Multimethod analysis of large- and low-tapered single file reciprocating instruments: Design, metallurgy, mechanical performance, and irrigation flow.

AIM: To compare eight large- and low-tapered heat-treated reciprocating instruments regarding their design, metallurgy, mechanical properties, and irrigation flow through an in silico model. METHODOLOGY: A total of 472 new 25-mm E-Flex Rex (25/.04 and 25/.06), Excalibur (25/.05), Procodile (25/.06), Reciproc Blue R25 (25/.08v), WaveOne Gold Primary (25/.07v), and Univy Sense (25/.04 and 25/.06) instruments were evaluated regarding their design (stereomicroscopy, scanning electron microscopy, and 3D surface scanning), metallurgy (energy-dispersive X-ray spectroscopy and differential scanning calorimetry), and mechanical performance (cyclic fatigue, torsional resistance, cutting ability, bending and buckling resistance). Computational fluid dynamics assessment was also conducted to determine the irrigation flow pattern, apical pressure, and wall shear stress in simulated canal preparations. Kruskal-Wallis and one-way anova post hoc Tukey tests were used for statistical comparisons (α = 5%). RESULTS: Instruments presented variations in blade numbers, helical angles, and tip designs, with all featuring non-active tips, symmetrical blades, and equiatomic nickel-titanium ratios. Cross-sectional designs exhibited an S-shaped geometry, except for WaveOne Gold. Univy 25/.04 and Reciproc Blue displayed the smallest and largest core diameters at D3. Univy 25/.04 and E-Flex Rec 25/.04 demonstrated the longest time to fracture (p < .05). Reciproc Blue and Univy 25/.04 exhibited the highest and lowest torque to fracture, respectively (p < .05). Univy 25/.04 and Reciproc Blue had the highest rotation angles, whilst E-Flex Rec 25/.06 showed the lowest angle (p < .05). The better cutting ability was observed with E-Flex Rec 25/.06, Procodile, Excalibur, and Reciproc Blue (p > .05). Reciproc R25 and E-Flex Rec showed the highest buckling resistance values (p < .05), with WaveOne Gold being the least flexible instrument. The impact of instruments' size and taper on wall shear stress and apical pressure did not follow a distinct pattern, although Univy 25/.04 and E-Flex Rec 25/.06 yielded the highest and lowest values for both parameters, respectively. CONCLUSIONS: Low-tapered reciprocating instruments exhibit increased flexibility, higher time to fracture, and greater angles of rotation, coupled with reduced maximum bending loads and buckling strength compared to large-tapered instruments. Nevertheless, low-tapered systems also exhibit lower maximum torque to fracture and inferior cutting ability, contributing to a narrower apical canal enlargement that may compromise the penetration of irrigants in that region.

Diagnostic value of cone beam computed tomography for root canal morphology assessment - a micro-CT based comparison.

OBJECTIVES: The aim of this study was to assess cone beam computed tomography (CBCT) as a root canal anatomy diagnostic tool by comparison with micro-CT gold-standard. MATERIALS AND METHODS: 216 two-rooted mandibular molars were first scanned in a CBCT device (200 µm voxel size) and posteriorly in a micro-CT scanner (19.61 µm). The volumes were sequentially screened to classify main root canal anatomy according to Vertucci classification, and for the presence of lateral canals and apical deltas, in both mesial and distal roots. RESULTS: Both methods revealed a higher prevalence of Vertucci Type II and IV in the mesial root, and Vertucci Type I in the distal root. The percentage of agreement for main root canal anatomy classification between CBCT and micro-CT scores was high (85.2%). CONCLUSION: Sensibility to detect both lateral canals and apical deltas with CBCT was low. These results attest to the fact that minor anatomical changes might be difficult to identify with CBCT imaging, hampering its diagnostic value.

Site selection for nature-based solutions for stormwater management in urban areas: An approach combining GIS and multi-criteria analysis.

