Designing lightweight neutron absorbing composites using a comprehensive absorber areal density metric.

Efforts to lightweight neutron absorbing composites are limited by incomplete understandings of the interaction between absorbing particles and their matrices. In this study, analytical models and a more physically representative simulation evaluated the penalty to neutron absorbing performance due to neutron channeling between large absorbing particles. Models and simulation agreed that B4C particles smaller than 100µm and especially those smaller than 10µm did not cause excessive neutron channeling. A more comprehensive neutron absorbing composite design metric - boron-10 equivalent areal density, which considers the particle size penalty and the matrix contribution to absorptivity - was introduced and used to estimate lightweighting via matrix substitution. Calculations using this new metric showed that a non-absorbing Mg matrix reduced mass by up to 35% over Al, constrained by the difference in mass density, while an absorbing Mg-Li matrix reduced mass by up to 60%, exceeding the difference in mass densities alone. Measurement of apparent absorber areal density through two experimental techniques - foil activation and direct counting - validated estimated absorber areal density as a neutron absorbing composite design metric. This updated understanding of the particle size penalty, newly introduced design metric, and experimental validation demonstrate a path to lightweight neutron absorbing composites.

The effect of Mg-Ca-Sr alloy degradation products on human mesenchymal stem cells.

Biodegradable Mg alloys have the potential to replace currently used metallic medical implant devices, likely eliminating toxicity concerns and the need for secondary surgeries, while also providing a potentially stimulating environment for tissue growth. A recently developed Mg-Ca-Sr alloy possesses advantageous characteristics over other Mg alloys, having a good combination of strength and degradation behavior, while also displaying potentially osteogenic properties. To better understand the effect of alloy degradation products on cellular mechanisms, in vitro studies using human bone marrow-derived mesenchymal stem cells were conducted. Ionic products of alloy dissolution were found to be nontoxic but changed the proliferation profile of stem cells. Furthermore, their presence changed the progress of osteogenic development, while concentrations of Mg in particular appeared to induce stem cell differentiation. The work presented herein provides a foundation for future alloy design where structures can be tailored to obtain specific implant performance. These potentially bioactive implants would reduce the risks for patients by shortening their healing time, minimizing discomfort and toxicity concerns, while reducing hospital costs. © 2017 The Authors Journal of Biomedical Materials Research Part B: Applied Biomaterials Published by Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 697-704, 2018.

Mechanical and degradation property improvement in a biocompatible Mg-Ca-Sr alloy by thermomechanical processing.

Magnesium-based alloys have attracted interest as a potential material to comprise biomedical implants that are simultaneously high-strength and temporary, able to provide stabilization before degrading safely and able to be excreted by the human body. Many alloy systems have been evaluated, but this work reports on improved properties through hot extrusion of one promising alloy: Mg-1.0 wt% Ca-0.5 wt%Sr. This alloy has previously demonstrated promising toxicity and degradation properties in the as-cast and rolled conditions. In the current study extrusion causes a dramatic improvement in the mechanical properties in tension and compression, as well as a low in vitro degradation rate. Microstructure (texture, second phase distribution, and grain size), bulk mechanical properties, flow behavior, degradation in simulated body fluid, and effect on osteoblast cyctotoxicity are evaluated and correlated to extrusion temperature. Maximum yield strength of 300 MPa (above that of annealed 316 stainless steel) with 10% elongation is observed, making this alloy competitive with existing implant materials.

Peri-implant tissue response and biodegradation performance of a Mg-1.0Ca-0.5Sr alloy in rat tibia.

Biodegradable magnesium (Mg) alloys combine the advantages of traditional metallic implants and biodegradable polymers, having high strength, low density, and a stiffness ideal for bone fracture fixation. A recently developed Mg-Ca-Sr alloy potentially possesses advantageous characteristics over other Mg alloys, such as slower degradation rates and minimal toxicity. In this study, the biocompatibility of this Mg-Ca-Sr alloy was investigated in a rat pin-placement model. Cylindrical pins were inserted in the proximal tibial metaphyses in pre-drilled holes orthogonal to the tibial axis. Implant and bone morphologies were investigated using µCT at 1, 3, and 6 weeks after implant placement. At the same time points, the surrounding tissue was evaluated using H&E, TRAP and Goldner's trichrome staining. Although gas bubbles were observed around the degrading implant at early time points, the bone remained intact with no evidence of microfracture. Principle findings also include new bone formation in the area of the implant, suggesting that the alloy is a promising candidate for biodegradable orthopedic implants.

The role of surface oxidation on the degradation behavior of biodegradable Mg-RE (Gd, Y, Sc) alloys for resorbable implants.

Biodegradable magnesium (Mg) alloys have the potential to replace currently used implants for fixation, thereby eliminating the need for removal surgeries. To achieve a controllable degradation rate, surface oxidation has been proposed as an avenue to reduce the initial degradation. This study aims to investigate the oxidation behavior of binary Mg-rare earth alloys and the effect on biodegradation. Cast Mg-3X alloys (X=Gd, Y, Sc) were prepared and then oxidized in pure oxygen. The oxidation rate was evaluated using TGA and the oxides were further investigated and characterized using SEM, AES and XPS. The effect of oxidation on the degradation rate was investigated by immersion testing in Hanks' solution. The thermodynamics and oxidation kinetics of the alloys are discussed in regard to the obtained results, and it was concluded that the experimental results are in agreement with thermodynamic predictions.

