 months was 100% (>10°) and 60% (<10°) respectively (p = 0.002). No significant differences were found in any end-point between patients with and without HS. One-year survival was significantly higher in patients with IC angle >10° versus <10° (100% vs. 71.8%, p = 0.012). CONCLUSIONS: IC malposition derived from standard chest X-rays serves as a risk factor for ND, IS and worse survival in HM3 patients.

Impact of Infant Positioning on Cardiopulmonary Resuscitation Performance During Simulated Pediatric Cardiac Arrest: A Randomized Crossover Study.

OBJECTIVES: The primary objective was to determine the impact of infant positioning on cardiopulmonary resuscitation performance during simulated pediatric cardiac arrest. DESIGN: A single-center, prospective, randomized, unblinded manikin study. SETTING: Medical university-affiliated simulation facility. SUBJECTS: Fifty-two first-line professional rescuers (n = 52). INTERVENTIONS: Performance of cardiopulmonary resuscitation was determined using an infant manikin model in three different positions (on a table [T], on the provider's forearm with the manikin's head close to the provider's elbow [P], and on the provider's forearm with the manikin's head close to the provider's palm [D]). For the measurement of important cardiopulmonary resuscitation performance variables, a commercially available infant simulator was modified. In a randomized sequence, healthcare professionals performed single-rescuer cardiopulmonary resuscitation for 3 minutes in each position. Performances of chest compression (primary outcome), ventilation, and hands-off time were analyzed using a multilevel regression model. MEASUREMENTS AND MAIN RESULTS: Mean (± SD) compression depth significantly differed between table and the other two manikin positions (31 ± 2 [T], 29 ± 3 [P], and 29 ± 3 mm [D]; overall p < 0.001; repeated measures design adjusted difference: T vs P, -2 mm [95% CI, -2 to -1 mm]; T vs D, -1 mm [95% CI, -2 to -1 mm]). Secondary outcome variables showed no significant differences. CONCLUSIONS: Compressions were significantly deeper in the table group compared to positions on the forearm during cardiopulmonary resuscitation, yet the differences were small and perhaps not clinically important.

Fluid Dynamics in the HeartMate 3: Influence of the Artificial Pulse Feature and Residual Cardiac Pulsation.

Ventricular assist devices (VADs), among which the HeartMate 3 (HM3) is the latest clinically approved representative, are often the therapy of choice for patients with end-stage heart failure. Despite advances in the prevention of pump thrombosis, rates of stroke and bleeding remain high. These complications are attributed to the flow field within the VAD, among other factors. One of the HM3's characteristic features is an artificial pulse that changes the rotor speed periodically by 4000 rpm, which is meant to reduce zones of recirculation and stasis. In this study, we investigated the effect of this speed modulation on the flow fields and stresses using high-resolution computational fluid dynamics. To this end, we compared Eulerian and Lagrangian features of the flow fields during constant pump operation, during operation with the artificial pulse feature, and with the effect of the residual native cardiac cycle. We observed good washout in all investigated situations, which may explain the low incidence rates of pump thrombosis. The artificial pulse had no additional benefit on scalar washout performance, but it induced rapid variations in the flow velocity and its gradients. This may be relevant for the removal of deposits in the pump. Overall, we found that viscous stresses in the HM3 were lower than in other current VADs. However, the artificial pulse substantially increased turbulence, and thereby also total stresses, which may contribute to clinically observed issues related to hemocompatibility.

Investigation of the Axial Gap Clearance in a Hydrodynamic-Passive Magnetically Levitated Rotary Blood Pump Using X-Ray Radiography.