In recent years, particularly following the definition of the UN Sustainable Development Goals (SDGs) for 2030, Nature-Based Solutions (NBS) have gained considerable attention, capturing the interest of both the scientific community and policymakers committed to addressing urban environmental issues. However, the need for studies to guide decision-makers in identifying suitable locations for NBS implementation within urban stormwater management is evident. To address this gap, the present study employs a methodological approach grounded in multi-criteria analysis integrated with Geographic Information Systems (GIS) to identify areas with potential for NBS implementation. In this process, ten NBS were proposed and tested in the drainage area of a shallow tropical urban lake in Londrina, southern Brazil. Additionally, the study investigates areas hosting lower-income populations, a relevant aspect for public managers given the diverse economic subsidies required to implement NBS. Furthermore, the study incorporates a preliminary analysis that evaluates the potential ecosystem benefits to determine the most suitable NBS for a specific site. The result shows that all the ten analyzed NBS were deemed suitable for the study area. Rain barrels had the highest percentage coverage in the study area (37.1%), followed by tree pits (27.9%), and rain gardens (25.4%). Despite having the highest distribution in the basin area, rain barrels exhibited only moderate ecosystem benefits, prompting the prioritization of other NBS with more significant ecological advantages in the final integrated map. In summary, the methodology proposed showed to be a robust approach to selecting optimal solutions in densely populated urban areas.

Patients with AUD exhibit dampened heart rate variability during sleep as compared to social drinkers.

Chronic heavy alcohol use profoundly affects the cardiovascular system, contributing to several life-threatening cardiovascular diseases. Heart rate variability (HRV), or the fluctuations in heart rate, reflects dynamic autonomic nervous system processes that change to meet biological demands and environmental challenges. In the current study, we examined whether HRV metrics are altered in alcohol use disorder (AUD) during waking and sleeping with passive biomonitoring as participants went about their daily lives. Social drinkers (standard deviation: n = 10, 5 female) and treatment-seeking individuals with moderate to severe AUD (n = 16, 7 female) provided continuous, real-world heart rate monitoring for 5 days of monitoring on average (M = 5.27 ± 2.22). Five indices of respiration and HRV-respiratory sinus arrhythmia (RSA) amplitude, high frequency (HF), low frequency (LF), HF/LF ratio, root-mean-square standard deviation (RMSSD), and standard deviation of the N-N intervals (SDNN)-were analyzed separately for waking and sleeping hours. Both RMSSD and SDNN decreased the longer the participants were awake (Ps < .013). During sleeping hours, HF, RSA amplitude, RMSSD, and SDNN were significantly higher in light social drinkers as compared to patients with AUD (all Ps < .009), indicating higher parasympathetic activation during sleep in the SD versus AUD group. Sleep and waking HRV measures were significantly correlated with patient-reported symptoms of depression and sleep difficulties in the AUD group (Ps < .05). This natural observational study utilizing continuous autonomic biomonitoring in the real world indicates parasympathetic dysfunction that is clearly detectable during sleep in AUD and HRV measures, which are also related to clinical, patient-related symptoms of AUD.

Comparative analysis of reciprocating and flat-side heat-treated rotary single-file systems: Design, metallurgical characteristics, and mechanical performance.

AIM: To compare two flat-side single-file rotary instruments with three single-file reciprocating systems through a multimethod assessment. METHODOLOGY: A total of 290 new NiTi single-file rotary (AF F One Blue 25/0.06 and Platinum V.EU 25/0.06) and reciprocating (One Files Blue R25, Reciproc Blue R25, Reciproc R25) instruments were selected, carefully examined for any major deformations, and evaluated regarding their macroscopic and microscopic design, nickel and titanium elements ratio, phase transformation temperatures, and mechanical performance (time/rotation to fracture, maximum torque, angle of rotation, microhardness, maximum bending, and buckling strengths). One-way anova post hoc Tukey, T-test, and nonparametric Mood's median tests were used for statistical comparisons (α = 5%). RESULTS: Tested instruments had identical blade counts and near-identical helical angles of approximately 24° (rotary instruments) and 151° (reciprocating instruments). The flat-side analysis revealed a few inconsistencies, such as discontinuity segments, different orientations, and gaps in the homogeneity of the bluish colour. Microscopically, flat-side instruments exhibited blade discontinuity and an incomplete S-shaped cross-section. The surface finish was smoother for One Files Blue and more irregular for both rotary instruments. There were distinct phase transformation temperatures amongst all instruments. All heat-treated instruments were in R-phase arrangement, and Reciproc was in R-phase plus austenite at test temperature (20°C). Compared with the reciprocating instruments, both flat-side instruments exhibited lower results in the cyclic fatigue tests using two different clockwise kinematics, maximum torque, angle of rotation, and maximum buckling strength (p < .05). The rotary systems also exhibited low flexibility (p < .05). AF F One Blue had the lowest microhardness, whilst Reciproc had the highest value. CONCLUSION: This multimethod investigation revealed that the flat-side rotary instruments underperformed the reciprocating instruments regarding cyclic fatigue (with two different clockwise kinematics), maximum torque, angle of rotation, maximum buckling strength, and flexibility. Manufacturing inconsistencies were also observed in some of the flat-side instruments, including discontinuity segments, different orientations, and in the homogeneity of their bluish colour given by the heat treatment.

