Antibacterial and Photodegradative Properties of Metal Doped TiO2 thin Films Under Visible Light.

Doped (Au, Ag) and undoped TiO2 thin films were prepared on soda-lime glass via the sol-gel method by dip-coating from TiCl4 precursor, followed by 30 minutes calcination at 500 °C to obtain transparent thin films with good adhesion to the substrate. XRD analysis showed that the particle size of samples heat treated at 500 °C was ~10 nm for all of the samples prepared, both doped and undoped ones. SEM images revealed that the thin film surface was homogeneous and nano-porous. The hydrophilicity of the thin films was estimated by contact angle measurements. The photodegradation rate of an aqueous solution of the azo dye Plasmocorinth B on the thin films was tested by in-situ UV-Vis spectroscopic measurements of the dye solution. The best photocatalytic activity under visible and UVA light was exhibited by undoped TiO2 thin films, whereas Au doped thin films were slightly less active. On the other hand, the best antimicrobial activity toward the E. coli strain DH5a under visible light was displayed by the Au/TiO2 thin films.

Metal and Non-Metal Modified Titania: the Effect of Phase Composition and Surface Area on Photocatalytic Activity.

The application of TiO2 photocatalysis in various environmental fields has been extensively studied in the last decades due to its ability to induce the degradation of adsorbed organic pollutants. In the present work, TiO2 powders doped and co-doped with sulfur and nitrogen and modified with platinum were prepared by particulate sol-gel synthesis. PXRD measurements revealed that the replacement of HCl with H2SO4 during synthesis reduced the size of the crystallites from ~ 30 nm to ~20 nm, increasing the surface area from ~44 m2/g to ~80 m2/g. This is consistent with the photocatalytic activity of the samples and the measured photocurrent behavior of the photocatalysts. The results showed that the properties of the powders (i.e., surface area, crystallite size, photocurrent behavior) depend strongly not only on the type but also on the amount of acid and dopants used in the synthesis. Doping, co-doping and modification of TiO2 samples with nitrogen, sulfur and platinum increased their photocatalytic activity up to 6 times.

Controlled growth of ZnO nanoparticles using ethanolic root extract of Japanese knotweed: photocatalytic and antimicrobial properties.

Synthesis of zinc oxide (ZnO) nanoparticles (NPs) was mediated by plant extracts to assist in the reduction of zinc atoms during the synthesis and act as a capping agent during annealing. The preparation used ethanolic extracts from the roots of Japanese knotweed (Fallopia japonica). Two major outcomes could be made. (i) A synergistic effect of multiple polyphenolic components in the extract is needed to achieve the capping effect of crystallite growth during thermal annealing at 450 °C characterized by an exponential growth factor (n) of 4.4 compared to n = 3 for bare ZnO. (ii) Synergism between the ZnO NPs and plant extracts resulted in superior antimicrobial activity against both Gram-positive bacteria, e.g., Staphylococcus aureus, and Gram-negative bacteria, e.g., Escherichia coli and Campylobacter jejuni. The materials were also tested for their antimicrobial activity against S. aureus under ultraviolet (UV) illumination. Also here, the photocatalyst prepared with plant extracts was found to be superior. The residues of the plant extract molecules on the surface of the catalyst were identified as the main cause of the observed differences, as proved by thermal gravimetry. Such a preparation using ethanolic extract of Fallopia japonica could serve as a more controlled synthesis of ZnO and potentially other metal oxides, with low environmental impact and high abundance in nature.

One-Pot Synthesis of Sulfur-Doped TiO2/Reduced Graphene Oxide Composite (S-TiO2/rGO) With Improved Photocatalytic Activity for the Removal of Diclofenac From Water.

