RESUMO
Thermochromic smart windows with rational modulation in indoor temperature and brightness draw considerable interest in reducing building energy consumption, which remains a huge challenge to meet the comfortable responsive temperature and the wide transmittance modulation range from visible to near-infrared (NIR) light for their practical application. Herein, a novel thermochromic Ni(II) organometallic of [(C2 H5 )2 NH2 ]2 NiCl4 for smart windows is rationally designed and synthesized via an inexpensive mechanochemistry method, which processes a low phase-transition temperature of 46.3 °C for the reversible color evolution from transparent to blue with a tunable visible transmittance from 90.5% to 72.1%. Furthermore, cesium tungsten bronze (CWO) and antimony tin oxide (ATO) with excellent NIR absorption in 750-1500 and 1500-2600 nm are introduced in the [(C2 H5 )2 NH2 ]2 NiCl4 -based smart windows, realizing a broadband sunlight modulation of a 27% visible light modulation and more than 90% of NIR shielding ability. Impressively, these smart windows demonstrate stable and reversible thermochromic cycles at room temperature. Compared with the conventional windows in the field tests, these smart windows can significantly reduce the indoor temperature by 16.1 °C, which is promising for next-generation energy-saving buildings.
RESUMO
Flavin mononucleotide (FMN) derived from Vitamin B2, a bio-based fluorescent water-soluble molecule with visible yellow-green fluorescence, has been used in the scope of producing photoluminescent and glow-in-the-dark patterned polyester (PET) nonwoven panels. Since the FMN molecule cannot diffuse inside the PET fiber, screen printing, coating, and padding methods were used in an attempt to immobilize FMN molecules at the PET fiber surface of a nonwoven, using various biopolymers such as gelatin and sodium alginate as well as a water-based commercial polyacrylate. In parallel, air atmospheric plasma activation of PET nonwoven was carried for improved spreading and adhesion of FMN bearing biopolymer/polymer mixture. Effectively, the plasma treatment yielded a more hydrophilic PET nonwoven, reduction in wettability, and surface roughness of the plasma treated fiber with reduced water contact angle and increased capillary uptake were observed. The standard techniques of morphological properties were explored by a scanning electron microscope (SEM) and atomic force microscopy (AFM). Films combining each biopolymer and FMN were formed on PS (polystyrene) Petri-dishes. However, only the gelatin and polyacrylate allowed the yellow-green fluorescence of FMN molecule to be maintained on the film and PET fabric (seen under ultraviolet (UV) light). No yellow-green fluorescence of FMN was observed with sodium alginate. Thus, when the plasma-activated PET was coated with the gelatin mixture or polyacrylate bearing FMN, the intense photoluminescent yellow-green glowing polyester nonwoven panel was obtained in the presence of UV light (370 nm). Screen printing of FMN using a gelatin mixture was possible. The biopolymer exhibited appropriate viscosity and rheological behavior, thus creating a glow-in-the-dark pattern on the polyester nonwoven, with the possibility of one expression in daylight and another in darkness (in presence of UV light). A bio-based natural product such as FMN is potentially an interesting photoluminescent molecule with which textile surface pattern designers may create light-emitting textiles and interesting aesthetic expressions.
Assuntos
Mononucleotídeo de Flavina , Poliésteres , Plasma , Riboflavina , MolhabilidadeRESUMO
Biobased lignin represents one of the possible materials for next-generation flame retardant additives due to its sustainability, environmental benefits and comparable efficiency to other flame retardant (FR) additives. In this context, this study presents the development of FR polyamide 11 (PA11) multifilament yarns and fabric structures containing different industrial lignins (i.e., lignosulfonate lignin (LL), and Kraft lignin (KL)) and zinc phosphinate (ZnP). The combination of ZnP and lignin (KL or LL) at different weight ratios were used to prepare flame retarded PA11 blends by melt mixing using a twin-screw extruder. These blends were transformed into continuous multifilament yarns by the melt-spinning process even at a high concentration of additives as 20 wt%. The mechanical test results showed that the combination of KL and ZnP achieved higher strength and filaments showed regularity in structure as compared to the LL and ZnP filaments. Thermogravimetric (TG) analysis showed the incorporation of lignin induces the initial decomposition (T5%) at a lower temperature; at the same time, maximum decomposition (Tmax) shifts to a higher temperature region and a higher amount of char residue is reported at the end of the test. Further, the TGA-FTIR study revealed that the ternary blends (i.e., the combination of LL or KL, ZnP, and PA11) released mainly the phosphinate compound, hydrocarbon species, and a small amount of phosphinic acid during the initial decomposition stage (T5%), while hydrocarbons, carbonyls, and phenolic compounds along with CO2 are released during main decomposition stage (Tmax). The analysis of decomposition products suggests the stronger bonds formation in the condensed phase and the obtainment of a stable char layer. Cone calorimetry exploited to study the fire behavior on sheet samples (polymer bulk) showed an improvement in flame retardant properties with increasing lignin content in blends and most enhanced results were found when 10 wt% of LL and ZnP were combined such as a reduction in heat release rate (HRR) up to 64% and total heat release (THR) up to 22%. Besides, tests carried out on knitted fabric structure showed less influence on HRR and THR but the noticeable effect on postponing the time to ignition (TTI) and reduction in the maximum average rate of heat emission (MARHE) value during combustion.