The HeartWare HVAD is a radial rotary blood pump with a combination of passive magnetic and hydrodynamic bearings to levitate the impeller. The axial gap size between impeller and housing in this bearing and its sensitivity to speed, flow, and pressure difference is difficult to assess. Shear stresses are exceptionally high in this tiny gap making it important for blood damage and related adverse events. Therefore, the aim of this study was to measure the axial gap clearance in the HVAD at different operating conditions employing radiography. To quantify the gap size in the HVAD, the pump was positioned 30 mm in front of the X-ray source employing a microfocus X-ray tube with an acceleration voltage up to 300 kV. Beams were detected on a flat panel detector (Perkin Elmer XRD 1611-CP3). The pump was connected to a tubing circuit with a throttle to adjust flow (0, 5, 10 L/min) and a water glycerol mixture to set the desired viscosity (1, 4, 8 mPas). Rotational speed was varied between 1800 and 3600 rpm. In this study, for clinically relevant conditions at 5 L/min and 2700 rpm, the axial gap was 22 µm. The gap size increased with rotational speeds dependent on the viscosity (2.8, 6.9, and 9.4 µm/1000 rpm for 1, 4, and 8 mPas, respectively), but was independent from the volume flow and the pressure head at constant speeds. In summary, using X-ray radiographic imaging small gaps in a rotary blood pump during operation can be measured in a nondestructive contact-free way. The axial hydrodynamic bearing gap in the HVAD pump was determined to be in the range of about three times the diameter of a red blood cell. Its dependence on operating volume flow and generated pressure head across the pump is not pronounced.

Interaction of a Transapical Miniaturized Ventricular Assist Device With the Left Ventricle: Hemodynamic Evaluation and Visualization in an Isolated Heart Setup.

New left ventricular assist devices (LVADs) offer both important advantages and potential hazards. VAD development requires better and expeditious ways to identify these advantages and hazards. We validated in an isolated working heart the hemodynamic performance of an intraventricular LVAD and investigated how its outflow cannula interacted with the aortic valve. Hearts from six pigs were explanted and connected to an isolated working heart setup. A miniaturized LVAD was implanted within the left ventricle (tMVAD, HeartWare Inc., Miami Lakes, FL, USA). In four experiments blood was used to investigate hemodynamics under various loading conditions. In two experiments crystalloid perfusate was used, allowing visualization of the outflow cannula within the aortic valve. In all hearts the transapical miniaturized ventricular assist device (tMVAD) implantation was successful. In the blood experiments hemodynamics similar to those observed clinically were achieved. Pump speeds ranged from 9 to 22 krpm with a maximum of 7.6 L/min against a pressure difference between ventricle and aorta of ∼50 mm Hg. With crystalloid perfusate, central positioning of the outflow cannula in the aortic root was observed during full and partial support. With decreasing aortic pressures the cannula tended to drift toward the aortic root wall. The tMVAD could unload the ventricle similarly to LVADs under conventional cannulation. Aortic pressure influenced central positioning of the outflow cannula in the aortic root. The isolated heart is a simple, accessible evaluation platform unaffected by complex reactions within a whole, living animal. This platform allowed detection and visualization of potential hazards.

Pump Speed Waveform Analysis to Detect Aortic Valve Opening in Patients on Ventricular Assist Device Support.

As the aortic valve (AV) opens, the pump pressure head remains constant, which is reflected as a "notch/plateau" in pump pressure and flow signals. However, instantaneous flow estimation may be influenced by friction and is particularly difficult in axial pumps. Therefore, a new method to determine the duration of AV opening based on the area under the curve (AUC) of the power spectral density analysis of pump speed signal was developed. Data from patients implanted with HeartWare HVAD left ventricular assist device were studied at different pump speeds, with simultaneous transthoracic echocardiography in two cohorts. In the first group, pump data of 15 patients were used to investigate the ability to discriminate between an open and closed AV. In the second cohort of a further 13 patients, the duration of AV opening was measured from digitized M-mode images, and the relationship between the AV opening time and the new method assessed. In 14 of the initial 15 patients, AV status could be discriminated using only one threshold for all patients. In the second cohort, gradual speed reduction resulted in aortic valve opening in 12 of the 13 patients. The correlation between AV opening duration and AUC was 0.96 ± 0.03. Regression analysis indicated a linear relationship in each of the patients with a small error between the fit and the measured opening time (root mean square error = 11.0 ± 7.6 ms). However, the slopes (69.0 ± 52.8) and intercepts (-31.4 ± 78.0) varied widely between patients. The sensitivity and specificity for the new method using AUC threshold of 0.95 for aortic valve closure was 95% and 91%, respectively. The newly developed method to detect AV opening not only provides information on the AV status during LVAD support (open/closed) but also gives insight into the duration of AV opening. Because the slope of the relationship varies from patient to patient, initial training and adaptation of the method to each patient seems to be required.

Assessment of aortic valve opening during rotary blood pump support using pump signals.

