Novel S-N/WO3: Optimization of photocatalytic performance of WO3 by simultaneous existence of S and N in WO3 against MB dye.

In this work, pure and S-N/WO3 (1%-7%) nanoparticles (NPs) have been developed for the degradation of MB dye. Optical properties, vibrational analysis, morphology, structural analysis, and photocatalytic activity of the samples have been evaluated using a variety of characterization techniques, including UV-vis, PL, FTIR, SEM, and x-ray diffraction (XRD). The XRD patterns showed that the stability of the orthorhombic phase of WO3 was affected by the concentrations of S and N. In SEM, nanospheres with an average size of 80 nm of NPs have been observed. The PL results showed that the e-, h+ recombination rate for the S-N7%/WO3 sample was the lowest. The degradation of MB dye has also been investigated in order to investigate the photocatalytic performance. Remarkably, S-N7%/WO3 shows the best results, with a maximum degradation of 90% in 120 min. The stability of the improved catalyst was tested using recycling and trapping studies. S-N7%/WO3 catalyst's exceptional photocatalytic activity highlights its potential use in wastewater treatment. This study will be helpful for manufacturing innovation.

Asymptomatic cytomegalovirus gastritis in an immunocompetent COVID-19 patient: A case report.

A number of complications are associated with COVID-19 due to reduced immunity. Of these, opportunistic infections are of great significance because of their atypical presentation and low detection rates. Co-infection of various parts of the gastrointestinal system with cytomegalovirus (CMV) is a common occurrence in COVID- 19 patients. Dysphagia and odynophagia are the main complaints of oesophagitis caused by CMV. Colitis due to CMV presents with melena, diarrhoea, or constipation. However, gastritis due to the same agent can be asymptomatic or associated with atypical symptoms like fever and epigastric pain. Cytomegalovirus gastritis can be fatal if not detected early. Hence, continued monitoring of routine baseline investigations is imperative until the complete resolution of COVID-19, as prompt diagnosis improves the outcomes.

Comparative photocatalytic study of visible light driven BiVO4, Cu2O, and Cu2O/BiVO4 nanocomposite for degradation of antibiotic for wastewater treatment.

Semiconductor-based photocatalysts have become increasingly used in the removal of pollutants from wastewater, especially antibiotics. A series of composite-based cuprous oxide and bismuth vanadate (Cu2O/BiVO4) composite-based photocatalysts were synthesized by using the chemical method. The structure of the Cu2O/BiVO4 composite was verified by using x-ray diffraction, scanning electron microscopy, photoluminescence, Fourier transform infrared spectroscopy, and UV-visible spectra. The degradation of methylene blue (MB) and tetracycline (TC) was investigated to check the photocatalytic activity of the Cu2O/BiVO4 composite series. The quantity of Cu2O was varied from 1% to 7% by weight to prepare the series of Cu2O/BiVO4 composites. The analysis of results verified that 5% Cu2O/BiVO4 exhibits an outstanding photocatalytic activity as compared to 1%, 3%, and 7% Cu2O/BiVO4, pure Cu2O, and pure BiVO4 under visible light irradiation. The optimum value of photocatalytic degradation achieved with 5% Cu2O/BiVO4 was 97% for MB dye and 95% for TC in 120 min, which is greater than the photocatalytic degradation of pure BiVO4 (MB 45% and TC 72%), pure Cu2O (MB 57% and TC 80%), 1% Cu2O/BiVO4 (MB 72% and TC 85%), 3% Cu2O/BiVO4 (MB 83% and TC 88%), and 7% Cu2O/BiVO4 (MB 87% and TC 91%). The stability and reusability of Cu2O/BiVO4 were also investigated. To check the major role of trapping in degradation, a trapping experiment was also performed by using three trapping agents: BQ, EDTA, and tBuOH. The results showed that Cu2O/BiVO4 exhibits an improved photocatalytic activity in the degradation of antibiotics in polluted water because the recombination rate of the electron-hole pair decreased and the surface area increased, which increased the active sites for redox reactions. Such a photocatalytic composite with high efficiency has various applications, such as energy production, environmental remediation, and water remediation.

The Western Himalayan fir tree ring record of soil moisture in Pakistan since 1855.