Assuntos
Desenho de Fármacos , Retardadores de Chama/análise , Lignina/química , Nylons/química , Ácidos Fosfínicos/química , Zinco/química , Cinética , Temperatura , TêxteisRESUMO
The use of biobased flame-retardant (FR) agents for reducing the flammability of polyester/cotton (T/C) blend fabrics is highly desirable. In this study, a novel and sustainable phosphorus/nitrogen-containing FR, namely, phytic acid-urea (PA-UR) salt, was synthesized. The PA-UR salt was further used to enhance the FR performance of T/C fabric through surface modification. We further explored the potential chemical structure of PA-UR and the surface morphology, thermal stability, heat release capacity, FR properties, and mode of action of the coated fabric. The coated fabric achieved self-extinguishing and exhibited an increased limiting oxygen index of 31.8%. Moreover, the coated T/C blend fabric demonstrated a significantly reduced heat release capacity, indicating a decreased fire hazard. Thermogravimetric analysis revealed the anticipated decomposition of the coated T/C blend fabric and a subsequent increase in thermal stability. The burned char residues also maintained their fiber shape structures, suggesting the presence of condensed FR actions in the PA-UR-coated T/C blend fabric.
RESUMO
Introduction: The oldest olds (aged 85 and over) are the fastest-growing age segment. However, our understanding of their mobility is limited. To address this gap, we invited 19 U.S. and 30 Chinese "oldest old" to take part in focus groups and complete a mobility questionnaire. We focus on travel mode choice, which includes changes in travel modes, frequency of usage, and perceptions of comfort. Methods: Older adults' familiarity and acceptance of new mobility technologies (e.g., ridesharing, carsharing, and autonomous vehicles) were measured by questionnaire and focus group. Word clouds were also used to illustrate people's reasons for choosing their primary mode of transportation. Results and discussion: The results show that both panels of older adults similarly feel some extent of travel limitations. But the responses among the two groups differ: 18 American participants chose "drive myself" as their primary option a decade ago, while 11 chose it now; no Chinese participants selected it either a decade ago or now. Both currently and 10 years ago, there was a significant difference in mode choice between participants in China and the United States. However, this gap has narrowed over the past decade. Participants in China have significantly changed their transportation preferences compared to 10 years ago, while participants in the US have remained nearly unchanged. American respondents consider "ease" as an important factor, while Chinese respondents pay more attention to "safety" and "no other option to get around" when making travel mode choices. Compared to Chinese participants, American participants were more comfortable with driving an autonomous vehicle. These differences may result from the various developmental stages and transportation policies of the two countries. This study supports the development of new mobility technologies for the oldest old to improve their quality of life.
