Relative Contributions of Packaging Elements to the Thermal Hysteresis of a MEMS Pressure Sensor.

Piezoresistive silicon pressure sensor samples were thermally cycled after being consecutively packaged to three different levels. These started with the absolute minimum to allow measurement of the output and with each subsequent level incorporating additional packaging elements within the build. Fitting the data to a mathematical function was necessary both to correct for any testing uncertainties within the pressure and temperature controllers, and to enable the identification and quantification of any hysteresis. Without being subjected to any previous thermal preconditioning, the sensors were characterized over three different temperature ranges and for multiple cycles, in order to determine the relative contributions of each packaging level toward thermal hysteresis. After reaching a stabilised hysteretic behaviour, 88.5% of the thermal hysteresis was determined to be related to the bond pads and wire bonds, which is likely to be due to the large thermal mismatch between the silicon and bond pad metallisation. The fluid-fill and isolation membrane contributed just 7.2% of the total hysteresis and the remaining 4.3% was related to the adhesive used for attachment of the sensing element to the housing. This novel sequential packaging evaluation methodology is independent of sensor design and is useful in identifying those packaging elements contributing the most to hysteresis.

The Role of Self-Assembled Monolayers in the Surface Modification and Interfacial Contact of Copper Fillers in Electrically Conductive Adhesives.

Printing of electrical circuits and interconnects using isotropic conductive adhesives (ICAs) is of great interest due to their low-temperature processing and compatibility with substrates for applications in sensors, healthcare, and flexible devices. As a lower cost alternative to silver (Ag), copper (Cu)-filled ICAs are desirable but limited by the formation of high-resistivity Cu surface oxides. To overcome this limitation, self-assembled monolayers (SAMs) of octadecanethiol (ODT) have been demonstrated to reduce the oxidation of micrometer-scale Cu powder particles for use in ICAs. However, the deposition and function of the SAM require further investigation, as described in this paper. As part of this work, the stages of the SAM deposition process, which included etching with hydrochloric acid to remove pre-existing oxides, were studied using X-ray photoelectron spectroscopy (XPS), which showed low levels of subsequent Cu oxidation when ODT coated. The treated Cu powders were combined with one- or two-part epoxy resins to make Cu-ICAs, and the effect of the Cu surface condition and weight loading on electrical conductivity was examined. When thermally cured in an inert argon atmosphere, ICAs filled with Cu protected by ODT achieved electrical conductivity up to 20 × 105 S·m-1, comparable to Ag-ICAs, and were used to make a functional circuit. To understand the function of the SAM in these Cu-ICAs, scanning and transmission electron microscopy were used to examine the internal micro- and nano-structures along with the elemental distribution at the interfaces within sections taken from cured samples. Sulfur (S), indicative of the ODT, was still detected at the internal polymer-metal interface after curing, and particle-to-particle contacts were also examined. XPS also identified S on the surface of cured Cu-ICAs even after thermal treatment. Based on the observations, electrical contact and conduction mechanisms for these Cu-filled ICAs are proposed and discussed.

Ultrasound assisted dispersal of a copper nanopowder for electroless copper activation.

This paper describes the ultrasound assisted dispersal of a low wt./vol.% copper nanopowder mixture and determines the optimum conditions for de-agglomeration. A commercially available powder was added to propan-2-ol and dispersed using a magnetic stirrer, a high frequency 850 kHz ultrasonic cell, a standard 40 kHz bath and a 20 kHz ultrasonic probe. The particle size of the powder was characterized using dynamic light scattering (DLS). Z-Average diameters (mean cluster size based on the intensity of scattered light) and intensity, volume and number size distributions were monitored as a function of time and energy input. Low frequency ultrasound was found to be more effective than high frequency ultrasound at de-agglomerating the powder and dispersion with a 20 kHz ultrasonic probe was found to be very effective at breaking apart large agglomerates containing weakly bound clusters of nanoparticles. In general, the breakage of nanoclusters was found to be a factor of ultrasonic intensity, the higher the intensity the greater the de-agglomeration and typically micron sized clusters were reduced to sub 100 nm particles in less than 30 min using optimum conditions. However, there came a point at which the forces generated by ultrasonic cavitation were either insufficient to overcome the cohesive bonds between smaller aggregates or at very high intensities decoupling between the tip and solution occurred. Absorption spectroscopy indicated a copper core structure with a thin oxide shell and the catalytic performance of this dispersion was demonstrated by drop coating onto substrates and subsequent electroless copper metallization. This relatively inexpensive catalytic suspension has the potential to replace precious metal based colloids used in electronics manufacturing.