During left ventricular support by rotary blood pumps (RBPs), the biomechanics of the aortic valve (AV) are altered, potentially leading to adverse events like commissural fusion, valve insufficiency, or thrombus formation. To avoid these events, assessment of AV opening and consequent adaptation of pump speed seem important. Additionally, this information provides insight into the heart-pump interaction. The aim of this study was to develop a method to assess AV opening from the pump flow signal. Data from a numerical model of the cardiovascular system and animal experiments with an RBP were employed to detect the AV opening from the flow waveform under different hemodynamic conditions. Three features calculated from the pump flow waveform were used to classify the state of the AV: skewness, kurtosis, and crest factor. Three different classification algorithms were applied to determine the state of the AV based on these features. In the model data, the best classifier resulted in a percentage of correctly identified beats with a closed AV (specificity) of 99.9%. The percentage of correctly identified beats with an open AV (sensitivity) was 99.5%. In the animal experiments, specificity was 86.8% and sensitivity reached 96.5%. In conclusion, a method to detect AV opening independently from preload, afterload, heart rate, contractility, and degree of support was developed. This algorithm makes the evaluation of the state of the AV possible from pump data only, allowing pump speed adjustment for a frequent opening of the AV and providing information about the interaction of the native heart with the RBP.

Continuous monitoring of cardiac rhythms in left ventricular assist device patients.

Monitoring of cardiac rhythms is of major importance in the treatment of heart failure patients with left ventricular assist devices (LVADs) implanted. A continuous surveillance of these rhythms could improve out-of-hospital care in these patients. The aim of this study was to investigate cardiac rhythms using available pump data only. Datasets (n = 141) obtained in the normal ward, in the intensive care unit, and during bicycle ergometry were analyzed in 11 recipients of a continuous flow LVAD (59.1 ± 9.7 years; male 82%). Tachograms and arrhythmic patterns derived from the pump flow waveform, and a simultaneously recorded ECG were compared, as well as heart rate variability parameters such as: the average heart beat duration (RR interval), the standard deviation of the beat duration (SDNN), the root-mean-square of the difference of successive beat durations (RMSSD), and the number of pairs of adjacent beat duration differing by >50 ms divided by the number of all beats (pNN50). A very good agreement of cardiac rhythm parameters from the pump flow compared with ECG was found. Tachycardia, atrial fibrillation, and extrasystoles could be accurately identified from the tachograms derived from the pump flow. Also, Bland-Altman analysis comparing pump flow with ECG indicated a very small difference in average RR interval of 0.3 ± 1.0 ms, in SSDN of 0.5 ± 2.7 ms, in RMSSD of 1.0 ± 5.6 ms, and in pNN50 of 0.3 ± 1.0%. Continuous monitoring of cardiac rhythms from available pump data is possible. It has the potential to reduce the out-of-hospital diagnostic burden and to permit a more efficient adjustment of the level of mechanical support.

Left Atrial Decompression With the HeartMate3 in Heart Failure With Preserved Ejection Fraction: Virtual Fitting and Hemodynamic Analysis.

Effective treatment of heart failure with preserved ejection fraction (HFpEF) remains an unmet medical need. Although left atrial decompression using mechanical circulatory support devices was previously suggested, the heterogeneous HFpEF population and the lack of tailored devices have prevented the translation into clinical practice. This study aimed to evaluate the feasibility of left atrial decompression in HFpEF patients with a HeartMate 3 (HM3, Abbott Inc, Chicago, USA) in silico and in vitro . Anatomic compatibility of the HM3 pump was assessed by virtual device implantation into the left atrium through the left atrial appendage (LAA) and left atrial posterior wall (LAPW) of 10 HFpEF patients. Further, the efficacy of left atrial decompression was investigated experimentally in a hybrid mock loop, replicating the hemodynamics of an HFpEF phenotype at rest and exercise conditions. Virtual implantation without substantial intersection with surrounding tissues was accomplished through the LAA in 90% and 100% through the LAPW. Hemodynamic analysis in resting conditions demonstrated normalization of left atrial pressures without backflow at a pump speed of around 5400 rpm, whereas a range of 6400-7400 rpm was required during exercise. Therefore, left atrial decompression with the HM3 may be feasible in terms of anatomic compatibility and hemodynamic efficacy.

A Novel Pumping Principle for a Total Artificial Heart.

