Limited effect of anatomical insert geometry on in vitro laxity in balanced anatomic posterior cruciate ligament retaining total knee arthroplasty.

PURPOSE: The present study assessed the effect of insert articular surface geometry (anatomical versus conventional insert design) on anteroposterior (AP) translation and varus-valgus (VV) laxity in balanced posterior cruciate ligament (PCL) retaining total knee arthroplasty (TKA). Secondly, we evaluated if the AP translation and VV laxity in the reconstructed knee resembled the stability of the native knee. METHODS: Nine fresh-frozen full-leg cadaver specimens were used in this study. After testing the native knee, anatomical components of a PCL-retaining implant were implanted. The knee joints were subjected to anteriorly and posteriorly directed forces (at 20° and 90° flexion) and varus-valgus stresses (at 20°, 45° and 90° flexion) in both non-weightbearing and weightbearing situations in a knee kinematics simulator. Measurements were performed in the native knee, TKA with anatomical insert geometry (3° built-in varus, medial concave, lateral convex), and TKA with symmetrical insert geometry. RESULTS: In weightbearing conditions, anterior translations ranged between 2.6 and 3.9 mm at 20° flexion and were < 1 mm at 90° flexion. Posterior translation at 20° flexion was 2.7 mm for the native knee versus 4.0 mm (p = 0.047) and 7.0 mm (p = 0.02) for the symmetrical insert and the anatomical insert, respectively. Posterior translation at 90° flexion was < 1.1 mm and not significantly different between the native knee and insert types. In non-weightbearing conditions, the anterior translation at 20° flexion was 5.9 mm for the symmetrical and 4.6 mm for the anatomical insert (n.s.), compared with 3.0 mm for the native knee (p = 0.02). The anterior translation at 90° flexion was significantly higher for the reconstructed knees (anatomical insert 7.0 mm; symmetrical insert 9.2 mm), compared with 1.6 mm for the native knee (both p = 0.02). Varus-valgus laxity at different flexion angles was independent of insert geometry. A valgus force in weightbearing conditions led to significantly more medial laxity (1°-3° opening) in the native knee at 45° and 90° flexion compared with the reconstructed knee for all flexion angles. CONCLUSIONS: Insert geometry seems to have a limited effect with respect to AP translation and VV laxity, in the well-balanced PCL-retaining TKA with an anatomical femoral component. Secondly, AP translation and VV laxity in the reconstructed knee approximated the laxity of the native knee.

Bicompartmental, medial and patellofemoral knee replacement might be able to maintain unloaded knee kinematics.

INTRODUCTION: Unicompartmental knee arthroplasty (UKA) and total knee arthroplasty (TKA) are standard procedures for treating knee joint arthritis. Neither UKA nor TKA seems to be optimally suited for patients with bicompartmental osteoarthritis that affects only the medial and patellofemoral compartments. A bicompartmental knee arthroplasty (BKA) was designed for this patient group. This study aimed to compare the effectiveness of a BKA and TKA in restoring the kinematics of the knee joint. MATERIALS AND METHODS: In this in vitro study, three types of knee arthroplasties (BKA, posterior cruciate ligament-retaining, and posterior cruciate ligament-resecting TKA) were biomechanically tested in six freshly frozen human cadaveric specimens. Complete three-dimensional kinematics was analyzed for each knee arthroplasty during both passive and loaded conditions in a validated knee kinematics rig. Infrared motion capture cameras and retroreflective markers were used for recording data. RESULTS: No significant differences could be found between the three types of arthroplasties. However, similar kinematic changes between BKA and a native knee joint were documented under passive conditions. However, in a weight-bearing mode, a significant decrease in femoral rotation during the range of motion was found in arthroplasties compared to the native knee, probably caused by contraction of the quadriceps femoris muscle, which leads to a decrease in the anterior translation of the tibia. CONCLUSIONS: Kinematics similar to that of the natural knee can be achieved by BKA under passive conditions. However, no functional advantage of BKA over TKA was detected, which suggests that natural knee kinematics cannot be fully imitated by an arthroplasty yet. Further prospective studies are required to determine the anatomic and design factors that might affect the physiologic kinematics.

Internal femoral component malrotation in TKA significantly alters tibiofemoral kinematics.

