Experimental and numerical study of submonolayer sputter deposition of polystyrene fragments on silver for the storing matter technique.

In static secondary ion mass spectrometry (SIMS), quantification and high ionization probabilities are difficult to obtain. The Storing Matter technique has been developed to circumvent these issues and has already been applied to deposit inorganic and organic samples. For organic samples, the effect of fragmentation during sputter deposition and changing coverage on time-of-flight (TOF)-SIMS mass spectra has not been investigated. In this work, polystyrene (PS) was sputter deposited on silver using an argon ion beam in order to investigate these parameters and to get a better control of the whole process. For this purpose, we introduce a multitechnique characterization approach for the submonolayer deposition of PS. Experimental methods (TOF-SIMS, X-ray photoelectron spectroscopy (XPS)) were used in combination with simulations (density functional theory (DFT) calculations) in order to obtain information about the molecular and structural changes and the interactions of organic matter with the metal surface. Alterations of the PS surface and PS sputter deposit as a function of surface coverage and Ar(+) ion fluence are addressed. A major finding is that this approach can be used to identify surface reactions between different fragments on the collector surface. Indeed, in the dynamic regime, the ratio of large to small fragments is increasing although the fragmentation during the sputter deposition should lead to increasingly smaller fragments. Hence, for Storing Matter, the coverage on the collector must be kept low in order to minimize the reactions between fragments and to preserve the information on the original sample.

High Voltage Cycling Stability of LiF-Coated NMC811 Electrode.

The development of LiNi0.8Mn0.1Co0.1O2 (NMC811) as a cathode material for high-energy-density lithium-ion batteries (LIBs) intends to address the driving limitations of electric vehicles. However, the commercialization of this technology has been hindered by poor cycling stability at high cutoff voltages. The potential instability and drastic capacity fade stem from irreversible parasitic side reactions at the electrode-electrolyte interface. To address these issues, a stable nanoscale lithium fluoride (LiF) coating is deposited on the NMC811 electrode via atomic layer deposition. The nanoscale LiF coating diminishes the direct contact between NMC811 and the electrolyte, suppressing the detrimental parasitic reactions. LiF-NMC811 delivers cycling stability superior to uncoated NMC811 with high cutoff voltage for half-cell (3.0-4.6 V vs Li/Li+) and full-cell (2.8-4.5 V vs graphite) configurations. The structural, morphological, and chemical analyses of the electrodes after cycling show that capacity decline fundamentally arises from the electrode-electrolyte interface growth, irreversible phase transformation, transition metal dissolution and crossover, and particle cracking. Overall, this work demonstrates that LiF is an effective electrode coating for high-voltage cycling without compromising rate performance, even at high discharge rates. The findings of this work highlight the need to stabilize the electrode-electrolyte interface to fully utilize the high-capacity performance of NMC811.

The effect of the pyrolysis temperature and biomass type on the biocarbons characteristics.

The conversion of biomass and natural wastes into carbon-based materials for various applications such as catalysts and energy-related materials is a fascinating and sustainable approach emerged during recent years. Precursor nature and characteristics are complex, hence, their effect on the properties of resulting materials is still unclear. In this work, we have investigated the effect of different precursors and pyrolysis temperature on the properties of produced carbon materials and their potential application as negative electrode materials in Li-ion batteries. Three biomasses, lignocellulosic brewery spent grain from a local brewery, catechol-rich lignin and tannins, were selected for investigations. We show that such end-product carbon characteristic as functional and elemental composition, porosity, specific surface area, defectiveness level, and morphology strictly depend on the precursor composition, chemical structure, and pyrolysis temperature. The electrochemical characteristics of produced carbon materials correlate with the characteristics of the produced materials. A higher pyrolysis temperature is shown to be favourable for production of carbon material for the Li-ion battery application in terms of both specific capacity and long-term cycling stability.

Droplet slipperiness despite surface heterogeneity at molecular scale.

