Gain investigation of Perylene-Red-doped PMMA for stimulated luminescent solar concentrators.

Luminescent solar concentrators (LSCs) utilizing stimulated emission by a seed laser are a promising approach to overcome the limitations of conventional LSCs, with a significant reduction of the photovoltaic material. In our previous work, we demonstrated the principle of a stimulated LSC (s-LSC) and correspondingly developed a model for quantifying the output power of such a system, taking into account different important physical parameters. The model suggested Perylene Red (PR) dye as a potential candidate for s-LSCs. Here, we experimentally investigate the gain of PR-doped polymethyl methacrylate (PMMA) required for s-LSCs using a single pump wavelength (instead of the solar spectrum) as a proof of principle. The results found from the experiment are well matched with the previously developed numerical model except for gain saturation, which occurs at a comparatively small seed laser signal power. To investigate the gain saturation, two approaches were taken: investigating (i) spectral hole burning and (ii) triplet state absorption. Experimental investigation of spectral hole burning with PR dyes showed a small effect on the gain saturation. We developed a general state model considering triplet state absorption of the PR dyes for the second approach. The state model suggests that the PR dyes suffer from significant triplet state absorption loss, which obstructs the normal operation of the PR-based s-LSC system.

Modeling of stimulated emission based luminescent solar concentrators.

The efficiency improvement of luminescent solar concentrators (LSCs) necessary for practical realization is currently hindered by one major loss mechanism: reabsorption of emitted photons by the luminophores. Recently, we explored a promising technique for reducing reabsorption and also improving directional emission in LSCs utilizing stimulated emission, rather than only spontaneous emission, with an inexpensive seed laser. In this work, a model is developed to quantify the gain (i.e. the amount of amplification of a low power seed laser propagating through the solar-pumped concentrator) of stimulated-LSCs (s-LSCs) considering the effects of different important physical parameters. The net optical output power, available for a small PV cell, from the concentrator can also be determined from the model, which indicates the performance of s-LSCs. Finally, the performance of different existing material systems is investigated using literature values of the parameters required for the model, and a set of optimal parameters is suggested for practical realization of such a device.

Luminescent solar concentrators utilizing stimulated emission.

Luminescent solar concentrators (LSCs) are an emerging technology that aims primarily to reduce the cost of solar energy, with great potential for building integrated photovoltaic (PV) structures. However, realizing LSCs with commercially viable efficiency is currently hindered by reabsorption losses. Here, we introduce an approach to reducing reabsorption as well as improving directional emission in LSCs by using stimulated emission. Light from a seed laser (potentially an inexpensive laser diode) passes through the entire area of the LSC panel, modifying the emission spectrum of excited dye molecules such that it is spectrally narrower, at wavelengths that minimize reabsorption to allow net gain in the system, and directed towards a small PV cell. A mathematical model, taking into account thermodynamic considerations, of such a system is presented which identifies key parameters and allows evaluation in terms of net effective output power.

Optical gain characterization of Perylene Red-doped PMMA for different pump configurations.

The optical gain is measured in Perylene Red (PR)-doped polymethyl methacrylate (PMMA) slabs for copropagating and transverse pumping configurations based on a single-pass pump-probe method where a small signal is used as a probe beam. The gain is characterized in terms of the stimulated gain coefficient (g(S)) for both pump configurations. This material property determines the strength of pump absorption and coupling to the probe signal beam through stimulated emission. For copropagating pumping, g(S) was found to be (3.05±0.17)×10(-3) m/W for ∼0.05 mM PR-doped PMMA using a 633 nm probe laser, pumping with a 532 nm CW laser. For transverse pumping, g(S) was found to be (3.28±0.09)×10(-3) m/W for a ∼0.15 mM sample. The small difference in the gain coefficient is attributed to the difference in concentration. The stimulated gain coefficient, a material property of the gain medium independent of the pump configuration and experimental setup, offers a useful and convenient way to characterize the optical gain for solid-state lasers or amplifiers.

Dual quantum cascade lasers for noninvasive glucose detection using photoacoustic spectroscopy.

The combination of mid-infrared and photoacoustic spectroscopy has shown promising developments as a substitute for invasive glucose detection technology. A dual single-wavelength quantum cascade laser system has been developed using photoacoustic spectroscopy for noninvasive glucose monitoring. Biomedical skin phantoms with similar properties to human skin have been prepared with blood components at different glucose concentrations as test models for the setup. The detection sensitivity of the system has been improved to ± 12.5 mg/dL in the hyperglycemia blood glucose ranges. An ensemble machine learning classifier has been developed to predict the glucose level in the presence of blood components. The model, which was trained with 72,360 unprocessed datasets, achieved a 96.7% prediction accuracy with 100% of the predicted data located in zones A and B of Clarke's error grid analysis. These findings fulfill both the US Food and Drug Administration and Health Canada requirements for glucose monitors.

Progress and Perspectives of Mid-Infrared Photoacoustic Spectroscopy for Non-Invasive Glucose Detection.

The prevalence of diabetes is rapidly increasing worldwide and can lead to a range of severe health complications that have the potential to be life-threatening. Patients need to monitor and control blood glucose levels as it has no cure. The development of non-invasive techniques for the measurement of blood glucose based on photoacoustic spectroscopy (PAS) has advanced tremendously in the last couple of years. Among them, PAS in the mid-infrared (MIR) region shows great promise as it shows the distinct fingerprint region for glucose. However, two problems are generally encountered when it is applied to monitor real samples for in vivo measurements in this MIR spectral range: (i) low penetration depth of MIR light into the human skin, and (ii) the effect of other interfering components in blood, which affects the selectivity of the detection system. This review paper systematically describes the basics of PAS in the MIR region, along with recent developments, technical challenges, and data analysis strategies, and proposes improvements for the detection sensitivity of glucose concentration in human bodies. It also highlights the recent trends of incorporating machine learning (ML) to enhance the detection sensitivity of the overall system. With further optimization of the experimental setup and incorporation of ML, this PAS in the MIR spectral region could be a viable solution for the non-invasive measurement of blood glucose in the near future.

A Critical Review on the Sensing, Control, and Manipulation of Single Molecules on Optofluidic Devices.

Single-molecule techniques have shifted the paradigm of biological measurements from ensemble measurements to probing individual molecules and propelled a rapid revolution in related fields. Compared to ensemble measurements of biomolecules, single-molecule techniques provide a breadth of information with a high spatial and temporal resolution at the molecular level. Usually, optical and electrical methods are two commonly employed methods for probing single molecules, and some platforms even offer the integration of these two methods such as optofluidics. The recent spark in technological advancement and the tremendous leap in fabrication techniques, microfluidics, and integrated optofluidics are paving the way toward low cost, chip-scale, portable, and point-of-care diagnostic and single-molecule analysis tools. This review provides the fundamentals and overview of commonly employed single-molecule methods including optical methods, electrical methods, force-based methods, combinatorial integrated methods, etc. In most single-molecule experiments, the ability to manipulate and exercise precise control over individual molecules plays a vital role, which sometimes defines the capabilities and limits of the operation. This review discusses different manipulation techniques including sorting and trapping individual particles. An insight into the control of single molecules is provided that mainly discusses the recent development of electrical control over single molecules. Overall, this review is designed to provide the fundamentals and recent advancements in different single-molecule techniques and their applications, with a special focus on the detection, manipulation, and control of single molecules on chip-scale devices.