Effects of exogenous N-acyl homoserine lactones (AHLs) on methanogenic activities and microbial community differences during anaerobic digestion.

N-acyl homoserine lactones (AHLs) function as signaling molecules influencing microbial community dynamics. This study investigates the impact of exogenously applied AHLs on methane production during waste-activated sludge (WAS) anaerobic digestion (AD). Nine AHL types, ranging from 10-4 to 10 µg/g VSS, were applied, comparing microbial community composition under optimal AHL concentrations. Firmicutes, Bacteroidetes, Chloroflexi, and Proteobacteria were identified in anaerobic digesters with C4-HSL, C6-HSL, and C8-HSL. Compared to the control, Halobacterota increased by 19.25%, 20.87%, and 9.33% with C7-HSL, C10-HSL, and C12-HSL. Exogenous C7-HSL enhanced the relative abundance of Methanosarcina, Romboutsia, Sedimentibacter, Proteiniclasticum, Christensenellaceae_R-7_group. C10-HSL increased Methanosarcina abundance. C4-HSL, C6-HSL, C8-HSL, C10-HSL, and C12-HSL showed potential to increase unclassified_Firmicutes. Functional Annotation of Prokaryotic Taxa (FAPROTAX) predicted AHLs' impact on related functional genes, providing insights into their role in AD methanogenesis regulation. This study aimed to enhance the understanding of the influence of different types of exogenous AHLs on AD and provide technical support for regulating the methanogenesis efficiency of AD by exogenous AHLs.

Effect of granular activated carbon and chloroform on chain elongation with simple substrate ethanol and acetate.

Chain elongation is a promising technology for production of medium-chain fatty acids (MCFAs). Granular activated carbon (GAC) is commonly used in anaerobic fermentation. Low level CHCl3 can inhibit methanogenesis and homoacetogenesis at the same time. However, the effect of them on chain elongation performance with highly enriched consortia and simple substrate (i.e., ethanol and acetate) was still unclear. Hence, the effects of CHCl3 and on MCFAs production and the microbial community was studied here. CHCl3 displayed fatal effect on chain elongation system when its concentration was higher than 0.1% v/v. 0.05% v/v CHCl3 was enough to inhibit homoacetogens and further decreased the caproate production efficiency without altering the core bacteria tremendously. GAC was found to be adverse for chain elongation with simple substrate (i.e., ethanol and acetate) and highly enriched microbial consortia dominated by Clostridium sensu stricto, less than 20% electrons were finally distributed in caproate. It might be attributed to other electron consuming activities induced by GAC.

Revealing the mechanism of novel nitrogen-doped biochar supported magnetite (NBM) enhancing anaerobic digestion of waste-activated sludge by sludge characteristics.

Anaerobic digestion (AD) is a promising technology in waste treatment and energy recovery. However, it suffers from long retention time and low biogas yield. In this study, novel nitrogen-doped biochar supported magnetite (NBM) was synthesized and applied to enhance the AD of waste-activated sludge. Results showed that NBM increased cumulative methane production and SCOD removal efficiency by up to 1.75 times and 15% respectively at 5 g/L compared with the blank. NBM enhanced both hydrolysis and methanogenesis process during AD and the activities of α-glucosidase, protease, coenzyme F420 and electron transport system were increased by 19%, 163%, 104% and 160% respectively at 5 g/L NBM compared with the blank. NBM also facilitated the secretion of conductive protein in extracellular polymeric substances as well as the formation of conductive pili, leading to 3.18-7.59 times higher sludge electrical conductivity. Microbial community analysis revealed that bacteria Clostridia and archaea Methanosarcina and Methanosaeta were enriched by the addition of NBM, and direct interspecies electron transfer might be promoted between them. This study provides a practical reference for future material synthesis and its application.

New insight into degradation of chloramphenicol using a nanoporous Pd/Co3O4cathode: characterization and pathways analysis.