OBJECTIVE: Total artificial hearts (TAH) serve as a temporary treatment for severe biventricular heart failure. The limited durability and complication rates of current devices hamper long-term cardiac replacement. The aim of this study was to assess the feasibility of a novel valveless pumping principle for a durable pulsatile TAH (ShuttlePump). METHODS: The pump features a rotating and linearly shuttling piston within a cylindrical housing with two in- and outlets. With a single moving piston, the ShuttlePump delivers pulsatile flow to both systemic and pulmonary circulation. The pump and actuation system were designed iteratively based on analytical and in silico methods, utilizing finite element methods (FEM) and computational fluid dynamics (CFD). Pump characteristics were evaluated experimentally in a mock circulation loop mimicking the cardiovascular system, while hemocompatibility-related parameters were calculated numerically. RESULTS: Pump characteristics cover the entire required operating range for a TAH, providing 2.5-9 L/min of flow rate against 50-160 mmHg arterial pressures at stroke frequencies of 1.5-5 Hz while balancing left and right atrial pressures. FEM analysis showed mean overall copper losses of 8.84 W, resulting in a local maximum blood temperature rise of <2 K. The CFD results of the normalized index of hemolysis were 3.57 mg/100 L, and 95% of the pump's blood volume was exchanged after 1.42 s. CONCLUSION AND SIGNIFICANCE: This study indicates the feasibility of a novel pumping system for a TAH with numerical and experimental results substantiating further development of the ShuttlePump.

Multiobjective Optimization of Rotodynamic Blood Pumps: The Use Case of a Cavopulmonary Assist Device.

Comprehensive optimization of rotodynamic blood pumps (RBPs) requires the consideration of three partially conflicting objectives: size, hemocompatibility, and motor efficiency. Optimizing these individual objectives independently, the potential of multiobjective optimizations often remains untapped. This study aimed at the multiobjective optimization of an RBP for cavopulmonary support accounting for all three objectives simultaneously. Hydraulic and electromagnetic design spaces were characterized using computational fluid dynamics and computational electromagnetics, respectively. Design variables included secondary flow gap widths, impeller diameters, and stator heights. The size objective encompassed the RBP widths and heights, the hemocompatibility objective was a weighted composite measure of well-established metrics, and the motor objective was determined by motor losses. Multiobjective optimization was performed through Pareto analysis. 81 designs were considered, and 21 Pareto-optimal designs were identified. The Pareto analysis indicated that hemocompatibility performance could be improved by 72.4% with a concomitant 1.5% reduction in the baseline pump volume. This, however, entailed an increase in motor losses by 0.2 W, while still meeting design requirements, with maximum local temperature rises remaining below 0.4 K. The multiobjective optimization led to a Pareto front, demonstrating the feasibility to improve hemocompatibility at reduced pump volume, however, at the cost of a diminished yet still acceptable motor performance.

An Atraumatic Mock Loop for Realistic Hemocompatibility Assessment of Blood Pumps.

OBJECTIVE: Conventional mock circulatory loops (MCLs) cannot replicate realistic hemodynamic conditions without inducing blood trauma. This constrains in-vitro hemocompatibility examinations of blood pumps to static test loops that do not mimic clinical scenarios. This study aimed at developing an atraumatic MCL based on a hardware-in-the-loop concept (H-MCL) for realistic hemocompatibility assessment. METHODS: The H-MCL was designed for 450 ± 50 ml of blood with the polycarbonate reservoirs, the silicone/polyvinyl-chloride tubing, and the blood pump under investigation as the sole blood-contacting components. To account for inherent coupling effects a decoupling pressure control was derived by feedback linearization, whereas the level control was addressed by an optimization task to overcome periodic loss of controllability. The HeartMate 3 was showcased to evaluate the H-MCL's accuracy at typical hemodynamic conditions. To verify the atraumatic properties of the H-MCL, hemolysis (bovine blood, n = 6) was evaluated using the H-MCL in both inactive (static) and active (minor pulsatility) mode, and compared to results achieved in conventional loops. RESULTS: Typical hemodynamic scenarios were replicated with marginal coupling effects and root mean square error (RMSE) below 1.74 ± 1.37 mmHg while the fluid level remained within ±4% of its target value. The normalized indices of hemolysis (NIH) for the inactive H-MCL showed no significant differences to conventional loops ( ∆NIH = -1.6 mg/100 L). Further, no significant difference was evident between the active and inactive mode in the H-MCL ( ∆NIH = +0.3 mg/100 L). CONCLUSION AND SIGNIFICANCE: Collectively, these findings indicated the H-MCL's potential for in-vitro hemocompatibility assessment of blood pumps within realistic hemodynamic conditions, eliminating inherent setup-related risks for blood trauma.