To flat or not to flat? Exploring the impact of flat-side design on rotary instruments using a comprehensive multimethod investigation.

AIM: To assess the influence of a flat-side design on the geometry, metallurgy, mechanical performance and shaping ability of a novel nickel-titanium rotary instrument. METHODOLOGY: Sixty-five new 25-mm flat-side rotary instruments (size 25, taper 0.04) and their nonflat-side prototypes (n = 65) were assessed for major deformations and examined regarding macroscopic and microscopic design, determination of nickel and titanium elements ratio, measurement of phase transformation temperature and evaluation of mechanical performance parameters including time/cycles to fracture, maximum torque, angle of rotation, maximum bending and buckling strengths and cutting ability. Additionally, unprepared canal areas, volume of hard tissue debris and percentage reduction of dentine thickness were calculated for each tested instrument after preparing mesial canals of mandibular molars (n = 12), using micro-CT imaging. Statistical analyses were performed using the U-Mann-Whitney test and independent Student t-test (α = 5%). RESULTS: The number of spirals (n = 8) and blade direction (clockwise) were similar between both flat and nonflat instruments, whilst the helical angles were equivalent (⁓25°). Flat-instruments showed inconsistencies in the homogeneity of the gold colour on the flat-side surface, blade discontinuity, and incomplete and variable S-shaped cross-sections. The titanium-to-nickel ratios were equivalent, but significant differences in the R-phase finish and austenitic start phase transformation temperatures were observed between the flat and nonflat-side instruments. The flat-side instruments demonstrated superior cutting ability compared to the nonflat instruments, as well as, significantly lower values for time to fracture, rotation to fracture and maximum torque to fracture (p < .001). No statistical difference was observed between tested instruments regarding angle of rotation (p = .437), maximum bending (p = .152) and buckling load (p = .411). Preparation protocols using flat and nonflat instruments did not show any statistically significant differences (p > .05). All flat-side instruments exhibited deformation after shaping procedures. CONCLUSIONS: The flat-side instrument showcased enhanced cutting ability compared to its nonflat counterpart. However, it exhibited inferior performance in terms of time, rotation and maximum torque to fracture, along with distinct phase transformation temperatures. No differences were observed in the titanium-to-nickel ratios, angle of rotation, maximum bending, buckling load, preparation time, percentage of untouched canal walls, volume of hard tissue debris and percentage reduction of dentine thickness.

Characterization of the file-specific heat-treated ProTaper Ultimate rotary system.

AIM: To compare design, metallurgy and mechanical performance of the ProTaper (PT) Ultimate system with instruments of similar dimensions from the ProGlider, PT Gold and PT Universal systems. METHODOLOGY: New PT Ultimate instruments (n = 248) were compared with instruments of similar dimensions from ProGlider (n = 31), PT Gold (n = 155) and PT Universal (n = 155) systems regarding their number of spirals, helical angle, blade symmetry, tip geometry, surface finishing, nickel/titanium ratio, phase transformation temperatures and mechanical performance. One-way anova and nonparametric Mood's median tests were used for statistical comparison (α = 5%). RESULTS: All instruments had symmetrical blades without radial lands or flat sides, similar surface finishing and an almost equiatomic nickel/titanium ratio, whilst the number of spirals, helical angles and the tip geometry were different. PT Ultimate instruments showed 3 distinct heat treatments that matched with the colour of their metal wire. Slider and ProGlider instruments had similar R-phase start (Rs) and R-phase finish (Rf) temperatures. SX, F1, F2, F3 and Shaper instruments showed equivalent heat treatments (Rs ~45.6°C and Rf ~28.3°C) that were similar to their PT Gold counterparts (Rs ~47.9°C and Rf ~28.2°C), but completely distinct to the PT Universal ones (Rs ~16.2°C and Rf ~-18.2°C). Amongst the PT Ultimate instruments, the lowest maximum torques were observed in the SX (0.44 N cm), Slider (0.45 N cm) and Shaper (0.60 N cm) instruments, whilst the highest was noted in the FXL (4.90 N cm). PT Ultimate Slider and ProGlider had similar torsional (~0.40 N cm) and bending loads (~145.0 gf) (p = 1.000), whilst the other PT Ultimate instruments showed statistically significantly lower maximum torque, higher angle of rotation and lower bending load (higher flexibility) than their counterparts of the PT Universal and PT Gold systems. CONCLUSIONS: The PT Ultimate system comprises instruments with 3 distinct heat treatments that showed similar phase transformation temperatures to their heat-treated analogues. PT Ultimate instruments presented lower torsional strength and superior flexibility than their counterparts, whilst maximum torque, angle of rotation and bending loads progressively increased with their sizes.