Friction determines whether liquid droplets slide off a solid surface or stick to it. Surface heterogeneity is generally acknowledged as the major cause of increased contact angle hysteresis and contact line friction of droplets. Here we challenge this long-standing premise for chemical heterogeneity at the molecular length scale. By tuning the coverage of self-assembled monolayers (SAMs), water contact angles change gradually from about 10° to 110° yet contact angle hysteresis and contact line friction are low for the low-coverage hydrophilic SAMs as well as high-coverage hydrophobic SAMs. Their slipperiness is not expected based on the substantial chemical heterogeneity of the SAMs featuring uncoated areas of the substrate well beyond the size of a water molecule as probed by metal reactants. According to molecular dynamics simulations, the low friction of both low- and high-coverage SAMs originates from the mobility of interfacial water molecules. These findings reveal a yet unknown and counterintuitive mechanism for slipperiness, opening new avenues for enhancing the mobility of droplets.

Facile Fabrication of Ni9 S8 /Ag2 S Intertwined Structures for Oxygen and Hydrogen Evolution Reactions.

Here, we report the fabrication of the unique intertwined Ni9 S8 /Ag2 S composite structure with hexagonal shape from their molecular precursors by one-pot thermal decomposition. Various spectroscopic and microscopic techniques were utilized to confirm the Ni9 S8 /Ag2 S intertwined structure. Powder X-ray Powder Diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analysis suggest that there is an enrichment of Ni9 S8 phase in Ni9 S8 /Ag2 S. The presence of Ag2 S in Ni9 S8 /Ag2 S improves the conductivity by reducing the interfacial energy and charge transfer resistance. When Ni9 S8 /Ag2 S is employed as an electrocatalyst for electrochemical oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) activity, it requires a low overpotential of 152 mV for HER and 277 mV for OER to obtain the geometrical current density of 10 mA cm-2 , which is definitely superior to that of its components Ni9 S8 and Ag2 S. This work provides a simple design route to develop an efficient and durable electrocatalyst with outstanding OER and HER performance and the present catalyst (Ni9 S8 /Ag2 S) deserves as a potential candidate in the field of energy conversion systems.

Dumbbell-Shaped Ternary Transition-Metal (Cu, Ni, Co) Phosphate Bundles: A Promising Catalyst for the Oxygen Evolution Reaction.

Development of economical and high-performance electrocatalysts for the oxygen evolution reaction (OER) is of tremendous interest for future applications as sustainable energy materials. Here, a unique member of efficient OER electrocatalysts has been developed based upon structurally versatile dumbbell-shaped ternary transition-metal (Cu, Ni, Co) phosphates with a three-dimensional (3D) (Cu2(OH)(PO4)/Ni3(PO4)2·8H2O/Co3(PO4)2·8H2O) (CNCP) structure. This structure is prepared using a simple aqueous stepwise addition of metal ion source approach. Various structural investigations demonstrate highly crystalline nature of the composite structure. Apart from the unique structural aspect, it is important that the CNCP composite structure has proved to be an excellent electrocatalyst for OER performance in comparison with its binary or constituent phosphate under alkaline and neutral conditions. Notably, the CNCP electrocatalyst displays a much lower overpotential of 224 mV at a current density of 10 mA cm-2 and a lower Tafel slope of 53 mV dec-1 with high stability in alkaline medium. In addition, X-ray photoelectron spectroscopy analysis suggested that the activity and long-term durability for the OER of the ternary 3D metal phosphate are due to the presence of electrochemically dynamic constituents such as Ni and Co and their resulting synergistic effects, which was further supported by theoretical studies. Theoretical calculations also reveal that the incredible OER execution was ascribed to the electron redistribution set off in the presence of Ni and Cu and the most favorable interaction between the *OOH intermediate and the active sites of CNCP. This work may attract the attention of researchers to construct efficient 3D ternary metal phosphate catalysts for various applications in the field of electrochemistry.

Tuning of Emission Wavelength of CaS:Eu by Addition of Oxygen Using Atomic Layer Deposition.