Data on historical soil moisture is crucial for assessing and responding to droughts that commonly occur in climate change-affected countries. The Himalayan temperate forests in Pakistan are particularly at risk of climate change. Developing nations lack the means to gather surface soil moisture (SSM) information. Tree rings are one way to bridge this gap. Here, we employed dendrochronological methods on climate-sensitive tree rings from Abies pindrow to reconstruct the SSM in the Western Himalayan mountain region of Pakistan from 1855 to 2020. December (r = 0.41), May (r = 0.40), and June (r = 0.65) SSMs were found to be the limiting factors for A. pindrow growth. However, only the June SSM showed reconstruction possibility (coefficient of efficiency = 0.201 and reduction of error = 0.325). Over the studied period, we found 6 years (wet year) when June SSM was above the threshold of 32.04 (mean + 2 δ) and 1 year (dry year) when June SSM was below the threshold of 21.28 (mean - 2 δ). It was revealed that 1921 and 1917 were the driest and wettest SSM of all time, with means of 19.34 and 36.49, respectively. Our study shows that winter soil moisture is critical for the growing season in the context of climate change. Climate change has broad impacts on tree growth in the Western Himalayas. This study will assist various stakeholders in understanding and managing local and regional climate change.

Fabrication of novel BiVO4/Bi2O3heterostructure with superior visible light induced photocatalytic properties.

Heterostructure BiVO4/Bi2O3nanocomposites with enhanced visible light activity are effectively synthesized through an easiest and single step hydrothermal route, using bismuth subnitrate and ammonium meta-vanadate as main raw materials in existence of citric acid. The phase and surface structure, topography and optical properties of synthesized composites are characterized by XRD, SEM, EDX, FTIR, UV-Visible and PL spectroscopy. It was found that 5%BiVO4/Bi2O3(BOBV-5) nanocomposite exhibit excellent photocatalytic performance for rhodamine B dye degradation and tetracyclic under irradiation of visible light as compared to single component i.e. BiVO4. The increased photocatalytic activity should be ascribed for making p-n heterojunction among p-type Bi2O3and n-type BiVO4. This p-n heterojunction successfully reduce the recombination of photogenerated charge carriers. Furthermore, the BOBV-5 novel photocatalyst shows good stability in constructive five cycles and photocatalytic activity is best for conquering photo corrosion of a photocatalysts. To explain charge migration route, whole photocatalytic mechanism was described in terms of energy band structures. Furthermore, the present work is helpful effort for design of new visible light photocatalytic materials with heterojunction structures.

A novel avian isolate of hepatitis E virus from Pakistan.

BACKGROUND: Avian hepatitis E virus (aHEV) has been associated with hepatitis-splenomegaly syndrome (HSS) in chickens along with asymptomatic subclinical infection in many cases. So far, four genotypes have been described, which cause infection in chickens, specifically in broiler breeders and layer chickens. In the present study, we isolated and identified two novel aHEV strains from the bile of layer chickens in Pakistan evincing clinical symptoms related to HSS. METHODOLOGY: Histology of liver and spleen tissues was carried out to observe histopathological changes in these tissues. Bile fluid and fecal suspensions were used for viral RNA isolation through MegNA pure and Trizol method which was further used for viral genome detection and characterization by cDNA synthesis and amplification of partial open reading frame (ORF) 1, ORF2 and complete ORF3. The bioinformatics tools; Molecular Evolutionary Genetics Analysis version 6.0 (MEGA 6), Mfold and ProtScale were used for phylogenic analysis, RNA secondary structure prediction and protein hydropathy analysis, respectively. RESULTS: Sequencing and phylogenetic analysis on the basis of partial methyltranferase (MeT), helicase (Hel) domain, ORF2 and complete ORF3 sequence suggests these Pakistani aHEV (Pak aHEV) isolates may belong to a Pakistani specific clade. The overall sequence similarity between the Pak aHEV sequences was 98-100%. The ORF1/ORF3 intergenic region contains a conserved cis-reactive element (CRE) and stem-loop structure (SLS). Analysis of the amino acid sequence of ORF3 indicated two hydrophobic domains (HD) and single conserved proline-rich domain (PRD) PREPSAPP (PXXPXXPP) with a single PSAP motif found in C-terminal. Amino acid changes S15 T, A31T, Q35H and G46D unique to the Pak aHEV sequences were found in the N-terminal region of ORF3. CONCLUSIONS: Our data suggests that Pak aHEV isolates may represent a novel Pakistani clade and high sequence homology to each other support the supposition they may belong to a monophyletic clade circulating in the region around Pakistan. The data presented in this study provide further information for aHEV genetic diversity, genotype mapping, global distribution and epidemiology.

