RESUMO
For a fixed 2 µm×2 µm area of a Co/Pt-CoO perpendicular exchange bias system we image the ferromagnetic (FM) domains for various applied fields with 10-nm resolution by magnetic force microscopy (MFM). Using quantitative MFM we measure the local areal density of pinned uncompensated spins (pinUCS) in the antiferromagnetic (AFM) CoO layer and correlate the FM domain structure with the UCS density. Larger applied fields drive the receding domains to areas of proportionally higher pinUCS aligned antiparallel to FM moments. The data confirm that the evolution of the FM domains is determined by the pinUCS in the AFM layer, and also present examples of frustration in the system.
RESUMO
We report direct force measurements of the formation of a chemical bond. The experiments were performed using a low-temperature atomic force microscope, a silicon tip, and a silicon (111) 7x7 surface. The measured site-dependent attractive short-range force, which attains a maximum value of 2.1 nanonewtons, is in good agreement with first-principles calculations of an incipient covalent bond in an analogous model system. The resolution was sufficient to distinguish differences in the interaction potential between inequivalent adatoms, demonstrating the ability of atomic force microscopy to provide quantitative, atomic-scale information on surface chemical reactivity.
RESUMO
Configuration transitions of individual molecules and atoms on surfaces are traditionally described using an Arrhenius equation with energy barrier and pre-exponential factor (attempt rate) parameters. Characteristic parameters can vary even for identical systems, and pre-exponential factors sometimes differ by orders of magnitude. Using low-temperature scanning tunnelling microscopy (STM) to measure an individual dibutyl sulfide molecule on Au(111), we show that the differences arise when the relative position of tip apex and molecule changes by a fraction of the molecule size. Altering the tip position on that scale modifies the transition's barrier and attempt rate in a highly correlated fashion, which results in a single-molecular enthalpy-entropy compensation. Conversely, appropriately positioning the STM tip allows selecting the operating point on the compensation line and modifying the transition rates. The results highlight the need to consider entropy in transition rates of single molecules, even at low temperatures.
RESUMO
We have developed an optical cantilever deflection detector with a spot size <3 µm and fm Hz(-1/2) sensitivity over a>10 MHz bandwidth. In this work, we demonstrate its potential for detecting small-amplitude oscillations of various flexural and torsional oscillation modes of cantilevers. The high deflection sensitivity of the interferometer is particularly useful for detecting cantilever oscillations in aqueous solutions, enabling us to reach the thermal noise limit in scanning or atomic force microscopy experiments with stiff cantilevers. This has resulted in atomic-resolution images of solid-liquid interfaces and submolecular-resolution images of native membranes.
RESUMO
The resonance frequency and the excitation amplitude of a silicon cantilever have been measured as a function of distance to a cleaved KBr(001) surface with a low-temperature scanning force microscope (SFM) in ultrahigh vacuum. We identify two regimes of tip-sample distances. Above a site-dependent critical tip-sample distance reproducible data with low noise and no interaction-induced energy dissipation are measured. In this regime reproducible SFM images can be recorded. At closer tip-sample distances, above two distinct atomic sites, the frequency values jump between two limiting curves on a timescale of tens of milliseconds. Furthermore, additional energy dissipation occurs wherever jumps are observed. We attribute both phenomena to rarely occurring changes in the tip apex configuration which are affected by short-range interactions with the sample. Their respective magnitudes are related to each other. A specific candidate two-level system is also proposed.
RESUMO
Atomic Force Microscopy (AFM) was used to investigate the ultrastructural appearance of transverse wood cell wall surfaces in embedded and polished Norway spruce wood blocks. The prepared surfaces showed only little height differences, suitable for high resolution AFM phase contrast imaging. Our results revealed randomly arranged wood cell wall components in the thick secondary 2 (S2) layers of the tracheid cell walls. It is concluded that the observed distribution pattern of the cellulose fibril/matrix structure is close to the original cell wall structure. In this context, the plasticity of wood cell wall components to re-arrange and adjust to different conditions resulting in diverse structural pattern is discussed.
Assuntos
Parede Celular/ultraestrutura , Microscopia de Força Atômica/métodos , Madeira/ultraestrutura , Microtomia/métodos , Modelos Biológicos , Picea/ultraestrutura , Manejo de Espécimes/métodos , Propriedades de Superfície , Inclusão do Tecido/métodosRESUMO
200-nm-thick Ni films in an epitaxial Cu/Ni/Cu/Si(001) structure are expected to have an in-plane effective magnetic anisotropy. However, the in-plane remanence is only 42%, and magnetic force microscopy domain images suggest perpendicular magnetization. Quantitative magnetic force microscopy analysis can resolve the inconsistencies and show that (i) the films have perpendicular domains capped by closure domains with magnetization canted at 51 degrees from the film normal, (ii) the magnetization in the Bloch domain walls between the perpendicular domains accounts for the low in-plane remanence, and (iii) the perpendicular magnetization process requires a short-range domain wall motion prior to wall-magnetization rotation and is nonhysteretic, whereas the in-plane magnetization requires long-range motion before domain-magnetization rotation and is hysteretic.
RESUMO
We propose and apply to the KBr(001) surface a new procedure for species recognition in scanning force microscopy (SFM) of ionic crystal surfaces which show a high symmetry of the charge arrangement. The method is based on a comparison between atomistic simulations and site-specific frequency versus distance measurements. First, by taking the difference of force-distance curves extracted at a few judiciously chosen surface sites we eliminate site-independent long-range forces. The obtained short-range force differences are then compared with calculated ones assuming plausible tip apex models. This procedure allows for the first time identification of the tip apex polarity and of the positive and negative sublattices in SFM images of the (001) cleavage surface of an ionic crystal with the rock salt structure.
RESUMO
Magnetic force microscopy (MFM) measurements were performed on an exchange-biased CoO/(CoPt) multilayer sample at 7.5 K. Applying an external magnetic field of up to 7 T saturates the ferromagnetic layer and the remaining uncompensated antiferromagnetic spins at the antiferromagnet-ferromagnet interfaces are imaged with high lateral resolution. The coupling between the uncompensated spins and the spins in the ferromagnet are found to be antiferromagnetic. Quantitative analysis of the MFM images revealed that 7% of the spins at the interface are uncompensated and contribute to the exchange biasing.