PURPOSE: Femoral component malrotation in total knee arthroplasty (TKA) is clinically proven to cause dissatisfaction and impaired function. This study is an attempt to characterize the tibiofemoral kinematics following femoral malrotation in posterior stabilized (PS) TKA. It was hypothesized that internal malrotation would introduce the most pronounced changes. METHODS: Six fresh-frozen cadaver specimens were mounted in a kinematic rig. Three motion patterns were applied with the native knee and following PS TKA (passive motion, open chain extension, and squatting) while infrared cameras recorded the trajectories of markers attached to femur and tibia. Three different femoral implants were tested: a conventional posterior stabilized component, and adapted components of the same implant with 5° of intrinsic external and internal rotation, respectively. RESULTS: The implantation of the PS TKA resulted in less tibial internal rotation (squat 33-70°, p < 0.05) and the medial femoral condyle shifted posteriorly especially in deep flexion (squat 84-111°, p < 0.05). Internal component malrotation caused internal rotation and abduction of the tibia in flexion (squat 33-111°, p < 0.05), an elevated (squat 43-111°, p < 0.05) and more anterior (passive 61-126°, p < 0.05) located medial femoral condyle and a lateral femoral condyle located more posterior and inferior (squat 73-111°, p < 0.05) than in the neutrally aligned TKA. External component malrotation caused only little changes under passive motion. Under a squat there was less internal rotation and more adduction to the tibia (33-111°, p < 0.05). The medial femoral condyle was moved more posterior (squat 59-97°, p < 0.05), the lateral femoral condyle more superior (squat 54-105°, p < 0.05) than in the neutrally aligned TKA. CONCLUSION: The greatest differences to the native tibiofemoral kinematics were introduced by internal rotation of the femoral component. Also neutrally and externally rotated femoral components introduce kinematic changes, but to a lesser extent. With respect to the alterations introduced to kinematics internal malrotation should be avoided when performing PS TKA.

Articulation of Native Cartilage Against Different Femoral Component Materials. Oxidized Zirconium Damages Cartilage Less Than Cobalt-Chrome.

BACKGROUND: Oxidized zirconium (OxZr) is produced by thermally driven oxidization creating an oxidized surface with the properties of a ceramic at the top of the Zr metal substrate. OxZr is much harder and has a lower coefficient of friction than cobalt-chrome (CoCr), both leading to better wear characteristics. We evaluated and compared damage to the cartilage of porcine patella plugs, articulating against OxZr vs CoCr. Our hypothesis was that, owing to its better wear properties, OxZr would damage cartilage less than CoCr. If this is true, OxZr might be a better material for the femoral component during total knee arthroplasty if the patella is not resurfaced. METHODS: Twenty-one plugs from porcine patellae were prepared and tested in a reciprocating pin-on-disk machine while lubricated with bovine serum and under a constant load. Three different configurations were tested: cartilage-cartilage as the control group, cartilage-OxZr, and cartilage-CoCr. Macroscopic appearance, cartilage thickness, and the modified Mankin score were evaluated after 400,000 wear cycles. RESULTS: The control group showed statistically significant less damage than plugs articulating against both other materials. Cartilage plugs articulating against OxZr were statistically significantly less damaged than those articulating against CoCr. CONCLUSION: Although replacing cartilage by an implant always leads to deterioration of the cartilage counterface, OxZr results in less damage than CoCr. The use of OxZr might thus be preferable to CoCr in case of total knee arthroplasty without patella resurfacing.

Knee kinetics and kinematics: What are the effects of TKA malconfigurations?

PURPOSE: Total knee arthroplasty (TKA) is a very successful surgical procedure. However, implant failures and patient dissatisfaction still persist. Sometimes surgeons are not able to understand and explain these negative performances because the patient's medical images "look good", but the patient "feels bad". Apart from radiograph imaging and clinical outcome scores, conventionally used follow-up methods are mainly based on the analysis of knee kinematics. However, even if kinematics remains close to the "normal" range of motion, the patient may still complain about pain and functional limitations. To provide more insight into this paradox, a better quantitative understanding of TKA mechanics must be developed. For this purpose, improved techniques for clinical follow-up, combining kinetics and kinematics analysis, should be introduced to help surgeons to assess and understand TKA performance. METHODS: An analysis on four TKA designs was performed, and the changes in kinematics and in kinetics induced by several implant configurations (simulating implant malalignment and different knee anatomy) were compared. More specifically, analysed tibio-femoral and patello-femoral contact forces and tibio-femoral kinematics were analysed during a squat task up to 120°. RESULTS: The results from this study show that contact forces (with changes up to 67 %) are more heavily affected by malconfigurations than kinematics, for which maximum deviations are of the order of 5 mm or 5°, similar to the simulated surgical errors. The results present a similar trend for the different designs. CONCLUSIONS: The results confirm the hypothesis that kinematics is not the only and also not the most relevant parameter to predict or explain knee function after TKA. In the future, techniques to analyse knee kinetics should be integrated in the clinical follow-up.