Assuntos
Comportamento de Escolha , Grupos Focais , Meios de Transporte , Humanos , China , Estados Unidos , Masculino , Feminino , Inquéritos e Questionários , Idoso de 80 Anos ou mais , Viagem/psicologia , Condução de Veículo/psicologiaRESUMO
The durable flame-retardant functional coating of polyester/cotton (T/C) blend fabrics is both interesting and challenging. In this study, a novel in-situ polymerization strategy for phosphorus/nitrogen-based flame-retardant on T/C blend samples was developed through the polycondensation of tetramethylolphosphonium sulfate, dicyandiamide, and anionic cyclic phosphate ester. The chemical structure of the polycondensation compounds, as well as the surface morphology, combustion behavior, flame-retardant capacity, washing durability and flame-retardant mechanism of the coated T/C blend fabrics, were investigated. The coated T/C blend fabrics demonstrated excellent self-extinguishing performance, with the damaged length decreasing to as low as 8.0 cm and the LOI reaching 28 %. Moreover, the peak heat release rate of the coated T/C blend fabrics decreased by 39.7 %. The superior flame retardancy can be attributed to the enhanced dehydration and carbonization by phosphate groups in the condensed phase, as well as the quenching effect and diluting effect in the gas phase. Additionally, the coated T/C blend fabrics exhibited remarkable washing durability and still achieved self-extinguishing after 65 washing cycles, and the in-situ deposition of insoluble three-dimensional polycondensation compounds onto the T/C blend fabrics was beneficial. The flame-retardant coating had a minor impact on the whiteness, tensile strength and breathability of the T/C blend fabrics.
RESUMO
Smart materials demonstrate fascinating responses to environmental physical/chemical stimuli, including thermal, photonic, electronic, humidity, or magnetic stimuli, which have attracted intensive interest in material chemistry. However, their limited/harsh stimuli-responsive behavior or sophisticated postprocessing leads to enormous challenges for practical applications. Herein, we rationally designed and synthesized thermochromic Ni(II) organometallic [(C2H5)2NH2]2NiCl4-xBrx via a facile mechanochemical strategy, which demonstrated a reversible switch from yellow to blue color with a tunable phase-transition temperature from 75.6 to 61.7 °C. The simple electrospinning technology was applied to fabricate thermochromic Ni(II) organometallic-based nanofiber membranes for temperature monitoring. Furthermore, the organic charge-transfer cocrystal with a wide spectral absorption of 300-1950 nm and a high-efficiency photothermal conversion was combined with thermochromic Ni(II) organometallics for the desired dual-stimuli photo/thermochromism. This work supplies a new strategy for realizing multiple stimuli-responsive applications, such as thermal/light sensor displays and information storage.
RESUMO
Organic heterostructures (OHTs) with the desired geometry organization on micro/nanoscale have undergone rapid progress in nanoscience and nanotechnology. However, it is a significant challenge to elucidate the epitaxial-growth process for various OHTs composed of organic units with a lattice mismatching ratio of > 3%, which is unimaginable for inorganic heterostructures. Herein, we have demonstrated a vivid visualization of the morphology evolution of epitaxial-growth based on a doped interfacial-layer, which facilitates the comprehensive understanding of the hierarchical self-assembly of core-shell OHT with precise spatial configuration. Significantly, the barcoded OHT with periodic shells obviously illustrate the shell epitaxial-growth from tips to center parts along the seeded rods for forming the core-shell OHT. Furthermore, the diameter, length, and number of periodic shells were modulated by finely tuning the stoichiometric ratio, crystalline time, and temperature, respectively. This epitaxial-growth process could be generalized to organic systems with facile chemical/structural compatibility for forming the desired OHTs.
RESUMO
The fusion of the secretory vesicle with the plasma membrane requires the assembly of soluble N-ethylmaleimide-sensitive factor attachment protein receptor (SNARE) protein complexes formed by synaptobrevin, syntaxin-1, and SNAP-25. Within the pathway leading to exocytosis, the transitions between the "open" and "closed" conformations of syntaxin-1 function as a switch for the fusion of vesicles with the plasma membranes; rapid assembly and disassembly of syntaxin-1 clusters on the plasma membrane provide docking and fusion sites for secretory vesicles in neuroendocrine cells; and the fully zippered trans-SNARE complex, which requires the orderly, rapid and accurate binding of syntaxin-1 to other SNARE proteins, play key roles in triggering fusion. All of these reactions that affect exocytosis under physiological conditions are tightly regulated by multiple factors. Here, we review the current evidence for the involvement of syntaxin-1 in the mechanism of neuroendocrine cell exocytosis, discuss the roles of multiple factors such as proteins, lipids, protein kinases, drugs, and toxins in SNARE complex-mediated membrane fusion, and present an overview of syntaxin-1 mutation-associated diseases with a view to developing novel mechanistic therapeutic targets for the treatment of neuroendocrine disorders.