The growing chloramphenicol (CAP) in wastewater brought a serious threat to the activity of activated sludge and the spread of antibiotics resistance bacteria. In this study, a highly ordered nanoporous Co3O4layer on Co foil through anodization was prepared as cathode for nitro-group reduction and electrodeposited with Pd particles for dechlorination to reduce CAP completely. After 3 h treatment, almost 100% of CAP was reduced. Co2+ions in Co3O4served as catalytic sites for electrons transfer to CAP through a redox circle Co2+-Co3+-Co2+, which triggered nitro-group reduction at first. With the presence of Pd particles, more atomic H* were generated for dechlorination, which increased 22% of reduction efficiency after 3 h treatment. Therefore, a better capacity was achieved by Pd/Co3O4cathode (K = 0.0245 min-1,Kis reaction constant) than by other cathodes such as Fe/Co3O4(K = 0.0182 min-1), Cu/Co3O4(K = 0.0164 min-1), and pure Co3O4(K = 0.0106 min-1). From the proposed reaction pathway, the ultimate product was carbonyl-reduced AM (dechlorinated aromatic amine product of CAP) without antibacterial activity, which demonstrated this cathodic technology was a feasible way for wastewater pre-treatment.

Impact of magnesium ions on lysozyme-triggered disintegration and solubilization of waste activated sludge.

Lysozyme can efficiently accelerate solubilization and hydrolysis of waste activated sludge (WAS) for anerobic digestion. However, the effect of lysozyme was easily to be inhibited by metal ions in WAS. The impact of magnesium ions (Mg2+) on lysozyme catalyze WAS disintegration was investigated in this study. The effect of lysozyme on WAS hydrolysis could be hindered by Mg2+. Relatively high concentrations (>50 mg/L) of Mg2+ in sludge significantly reduced the release of soluble polysaccharides and proteins from WAS, while sulfate ions or chloride ions caused no such effect. Proteins were difficult to be extracted from extracellular polymeric substances (EPS) of WAS in the presence of Mg2+ (>10 mg/L) due to the divalent cation bridging (DCB) behavior, while the extraction of polysaccharides was not significantly affected. The polysaccharides and proteins in the inner EPS layer were transferred to the outer layer during the lysozyme treatment, and total quantities of both components maintained constantly. At least 23.1% lysozymes were trapped in the liquid phase of 100 mg Mg2+/L in the first hour. Mg2+ could significantly affect the transfer of lysozyme from liquid phase to the inner layer of sludge. Mg2+ neutralized the negative surface charge of the sludge particles, which hindered the absorption of positively charged lysozyme molecules by sludge flocs from the liquid phase. The proteins of TB-EPS had higher ratios of α-helixes and tighter structures than those in LB-EPS, which could impede the lysozyme transfer to the cell wall.

New insight into enhanced short-chain fatty acids production from waste activated sludge through pretreatment of cation exchange resin coupled NaCl addition.

In this study, a novel pretreatment of cation exchange resin (CER) coupled NaCl addition was proposed to enhance waste activated sludge (WAS) hydrolysis and promote short-chain fatty acids (SCFAs) production in the anaerobic fermentation process. At the optimal pretreatment condition of 3 g/g SS CER and 15 g/L NaCl, considerable SCOD (i.e. 5107 mg/L, 35.4% of TCOD) was released after 2-day coupled treatment, which provided sufficient organic substance for the subsequent SCFAs production. The sludge hydrolysis mechanism was illustrated, i.e. CER triggered extracellular polymeric substances (EPS) disruption and NaCl induced microbial cells lysis. The synergistic interaction between CER and NaCl pretreatment was investigated and application potential of fermentative liquid was evaluated after the coupled pretreatment-enhanced anaerobic fermentation. In the presence of abundant biodegradable substrates in the fermentative liquid, 4742 mg COD/L (i.e. 388 mg COD/g VSS) of SCFAs production was achieved within 6-day anaerobic fermentation, mainly composed of acetic and propionic acids (70.4% of total SCFAs).

Integration of a pure moving bed biofilm reactor process into a large micro-polluted water treatment plant.