Facile synthesis and antimicrobial activity of CdS-Ag2S nanocomposites.

In this study CdS-Ag2S nanocomposites for antibacterial activity were synthesized via facile co-precipitation method using PVP as capping agent. The prepared nanocomposites have particle sizes in the range of 50-100 nm (SEM) and PVP addition has good influence on the morphology of nanocomposites. The antimicrobial activity of pure Ag2S, CdS and CdS-Ag2S composites was evaluated against Pseudomonas aeruginosa, Staphylococcus aureus and Escherichia coli. The results demonstrate that antibacterial activity was significantly improved due to increasing ratio of CdS into CdS-Ag2S nanocomposites in comparison to pure Ag2S and CdS.

Efficient biosensing through 1D silver nanostructured devices using plasmonic effect.

The current work explores the excitation of surface plasmon polaritons (SPPs) on a one dimensional (1D) silver nano-grating device, simulated on glass substrate, which can sense a very small change in the refractive index of an analyte adjacent to it. The most recent modeling technique finite element analysis is applied in this work by using a COMSOL RF module. The models of 1D grating devices of different slit widths with fixed periodicity and film thickness are simulated. The data is collected and then used to study higher refractive index unit per nanometer (RIU/nm) as well as the effect of the widths of the slits on the RIU. A number of investigations are done by the simulated data, like a dip in the transmission spectra of p-polarized light. This dip is due to SPP resonance with the variation of slit width. Furthermore, the most fascinating part of the research is the COMSOL modeling that provides an opportunity to look into factors affecting higher RIU/nm, while visualizing the cross-sectional view of the grating device and strong electric field enhancement at the surface of the metallic device. When the slit width is almost equal to half of the periodicity of the grating device, SPP resonance increases and it is at maximum for the slit width equal to two-thirds of the periodicity, because the coupling efficiency is at maximum.

Membrane biofouling behaviors at cold temperatures in pilot-scale hollow fiber membrane bioreactors with quorum quenching.

In this study, the seasonality of the biofouling behavior of pilot-scale membrane bioreactors (MBRs) run in parallel with vacant sheets and quorum quenching (QQ) sheets using real municipal wastewater was investigated. QQ media delayed fouling, but low temperatures caused severe biofouling. The greater amount of extracellular polymeric substances (EPSs) produced in cold weather was responsible for the faster biofouling of a membrane, even with QQ media. There were significant negative relationships between EPS levels and water temperature. Cold weather was detrimental to the degradation of quorum sensing signal molecules by QQ sheets, whose activity was restored with a higher dose of QQ bacteria. The QQ bacteria in the sheets experienced a slight loss in activity during the early stage of the field test, but survived in the pilot-scale MBR fed with real wastewater. There were no significant discrepancies in treatment efficiency among conventional, vacant, and QQ MBRs.

Isolation of anticancer and antimicrobial metabolites from Epicoccum nigrum; endophyte of Ferula sumbul.

Owing to the importance of endophytes, current research was aimed to purify the secondary metabolites from targeted source. Ferula sumbul, a lipophilic extract of the endophyte was prepared in 10% methanol and partitioned with ethyl acetate and bioassay guided isolation was carried using standard protocols against bacterial, fungal and cancer cells. The active fractions consisted of three new metabolites (2-methyl-3-nonyl prodiginine, Bis (2-ethylhexyl) phthalate, and a meroterpenoid, Preaustinoid A). Their structures were confirmed with LCMS/MS. The purified metabolites showed valuable results against tested activities which concluded that these compounds have great potential and these may be applicable to textile (dyeing), pharmaceutical (drug, infectious agents) and food (preservatives) industries. This study reveals the potential of E. nigrum as an important source of bioactive compounds including 2-methyl-3-nonyl prodiginine, Bis (2-ethylhexyl) phthalate, and Preaustinoid A. This is first report of isolation of prodiginines as well as meroterpenoid and Bis (2-ethylhexyl) phthalate from Epicoccum nigrum.