Atomic layer deposition (ALD) technology has unlocked new ways of manipulating the growth of inorganic materials. The fine control at the atomic level allowed by ALD technology creates the perfect conditions for the inclusion of new cationic or anionic elements of the already-known materials. Consequently, novel material characteristics may arise with new functions for applications. This is especially relevant for inorganic luminescent materials where slight changes in the vicinity of the luminescent centers may originate new emission properties. Here, we studied the luminescent properties of CaS:Eu by introducing europium with oxygen ions by ALD, resulting in a novel CaS:EuO thin film. We study structural and photoluminescent properties of two different ALD deposited Eu doped CaS thin films: Eu(thd)3 which reacted with H2S forming CaS:Eu phosphor, or with O3 originating a CaS:EuO phosphor. It was found that the emission wavelength of CaS:EuO was 625.8 nm whereas CaS:Eu was 647 nm. Thus, the inclusion of O2- ions by ALD in a CaS:Eu phosphor results in the blue-shift of 21.2 nm. Our results show that ALD can be an effective way to introduce additional elements (e.g., anionic elements) to engineer the physical properties (e.g., inorganic phosphor emissions) for photonics and optoelectronics.

Understanding the Stabilizing Effects of Nanoscale Metal Oxide and Li-Metal Oxide Coatings on Lithium-Ion Battery Positive Electrode Materials.

Nickel-rich layered oxides, such as LiNi0.6Co0.2Mn0.2O2 (NMC622), are high-capacity electrode materials for lithium-ion batteries. However, this material faces issues, such as poor durability at high cut-off voltages (>4.4 V vs Li/Li+), which mainly originate from an unstable electrode-electrolyte interface. To reduce the side reactions at the interfacial zone and increase the structural stability of the NMC622 materials, nanoscale (<5 nm) coatings of TiOx (TO) and LixTiyOz (LTO) were deposited over NMC622 composite electrodes using atomic layer deposition. It was found that these coatings provided a protective surface and also reinforced the electrode structure. Under high-voltage range (3.0-4.6 V) cycling, the coatings enhance the NMC electrochemical behavior, enabling longer cycle life and higher capacity. Cyclic voltammetry, X-ray photoelectron spectroscopy, and X-ray diffraction analyses of the coated NMC electrodes suggest that the enhanced electrochemical performance originates from reduced side reactions. In situ dilatometry analysis shows reversible volume change for NMC-LTO during the cycling. It revealed that the dilation behavior of the electrode, resulting in crack formation and consequent particle degradation, is significantly suppressed for the coated sample. The ability of the coatings to mitigate the electrode degradation mechanisms, illustrated in this report, provides insight into a method to enhance the performance of Ni-rich positive electrode materials under high-voltage ranges.

Giant anisotropic photonics in the 1D van der Waals semiconductor fibrous red phosphorus.

A confined electronic system can host a wide variety of fascinating electronic, magnetic, valleytronic and photonic phenomena due to its reduced symmetry and quantum confinement effect. For the recently emerging one-dimensional van der Waals (1D vdW) materials with electrons confined in 1D sub-units, an enormous variety of intriguing physical properties and functionalities can be expected. Here, we demonstrate the coexistence of giant linear/nonlinear optical anisotropy and high emission yield in fibrous red phosphorus (FRP), an exotic 1D vdW semiconductor with quasi-flat bands and a sizeable bandgap in the visible spectral range. The degree of photoluminescence (third-order nonlinear) anisotropy can reach 90% (86%), comparable to the best performance achieved so far. Meanwhile, the photoluminescence (third-harmonic generation) intensity in 1D vdW FRP is strong, with quantum efficiency (third-order susceptibility) four (three) times larger than that in the most well-known 2D vdW materials (e.g., MoS2). The concurrent realization of large linear/nonlinear optical anisotropy and emission intensity in 1D vdW FRP paves the way towards transforming the landscape of technological innovations in photonics and optoelectronics.

Electronic and Magnetic Characterization of Epitaxial CrBr3 Monolayers on a Superconducting Substrate.