The pure-MBBR process was applied to remove ammonia in a full-scale micro-polluted-water treatment plant with a daily treatment capacity of 260 × 104 m3/d, Guangdong, China. The relationship between treatment efficiency, physical and chemical properties and microbial diversity in the process of biofilm growth was explored, and the oxygen transfer model of biofilm was established. The results show that the effluent of two-stage pure MBBR process is stable and up to standard after 10 days' incubation. The nitrification loads of two-stage biofilm was stable on the 14th day. The biomass and biofilm thickness lagged behind the nitrification load, and reached a relatively stable level on the 28th day. The species richness of biofilm basically reached a stable level on the 21st day, and the microbial diversity of primary biofilm was higher. In the primary and secondary stage at different periods, the relative abundance of dominant nitrifying bacteria Nitrospira reaches 8.48-13.60%, 6.48-9.27%, and Nitrosomonas reaches 2.89-5.64%, 0.00-3.48%. The pure MBBR system mainly adopts perforated aeration. Through the cutting and blocking of bubbles by suspended carriers, the oxygen transfer rate of the system was greatly improved.

Exploiting community structure, interactions and functional characteristics of fungi involved in the biodrying of storage sludge and beer lees.

In this study, the dynamic changes in fungal biodiversity, community structure, fungal associations and functional characteristics were investigated in the biodrying of storage sludge and beer lees by using high throughput sequencing, network and correlation matrix analyses, and FUNGuild database. Additionally, a hypothetical model was provided to better understand the biodrying system. The results showed that fungal diversity decreased after biodrying, while community richness increased in the mesophilic stage and decreased as biodrying progressed. Fungal communities differed in different stages of the biodrying process. Ascomycota and Basidiomycota were the dominant phyla throughout the biodrying process, while Pichia was the dominant genus in the thermophilic stage. Network and correlation matrix analyses provided useful tools for insight into the fungal interactions, allowing us to propose a conceptual model of how succession in fungal associations regulates the dynamics of biodrying systems. Biodrying treatment had a significant effect on fungal trophic modes, with most pathogenic fungi fading away over the process, illustrating that biodrying is an effective bio-treatment method to eliminate pathogenic fungi. These findings provide information that elucidates the fungal interactions and functional characteristics during the biodrying process.

The characteristics of heat-driven ammonium adsorption in aerobic granular sludge.

Adsorption is an important step during the migration of ammonium from the aqueous phase to biomass in biological nitrogen removal processes. A deeper understanding of the adsorption mechanisms is encouraged in constructing nitrogen conversion models. In this study, the ammonium adsorption in aerobic granular sludge was investigated at different conditions. Analysis of kinetic data indicated that ammonium adsorption was a fast process and followed pseudo-second-order kinetics (adsorption rate constant k2 was between 0.031 and 0.065 g/(mg · min)). The maximum adsorption capacity and half saturation constant KL in the Langmuir isotherm model were 4.95 mgNH4 +-N/g total suspended solids and 0.0126 L/mg, respectively. Effects of environmental conditions such as temperature, pH and competitive cations were also estimated. The optimum pH was 7 and the effects of competitive cations were in the order Ca2+ > Mg2+ > K+ > Na+. Values of thermodynamic parameters (ΔHƟ = -14.697 kJ/mol, ΔSƟ = -6.65 J/(mol · K)) indicated that the adsorption process was spontaneous and exothermic. Desorption tests showed that the process was reversible and low temperature had a negative effect on ammonium desorption. These findings could be useful for completing the mathematical model of the nitrogen removal process in bioreactors.

Variations regularity of microorganisms and corrosion of cast iron in water distribution system.