Assuntos
Células Neuroendócrinas , Sintaxina 1/genética , Proteínas Qa-SNARE/metabolismo , Células Neuroendócrinas/metabolismo , Proteínas R-SNARE , Exocitose/fisiologiaRESUMO
Nowadays, high value-added and multifunctional textiles have attracted widespread attention due to the changing demands of modern life. This study focused on the fabrication of silk with photochromism, flame retardancy, UV resistance and durability using riboflavin sodium phosphate (RSP) and various metal ions (Fe2+, Fe3+, Al3+, and Ti4+). Attractively, the photochromic performance was one of the most distinctive features of the modified silk, and the yellow silk fabric turned into fluorescent green under UV lamp. After a detailed comparison, it was determined that RSP/Fe3+ hybrid system was most effective in improving anti-UV performance of the silk with a high UPF of 25.8, achieving a "Good" level of UV protection. Specifically, it achieved a B1 fire protection with a low damaged-length of 9.4 cm and a high LOI of 28.3 %. Additionally, the modified silk showed the lowest smoke density, reducing by approximately 84.1 % versus that of pristine silk. Moreover, the modified silk was able to meet the B1 classification and the "Good" UV protection requirements even after 75 washing cycles, making it more durable than most functional textiles reported. The further analysis indicated that RSP and metal ions can synergistically enhance the condensed-phase action, thereby improving the fire resistance of silk.
Assuntos
Seda , Têxteis , Têxteis/análise , ÍonsRESUMO
An increasing interest is focused on the application of 3D printing for sensor manufacturing. Using 3D printing technology offers a new approach to the fabrication of sensors that are both geometrically and functionally complex. This work presents the analysis of the 3D-printed thermoplastic nanocomposites compress under the applied force. The response for the corresponding resistance changes versus applied load is obtained to evaluate the effectiveness of the printed layer as a pressure/force sensor. Multi-walled carbon nanotubes (MWNT) and high-structured carbon black (Ketjenblack) (KB) in the polylactic acid (PLA) matrix were extruded to develop 3D-printable filaments. The electrical and piezoresistive behaviors of the created 3D-printed layers were investigated. The percolation threshold of MWNT and KB 3D-printed layers are 1 wt.% and 4 wt.%, respectively. The PLA/1 wt.% MWNT 3D-printed layers with 1 mm thickness exhibit a negative pressure coefficient (NPC) characterized by a decrease of about one decade in resistance with increasing compressive loadings up to 18 N with a maximum strain up to about 16%. In the cyclic mode with a 1 N/min force rate, the PLA/1 wt.% MWNT 3D-printed layers showed good performance with the piezoresistive coefficient or gauge factor (G) of 7.6 obtained with the amplitude of the piezoresistive response (Ar) of about -0.8. KB composites could not show stable piezoresistive responses in a cyclic mode. However, under high force rate compression, the PLA/4 wt.% KB 3D-printed layers led to responses of large sensitivity (Ar = -0.90) and were exempt from noise with a high value of G = 47.6 in the first cycle, which is a highly efficient piezoresistive behavior.
RESUMO
Numerous drugs are used during caesarean sections to provide regional and general anaesthesia. Dexmedetomidine has been used in some recent obstetric trials, but there are concerns about postpartum changes in uterine contractions. This study evaluated the effect of dexmedetomidine on oxytocin-induced uterine contractions in women undergoing caesarean section. Sixty women undergoing caesarean section in Lianyungang Second People's Hospital were randomly assigned to dexmedetomidine (group D, n = 30) or saline (group C, n = 30) groups. Equal volumes of saline or dexmedetomidine were administered intravenously (IV). During the intraoperative delivery of the foetus and placenta, oxytocin was administered to promote contractions. Heart rate (HR), systolic blood pressure (SBP), diastolic blood pressure (DBP) and mean arterial pressure (MAP) were compared. The Ramsay scale was used to assess sedation, while the Tsai and Chu methods assessed shivering. Adverse intraoperative events were observed. All variables fluctuated significantly after anaesthesia onset in both groups but were most pronounced in group D. The VAS, Ramsay and shivering scores were significantly lower in group D compared to group C. During rapid IV infusion of oxytocin after foetal delivery, the incidence of nausea, vomiting, chest tightness and hypotension was significantly lower in group D than in group C.