Isolated patellofemoral arthroplasty reproduces natural patellofemoral joint kinematics when the patella is resurfaced.

PURPOSE: The objectives of this in vitro project were to compare the dynamic three-dimensional patellofemoral kinematics, contact forces, contact areas and contact pressures of a contemporary patellofemoral prosthetic implant with those of the native knee and to measure the influence of patellar resurfacing and patellar thickness. The hypothesis was that these designs are capable to reproduce the natural kinematics but result in higher contact pressures. METHODS: Six fresh-frozen specimens were tested on a custom-made mechanical knee rig before and after prosthetic trochlear resurfacing, without and with patellar resurfacing in three different patellar thicknesses. Full three-dimensional kinematics were analysed during three different motor tasks, using infrared motion capture cameras and retroflective markers. Patellar contact characteristics were registered using a pressure measuring device. RESULTS: The patellofemoral kinematic behaviour of the patellofemoral arthroplasty was similar to that of the normal knee when the patella was resurfaced, showing only significant (p < 0.0001) changes in patellar flexion. Without patellar resurfacing, significant more patellar flexion, lateral tilt and lateral rotation was noticed. Compared to the normal knee, contact pressures were significantly elevated after isolated trochlear resurfacing. However, the values were more than doubled after patellar resurfacing. Changes in patellar thickness only influenced the antero-posterior patellar position. There was no other influence on the kinematics, and only a limited influence on the contact pressures in the low flexion angles. CONCLUSION: The investigated design reproduced the normal patellofemoral kinematics acceptable well when the patella was resurfaced. From a kinematic point of view, patellar resurfacing may be advisable. However, the substantially elevated patellar contact pressures remain a point of concern in the decision whether or not to resurface the patella. This study therefore not only adds a new point in the discussion whether or not to resurface the patella, but also supports the claimed advantage that a patellofemoral arthroplasty is capable to reproduce the natural knee kinematics.

All-polyethylene tibial components generate higher stress and micromotions than metal-backed tibial components in total knee arthroplasty.

PURPOSE: Most total knee arthroplasty tibial components are metal-backed, but an alternative tibial component made entirely of polyethylene (all-polyethylene design) exists. While several clinical studies have shown that all-poly design performs similarly to the metal-backed, the objective of this study is to perform a biomechanical comparison. METHODS: Loads, constraints and geometries during a squat activity at 120° of flexion were obtained from a validated musculoskeletal model and applied to a finite element model. Stresses in the tibia and micromotions at the bone-implant interface were evaluated for several implant configurations: (1) three different thicknesses of the cement penetration under the baseplate (2, 3 and 4 mm), (2) the presence or absence of a cement layer around the stem of the tibial tray and (3) three different bone conditions (physiological, osteopenic and osteoporotic bone). RESULTS: All-polyethylene tibial components resulted in significantly higher (p < 0.001) and more uneven stress distributions in the cancellous bone under the baseplate (peak difference: +128.4 %) and fivefold increased micromotions (p < 0.001). Performance of both implant designs worsened with poorer bone quality with peaks in stress and micromotion variations of +40.8 and +54.0 %, respectively (p < 0.001). Performance improvements when the stem was cemented were not statistically significant (n.s.). CONCLUSION: The metal-backed design showed better biomechanical performance during a squat activity at 120° of flexion compared to the all-polyethylene design. These results should be considered when selecting the appropriate tibial component for a patient, especially in the presence of osteoporotic bone or if intense physical activity is foreseen.

Balancing UKA: overstuffing leads to high medial collateral ligament strains.