Corrosion, one of the most common problems of metal pipe for water supply, generally leads to poor water quality, bacteria proliferation, water capacity decrease and other problems. As microorganisms affect corrosion by changing the characteristics of metal surface, the mechanism of microbial corrosion still remains unclear. The corrosion behavior of ductile cast iron is implemented in the dynamic flow and static conditions, in which variations of water quality and microbial community are analyzed in details. The results show that if the corrosion rate of ductile cast iron decreases, the corrosion of cast iron will result in a lower DO and a higher total iron in bulk water. The number of microorganisms is not a decisive factor of corrosion, even though the counts of bacteria had a close relationship with DO. On the basis of the detection of the 10 kinds of nitrate-reducing bacteria by Miseq sequencing, NRB of the biofilm biomass accounts for 18.3% on the 30th day and 20.5% on the 55th day. Even though aerobic NRBs go into the biofilm later than the facultative anaerobic NRBs, the growth of the anaerobic NRBs is not affected.

Biofouling control by biostimulation of quorum-quenching bacteria in a membrane bioreactor for wastewater treatment.

Bacterial quorum quenching (QQ) has been shown to be effective in controlling biofouling in membrane bioreactors (MBRs) for wastewater treatment. However, the encapsulation of a sufficient level of QQ bacteria is complicated and difficult. In plant research, gamma-caprolactone (GCL), which is structurally similar to the quorum signal, N-acyl homoserine lactone (AHL), was successfully used to specifically stimulate AHL-degrading bacteria (biostimulation) in hydroponic systems to control blackleg and soft rot diseases in potato. In this study, the feasibility of enriching QQ bacteria from activated sludge by GCL was examined, and the effect of biostimulation on biofouling control in MBR treating domestic wastewater was investigated. The results showed that after enrichment with GCL, activated sludge could effectively degrade AHLs, and a QQ gene (qsdA) was augmented. The proposed biostimulation QQ strategy, by introducing and continuously dosing GCL, could significantly increase QQ activity, decrease AHL, control the secretion of extracellular polymeric substances (EPS), and thus, effectively control biofouling in an MBR. This biostimulation QQ strategy provides a more convenient option for biofouling control in MBR applications. Biotechnol. Bioeng. 2016;113: 2624-2632. © 2016 Wiley Periodicals, Inc.

Raman Spectra of Bredigite at High Temperature and High Pressure.

Bredigite was synthesized by using the Piston-Cylinder in 1.2 GPa and 1 473 K. With external heating device and diamond anvil cell, high temperature and high pressure Raman spectra of bredigite were collected at temperatures 298, 353, 463, 543, 663, 773 and 873 K and with pressure from 1 atm up to 14.36 GPa (room temperature). The SEM image showed that the sample consisted of one crystalline phase with grain size ranging from 10～20 µm. The EPMA data suggest a chemical formula of Ca7.03(2)Mg0.98(2)Si3.94(2)O16 which was identical to the theoretical component of bredigite. The Raman spectroscopic results indicate there were 29 vibration bands of bredigite at high temperature. Some bands were merging, weakening and disappearing increasingly with the temperature, which was obvious in the range of 800~1 200 cm-1. The vibration bands of 909, 927 and 950 cm-1 disappeared at 873, 773 and 873 K, respectively. The results primarily indicated that the structure of bredigite was stable under experimental condition. In addition, isobaric mode-Grüneisen parameters and isothermal mode-Grüneisen parameters were calculated, yielding 1.47(2) and 0.45(3) as their mean values, respectively. Anharmonic coefficients were estimated based on the high temperature and high pressure Raman experiments, showing that the contributions to anharmonic-effect induced with the Si­O vibration modes were smaller than other modes.

[Study on Mineralogical Characteristics of Quartz and Calcite from Feieling Skarn-Type Pb-Zn Deposit in Southwest Margin of Yunkai Massif].