Characterization of four heat-treated reciprocating instruments: Design, metallurgy, mechanical performance, and irrigation flow patterns.

AIM: To compare the design, metallurgy, and mechanical properties of four heat-treated reciprocating instruments coupled with the evaluation of the irrigation flow using an in silico model. METHODOLOGY: New EdgeOne Fire Primary, Easy-File Flex Regular 25, WaveOne Gold Primary and Reciproc Blue R25 instruments (n = 124) were initially evaluated regarding their design through stereomicroscopy, scanning electron microscopy and 3D surface scanning. In addition, energy-dispersive X-ray spectroscopy was utilized to determine their elemental composition, and differential scanning calorimetry tests to evaluate their phase transformation temperatures. Their mechanical performance was further assessed through torsional and bending tests. Using scans obtained from a real tooth and the instruments, a computational fluid dynamics assessment was conducted to determine the irrigation flow pattern, apical pressure, and wall shear stress in simulated canal preparation. Mood's median and One-way anova post hoc Tukey tests were used for statistical comparisons (α = 5%). RESULTS: Reciproc Blue exhibited a superior number of blades (n = 8), whereas EdgeOne Fire had the highest overall volume (4.38 mm3 ) and surface area (32.32 mm2 ). At the 3-mm axial level, EdgeOne Fire displayed the lowest core diameter (0.13 mm), while Reciproc Blue had the highest (0.16 mm). All blades were symmetrical, and the tips of the instruments were non-active but differed from each other. The most irregular surfaces were observed in EdgeOne Fire and Easy-File Flex. All instruments were manufactured from nickel-titanium alloys and exhibited distinct phase transformation temperatures. WaveOne Gold and Reciproc Blue demonstrated the highest maximum torque values (1.87 and 1.62 N cm, respectively), while the lowest was observed on EdgeOne Fire (1.21 N cm) (p < .05). The most flexible (p < .05) were EdgeOne Fire (angle of rotation: 602.6°; maximum bending load: 251.4 g.f) and Reciproc Blue (533.2° and 235.6 g.f). There were no significant differences observed in the irrigation flow among the four domains generated by the tested instruments. CONCLUSIONS: Despite observing variations in the design, phase transformation temperatures, and in the torsional and bending test outcomes among the four heat-treated reciprocating instruments, no significant differences were found in the irrigation flow pattern among the different groups in the simulated root canal preparations.

Multimethod analysis of three rotary instruments produced by electric discharge machining technology.

AIM: This study aimed to compare three rotary instruments produced by the EDM process with the heat-treated ProTaper Gold system regarding design, metallurgy, mechanical properties and shaping ability. METHODOLOGY: HyFlex EDM (25/~), Neoniti (25/.06), EDMax (25/.06) and ProTaper Gold (25/.08v) instruments (n = 58 per group) were compared regarding design, metallurgy and mechanical performance. Unprepared canal areas were calculated for each system after preparation of mesiobuccal, mesiolingual and distal canals of mandibular molars (15 canals per group) using micro-CT technology. Statistical analyses were performed using One-way anova post-hoc Tukey and Kruskal-Wallis post-hoc Dunn's tests (α = 5%). RESULTS: All instruments had asymmetrical blades, no radial lands, no major defects and almost equiatomic nickel/titanium ratios, but different cross-section designs, tip geometries and surface appearances. Although instruments had distinct transformation temperature curves, they showed crystallographic martensitic arrangement at 21°C and mixed austenite plus R-phase at body temperature. Neoniti and HyFlex EDM showed similar results in all mechanical tests (p > .05), while EDMax and ProTaper Gold had similar time to fracture (p = .841), maximum bending load (p = .729), and cutting ability (p = .985). ProTaper Gold showed the highest torque to failure (p < .001) and HyFlex EDM had the lowest buckling resistance (p < .001). Mean percentages of unprepared canal areas ranged from 20.4% to 25.7% in the mesial canals, and from 20.8% to 26.2% in the distal canal, with no statistical differences among systems (p > .05). CONCLUSIONS: Instruments' geometry and phase transformation temperatures influenced the results of the mechanical tests, but not their shaping ability.

Metabolomic profile of seminal plasma from Guzerá bulls (Bos indicus) with contrasting sperm freezability phenotypes.