In-Vitro Flow Validation of Third-Generation Ventricular Assist Devices: Feasibility and Challenges.

Computational fluid dynamics (CFD) is a powerful tool for the in-silico evaluation of rotodynamic blood pumps (RBPs). Corresponding validation, however, is typically restricted to easily accessible, global flow quantities. This study showcased the HeartMate 3 (HM3) to identify feasibility and challenges of enhanced in-vitro validation in third-generation RBPs. To enable high-precision acquisition of impeller torques and grant access for optical flow measurements, the HM3 testbench geometry was geometrically modified. These modifications were reproduced in silico , and global flow computations validated along 15 operating conditions. The globally validated flow in the testbench geometry was compared with CFD-simulated flows in the original geometry to assess the impact of the necessary modifications on global and local hydraulic properties. Global hydraulic properties in the testbench geometry were successfully validated (pressure head: r = 0.999, root mean square error [RMSE] = 2.92 mmHg; torque: r = 0.996, RMSE = 0.134 mNm). In-silico comparison with the original geometry demonstrated good agreement ( r > 0.999, relative errors < 11.97%) of global hydraulic properties. Local hydraulic properties (errors up to 81.78%) and hemocopatibility predictions (deviations up to 21.03%), however, were substantially affected by the geometric modifications. Transferability of local flow measures derived on advanced in-vitro testbenches toward original pump designs is challenged by significant local effects associated with the necessary geometrical modifications.

Anatomical Compliance of Cavopulmonary Assist Device Designs: A Virtual Fitting Study in Fontan Patients.

Several device designs for cavopulmonary mechanical circulatory support (MCS) are under investigation, however, challenged by the Fontan population's heterogeneity in size, cardiovascular and thoracic anatomy. This study aimed to preclinically assess the anatomical compliance of proposed device designs in silico. Representative double- and single-outlet cavopulmonary assist device (CPAD) designs were virtually implanted into CT imaging data of 10 patients previously palliated with total cavopulmonary connection (TCPC) for functionally univentricular hearts. Anatomical device compatibility was characterized concerning pump proximity to cardiovascular, respiratory and thoracic structures, as well as pump in- and outflow graft configuration. In 10 Fontan patients with a median age of 10.4 years (interquartile range [IQR] 5.0-15.3 years) and a median body surface area of 1.09 m2 (IQR 0.76-1.28 m2), implantation of a double-outlet CPAD was feasible in 1 patient (10%). In all other, adverse device intersection with the trachea and (neo-)aorta, or posterior pulmonary artery outflow graft kinking were observed. A single-outlet design permitted enhanced device mobilization adapting to individual anatomical conditions, resulting in device fit in nine of 10 patients (90%). Despite vast anatomical variations among single ventricle patients, a single-outlet device design may provide intracorporeal cavopulmonary MCS to a broad spectrum of failing Fontan patients.

Feasibility of an Animal Model for Cavopulmonary Support With a Double-Outflow Pump.

Both single- and double-outflow cavopulmonary assist devices (CPADs) were recently proposed for the Fontan population, whereas single-outflow configurations were evaluated in large animal trials and double-outflow concepts are lacking an equivalent in vivo assessment. The aim of this study was to test the hemodynamic properties of a double-outflow CPAD device in an acute sheep model. The two inflow cannulae of a CPAD were anastomosed to the caval veins. Outflow graft connection was performed via end-to-side anastomosis to the right (RPA) and main pulmonary artery (MPA). Speed ramp protocols were conducted, and hemodynamic effects were monitored in terms of caval flows, cardiac output (CO), central venous pressure (CVP), pulmonary artery pressure (PAP), and left atrial pressure (LAP). Six experiments were conducted (53.35 ± 5.1 kg). In three experiments, the animal model was established, the CPAD was examined, and restoration of biventricular equivalency in terms of venous return was achieved. Venous pressures (CVP) declined linearly with increasing pump speed (r > 0.879), whereas caval flow (r > 0.973), CO (r > 0.993), PAP (r > 0.973), and LAP (r > 0.408) increased. Despite the considerable complexity of the sheep model caused by the sheep pulmonary arterial anatomy that requires substantial graft bending, the CPAD was evaluated in three acute experiments and showed the potential to completely substitute a subpulmonary ventricle.