The Feieling Pb-Zn deposit of skarn-type is located the in Southwest margin of Yunkai massif, China. This ore deposit can be divided into wall rock near ore, concealed rock mass, endoskarn, exoskarn and orebody. The Raman and FTIR spectrum are conducted to study the mineralogical characteristics of quartz and calcite from five types of rocks from Feieling skarn-type deposit. The analysis shows that the quartz included in the near ore wall rock, endoskarn and exoskarn, comparing with recrystallized quartz of concealed rock mass, has a tend to change into low symmetry quartz in varying degrees. The crystalinity and order degree of quartz from near ore wall rock to concealed rock mass and to endoskarn are becoming higher, but that of quartz from different exoskarn samples display no regular. The origin or the quartz microstructure changes may be related to the multi-stage evolution of skarn mineralization process. The quartz, included in near ore wall rock, endoskarn and exoskarn, become easier to recrystallize and adjust microstructure under the influence of the multi-stage hydrothermal and temperature effect. In anyone sample, the earlier crystalline calcite, showing subhedral-euhedral crystal, display higher crystalinity and order degree. On the contrary, the later crystalline calcite, showing xenomorphic crystal, display lower crystalinity and order degree. Calcite crystal of exoskarn rock contains some silica impurity, while endoskarn and orebody rock is pure. The purity of calcite crystal may relate to Multi-stage evolution of skarn mineralization process. At the early and late skarn stage, active silica-containing fluid is easier to join into calcite, which is under higher temperature environments. On the contrary, at the late quartz-surfide stage, the later crystalized calcite displays higher purity, which is under lower temperature environments. Therefore, spectral characteristics of quartz and calcite reflect multi-stage evolution of skarn mineralization process.

Distribution, microfabric, and geochemical characteristics of siliceous rocks in central orogenic belt, China: implications for a hydrothermal sedimentation model.

Marine siliceous rocks are widely distributed in the central orogenic belt (COB) of China and have a close connection to the geological evolution and metallogenesis. They display periodic distributions from Mesoproterozoic to Jurassic with positive peaks in the Mesoproterozoic, Cambrian--Ordovician, and Carboniferous--Permian and their deposition is enhanced by the tensional geological settings. The compressional regimes during the Jinning, Caledonian, Hercynian, Indosinian, and Yanshanian orogenies resulted in sudden descent in their distribution. The siliceous rocks of the Bafangshan-Erlihe ore deposit include authigenic quartz, syn-depositional metal sulphides, and scattered carbonate minerals. Their SiO2 content (71.08-95.30%), Ba (42.45-503.0 ppm), and ΣREE (3.28-19.75 ppm) suggest a hydrothermal sedimentation origin. As evidenced by the Al/(Al + Fe + Mn), Sc/Th, (La/Yb) N, and (La/Ce) N ratios and δCe values, the studied siliceous rocks were deposited in a marginal sea basin of a limited ocean. We suggest that the Bafangshan-Erlihe area experienced high- and low-temperature stages of hydrothermal activities. The hydrothermal sediments of the former stage include metal sulphides and silica, while the latter was mainly composed of silica. Despite the hydrothermal sedimentation of the siliceous rocks, minor terrigenous input, magmatism, and biological activity partly contributed to geochemical features deviating from the typical hydrothermal characteristics.

[Micro-area characteristics of laminated chert in the volcanic rocks of Xionger Group of Ruyang area and its geological significances].