A study of a biodegradable Mg-3Sc-3Y alloy and the effect of self-passivation on the in vitro degradation.

Magnesium and its alloys have been investigated for their potential application as biodegradable implant materials. Although properties of magnesium such as biocompatibility and susceptibility to dissolution are desirable for biodegradable implant applications, its high degradation rate and low strength pose a significant challenge. A potential way to reduce the initial degradation rate is to form a self-passivating protective layer on the surface of the alloy. Oxides with a low enthalpy of formation result in a strong thermodynamic driving force to produce oxide surfaces that are more stable than the native oxide (MgO), and possibly reduce the initial degradation rate in these alloys. In the present study a ternary Mg-3wt.% Sc-3wt.% Y alloy was investigated and its oxidation behavior studied. The effect of surface passivation on the in vitro degradation rate was studied and the degradation products identified. The results show that the oxide provided an initial degradation barrier and 24h oxidation resulted in a negligible degradation rate for up to 23 days. Furthermore, the degradation products of the alloy showed no significant toxicity to osteoblastic cells, and cell proliferation studies confirmed cell attachment and proliferation on the surface of the oxidized alloy.

MR measurement of alloy magnetic susceptibility: towards developing tissue-susceptibility matched metals.

Magnetic resonance imaging (MRI) can be used to relate structure to function mapped with high-temporal resolution electrophysiological recordings using metal electrodes. Additionally, MRI may be used to guide the placement of electrodes or conductive cannula in the brain. However, the magnetic susceptibility mismatch between implanted metals and surrounding brain tissue can severely distort MR images and spectra, particularly in high magnetic fields. In this study, we present a modified MR method of characterizing the magnetic susceptibility of materials that can be used to develop biocompatible, metal alloys that match the susceptibility of host tissue in order to eliminate MR distortions proximal to the implant. This method was applied at 4.7T and 11.1T to measure the susceptibility of a model solid-solution alloy of Cu and Sn, which is inexpensive but not biocompatible. MR-derived relative susceptibility values of four different compositions of Cu-Sn alloy deviated by less than 3.1% from SQUID magnetometry absolute susceptibility measurements performed up to 7T. These results demonstrate that the magnetic susceptibility varies linearly with atomic percentage in these solid-solution alloys, but are not simply the weighted average of Cu and Sn magnetic susceptibilities. Therefore susceptibility measurements are necessary when developing susceptibility-matched, solid-solution alloys for the elimination of susceptibility artifacts in MR. This MR method does not require any specialized equipment and is free of geometrical constraints, such as sample shape requirements associated with SQUID magnetometry, so the method can be used at all stages of fabrication to guide the development of a susceptibility matched, biocompatible device.

Investigation of the mechanical and degradation properties of Mg-Sr and Mg-Zn-Sr alloys for use as potential biodegradable implant materials.

Magnesium (Mg) has garnered significant interest for its potential use as a biodegradable implant material. Of specific interest in this study is the effect of zinc (Zn) and strontium (Sr) additions on both the mechanical and degradation behaviors in Mg due to their established beneficial effect on strength and microstructural grain refinement while being biocompatible. Three binary Mg-x wt% Sr (x=0.5, 1.0, 1.5) alloys and three ternary Mg-x wt%Zn-0.5 wt% Sr (x=2.0, 4.0, 6.0) were studied to evaluate their mechanical and degradation behavior. Mechanical testing was performed at room temperature on solution-treated and peak aged alloys using microhardness and tensile tests. Degradation was studied using immersion tests in Hanks' solution. Results indicate a decrease in grain size and an increase in strength with increasing Sr and Zn content. When considering degradation behavior Mg-0.5 wt%Sr demonstrated the lowest degradation rate among binary alloys. At constant Sr content at 0.5 wt%, the addition of Zn increased the corrosion rate, with the highest rate for the Mg-6.0 wt%Zn-0.5 wt%Sr. The alloys which best optimized both mechanical and degradation behaviors were Mg-2.0 wt%Zn-0.5 wt%Sr and Mg-4.0 wt%Zn-0.5 wt%Sr. Finally, microstructure and property relationships were evaluated and discussed in reference to each alloy's potential use as a biodegradable implant material.

Synthesis and characterization of Mg-Ca-Sr alloys for biodegradable orthopedic implant applications.

Magnesium has recently received an increased amount of interest due to its potential use in biodegradable implant applications. The rapid degradation of conventional Mg is, however, a major limitation that needs to be addressed in the design of these materials, along with consideration of toxicity in selection of alloying elements. In this study, five alloys in the Mg-xCa-ySr system (x = 0.5-7.0 wt %; y = 0.5-3.5 wt %) were prepared and characterized for their suitability as degradable orthopedic implant materials. The alloys were characterized using optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, degradation measurements in Hanks' solution at 37°C, compression testing, and in vitro cytotoxicity testing with a mouse osteoblastic cell line. The results indicate that the Mg-1.0Ca-0.5Sr alloy is the most promising alloy for orthopedic implant applications since it showed the lowest degradation rate in Hanks' solution (0.01 mL cm(-2) h(-1)) along with no significant toxicity to MC3T3-E1 osteoblasts and a compressive strength of 274 ± 4 MPa.