FLUOROSCOPY TIME DURING CARDIAC CATHETERIZATION PROCEDURES USING THE RADIAL AND FEMORAL ROUTES.

BACKGROUND: Use of trans-radial route for cardiac catheterization is on the rise but is associated with increased radiation exposure to the operator. Our aim was to compare the radiation exposure, by taking fluoroscopy time (FT) as a surrogate of radiation exposure, to the operator with femoral and radial routes. METHODS: This prospective observational study was carried out at Army Cardiac Center Lahore from lst Jan to 1st June 2013. Mean fluoroscopy times via trans-radia (TR) and trans-femoral (TF) routes were compared. Procedure time was considered as time from sheath insertion to the finish of the diagnostic and interventional procedure. Descriptive statistics were used to explain the data. Chi square test was applied to compare qualitative variables between them. RESULTS: A total of 1,110 diagnostic & PCI cases were performed out of which there were 850 diagnostic CA and 260 PCI cases. The mean procedure time & mean fluoroscopy time for TF-CA was 15.5±5.5 minutes and 4.3±3.2 minutes respectively in the current study while for TR-CA was 6.6±4.1. For TF-PCI, mean procedure time was 42.3±16.7 minutes, mean fluoroscopy time was 11.6±7.7 minutes & for TR-PCI it was 55.3±19.2 and 15.4±12.1. CONCLUSION: Radial route for cardiac catheterization procedures is associated with longer fluoroscopy time leading to increased radiation exposure to the operator along with an increased use of contrast.

Adsorption behavior of different cresols on bismuthene: a DFT study.

Phenolic compounds present in wastewater were utilized for first-principle calculations based on DFT to observe adsorption effects. Results indicate that bismuthene exhibits different adsorption characteristics for different compounds. Following the adsorption process, the aromatic ring remains in the same plane, while CH3 and OH groups move upward, causing slight changes in the molecules' overall position. The calculated results show that bisphenol A has the least atomic distance (4.00 Å) from the bismuthene surface and the highest adsorption energy value (12.8509 eV), indicating the stability and smoothness of the adsorption process. The electronic properties results reveal that phenolic compounds exhibit overlapping peaks at a distance from the Fermi level, describing the stability of the adsorption system. Additionally, the charge transfer results mirror the adsorption energy calculation results, showing that the bisphenol A adsorption system accepts a greater amount of (-0.116e) charge from the bismuthene surface, demonstrating a strong adsorption effect.

Facile green synthesis of novel tantalum doped tungsten trioxide for photocatalytic degradation: Correlation with COMSOL simulation.

The facilegreen synthesis techniqueis becoming more and more important, and it has been proposed as a potential substitute for chemical techniques. The current study describes a low-cost, environmentally friendly method for producing tungsten trioxide (WO3) and tantalum (Ta) doped WO3nanoparticles that uses 15 % (w/v) Azadirachta indica (Neem) leaf extract and different concentrations of Ta dopant (1 to 5 %) due to its well-matched ionic radius with WO3. Various techniques FESEM, TEM, EDX, BET, UV-Vis and PL, XRD, and FTIR were used to illustrate the morphological, elemental, optical, structural, and vibrational analysis of the synthesized nanoparticles respectively. Interestingly, the band gap was significantly reduced to 1.88 eV by the addition of a dopant element. For 3 % Ta/WO3, the average particle size was also reduced to 31.6 nm. The synthesized WO3nanoparticles employed in the current study have been used for photocatalytic activitypurposes. Methylene blue (MB), one of the principal water pollutants, was degraded more quickly by the synthesized Ta/WO3nanoparticles when exposed to UV radiation. Among them, 3 % Ta/WO3 gives significantly higher photodegradation 89 % attributed to the Burstein-Moss effect. The significant output of optimized nano-photocatalyst has been observed from the trapping experiment and reusability test. Furthermore, Zeta potential and TOC analysis have been taken to check the stability and mineralization performance. Additionally, the results of the simulation that was carried out using the finite element analysis approach in the RF module of COMSOL Multiphysics 5.3a are quite similar to the experimental findings. This simulation method made it easier for readers to understand the numerous aspects of the photocatalytic process that has been discussed here.