PURPOSE: Balancing unicondylar knee arthroplasty (UKA) is challenging. If not performed properly, it may lead to implant loosening or progression of osteoarthritis in the preserved compartment. This study was aimed to document the biomechanical effects of improper balancing. We hypothesised that overstuffing would lead to more valgus, higher strain in the medial collateral ligament (sMCL), and higher lateral contact force. METHODS: Six fresh-frozen cadaver specimens were mounted in a kinematic rig. Three motion patterns were applied with the native knee and following medial UKA (passive motion, open-chain extension, and squatting), while infrared cameras recorded the trajectories of markers attached to femur and tibia. Three inlay thicknesses were tested (8, 9, 10 mm). RESULTS: Overstuffed knees were in more valgus and showed less tibial rotation and higher strains in the sMCL (p < 0.05). Lateral contact forces were higher in some specimens and lower in others. Stiffening of the medial compartment by UKA, even well balanced, already leads to a knee more in valgus with a more stressed sMCL. Overstuffing increases these effects. Knees with a tight sMCL may even see lower lateral contact force. Biomechanics were closest to the native knee with understuffing. CONCLUSION: The first two hypotheses were confirmed, but not the latter. This underlines the importance of optimal balancing. Overstuffing should certainly be avoided. Although kinematics is only slightly affected, contact forces and ligament strains are considerably changed and this might be of more clinical importance. It is advisable to use thinner inlays, if stability is not compromised.

Fixation techniques and stem dimensions in hinged total knee arthroplasty: a finite element study.

INTRODUCTION: No evidence-based guidelines are available to determine the appropriate stem length, and whether or not to cement stems in revision total knee arthroplasty (TKA). Therefore, the objective of this study was to compare stresses and relative movement of cemented and uncemented stems of different lengths using a finite element analysis. MATERIALS AND METHODS: A finite element model was created for a synthetic tibia. Two stem lengths (95 and 160 mm) and two types of fixation (cemented or press fit) of a hinged TKA were examined. The average compressive stress distribution in different regions of interest, as well as implant micromotions, was determined and compared during lunge and squat motor tasks. RESULTS: Both long and short stems in revision TKA lead to high stresses, primarily in the region around the stem tip. The presence of cement reduces the stresses in the bone in every region along the stem. Short stem configurations are less affected by the presence of cement than the long stem configuration. Press-fit stems showed higher micromotions compared to cemented stems. CONCLUSIONS: Lowest stresses and micromotion were found for long cemented stems. Cementless stems showed more micromotion and increased stress levels especially at the level of the stem tip, which may explain the clinical phenomenon of stem-end pain following revision knee arthroplasty. These findings will help the surgeon with optimal individual implant choice.

Restoration of constitutional alignment in TKA leads to more physiological strains in the collateral ligaments.

PURPOSE: Currently, controversy exists whether restoration of neutral mechanical alignment should be attempted in all patients undergoing TKA. Our hypothesis was that restoration of constitutional rather than neutral mechanical alignment may in theory lead to a more physiological strain pattern in the collateral ligaments; therefore, it could potentially be beneficial to patients. Thus, the aim of this study was to measure collateral ligament strains during three motor tasks in the native knee and compare them with the strains noted after TKA in different post-operative alignment conditions. METHODS: Six cadaver specimens (approval number ML4190 from the Research Ethics Committee of University of Leuven, Belgium) were examined using a validated knee kinematics rig under physiological loading conditions. The effect of coronal malalignment was evaluated by using custom-made tibial implant inserts that induced different alignment conditions. The study of six specimens allows us to show that a difference in the mean strains in MCL and LCL of 3.6 and 5.8 %, respectively, was statistically significant with a probability (power) of 0.8. RESULTS: The results indicated that after TKA insertion, the strains in the collateral ligaments closely resembled the pre-operative pattern of the native knee specimens when constitutional alignment was restored. Restoration to neutral mechanical alignment was associated with greater collateral strain deviations from the native knee. CONCLUSION: Based upon this study, it was concluded that restoration of constitutional alignment within a "safe zone" of ±2° during TKA leads to more physiological peri-articular soft tissue strains during loaded as well as unloaded motor tasks.

The position of the tibia tubercle in 0°-90° flexion: comparing patients with patella dislocation to healthy volunteers.