Assuntos
Cesárea , Dexmedetomidina , Anestesia Geral/efeitos adversos , Dexmedetomidina/efeitos adversos , Feminino , Humanos , Ocitocina , Gravidez , Contração UterinaRESUMO
Polyester/cotton (T/C) blend fabrics are highly flammable due to the particular "scaffolding effect". In this work, an intumescent flame retardant (IFR) agent containing P, N, and B was designed and synthesized using bio-based phytic acid, pentaerythritol, boric acid, and urea. The IFR compounds were deposited onto a T/C blend fabric by the surface-coating route. The chemical structure of IFR agent and its potential cross-linking reactions with T/C fibers were characterized. The morphology, thermal stability, heat-release ability, flame retardancy, and mechanism of coated T/C blend fabrics were explored. The self-extinguishing action was observed for the coated T/C blend fabric with a weight gain of 13.7%; the limiting oxygen index (LOI) value increased to 27.1% versus 16.9% for a pristine one. Furthermore, the intumescent flame retardant (IFR) coating imparted T/C blend fabrics with high thermal stability and significantly suppressed heat release by nearly 50%. The char residue analyses on morphology and element content confirmed the intumescent FR action for coated T/C blend fabrics. The prepared IFR coating has great potential to serve as an eco-friendly approach for improving the flame retardancy of T/C blend textiles.
RESUMO
Nerve guidance conduits (NGCs) have attracted much attention due to their great necessity and applicability in clinical use for the peripheral nerve repair. Great efforts in recent years have been devoted to the development of high-performance NGCs using various materials and strategies. The present review provides a comprehensive overview of progress in the material innovation, structural design, advanced engineering technologies and multi functionalization of state-of-the-art nerve guidance conduits NGCs. Abundant advanced engineering technologies including extrusion-based system, laser-based system, and novel textile forming techniques in terms of weaving, knitting, braiding, and electrospinning techniques were also analyzed in detail. Findings arising from this review indicate that the structural mimetic NGCs combined with natural and synthetic materials using advanced manufacturing technologies can make full use of their complementary advantages, acquiring better biomechanical properties, chemical stability and biocompatibility. Finally, the existing challenges and future opportunities of NGCs were put forward aiming for further research and applications of NGCs.
RESUMO
The immobilization of biocatalysts or other bioactive components often means their transformation from a soluble to an insoluble state by attaching them to a solid support material. Various types of fibrous textiles from both natural and synthetic sources have been studied as suitable support material for biocatalysts immobilization. Strength, inexpensiveness, high surface area, high porosity, pore size, availability in various forms, and simple preparation/functionalization techniques have made textiles a primary choice for various applications. This led to the concept of a new domain called-biocatalysts immobilization on textiles. By addressing the growing advancement in biocatalysts immobilization on textile, this study provides the first detailed overview on this topic based on the terms of preparation, progress, and application in wastewater treatment. The fundamental reason behind the necessity of biocatalysts immobilized textile as well as the potential preparation methods has been identified and discussed. The overall progress and performances of biocatalysts immobilized textile have been scrutinized and summarized based on the form of textile, catalytic activity, and various influencing factors. This review also highlighted the potential challenges and future considerations that can enhance the pervasive use of such immobilized biocatalysts in various sustainable and green chemistry applications.
Assuntos
Têxteis , Purificação da Água , Enzimas ImobilizadasRESUMO
Bioluminescent living organisms emit light through a specific biocatalyzed reaction involving a luciferin substrate and a luciferase enzyme. The present work investigated the possibility of creating optimal luminescence by immobilization of one or both the enzymes Luciferase (Luc) and FMN reductase (Red) involved in a bioluminescent bacterial system onto a plasma-activated microfibrous PET nonwoven. Parameters affecting the catalytic activity and efficiency of the bacterial system in aqueous medium were determined by luminescence intensity measurements using a luminometer. Two types of plasma, air atmospheric plasma (ATMP) and cold remote plasma (CRPNO) treatment, were used to activate the PET nonwoven. Further, one or both enzyme(s) were immobilized using a physical adsorption technique, without or with the use of natural biopolymers (gelatin and starch) and bovine serum albumin-BSA protein, to improve enzyme stability and activity. Coimmobilization of both Red and Luc enzymes on the CRPNO plasma-activated nonwoven in the presence of BSA led to the maximum luminescence. As high as 60,000 RLU equivalent to that of an LED light used for calibration was observed and showed stable intensity up to 6 min. Fiber surface analysis was tested using wettability tests (water contact angle and capillary uptake), while scanning electron microscopy, atomic force microscopy, and electron spectroscopy for chemical analysis showed changes in fiber surface morphology and chemical functional groups. A considerable increase in "N" atom content after coimmobilization of enzymes in the presence of BSA was detected. This study is the first successful attempt to use a biomimetic strategy for immobilization of enzymes involved in bacterial luminescence on a plasma-activated microfibrous nonwoven in an attempt to attain bioluminescent materials.