The present study evaluated the seminal plasma metabolome of Bos indicus Guzerá bulls with good (n = 4) and poor (n = 5) sperm freezability. Animals were raised in natural pasture of a 'Caatinga' ecosystem, in the semi-arid region of Brazil. Seminal plasma samples were subjected to gas chromatography coupled to mass spectrometry and data, analysed using bioinformatics tools (Cytoscape with the MetScape plug-in). Sixty-two metabolites were identified in the bovine seminal plasma. Fatty acids and conjugates and organic compounds were the predominant seminal fluid metabolites, followed by carboxylic acids and derivatives, amino acids, benzenes and steroids and derivatives, carbohydrates and carbohydrate conjugates and prenol lipids. Multivariate analysis indicated a distinct separation of seminal plasma metabolomes from bulls with contrasting sperm freezability. Abundances of propanoic acid, d-ribose and glycine were greater in the seminal plasma of bulls with good sperm freezability. Heptadecanoic acid and undecanoic acid were the predominant in bulls of poor sperm freezability. Propanoic acid is an energy source for spermatozoa and may act as an antimicrobial component in semen. Glycine acts against oxidizing and denaturing reactions. d-ribose is also an energy source and reduces apoptosis and oxidative stress. Undecanoic acid may protect sperm against fungal damage. This study provides fundamental information approximately the seminal plasma metabolome of tropically adapted bulls and its association with sperm freezability. However, further studies with larger groups of animals are needed to validate those metabolites as markers of sperm freezability. This strategy could support the selection of sires with superior sperm cryoresistance.

Age-related changes in the morphology of the root canal system of mandibular first molars: a micro-CT study.

OBJECTIVE: This study aimed to evaluate changes on root canal morphology in patients with different ages using micro-CT technology. MATERIALS AND METHODS: Mandibular first molars (n = 150) were scanned at a pixel size of 13.68 µm, categorized into 3 groups according to patient's age and analyzed regarding configuration, orifices, apical foramina, root length, canal volume, and surface area. Morphological 2D and 3D parameters were evaluated in distal roots with Type I configuration (n = 109) as well as the morphology of isthmuses Types I and III in 68 mesial roots. One-way ANOVA post hoc Tukey and Kruskal-Wallis tests were used for statistical analyses (α = 5%). RESULTS: A great variation in the canal configuration was found. No difference was observed in roots' length (p > 0.05). Canal volume reduced with age (p < 0.05), while surface area increased (p < 0.05) in patients ≤ 30 years. There was no difference in canal/root length, area, and from foramen to the apex in distal roots with Type I configuration (p > 0.05), but 2D and 3D parameters significantly decreased with age (p < 0.05). Overall, the diameter of the isthmuses' roof reduced with age (p < 0.05). In patients ≥ 31 years with Type III isthmus the distance from the isthmus floor to the foramen of the mesiolingual canal also decreased (p < 0.05). CONCLUSION: Overall, the internal morphology of the mesial roots of mandibular first molars was more affected by aging than distal canals. The most relevant tested parameter that significantly reduced in both roots was the volume of the root canal systems. CLINICAL RELEVANCE: A detailed evaluation of fine anatomical aspects of the root canal system of mandibular first molars of patients with different ages showed that the internal morphology of mesial roots is more affected by aging than distal canals.

Design, metallurgy, mechanical properties, and shaping ability of 3 heat-treated reciprocating systems: a multimethod investigation.

OBJECTIVE: This study aimed to compare 3 reciprocating systems regarding design, metallurgy, mechanical properties, and shaping ability. MATERIALS AND METHODS: New Reciproc Blue R25, WaveOne Gold Primary, and REX 25 instruments (n=41 per group) were analyzed regarding design, metallurgy, and mechanical performance, while shaping ability (untouched canal walls, volume of removed dentin, and hard tissue debris) was tested in 36 anatomically matched root canals of mandibular molars. Results were compared using one-way ANOVA post hoc Tukey and Kruskal-Wallis tests with a significant level set at 5%. RESULTS: All instruments showed symmetrical cross sections with asymmetrical blades, no radial lands, no major defects, and an almost equiatomic nickel and titanium ratio. The highest R-phase start temperatures were observed with WaveOne Gold (46.1°C) and REX (44.8°C), while Reciproc Blue had the lowest R-phase start (34.5°C) and finish (20°C) temperatures. WaveOne Gold had the lowest time to fracture (169 s) and the highest maximum load (301.6 gf) (P <0.05). The maximum torque of Reciproc Blue (2.2 N.cm) and WaveOne Gold (2.1 N.cm) were similar (P >0.05), but lower than REX (2.6 N.cm) (P <0.05). No statistical differences were observed among instruments in the angle of rotation (P >0.05) and in the shaping ability in both mesial and distal canals (P >0.05). CONCLUSION: Although the overall design, temperature transition phases and mechanical behavior parameters were different among tested instruments, they were similar in terms of shaping ability. CLINICAL RELEVANCE: All tested heat-treated NiTi reciprocating systems showed similar shaping ability, without clinically significant errors.