PURPOSE: The aim of this study was to measure the tibia tubercle trochlea groove distance (TT-TG) as a function of knee flexion. Our hypothesis was that there is a different pattern in healthy volunteers and patients with patella instability (PFI). METHODS: Thirty-six knees of 30 patients with at least one dislocation of the patella and 30 knees of 30 healthy volunteers as control group were analysed with magnetic resonance imaging by three different observers. The TT-TG was measured in steps of 15° between 0° and 90° of knee flexion. Furthermore, the alignment of the leg (MA), the femur torsion (FTor) and the tibia torsion (TTor) was calculated. RESULTS: The TT-TG was higher in patients compared to volunteers and in extension compared to flexion. This difference was statistically significant (p<0.05). Most of the patients with a TT-TG above 20 mm in extension showed a high decrease in flexion to normal values. In some patients, this compensating mechanism fails. MA, FTor and TTor were not different in patients and control group (n.s.). CONCLUSION: The TT-TG distance is dynamic and decreased significantly during flexion in knees with PFI and healthy volunteers. However, there were a small number of patients in the PFI group where this compensation mechanism did not work. Therefore, the decision to perform a tibia tubercle osteotomy should not be based on one single measurement in extension or 30° of knee flexion. LEVEL OF EVIDENCE: II.

Patellofemoral arthroplasty influences tibiofemoral kinematics: the effect of patellar thickness.

PURPOSE: Although controversy still remains, isolated patellofemoral arthroplasty recently gained in popularity as a treatment option for patellofemoral osteoarthritis. It has compared to total knee arthroplasty the advantage of preserving the tibiofemoral articulation, which in theory would allow the preservation of natural tibiofemoral kinematics. Today, however, no data exist to support this assumption. This study was therefore performed in order to investigate the effect of isolated patellofemoral arthroplasty on the native three-dimensional tibiofemoral kinematic behaviour and whether a change in patellar thickness would have an influence. METHODS: Six fresh-frozen cadavers were fixed on a custom-made mechanical knee rig. Full 3D kinematics was analysed during passive flexion-extension cycles, open chain extension, with and without mechanical resistance, as well as deep knee squats, using infrared motion capture cameras and retroflective markers. Measurements were taken for the native knee and after prosthetic trochlear resurfacing with and without patellar resurfacing in three different patellar thicknesses. RESULTS: Compared to the natural knee, patellofemoral arthroplasty resulted in significant changes in tibiofemoral kinematics, which were most pronounced in the most loaded motor tasks. Increased internal tibial rotation was noted in the mid- and high flexion ranges, reaching at 120° of flexion a mean difference of 4.5°±4.3° (p<0.0001) during squat motion, over the whole flexion range during open chain motion and in deeper flexion beyond 50° (mean at 70°, 1.9°±3.7°) during resisted open chain. During squats, also, a more posterior translation of the lateral femoral condyle was observed. The effect was accentuated in case of patella overstuffing, whereas kinematics was closer to normal with patellar thinning. CONCLUSION: Isolated patellofemoral arthroplasty alters natural tibiofemoral kinematics, and the effects become more pronounced in case of increased patellar thickness. Therefore, it might be recommended to aim for a slight over-resection of patellar bone if sufficient bone stock is available.

UKA closely preserves natural knee kinematics in vitro.

PURPOSE: It is assumed that unicondylar knee arthroplasty (UKA) features kinematics close to the natural knee. Clinical studies have also shown functional benefits for UKA. There is to date only little biomechanical data to support or explain these findings. The purpose of this study was to investigate whether UKA is able to preserve natural knee kinematics or not. METHODS: Six fresh frozen full leg cadaver specimens were prepared to be mounted in a kinematic rig with six degrees of freedom for the knee joint. Three motion patterns were applied before and after medial UKA: passive flexion-extension, open chain extension, and squatting. During the loaded motions, quadriceps and hamstrings muscle forces were applied. Infrared cameras continuously recorded the trajectories of marker frames rigidly attached to femur, tibia, and patella. Prior computer tomography allowed identification of coordinate frames of the bones and calculations of anatomical rotations and translations. RESULTS: Native kinematics was reproduced after UKA in all the specimens. In the unloaded knee and during open chain extension, femoral rollback patterns after UKA were very close to those in the native knee. During squatting, the medial femoral condyle after UKA tended to be more posterior and superior with flexion and there was less tibial internal rotation. The tibia was found to be more in valgus after UKA during all motion patterns. CONCLUSION: As ligaments, lateral compartment and patellofemoral anatomy are preserved with UKA; the unloaded knee closely resembles native kinematics. The slight kinematic changes that were found under load are probably due to loss of the conforming medial meniscus and to the mismatch in geometry and stiffness introduced by UKA. These patterns resemble those found in knees with significant loss of function of the medial meniscus.