Sulfur-doped TiO2 (S-TiO2) composites with reduced graphene oxide (rGO), wt. % of rGO equal to 0.5%, 2.75%, and 5.0%, were prepared by a one-pot solvothermal procedure. The aim was to improve photocatalytic performance in comparison to TiO2 under simulated solar irradiation for the treatment of diclofenac (DCF) in aqueous medium. The obtained composites were characterized for physical-chemical properties using thermogravimetric analysis (TGA), X-ray diffractograms (XRD), Raman, scanning electron microscopy (SEM)/energy dispersive X-ray (EDX), Brauner Emmett Teller (BET), and photoluminescence (PL) analyses, indicating successful sulfur doping and inclusion of rGO. Sulfur doping and rGO have successfully led to a decrease in photogenerated charge recombination. However, both antagonistic and synergistic effects toward DCF treatment were observed, with the latter being brought forward by higher wt.% rGO. The composite with 5.0 wt.% rGO has shown the highest DCF conversion at pH 4 compared to that obtained by pristine TiO2, despite lower DCF adsorption during the initial dark period. The expected positive effects of both sulfur doping and rGO on charge recombination were found to be limited because of the subpar interphase contact with the composite and incomplete reduction of the GO precursor. Consequent unfavorable interactions between rGO and DCF negatively influenced the activity of the studied S-TiO2/rGO photocatalyst under simulated solar irradiation.

Design and evaluation of a compact photocatalytic reactor for water treatment.

A compact reactor for photocatalytic oxidation and photocatalytic ozonation water treatment was developed and evaluated by using four model pollutants. Additionally, combinations of pollutants were evaluated. Specially produced Al2O3 porous reticulated monolith foams served as TiO2 carriers, offering a high surface area support. UV lamps were placed in the interior to achieve reduced dimensions of the reactor (12 cm in diameter × 20 cm in height). Despite its small size, the overall photocatalytic cleaning capacity was substantial. It was evaluated by measuring the degradation of LAS + PBIS and RB19 as representatives of surfactants and textile dyes, respectively. These contaminants are commonly found in household grey wastewater with phenol as a trace contaminant. Three different commercial photocatalysts and one mixture of photocatalysts (P25, P90, PC500 and P25 + PC500) were introduced in the sol-gel processing and immobilized on foamed Al2O3 monoliths. RB19 and phenol were easily degradable, while LAS and PBIS were more resistant. The experiments were conducted at neutral-acidic pH because alkaline pH negatively influences both photocatalyic ozonation (PCOZ) and photocatalysis. The synergistic effect of PCOZ was generally much more expressed in mineralization reactions. Total organic carbon TOC half lives were in the range of between 13 and 43 min in the case of individual pollutants in double-deionized water. However, for the mixed pollutants in tap water, the TOC half-life only increased to 53 min with the most efficient catalyst (P90). In comparison to photocatalysis, the PCOZ process is more suitable for treating wastewater with a high loading of organic pollutants due to its higher cleaning capacity. Therefore, PCOZ may prove more effective in industrial applications.

Sulfur-, nitrogen- and platinum-doped titania thin films with high catalytic efficiency under visible-light illumination.

Titanium dioxide photocatalysts have received a lot of attention during the past decades due to their ability to degrade various organic pollutants to CO2 and H2O, which makes them suitable for use in environmental related fields such as air and water treatment and self-cleaning surfaces. In this work, titania thin films and powders were prepared by a particulate sol-gel route, using titanium tetrachloride (TiCl4) as a precursor. Afterwards, the prepared sols were doped with nitrogen (ammonium nitrate, urea), sulfur (thiourea) and platinum (chloroplatinic acid), coated onto glass substrates by dip-coating, and thermally treated in a muffle furnace to promote crystallization. The resulting thin films were then characterized by various techniques (i.e., TGA-DSC-MS, XRD, BET, XPS, SEM, band gap measurements). The photocatalytic activity of the prepared thin films was determined by measuring the degradation rate of plasmocorinth B (PB), an organic pigment used in the textile industry, which can pose an environmental risk when expelled into wastewater. A kinetic model for adsorption and subsequent degradation was used to fit the experimental data. The results have shown an increase in photocatalytic activity under visible-light illumination of nonmetal and metal doped and co-doped titania thin films compared to an undoped sample.