Long-term management practices successfully reduce bird-related electrical faults in a transmission grid increasingly used by white storks for nesting.

Bird nests on transmission lines can cause electrical faults which reduce service reliability. To address this problem, since the mid-90s, the Portuguese Transmission System Operator (TSO) has undertaken management actions to discourage white storks Ciconia ciconia from nesting in hazardous locations of the pylons. Here, we compiled and analyzed an 18-year series of data on electrical faults, TSO management actions to tackle these, and stork nests on transmission pylons in Portugal to: (a) determine the relative importance of bird-related faults over the total number of faults; (b) describe variations in bird-related faults across time (season of the year and time of the day); (c) describe spatial variations in bird-related faults and their association with the occurrence of white stork nests on pylons; and (d) analyze the trends, over the years, of the number of white stork nests on pylons, the TSO management actions and their effectiveness in reducing bird-related fault rates. Overall, birds accounted, on average, for 25.3% of the electrical faults in the transmission network, with the vast majority being attributed to white storks. The seasonal pattern of bird-related faults showed higher rates in April and in October-November. Faults occurred more often during the night period, when storks spend more time on the pylons. We found a positive spatial relationship between the electrical fault rate and the proportion of pylons with stork nests (and the correlated number of nests per 100 km of line). There was, however, considerable variation in the fault rates not explained by the stork nest variables, particularly during the non-breeding season. The TSO management actions (namely removal/translocation of nests in hazardous locations of the pylons, installation of anti-perching devices and provision of alternative nesting platforms) significantly reduced, as a whole, the annual number of bird-related faults between 2001 and 2018, despite the three-fold increase in the number of white stork nests on transmission pylons. A deeper understanding of how white storks use the transmission pylons outside the breeding season is needed, so that targeted management actions can be taken to reduce the remaining bird-related fault rates to residual levels.

Irregular Autonomic Modulation Predicts Risky Drinking and Altered Ventromedial Prefrontal Cortex Response to Stress in Alcohol Use Disorder.

AIMS: Autonomic dysfunction has been associated with risky drinking and alcohol use disorder (AUD). Although autonomic nervous system (ANS) activity has been attributed to the ventromedial prefrontal cortex (VmPFC)-limbic-striatal regions, the specific role of ANS disruption in AUD and its association with these regions remain unclear. Using functional magnetic resonance imaging (fMRI) and concurrent electrocardiogram (ECG), the current study examined neural correlates of ANS activity in AUD and its role in AUD pathology. METHODS: Demographically matched 20 AUD patients and 20 social drinkers (SD) completed an fMRI task involving repeated exposure to stress, alcohol-cue and neutral-relaxing images in a block design. Based on the known VmPFC-limbic-striatal functions involved in emotions, reward and the ANS, we performed a regions of interest (ROI) analysis to examine the associations between ANS activity and neural responses in the VmPFC, amygdala, and ventral striatum. RESULTS: Across conditions, AUD patients showed significantly higher levels of overall heart rate (HR) and approximate entropy (ApEn) compared to SD (Ps < 0.05). In all participants, increased HR was associated with greater drinking volume (P < 0.05). In addition, higher ApEn levels were associated with greater drinking volume (P < 0.05) and decreased right VmPFC response to stress (P < 0.05). DISCUSSION: Our findings demonstrate ANS disruption in AUD indexed by high overall HR and ApEn. The association between ApEn and rVmPFC response suggests that ApEn may play a role in modulating drinking via interactions with neural regions of emotion regulation. These findings provide insight into patterns of ANS disruption and their relevance to AUD pathology.

Differential brain responses to alcohol-related and natural rewards are associated with alcohol use and problems: Evidence for reward dysregulation.