The Xionger Group was originated from the volcanic eruption and sedimentation in Precambrian, whose sedimentary strata at the top were named Majiahe Formation. In the Majiahe Formation, there were hydrothermal chert widely distributed, which were exhibited to be interlayers in the volcanic rocks. The polarized microscope, X-ray diffraction (XRD), Raman and electron back scatter diffraction (EBSD) were conducted to study the characteristics in micro area of the jasperite samples, which were from the sedimentary interlayers in the volcanic rocks of Majiahe Formation in Xionger Group. As shown in the microphotographs and EBSD images, the quartz in the chert had small grain size, low degree of crystallinity and close packed structure, which quite agreed with the characteristics of hydrothermal sedimentary chert. In the chert of Xionger Group, there were clear banded (or lamellar) structures which were contributed by the diversities of the grain size and mineral composition. The different bands (or lamellars) had alternative appearance repeatedly, and denoted the diversities and periodic changes in the substance supply during the precipitation. According to the results of the XRD analysis, the majority minerals of the chert was low temperature quartz, whose lattice parameters were a=b=0.4913 nm, c=0.5405 nm and Z=3. As denoted in the EBSD image and result of Raman analysis, several impurity minerals were formed in the chert in different stages, whose geneses and formation time were quite different. The clay minerals and pyrite were scattered in distribution, and should be contributed by the original sedimentation. On contrary, the felsic minerals and mafic silicate minerals were originated from the sedimentation of tuffaceous substance during the volcanic eruption. The minerals of volcanic genesis had relatively larger grain size, and they deposited together with the hydrothermal sediments to form the bands (or lamellars) of coarse minerals. However, the hydrothermal sedimentation contributed to the bands (or lamellars) with minerals of much smaller grain size, which therefore resulted in diversities from the other bands (or lamellars). According to this, the repeated bands (or lamellars) denoted the volcanic activities were cyclic during the formation of the chert. What's more, the carbonate vein came from the precipitation of subsequent hydrothermal fluids in the fracture of the chert, which contributed to the changes (e. g. rising in crystallinity degree of silica and formation of micro-structure of new silicate) near the interface between chert and the carbonate vein. Although there were many impurity minerals with complex genesis, the relatively lower content of silica in the chert of Xionger Group was due to the volcanic mineral mainly. Since there were impurity minerals of volcanic genesis in relatively large amount, the content of silica in the chert of Xionger Group was hence relatively low. In this study, the Raman analysis was witnessed to be an effective way in the researches on the chert, and could open out the type of mineral, micro-structure and degrees of crystallinity (or order). These characteristics were well kept in the micro-area, and played significant roles to reflect and understand the formation mechanism and subsequent evolution of the chert.

Innovative cation exchange-driven carbon migration and recovery patterns in anaerobic fermentation of waste activated sludge.

Despite numerous treatments have been developed to enhance anaerobic fermentation of waste activated sludge, the innovative cation exchange (CE) approach has been rarely reported, little attempt was conducted to revealcarbon source fate. The interphase carbon balance was illustrated to clarify endogenous carbon dissolution, biotransformation,and recovery patterns. By CE-mediated divalent cation removal, almost 34.72 % of particulate carbon sources were dissolved in 2-day treatment, corresponding to soluble carbon content of 1165.58 mg C/L. Most of the originally dissolved carbon sources (58.01-66.81 %) were bio-transformed to volatile fatty acids with high bioavailability, while the further transformation to biogas was inhibited, contributing to recoverable carbon source accumulation. Overall, 21.38 % of total solid carbon sources were recovered through 8-day fermentation, the carbon extraction was implemented by solid-liquid separation with carbon loss of 14.21-22.91 %, manifesting the valid carbon recovery of 85.05-87.96 mg C/g VSS. Such CE-driven carbon recovery provided negentropy benefits in sustainable cycle economy.

Effect of zero-valent iron (ZVI) and biogas slurry reflux on methane production by anaerobic digestion of waste activated sludge.

This study aimed to improve anaerobic digestion (AD) efficiency through the addition of zero-valent iron (ZVI) and biogas slurry. This paper demonstrated that methane production was most effectively promoted at a biogas slurry reflux ratio of 60%. The introduction of ZVI into anaerobic systems does not enhance its bioavailability. However, both biogas slurry reflux and the combination of ZVI with biogas slurry reflux increase the relative abundance of microorganisms involved in the direct interspecific electron transfer (DIET) process. Among them, the dominant microorganisms Methanosaeta, Methanobacterium, Methanobrevibacter, and Methanolinea accounted for over 60% of the total methanogenic archaea. The Tax4Fun function prediction results indicate that biogas slurry reflux and the combination of ZVI with biogas slurry reflux can increase the content of key enzymes in the acetotrophic and hydrotrophic methanogenesis pathways, thereby strengthening these pathways. The corrosion of ZVI promotes hydrogen production, and the biogas slurry reflux provided additional alkaline and anaerobic microorganisms for the anaerobic system. Their synergistic effect promoted the growth of hydrotrophic methanogens and improved the activities of various enzymes in the hydrolysis and acidification phases, enhanced the system's buffer capacity, and prevented secondary environmental pollution. PRACTITIONER POINTS: Optimal methane production was achieved at a biogas slurry reflux ratio of 60%. Biogas slurry reflux in anaerobic digestion substantially reduced discharge. ZVI addition in combination with biogas slurry reflux facilitates the DIET process.