RESUMO
3D printing utilized as a direct deposition of conductive polymeric materials onto textiles reveals to be an attractive technique in the development of functional textiles. However, the conductive fillers-filled thermoplastic polymers commonly used in the development of functional textiles through 3D printing technology and most specifically through Fused Deposition Modeling (FDM) process-are not appropriate for textile applications as they are excessively brittle and fragile at room temperature. Indeed, a large amount of fillers is incorporated into the polymers to attain the percolation threshold increasing their viscosity and stiffness. For this reason, this study focuses on enhancing the flexibility, stress and strain at rupture and electrical conductivity of 3D-printed conductive polymer onto textiles by developing various immiscible polymer blends. A phase is composed of a conductive polymer composite (CPC) made of a carbon nanotubes (CNT) and highly structured carbon black (KB)- filled low-density polyethylene (LDPE) and another one of propylene-based elastomer (PBE) blends. Two requirements are essential to create flexible and highly conductive monofilaments for 3D-printed polymers onto textile materials applications. First, the co-continuity of both the thermoplastic and the elastomer phases and the location of the conductive fillers in the thermoplastic phase or at the interface of the two immiscible polymers are necessary to preserve the flexibility of the elastomer while decreasing the global amount of charges in the blends. In the present work based on theoretical models, when using a two-step melt process, the KB and CNT particles are found to be both preferentially located at the LDPE/PBE interface. Moreover, in the case of the two-step extrusion, SEM characterization showed that the KB particles were located in the LDPE while the CNT were mainly at the LDPE/PBE interface and TEM analysis demonstrated that KB and CNT nanoparticles were in LDPE and at the interface. For one-step extrusion, it was found that both KB and CNT are in the PBE and LDPE phases. These selective locations play a key role in extending the co-continuity of the LDPE and PBE phases over a much larger composition range. Therefore, the melt flow index and the electrical conductivity of monofilament, the deformation under compression, the strain and stress and the electrical conductivity of the 3D-printed conducting polymer composite onto textiles were significantly improved with KB and CNT-filled LDPE/PBE blends compared to KB and CNT-filled LDPE separately. The two-step extrusion processed 60%(LDPE16.7% KB + 4.2% CNT)/40 PBE blends presented the best properties and almost similar to the ones of the textile materials and henceforth, could be a better material for functional textile development through 3D printing onto textiles.
RESUMO
Flavin mononucleotide (biobased flavin), widely known as FMN, possesses intrinsic fluorescence characteristics. This study presents a sustainable approach for fabricating color-changing intensified light-emitting textiles using the natural compound FMN via digital printing technologies such as inkjet and chromojet. The FMN based ink formulation was prepared at 5 different concentrations using water and glycerol-based systems and printed on cotton duck white (CD), mercerized cotton (MC), and polyester (PET) textile woven samples. After characterizing the printing inks (viscosity and surface tension), the photophysical and physicochemical properties of the printed textiles were investigated using FTIR, UV/visible spectrophotometry, and fluorimetry. Furthermore, photodegradation properties were studied after irradiation under UV (370 nm) and visible (white) light. Two prominent absorption peaks were observed at around 370 nm and 450 nm on K/S spectral curves because of the functionalization of FMN on the textiles via digital printing along with the highest fluorescence intensities obtained for cotton textiles. Before light irradiation, the printed textiles exhibited greenish-yellow fluorescence at 535 nm for excitation at 370 nm. The fluorescence intensity varied as a function of the FMN concentration and the solvent system (water/glycerol). With 0.8 and 1% of FMN, the fluorescence of the printed textiles persisted even after prolonged light irradiation; however, the fluorescence color shifted from greenish-yellow color to turquoise blue then to white, with the fluorescence quantum efficiency values (φ) increasing from 0.1 to a value as high as 1. Photodegradation products of the FMN with varying fluorescence wavelengths and intensities would explain the results. Thus, a color-changing light-emitting fluorescent textile was obtained after prolonged light irradiation of textile samples printed using biobased flavin. Furthermore, multifunctional properties such as antibacterial properties against E. coli were observed only for the printed cotton textile while increased ultraviolet protection was observed for both cotton and polyester printed fabrics for the high concentration of FMN water-based and glycerol-based formulations. The evaluation of fluorescence properties using digital printing techniques aimed to provide more sustainable solutions, both in terms of minimum use of biobased dye and obtaining the maximum yield.