Multiple theoretical perspectives posit that drug use leads to biased valuation of drug-related reward, at the expense of naturally occurring rewarding activities (i.e., reward dysregulation). Recent research suggests that the comparative balance of drug-related and nondrug-related reward valuation is a powerful determinant of substance misuse and addiction. We examined differential neurophysiological responses-indexed with the P3 component of the event-related potential (ERP)-elicited by visual alcohol cues and cues depicting natural reward as a neurobiological indicator of problematic drinking. Nondependent, young adult drinkers (N = 143, aged 18-30 years) completed questionnaire measures assessing alcohol use and problems, and viewed alcohol cues (pictures of alcoholic beverages), high-arousing natural reward cues (erotica, adventure scenes), nonalcoholic beverage cues, and neutral scenes (e.g., household items) while ERPs were recorded. When examined separately, associations of P3-ERP reactivity to alcohol cues and natural reward cues with alcohol use and problems were weak. However, differential P3 response to the two types of cues (i.e., reward dysregulation P3) showed consistent and robust associations with all indices of alcohol use and problems and differentiated high-risk from lower-risk drinkers. The current results support the idea that the differential incentive-motivational value of alcohol, relative to naturally rewarding activities, is associated with increased risk for substance misuse and dependence, and highlight a novel neurophysiological indicator-the reward dysregulation P3-of this differential reward valuation.

Prevalence of periapical lesions, root canal treatments and restorations in teeth adjacent to implant- or tooth-supported crowns: A multi-centre cross-sectional study.

AIM: To describe the prevalence of periapical lesions, root canal treatments and coronal restorations on teeth adjacent to either implant- or natural tooth-supported crowns using cone-beam computed tomography (CBCT) assessment compared to nonadjacent teeth. METHODOLOGY: A total of 1249 CBCT volumes were screened by five pre-calibrated observers in 11 health centres. A step-by-step screening protocol was implemented and reviewed every 3 months, and mandatory setting characteristics were established for all CBCT scans using dedicated visualization software. Intra- and inter-rater reliability tests were conducted. The prevalence of periapical lesions, root canal treatments and coronal restorations was recorded on both teeth adjacent and nonadjacent to implant- (predictor 1) or natural tooth-supported crowns (predictor 2). A binary logistic model (Generalizing Estimating Equations test) was used to verify whether the prevalence of periapical lesion, root canal filling and the tooth restorative status are altered when the assessed tooth is adjacent or not to an implant-supported crown (predictor 1); or to a natural tooth-supported crown (predictor 2). Odds ratio and confidence intervals for the dependent variables at both predictors were obtained. The significance level was set at .05. RESULTS: A global sample of 22 899 teeth was included. Compared to nonadjacent teeth, the prevalence of periapical lesion, root canals treatments and restorative procedures when adjacent to implant-supported crowns was 10.7%, 19.6% and 22.9% higher, respectively, and when adjacent to tooth-supported crowns was 19.3%, 35.6% and 37.4% higher respectively. These results were significant only for variables root canal filling and coronal restoration (p < .0001). Odds ratio to present root canal treatment is 2.57 times higher (CI 1.95-3.39, p = .0001) when the tooth is adjacent to implant-supported crown and 4.39 times (CI 3.49-5.53, p = .0001) when adjacent to tooth-supported crown, whilst for restorative procedure, the odds are, respectively, 1.63 (CI 1.29-2.06, p = .0001) and 2.30 (CI 1.92-2.76, p = .0001). CONCLUSIONS: Teeth adjacent to both implant- and natural tooth-supported crowns were associated with a higher frequency of root canal filling and coronal restorations.

Experimental validation of a computational fluid dynamics model using micro-particle image velocimetry of the irrigation flow in confluent canals.

AIM: This study aimed to experimentally validate a computational fluid dynamics (CFD) model, using micro-particle image velocimetry (micro-PIV) measurements of the irrigation flow velocity field developed in confluent canals during irrigation with a side-vented needle. METHODOLOGY: A microchip with confluent canals, manufactured in polydimethylsiloxane was used in a micro-PIV analysis of the irrigation flow using a side-vented needle placed 3 mm from the end of the confluence of the canals. Velocity fields and profiles were recorded for flow rates of 0.017 and 0.1 ml/s and compared with those predicted in CFD numerical simulations (using a finite volume commercial code - FLUENT) for both laminar and turbulent regimes. RESULTS: The overall flow pattern, isovelocity and vector maps as well as velocity profiles showed a close agreement between the micro-PIV experimental and CFD predicted data. No relevant differences were observed between the results obtained with the laminar and turbulent flow models used. CONCLUSIONS: Results showed that the laminar CFD modelling is reliable to predict the flow in similar domains.

Effects of root canal enlargement on unprepared areas and coronal dentine thickness of three-rooted maxillary first premolars with different root configurations: A stepwise micro-CT study.