Evaluation of left ventricular relaxation in rotary blood pump recipients using the pump flow waveform: a simulation study.

In heart failure, diastolic dysfunction is responsible for about 50% of the cases, with higher prevalence in women and elderly persons and contributing similarly to mortality as systolic dysfunction. Whereas the cardiac systolic diagnostics in ventricular assist device patients from pump parameters have been investigated by several groups, the diastolic behavior has been barely discussed. This study focuses on the determination of ventricular relaxation during early diastole in rotary blood pump (RBP) recipients. In conventional cardiology, relaxation is usually evaluated by the minimum rate and the time constant of left ventricular pressure decrease, dP/dt(min) and τ(P) . Two new analogous indices derived from the pump flow waveform were investigated in this study: the minimum rate and the time constant of pump flow decrease, dQ/dt(min) and τ(Q) . The correspondence between the indices was investigated in a numerical simulation of the assisted circulation for different ventricular relaxation states (τ(P) ranging from 24 to 68 ms) and two RBP models characterized by linear and nonlinear pressure-flow characteristics. dQ/dt(min) and τ(Q) always correlated with the dP/dt(min) and τ(P) , respectively (r>0.97). These relationships were influenced by the nonlinear pump characteristics during partial support and by the pump speed during full support. To minimize these influences, simulation results suggest the evaluation of dQ/dt(min) and τ(Q) at a pump speed that corresponds to the borderline between partial and full support. In conclusion, at least in simulation, relaxation can be derived from pump data. This noninvasively accessible information could contribute to a continuous estimation of the remaining cardiac function and its eventual recovery.

Development of a pump flow estimator for rotary blood pumps to enhance monitoring of ventricular function.

Estimation of instantaneous flow in rotary blood pumps (RBPs) is important for monitoring the interaction between heart and pump and eventually the ventricular function. Our group has reported an algorithm to derive ventricular contractility based on the maximum time derivative (dQ/dt(max) as a substitute for ventricular dP/dt(max) ) and pulsatility of measured flow signals. However, in RBPs used clinically, flow is estimated with a bandwidth too low to determine dQ/dt(max) in the case of improving heart function. The aim of this study was to develop a flow estimator for a centrifugal pump with bandwidth sufficient to provide noninvasive cardiac diagnostics. The new estimator is based on both static and dynamic properties of the brushless DC motor. An in vitro setup was employed to identify the performance of pump and motor up to 20 Hz. The algorithm was validated using physiological ventricular and arterial pressure waveforms in a mock loop which simulated different contractilities (dP/dt(max) 600 to 2300 mm Hg/s), pump speeds (2 to 4 krpm), and fluid viscosities (2 to 4 mPa·s). The mathematically estimated pump flow data were then compared to the datasets measured in the mock loop for different variable combinations (flow ranging from 2.5 to 7 L/min, pulsatility from 3.5 to 6 L/min, dQ/dt(max) from 15 to 60 L/min/s). Transfer function analysis showed that the developed algorithm could estimate the flow waveform with a bandwidth up to 15 Hz (±2 dB). The mean difference between the estimated and measured average flows was +0.06 ± 0.31 L/min and for the flow pulsatilities -0.27 ± 0.2 L/min. Detection of dQ/dt(max) was possible up to a dP/dt(max) level of 2300 mm Hg/s. In conclusion, a flow estimator with sufficient frequency bandwidth and accuracy to allow determination of changes in ventricular contractility even in the case of improving heart function was developed.

Comparison of device-based therapy options for heart failure with preserved ejection fraction: a simulation study.