RESUMO
The underlying mechanisms of recurrence and metastasis of epithelial ovarian cancer (EOC) are largely unknown. In the present study, we investigated the clinical significance of microRNA-125b (miR-125b) and its role in ovarian tumorigenesis and progression. Seventy patients of EOC and paired tissues were enrolled from 2015 to 2017. qRT-PCR was used to evaluate miR-125b expression in tumor tissues and EOC cell line. Gain-and-loss function of miR-125b was achieved to explore the changes in cell biological function. We found that miR-125b expression in EOC tissues, especially in the high-grade tissues (P < 0.001), was significantly lower compared to the matched adjacent noncancerous tissues and associated with pathological type, stage, and overall survival (P < 0.05). Upregulation of miR-125b promoted apoptosis and decreased cell survival rate and migration, and vice versa in vitro. Mechanistically, miR-125b negatively regulated S100A4, a metastasis-associated protein. MiR-125b overexpression significantly decreased tumor growth and inhibited lung metastasis in vivo. Our results supported that miR-125b contributes to the progression of EOC by targeting S100A4. It potentially acts as a potential biomarker and therapeutic target of EOC.
Assuntos
Carcinoma Epitelial do Ovário/genética , Carcinoma Epitelial do Ovário/patologia , MicroRNAs/metabolismo , Neoplasias Ovarianas/genética , Neoplasias Ovarianas/patologia , Adolescente , Adulto , Idoso , Animais , Apoptose/genética , Apoptose/fisiologia , Feminino , Humanos , Camundongos , MicroRNAs/genética , Pessoa de Meia-Idade , Reação em Cadeia da Polimerase Via Transcriptase Reversa , Proteína A4 de Ligação a Cálcio da Família S100/genética , Proteína A4 de Ligação a Cálcio da Família S100/metabolismo , Adulto JovemRESUMO
Long non-coding RNA LOC285194 (LOC285194) has reported to regulate vascular smooth muscle cells (VSMCs) proliferation and apoptosis in vitro and in vivo. Here we aimed to determine the role of LOC285194 in the proliferation, migration and apoptosis of VSMCs and its underlying mechanisms. A7r5 cells were transfected with Lv-LOC285194 or control Lv-NC for 24-72 h, or small interfering RNA targeting S100A4 (S100A4 siRNA) for 24-48 h, or co-transfected with Lv-LOC285194 and PUMA siRNA for 72 h, or treated with miR-211 inhibitor or co-transfected with Lv-LOC285194 and miR-211 mimics for 72 h. A7r5 cells were also treated with transforming growth factor - ß(TGF-ß) (5 ng/ml) after Lv-LOC285194 transfection for 24 h. The relationship between LOC285194 and TGF-ß was confirmed using luciferase reporter assay. Cell proliferation and cell apoptosis were analyzed by Cell Counting Kit-8 (CCK-8) assay, ELISA and TUNEL staining. LOC285194 and miR-211 expression were detected by qPCR assay. S100A4, pro-apoptotic and anti-apoptotic protein were detected by Western blot assay. LOC285194 inhibited cell proliferation, invasion and migration and promoted cell apoptosis accompanied by upregulation of PUMA and downregulation of miR-211 and S100A4. Targeting PUMA reversed the effect of LOC285194 on cell apoptosis and proliferation. miR-211 mimic inhibited LOC285194-induced PUMA upregulation and decreased LOC285194-induced cell apoptosis. TGF-ß (5 ng/ml) treatment reversed S100A4 siRNA or LOC285194-induced S100A4 expression. Luciferase reporter assay showed that TGF-ß was the target of LOC285194. LOC285194 inhibits proliferation and promoted apoptosis in vascular smooth muscle cells via targeting miR-211/PUMA signal; In addition, LOC285194 decreased cell invasion and migration by targeting TGF-ß1/S100A4 signal.