TRYBE®: an Fc-free antibody format with three monovalent targeting arms engineered for long in vivo half-life.

TrYbe® is an Fc-free therapeutic antibody format, capable of engaging up to three targets simultaneously, with long in vivo half-life conferred by albumin binding. This format is shown by small-angle X-ray scattering to be conformationally flexible with favorable 'reach' properties. We demonstrate the format's broad functionality by co-targeting of soluble and cell surface antigens. The benefit of monovalent target binding is illustrated by the lack of formation of large immune complexes when co-targeting multivalent antigens. TrYbes® are manufactured using standard mammalian cell culture and protein A affinity capture processes. TrYbes® have been formulated at high concentrations and have favorable drug-like properties, including stability, solubility, and low viscosity. The unique functionality and inherent developability of the TrYbe® makes it a promising multi-specific antibody fragment format for antibody therapy.

Alternative antibody Fab' fragment PEGylation strategies: combination of strong reducing agents, disruption of the interchain disulphide bond and disulphide engineering.

Antigen-binding fragments (Fab') of antibodies can be site specifically PEGylated at thiols using cysteine reactive PEG-maleimide conjugates. For therapeutic Fab'-PEG, conjugation with 40 kDa of PEG at a single hinge cysteine has been found to confer appropriate pharmacokinetic properties to enable infrequent dosing. Previous methods have activated the hinge cysteine using mildly reducing conditions in order to retain an intact interchain disulphide. We demonstrate that the final Fab-PEG product does not need to retain the interchain disulphide and also therefore that strongly reducing conditions can be used. This alternative approach results in PEGylation efficiencies of 88 and 94% for human and murine Fab, respectively. It also enables accurate and efficient site-specific multi-PEGylation. The use of the non-thiol reductant tris(2-carboxyethyl) phosphine combined with protein engineering enables us to demonstrate the mono-, di- and tri-PEGylation of Fab fragments with a range of PEG size. We present evidence that PEGylated and unPEGylated Fab' molecules that lack an interchain disulphide bond retain very high levels of chemical and thermal stability and normal performance in PK and efficacy models.

Towards a universal disulphide stabilised single chain Fv format: importance of interchain disulphide bond location and vL-vH orientation.

Engineered introduction of interface interchain disulphide bonds is perceived to be a simple method to increase the stability of single chain Fv (scFv). Six disulphide bond locations have been cited within the literature but the potential for the broad use of each has not been examined. Five of these disulphide bond locations were introduced into one scFv in order to compare their relative effects on expression, thermal stability, percent monomer formation and retention of antigen binding. The disulphide bond position vH44-vL100 was observed to enable the most favourable balance of biophysical properties. The vH44-vL100 disulphide bond was introduced into five additional scFv in both vL-vH and vH-vL orientations in order to investigate its general applicability. Data are presented to show the relative influence of scFv sequence, v-region organisation and interchain disulphide bond on expression yield, thermal stability and percent monomer. Introduction of the vH44-vL100 disulphide bond typically resulted in no or little increase in thermal stability and no change in percent monomer but did confer the benefit of permanently fixing monomer:dimer ratios during purification and analysis.

Engineering of Escherichia coli to improve the purification of periplasmic Fab' fragments: changing the pI of the chromosomally encoded PhoS/PstS protein.

Escherichia coli is a widely used host for the heterologous expression of proteins of therapeutic and commercial interest. The scale and speed at which it can be cultured can result in the rapid generation of large quantities of product. However, to achieve low costs of production a simple and robust purification process is also required. The general factors that impact on the cost of a purification process are the scale at which a process can be performed, the cost of the purification matrix, and the number and complexity of the chromatographic steps employed. Purification of Fab' fragments of antibodies from the periplasm of E. coli using ion exchange chromatography can result in the co-purification of E. coli host proteins having similar functional pI: such as the periplasmic phosphate binding protein, PhoS/PstS. In such circumstances, an additional chromatographic step is required to separate Fab' from PhoS. Here, we change the functional pI of the chromosomally encoded PhoS/PstS to effect its non-purification with Fab' fragments, enabling the removal of an entire chromatographic step. This exemplifies the strategy of the modification of host proteins with the aim of simplifying the production of heterologous proteins.