Successful therapy of heart failure with preserved ejection fraction (HFpEF) remains a major unmet clinical need. Device-based treatment approaches include the interatrial shunt device (IASD), conventional assist devices pumping blood from the left ventricle (LV-VAD) or the left atrium (LA-VAD) towards the aorta, and a valveless pulsatile assist device with a single cannula operating in co-pulsation with the native heart (CoPulse). Hemodynamics of two HFpEF subgroups during rest and exercise condition were translated into a lumped parameter model of the cardiovascular system. The numerical model was applied to assess the hemodynamic effect of each of the four device-based therapies. All four therapy options show a reduction in left atrial pressure during rest and exercise and in both subgroups (> 20%). IASDs concomitantly reduce cardiac output (CO) and shift the hemodynamic overload towards the pulmonary circulation. All three mechanical assist devices increase CO while reducing sympathetic activity. LV-VADs reduce end-systolic volume, indicating a high risk for suction events. The heterogeneity of the HFpEF population requires an individualized therapy approach based on the underlying hemodynamics. Whereas phenotypes with preserved CO may benefit most from an IASD device, HFpEF patients with reduced CO may be candidates for mechanical assist devices.

The effect of occlusive polytetrafluoroethylene outflow graft protectors in left ventricular assist device recipients.

BACKGROUND: The use of polytetrafluoroethylene (PTFE) material as a protective cover for left ventricular assist device (LVAD) outflow grafts (OG) is a common practice. However, it has descriptively been linked to the development of blood flow obstruction (BFO). METHODS: Patient data from 194 consecutive HVAD (Medtronic Inc; Medtronic, Minneapolis, MN) recipients implanted between March 2006 and January 2021 were retrospectively analyzed. PTFE covers were used in 102 patients. Study outcomes included the incidence of BFO and survival on LVAD support. RESULTS: Thirty-seven patients (19.1%) developed BFO during the study period. On a multivariable Cox regression analysis, PTFE use was an independent predictor for the development of BFO (HR 2.15, 95% CI 1.03-4.48, p = .04). BFO comprised of 2 types of device malfunction: eleven patients (5.7%) developed outflow graft stenosis (OGS), and 31 patients (16.0%) developed pump thrombosis (PT). There was a significantly higher cumulative incidence of OGS in patients with PTFE cover than in those without (Gray's test, p =.03). However, the observed higher cumulative incidence of PT in PTFE patients was non-significant (Gray's test, p =.06). In a multivariable Cox regression model, the effect of PTFE use on survival was non-significant (HR 0.95, 95% CI 0.60-1.48, p =.81), while the development of BFO was independently associated with increased mortality (HR 3.43, 95% CI 1.94-6.06, p < .0001). CONCLUSIONS: The use of PTFE OG cover in LVAD patients is associated with an increased cumulative probability of development of BFO, the latter adversely impacting survival and is therefore, harmful.

First-in-man use of the EXCOR Venous Cannula for combined cavopulmonary and systemic ventricular support in Fontan circulation failure.

BACKGROUND AND AIM: The Berlin Heart EXCOR system has been developed for mechanical circulatory support (MCS) of pediatric patients with terminal heart failure. A recently introduced iteration of the system (EXCOR Venous Cannula, Berlin Heart GmbH, Berlin, Germany) is dedicated to support patients with univentricular physiologies by facilitating implantation of the EXCOR device into the Fontan pathway. CASE PRESENTATION: We report the worldwide first successful implantation of the EXCOR Venous Cannula in a biventricular support concept for a 12-year-old boy (140 cm, 42.7 kg, body surface area 1.29 m2, Pedimacs Level 2) with severe systemic ventricle dysfunction and failing Fontan circulation. Surgery comprised of standard Berlin Heart EXCOR implantation to support the failing ventricle (12 mm apex / staged 12/9 mm arterial cannula / 50 ml ventricle). Cannulation for subpulmonary EXCOR support was achieved by performing a total cavopulmonary connection takedown with subsequent anastomosis of a staged 12/9 mm outflow cannula to the pulmonary artery and implantation of a 14/18 mm EXCOR Venous Cannula as subpulmonary inflow graft, which was connected to the superior vena cava and Fontan tunnel using GORE-TEX grafts. In the postoperative course, cardiac output and central venous pressures rapidly improved with hepatic and renal functions restoring to age- and condition-specific norm values. CONCLUSION: The Berlin Heart EXCOR Venous Cannula is the first system for standardized mechanical support of Fontan circulatory failure. In our patient, subpulmonary support restoring a biventricular circulation combined with systemic MCS normalized hemodynamics and reversed end-organ dysfunction.