AIM: To evaluate the effects of progressive root canal enlargements on the unprepared surface area and remaining dentine thickness of three-rooted maxillary first premolars with different root configurations. METHODOLOGY: Thirty three-rooted maxillary first premolars with three root configurations (n = 10) were selected and scanned in a micro-CT device. The root canals were sequentially enlarged with rotary instruments sizes 30.02 (step 1), 30.04 (step 2) and 30.06 (step 3). After each step, a new scan was taken. Analysed parameters included morphometric measurements (length, volume and surface area), number of static voxels and minimal dentine thickness. Statistical analyses were performed with one-way anova post hoc Tukey tests and paired sample t-test at a significance level of 5%. RESULTS: No statistical differences were observed amongst groups regarding the morphometric parameters and static voxels (p > .05). The minimal dentine thickness of the distobuccal root significantly changed depending on the root configuration (p < .05), whilst no differences were observed in the other roots (p > .05). A great variation in the position of the minimal dentine thickness was observed after preparation. Overall, mean percentage reduction in dentine thickness was higher in the buccal roots than in the palatal root (p < .05). In the mesiobuccal and distobuccal root, the number of slices with minimal dentine thickness lower than 0.05 mm increases 2 to 3 times and 3 to 4 times, respectively, from steps 1 to 3. CONCLUSIONS: Instruments sizes 30.02 and 30.04 can be safely and effectively used to enlarge the buccal and palatal canals of three-rooted maxillary first premolars.

Comparison of five rotary systems regarding design, metallurgy, mechanical performance, and canal preparation-a multimethod research.

OBJECTIVES: To compare the design, metallurgy, mechanical performance, and canal preparation of 5 rotary systems. MATERIAL AND METHODS: A total of 735 25-mm NiTi instruments (sizes 0.17[0.18]/.02v, 0.20/.04v, 0.20/.07v, 0.25/.08v, 0.30/.09v) from ProTaper Gold, ProTaper Universal, Premium Taper Gold, Go-Taper Flex, and U-File systems were compared regarding overall geometry and surface finishing (stereomicroscopy and scanning electron microscopy), nickel and titanium ratio (energy-dispersive spectroscopy), phase transformation temperatures (differential scanning calorimetry), mechanical performance (torsional and bending tests), and unprepared canal surface (micro-CT). One-way ANOVA and Mood's median tests were used for statistical comparisons with a significance level set at 5%. RESULTS: Stereomicroscopic analysis showed more spirals and high helical angles in the Premium Taper Gold system. All sets of instruments had symmetrical spirals, no radial lands, no major defects, and an almost equiatomic ratio between nickel and titanium elements, while differences were observed in their tips' geometry and surface finishing. At room temperature (20 °C), DSC test revealed martensitic characteristics for ProTaper Gold and Go-Taper Flex, and mixed austenite plus R-phase for the Premium Taper Gold, while ProTaper Universal and U-Files had full austenitic characteristics. Overall, larger instruments had higher torque resistance and bending load values than smaller ones, while a lack of consistency and mixed values were observed in the angle of rotation. The 0.25/.08v and 0.30/.09v instruments of ProTaper Universal and U-File had the highest maximum torques, the lowest angles of rotation, and the highest bending loads than other tested systems (P < .05). No significant difference was noted regarding the untouched root canal walls after preparation with the tested systems (P > .05). CONCLUSIONS: Although differences observed in the overall geometry and phase transformation temperatures have influenced the results of mechanical tests, unprepared canal surface areas were equivalent among systems. CLINICAL RELEVANCE: Root canal preparation systems with similar geometries might present different mechanical behaviors but equivalent shaping ability.

Analysis of the Equilibrium Distribution of Ligands in Heterogeneous Media-Approaches and Pitfalls.

The equilibrium distribution of small molecules (ligands) between binding agents in heterogeneous media is an important property that determines their activity. Heterogeneous systems containing proteins and lipid membranes are particularly relevant due to their prevalence in biological systems, and their importance to ligand distribution, which, in turn, is crucial to ligand's availability and biological activity. In this work, we review several approaches and formalisms for the analysis of the equilibrium distribution of ligands in the presence of proteins, lipid membranes, or both. Special attention is given to common pitfalls in the analysis, with the establishment of the validity limits for the distinct approaches. Due to its widespread use, special attention is given to the characterization of ligand binding through the analysis of Stern-Volmer plots of protein fluorescence quenching. Systems of increasing complexity are considered, from proteins with single to multiple binding sites, from ligands interacting with proteins only to biomembranes containing lipid bilayers and membrane proteins. A new formalism is proposed, in which ligand binding is treated as a partition process, while considering the saturation of protein binding sites. This formalism is particularly useful for the characterization of interaction with membrane proteins.