The ability to imprint a given material property to another through a proximity effect in layered 2D materials has opened the way to the creation of designer materials. Here, molecular-beam epitaxy is used for direct synthesis of a superconductor-ferromagnet heterostructure by combining superconducting niobium diselenide (NbSe2 ) with the monolayer ferromagnetic chromium tribromide (CrBr3 ). Using different characterization techniques and density-functional theory calculations, it is confirmed that the CrBr3 monolayer retains its ferromagnetic ordering with a magnetocrystalline anisotropy favoring an out-of-plane spin orientation. Low-temperature scanning tunneling microscopy measurements show a slight reduction of the superconducting gap of NbSe2 and the formation of a vortex lattice on the CrBr3 layer in experiments under an external magnetic field. The results contribute to the broader framework of exploiting proximity effects to realize novel phenomena in 2D heterostructures.

Effect of Polishing on Electrochemical Behavior and Passive Layer Composition of Different Stainless Steels.

In the present paper, the effect of different polishing methods (mechanical and electrochemical) on passive layer chemistry and the corrosion behavior of stainless steels is investigated. It was found that CrNiMo austenites have a substantially better corrosion behavior than CrMnN ones. The nickel is enriched underneath the passive layer, while manganese tends to be enriched in the passive layer. It was also noted that immersion of manganese into an electrolyte preferentially causes its dissolution. It was found that high amounts of chromium (27.4%), molybdenum (3.3%), nickel (29.4%), with the addition of manganese (2.8%) after mechanical grinding, generates a better corrosion resistance than after electrochemical polishing. This is most likely because of the introduction of phosphates and sulfates into its structure, which is known for steels with a high amount of manganese. For highly alloyed CrNiMo steels, which do not contain a high amount of manganese, the addition of phosphates and/or sulphates via the electropolishing process results in a decrease in pitting corrosion resistance, which is also observed for high manganese steels. Electropolished samples show detrimental corrosion properties when compared to mechanically polished samples. This is attributed to substantial amounts of sulfate and phosphate from the electropolishing electrolyte present in the surface of the passive layer.

Noble copper-silver-gold trimetallic nanobowls: An efficient catalyst.

We demonstrated the design of tiny bowls of copper-silver-gold (Cu-Ag-Au) alloy type noble trimetallic nanocrystals with a unique shape. All the structural characterizations confirm the presence of copper (Cu), silver (Ag), and gold (Au) in the trimetallic nanobowls. Finally, we examined the catalytic efficiency of trimetallic Cu-Ag-Au nanobowls for reduction of 4-nitrophenol to 4-aminophenol and found that these nanobowls were 14, 23 and 43-fold more active than each of the constituent metals, Au, Cu and Ag, respectively.

Titania nanotubes prepared by rapid breakdown anodization for photocatalytic decolorization of organic dyes under UV and natural solar light.

Titania nanotube (TNT) powder was prepared by rapid breakdown anodization (RBA) in a perchloric acid electrolyte. The photocatalytic efficiency of the as-prepared and powders annealed at temperatures between 250 and 550 °C was tested under UV and natural sunlight irradiation by decolorization of both anionic and cationic organic dyes, i.e., methyl orange (MO) and rhodamine B (RhB), as model pollutants. The tubular structure of the nanotubes was retained up to 250 °C, while at 350 °C and above, the nanotubes transformed into nanorods and nanoparticles. Depending on the annealing temperature, the TNTs consist of anatase, mixed anatase/brookite, or anatase/rutile phases. The bandgap of the as-prepared nanotubes is 3.04 eV, and it shifts towards the visible light region upon annealing. The X-ray photoelectron spectroscopy (XPS) results show the presence of titania and impurities including chlorine on the surface of the TNTs. The atomic ratio of Ti/O remains unchanged for the annealed TNTs, but the concentration of chlorine decreases with temperature. The photoluminescence (PL) indicate high electron-hole recombination for the as-prepared TNTs, probably due to the residual impurities, low crystallinity, and vacancies in the structure, while the highest photocurrent was observed for the TNT sample annealed at 450 °C. The TNTs induce a small degradation of the dyes under UV light; however, contrary to previous reports, complete decolorization of dyes is observed under sunlight. All TNT samples showed higher decolorization rates under sunlight irradiation than under UV light. The highest reaction rate for the TNT samples was obtained for the as-prepared TNT powder sample under sunlight using RhB (κ1 = 1.29 h-1). This is attributed to the bandgap, specific surface area and the crystal structure of the nanotubes. The as-prepared TNTs performed most efficiently for decolorization of RhB and outperformed the reference anatase powder under sunlight irradiation. This could be attributed to the abundance of reactive sites, higher specific surface area, and degradation mechanism of RhB. These RBA TNT photocatalyst powders demonstrate a more efficient use of the sunlight spectrum, making them viable for environmental remediation.