Benefits of fungal-to-bacterial quorum quenching as anti-biofouling strategy in membrane bioreactors for wastewater treatment and water reuse.

This study addresses membrane biofouling in membrane bioreactors (MBRs) by exploring fungal-to-bacterial quorum quenching (QQ) strategies. While most research has been focused on bacterial-to-bacterial QQ tactics, this study identified fungal strain Vanrija sp. MS1, which is capable of degrading N-acyl-homoserine lactones (signaling molecules of Gram-negative bacteria). To determine the benefits of fungal over bacterial strains, after immobilization on fluidizing spherical beads in an MBR, MS1 significantly reduced the fouling rate by 1.8-fold compared to control MBR, decreased extracellular polymeric substance levels in the biofilm during MBR operation, and favorably changed microbial community and bacterial network, resulting in biofouling mitigation. It is noteworthy that, unlike Rhodococcus sp. BH4, MS1 enhanced QQ activity when switching from neutral to acidic conditions. These results suggest that MS1 has the potential for the effective treatment of acidic industrial wastewater sources such as semiconductor and secondary battery wastewater using MBRs.

Exploring the sensing potential of Fe-decorated h-BN toward harmful gases: a DFT study.

Gas sensing technology has a broad impact on society, ranging from environmental and industrial safety to healthcare and everyday applications, contributing to a safer, healthier, and more sustainable world. We studied pure and Fe-decorated hexagonal boron nitride (h-BN) gas sensor for monitoring of carbon-based gases using density functional theory (DFT). The calculations utilized the Generalized Gradient Approximation with the Perdew-Burke-Ernzerhof (GGA-PBE) exchange-correlation functional. The novelty of our study lies in the investigation of the adsorption of harmful gases such as carbonyl sulfide, carbinol, carbimide, and carbonyl fluoride on both pure and Fe-decorated h-BN. The deviation in structural, electronic, and adsorption properties of h-BN due to Fe decoration has been studied along with the sensing ability to design said material towards carbon monoxide (CO), carbon dioxide (CO2), carbonyl sulfide (COS), carbinol, (CH4O), carbimide (CH2N2), and carbonyl fluoride (CF2O) gases. Gases such as CO, COS, CH2N2, and CF2O exhibited chemisorption, while CO2, and CH4O exhibited physisorption behavior. The introduction of Fe altered the semiconductor properties of h-BN and rendered it metallic. Enhanced electronic properties were observed due to a robust hybridization occurring between the d-orbitals of Fe-decorated BN and the gas molecules. The extended recovery periods observed for gases, aside from CO2, indicate their adhesive interactions with Fe-decorated h-BN. The reduction in desorption duration as temperature rises allows Fe-decorated h-BN to function as a reversible gas sensor. This research opens up a novel pathway for the synthesis and advancement of cost-effective, environmentally friendly double-atom catalysts with high sensitivity for capturing and detecting molecules such as CO, COS, CH2N2, CO2, CH4O, and CF2O.

Anesthesia management of living donor liver transplantation in a patient with scimitar syndrome.

Scimitar syndrome is a rare congenital anomaly with a hallmark of an abnormal drainage of pulmonary veins into inferior vena cava instead of the left atrium; this creates a curvilinear radiological pattern resembling a sword (scimitar) on a chest radiograph, thus attracting the name. This case report highlights the challenges during liver transplantation, and perioperative anesthetic management of a patient with an uncorrected Scimitar Syndrome.

Phytotoxic responses of wheat to an imidazolium based ionic liquid in absence and presence of biochar.

Research on ionic liquids (ILs) and biochars (BCs) is a novel site of scientific interest. An experiment was designed to assess the effect of 1-propanenitrile imidazolium trifluoro methane sulfonate ([C2NIM][CF3SO3]) ionic liquid (IL) and IL-BC combination on the wheat plant. Three working standards of the IL; 50, 250, 500 and 1000 mg/L, prepared in deionized water, were tested in the absence and presence of BC on wheat seedling. Results indicated significant decrease in seed germination (%), length, fresh weight, chlorophyll a, b and carotenoid contents of wheat seedlings at 250, 500 and 1000 mg/L of the IL. An admirable increase in phenolic and 2,2-diphenyl-1-picrylhydrazyl (DPPH) contents of wheat seedlings was noted at 250, 500 and 1000 mg/L of the IL. The application of BC significantly ameliorated the negative effects of IL on the selected parameters of wheat. It is inferred that the undesirable effects of the IL on wheat growth can be positively restored by addition of BC.