Enhanced anaerobic digestion performance and sludge filterability by membrane microaeration for anaerobic membrane bioreactor application.

Slow dissolution/hydrolysis of insoluble/macromolecular organics and poor sludge filterability restrict the application potential of anaerobic membrane bioreactor (AnMBR). Bubble-free membrane microaeration was firstly proposed to overcome these obstacles in this study. The batch anaerobic digestion tests feeding insoluble starch and soluble peptone with and without microaeration showed that microaeration led to a 65.7-144.8% increase in methane production and increased critical flux of microfiltration membrane via driving the formation of large sludge flocs and the resultant improvement of sludge settleability. The metagenomic and bioinformatic analyses showed that microaeration significantly enriched the functional genes and bacteria for polysaccharide and protein hydrolysis, microaeration showed little negative effects on the functional genes involved in anaerobic metabolisms, and substrate transfer from starch to peptone significantly affected the functional genes and microbial community. This study demonstrates the dual synergism of microaeration to enhance the dissolution/hydrolysis/acidification of insoluble/macromolecular organics and sludge filterability for AnMBR application.

The distribution and composition characteristics of siliceous rocks from Qinzhou Bay-Hangzhou Bay joint belt, South China: constraint on the tectonic evolution of plates in South China.

The Qinzhou Bay-Hangzhou Bay joint belt is a significant tectonic zone between the Yangtze and Cathaysian plates, where plentiful hydrothermal siliceous rocks are generated. Here, the authors studied the distribution of the siliceous rocks in the whole tectonic zone, which indicated that the tensional setting was facilitating the development of siliceous rocks of hydrothermal genesis. According to the geochemical characteristics, the Neopalaeozoic siliceous rocks in the north segment of the Qinzhou Bay-Hangzhou Bay joint belt denoted its limited width. In comparison, the Neopalaeozoic Qinzhou Bay-Hangzhou Bay joint belt was diverse for its ocean basin in the different segments and possibly had subduction only in the south segment. The ocean basin of the north and middle segments was limited in its width without subduction and possibly existed as a rift trough that was unable to resist the terrigenous input. In the north segment of the Qinzhou Bay-Hangzhou Bay joint belt, the strata of hydrothermal siliceous rocks in Dongxiang copper-polymetallic ore deposit exhibited alternative cycles with the marine volcanic rocks, volcanic tuff, and metal sulphide. These sedimentary systems were formed in different circumstances, whose alternative cycles indicated the release of internal energy in several cycles gradually from strong to weak.

Enhancement of phosphorus removal in a low temperature A(2)/O process by anaerobic phosphorus release of activated sludge.

An anaerobic phosphorus release tank was introduced to an anaerobic-anoxic-aerobic (A(2)/O) process treating domestic sewage to enhance the phosphorus removal at low temperature. Phosphorus release of the activated sludge from the second sedimentation tank was evaluated at 14 °C by batch cultures, and the nutrient removal in the modified low temperature A(2)/O process was further investigated at the same temperature. The results showed that the feasible sludge retention time was 14 h for sequencing batch reaction and 12 h for continuous flow operation. The ratio of raw sewage to activated sludge from the second sedimentation tank was 1:1 in volume to meet the demand of carbon resource for the growth of phosphorus release microbes. The feasible chemical oxygen demand (COD) loading rate of the activated sludge in the phosphorus release tank was 0.015-0.02 g COD/g MLSS (mixed liquor suspended solids) and the nitrate concentration should be less than 5 mg/L. The phosphorus release was doubled when the sludge was blended intermittently and gently. The anaerobic phosphorus release of the activated sludge improved the phosphate removal remarkably, as well as the removal of NH4(+)-N and total nitrogen (TN) in the modified low temperature A(2)/O process. The effluent COD, NH4(+)-N, TN and total phosphorus could meet a stricter discharge standard.