Experimental humidity dependency of small particle adhesion on silica and titania.

The humidity present in ambient atmosphere affects the adhesion of small particles by causing capillary bridge formation between the particle and the surface. Even in moderate relative humidities this, usually attractive, force can have a significant effect on adhesion behaviour of micro and sub-micro particles. We have directly measured the pull-off forces of initially adhered oxide particles on oxide surfaces with atomic force microscope in controlled atmosphere with adjustable humidity. We demonstrate the effect of the surface roughness resulting in two different regions of capillary formation and the particle shape having a strong effect on the humidity dependency of adhesion. The experimental results are explained by theoretical framework.

Optimizing the sputter deposition process of polymers for the Storing Matter technique using PMMA.

Quantitative analyses in secondary ion mass spectrometry (SIMS) become possible only if ionization processes are controlled. The Storing Matter technique has been developed to circumvent this so-called matrix effect, primarily for inorganic samples, but has also been extended to organic samples. For the latter, it has been applied to polystyrene in order to investigate the extent of damage in the polymer, its fragmentation during the sputter deposition process and the effect of the deposition process on the spectra taken by Time-of-Flight SIMS (ToF-SIMS). In this work, a multi-technique approach, which employs the Storing Matter technique for deposition and ToF-SIMS and X-ray photoelectron spectroscopy for characterization, is used to enhance the control of the deposition process, including the thickness of the deposit, the alteration of the source film and the influence of polymer composition on the Storing Matter process. Poly (methyl methacrylate) (PMMA) is used for this work. More detailed information about the sticking of polymer fragments on the metal collector is obtained by density functional theory calculations. This work allows for the conclusion that a part of the fragments deposited on the collector surface diffuses on the latter, reacts and recombines to form larger fragments. The behaviour observed for PMMA is similar to polystyrene, showing that oxygen has no major influence on the processes occurring during the sputter deposition process. Additionally, we have developed a new methodology using 2D ToF-SIMS images of the deposit to monitor the deposit thickness and to identify surface contaminations. The latter are not only located at the position of the deposit but all over the collector surface. Copyright © 2016 John Wiley & Sons, Ltd.

Hybrid colloidal Au-CdSe pentapod heterostructures synthesis and their photocatalytic properties.

In this report, we present a self-driven chemical process to design exclusive Au/CdSe pentapod heterostructures with Au core and CdSe arms. We have analyzed these heterostructures using high-resolution transmission electron microscope (HRTEM), high angle annular dark field-scanning transmission electron microscopic (HAADF-STEM), X-ray diffraction, and X-ray photoelectron spectroscopy (XPS) studies. Microscopic studies suggest that pentapod arms of CdSe are nucleated on the (111) facets of Au and linearly grown only along the [001] direction. From the XPS study, the shifting of peak positions in the higher binding energy region for Au/CdSe heterostructures compared to Au nanoparticles has been found which indicates the charge transfer from CdSe to Au in heterostructures. The steady state and time resolved spectroscopic studies unambiguously confirm the electron transfer from photoexcited CdSe to Au, and the rate of electron transfer is found to be 3.58×108 s⁻¹. It is interesting to note that 87.2% of R6G dye is degraded by the Au/CdSe heterostructures after 150 min UV irradiation, and the apparent rate constant for Au/CdSe heterostructures is found to be 0.013 min⁻¹. This new class of metal-semiconductor heterostructures opens up new possibilities in photocatalytic, solar energy conversion, photovoltaic, and other new emerging applications.