Load sharing and ligament strains in balanced, overstuffed and understuffed UKA. A validated finite element analysis.

The aim of this study was to quantify the effects of understuffing and overstuffing UKA on bone stresses, load distribution and ligament strains. For that purpose, a numerical knee model of a cadaveric knee was developed and was validated against experimental measurements on that same knee. Good agreement was found among the numerical and experimental results. This study showed that, even if a medial UKA is well-aligned with normal soft tissue tension and with correct thickness of the tibia component, it induces a stiffness modification in the joint that alters the load distribution between the medial and lateral compartments, the bone stress and the ligament strain potentially leading to an osteoarthritic progression.

Stemmed TKA in a femur with a total hip arthroplasty: is there a safe distance between the stem tips?

When a stemmed TKA is needed in a femur in which a THA is already present, choosing an appropriate length for the TKA stem is crucial. Many surgeons intuitively fear that the distance between the stem tips correlates with the femur risk for fracture (RF). However, to date, no biomechanical data to support this intuition are available. Therefore, in this study, the RF in such a configuration was determined and compared for several activities, using a finite element modeling technique. During gait and sideways falling no difference in RF among different stem lengths was shown. However, a clear threshold appears during four-point bending. Stem tip distances shorter than 110 mm dramatically increased RF and, in osteoporotic bone, will certainly lead to fracture (RF>1) and thus should be avoided.

The influence of freezing on the tensile strength of tendon grafts : a biomechanical study.

We investigated the influence of freezing on the tensile strength of fresh frozen tendon grafts. The biomechanical characteristics of tendons that are less commonly used in knee surgery (tibialis anterior, tibialis posterior, peroneus longus and medial and lateral half of Achilles tendons) were compared to those of a semitendinosus and gracilis graft harvested from the same 10 multi-organ donors. All right side tendons constituted the study group and were frozen at -80 degrees C and thawed at room temperature 5 times. All left side tendons were frozen at -80 degrees C and thawed at room temperature once. There were 59 tendons in the control group and 56 in the study group. The looped grafts were clamped at one side using a custom-made freeze clamp and loaded until failure on an Instron 4505 testing machine. The average ultimate failure load was not significantly different between the control and the study group (p > 0.05). The failure load of the medial tendon Achilles was the lowest in both study and control group (p < 0.001). There was no significant difference in maximum stress, maximum displacement, maximum strain and stiffness between the control and study group (p > 0.05). From our study, we conclude that freezing tendons at -80 degrees C and thawing several times does not influence the maximum load, maximum stress, maximum displacement, maximum strain and stiffness. The medial half of the Achilles tendon is clearly the weakest tendon (p < 0.001). These findings show that tendon grafts can be frozen at -80 degrees C and thawed at room temperature several times without altering their biomechanical properties.

The influence of ankle-foot orthoses on gait pathology in children with cerebral palsy: A retrospective study.

BACKGROUND: Ankle-foot orthoses (AFOs) are frequently prescribed in children with cerebral palsy (CP) to improve their gait. Due to the heterogeneous nature of CP and contradictions among previous studies, it is important to evaluate the AFO-specific effects, as well as explore their effects on different gait patterns. RESEARCH QUESTIONS: a) What are the prevalence and specific features of AFOs in children with CP? b) How do AFOs affect gait pathology in children with CP? c) What are the pattern-specific effects of AFOs in children with CP? METHODS: A group of 170 patients with CP underwent a three-dimensional gait analysis with and without AFOs (either carbon fiber, rigid, flexible or hinged). The gait profile score, the gait variable scores of the hip, knee and ankle joints, non-dimensional step length and walking speed were used as outcome measures. The AFO-specific effects on the kinematic and kinetic waveforms were investigated using statistical non-parametric mapping (SnPM). Effects were considered relevant when the minimal clinically important difference (MCID) or the standard errors of measurement, for the parameters or the waveforms respectively, were exceeded. RESULTS: Rigid AFOs were prescribed for more than 80 % of the children. Significant beneficial effects were observed for non-dimensional step length and walking speed. Most changes in gait indices were not considered relevant. The SnPM-analyses on the total group and specific gait patterns revealed that walking with AFOs improved the kinematic and kinetic waveforms. These effects were relevant, and were most obvious for crouch, apparent equinus and the total group. SIGNIFICANCE: The use of AFOs improves gait, whether we inspect a total -and thus heterogeneous- group or focus on specific gait patterns. However, focussing on specific parameters (i.e. general gait indices) does not provide a full picture of the AFO-effects.