Does quorum quenching matter to microbial community dynamics in long-term membrane bioreactor operation?

Quorum quenching (QQ) has effectively prevented biofouling in membrane bioreactors (MBRs) employing isolated QQ bacterial strains. However, the influence of QQ on the microbial population still needs to be fully understood. This research aims to analyze the microbial population in MBRs over an extended period (>250 days) under different conditions, such as varying aeration intensities and doses of QQ bacteria, QQ media, and types of feed. Results show that no significant changes occurred in the structure and diversity of the microbial community in the mixed liquor and biofilm due to QQ treatment. Canonical correspondence analysis did reveal that the microbial communities were strongly influenced by feed types and phases. The microbial community composition varied between bacterial habitats (i.e., mixed liquor and biofilm), showing the two dominant phyla Proteobacteria and Bacteroidota in the former and Proteobacteria and Chloroflexi in the latter. The co-occurrence network analysis indicated that the biofilm (with 163 edges) in the MBR fed with real wastewater exhibited a more intricate network than the biofilm (with 53 edges) in the MBR fed with synthetic wastewater. With QQ, the biofilm exhibited more positive edges than negative ones. The phylogenetic investigation of communities showed that QQ barely affects functional gene-related quorum sensing (e.g., bacterial chemotaxis, motility proteins, and secretion) in mixed liquor but in biofilms at relatively large QQ doses (> 75 mg/L BH4). This research sheds light on the bacterial QQ's role in reducing MBR biofouling and provides crucial insights into its underlying mechanisms.

Facile hydrothermal synthesis of BiVO4 nanomaterials for degradation of industrial waste.

Bismuth Vanadate (BiVO4) has been synthesized using simple hydrothermal technique while varying the pH of concentrated H2SO4. With the increase of pH values (from 06 to 10), the morphology of the synthesized material tuned in the form of nano-spheres and cubes in the range from 50 to 60 nm. The lateral affect tuned the bandgap of BiVO4 from 2.47 eV to 2.50 eV which is significant in the context of present study. It is worth mentioning that desirous bandgap corresponds to the visible spectrum of the solar light being abundantly available and finds many applications in real life. The synthesized nanomaterial BiVO4 has been characterized through UV-Vis spectroscopy, X-ray diffraction, Scanning electron microscope and energy-dispersive X-ray (EDX) spectroscopy. The synthesized BiVO4 has been tested as photocatalyst for degradation of industrial pollutant from Leather Field Industry. Said catalyst (BiVO4) successfully degraded the industrial pollutant after 3 h under solar light irradiation. Therefore, the BiVO4 can be regarded as potential photocatalyst for degradation of industrial waste which is highly needed.

Development of a hybrid mixed-mode solar dryer for product drying.

Sun drying in the open air is quite popular worldwide. However, the use of solar dryers to preserve various perishable agricultural products is a relatively new area of study, and the long-term effects of this method are not yet fully understood. The slow drying process in direct sunlight can contaminate the dried materials by soil and insects. To overcome these challenges, we devised a sun drying system that included a heating part, a drying area, a portable stand, fans, and a 50-W photovoltaic panel. An alternate energy source was used to power the drying process during cloudy days and at night. Fresh Freestone peach, Golden apple, and Anaheim chilies weighing 10 kg each with the initial moisture content of 89%, 87%, and 75% on a wet basis (w.b), respectively, were used in the experiments. The final moisture content of the samples was reduced by an average of 16%, 15%, and 11% for Freestone peaches, Golden apples, and Anaheim chilies, respectively. The quality analysis was carried out to determine sample composition, total bacteria, and color of dried products. The results indicated that the dried products met the recommended quality standards for food products in terms of composition, total bacteria, and color. This research supports the use of a hybrid mixed-mode solar dryer for drying a wide range of perishable agricultural products.