Cementing the tibial component in total knee arthroplasty: which technique is the best?

Aseptic loosening of the tibial component remains a major cause of failure in total knee arthroplasty and may be related, directly or indirectly, to micromotion. Therefore, good fixation of the tibial component is a prerequisite to achieve long-term success of the implant. Cementing technique is one of the factors that play a role in this respect. We investigated the effect of different cementing techniques on the cement penetration in the proximal tibia. We compared 5 different cementing techniques in an anatomical open pore sawbone model (n = 25), using a contemporary total knee arthroplasty design and standard polymethylmetacrylate cement. We demonstrated that applying cement to both the undersurface of the tibial baseplate and as well as onto the tibial bone, either by a spatula or fingerpacking technique, leads to an optimal cement penetration of 3 to 5 mm. When cement is applied only onto the tibial component, penetration is insufficient. When a cement gun is used, cement penetration is too excessive.

The Mark Coventry Award: Articular contact estimation in TKA using in vivo kinematics and finite element analysis.

In vivo fluoroscopy is a well-known technique to analyze joint kinematics of the replaced knee. With this method, however, the contact areas between femoral and tibial components, fundamental for monitoring wear and validating design concepts, are hard to identify. We developed and tested a novel technique to assess condylar and post-cam contacts in TKA. The technique uses in vivo motion data of the replaced knee from standard fluoroscopy as input for finite element models of the prosthesis components. In these models, tibiofemoral contact patterns at the condyles and post-cam articulations were calculated during various activities. To test for feasibility, the technique was applied to a bicruciate posterior-stabilized prosthesis. Sensitivity of the finite element analysis, validation of the technique, and in vivo tests were performed. To test for potential in the clinical setting, five patients were preliminarily analyzed during chair rising-sitting, stair climbing, and step up-down. For each task and patient, the condylar contact points and contact line rotation were calculated. The results were repeatable and consistent with corresponding calculations from traditional fluoroscopic analysis. Specifically, natural knee kinematics, which shows rolling back and screw home, seemed replicated in all motor tasks. Post-cam contact was observed on both the anterior and posterior faces. Anterior contact is limited to flexion angle close to extension; posterior contact occurs in deeper flexion but is dependent on the motor task. The data suggest the proposed technique provides reliable information to analyze post-cam contacts.

Distal femoral bone mineral density decreases following patellofemoral arthroplasty: 1-year follow-up study of 14 patients.

BACKGROUND: The bone mineral density (BMD) of the distal femur decreases by 16-36% within one year after total knee arthroplasty (TKA) because of the femoral component's stress-shielding effect. The aim of this prospective study was to determine the quantitative change from the baseline BMD in the distal femur 1 year after patellofemoral arthroplasty using dual-energy X-ray absorptiometry (DXA). METHODS: Between December 2007 and December 2008, 14 patients had patellofemoral arthroplasty for isolated patellofemoral osteoarthritis. Distal femoral BMD was assessed using DXA in 2 regions of interest (ROI) on the lateral view 2 weeks before and 12 months after patellofemoral arthroplasty. The contra-lateral knee was used as a control, with BMD measurements performed in identical ROIs. RESULTS: The mean change from baseline BMD in the operated knees after 1 year was -0.169 g/cm2 (95% CI: -0.293 to -0.046 g/cm2) behind the anterior flange (-15%), and -0.076 g/cm2 (95% CI: -0.177 to 0.024 g/cm2) in the supracondylar area 1 cm above the prosthesis (-8%) (p = 0.01 and p = 0.13, respectively). The mean change from baseline BMD in the non-operated knees after 1 year was 0.016 g/cm2 (95% CI: -0.152 to 0.185 g/cm2) behind the anterior flange (2%), and 0.023 g/cm2 (95% CI: -0.135 to 0.180 g/cm2) in the supracondylar area 1 cm above the prosthesis (2%) (p = 0.83, and p = 0.76, respectively). CONCLUSIONS: Our findings suggest that patellofemoral arthroplasty results in a statistically significant decrease in BMD behind the anterior flange.