Microwave-induced combustion for further determination of potentially toxic elements in honey by ICP-MS.

Microwave-induced combustion (MIC) was proposed in this study for honey decomposition aiming for As, Cd, Hg, and Pb determination by inductively coupled plasma mass spectrometry (ICP-MS). Sample mass (up to 1.0 g), absorbing solution (0.5 to 14.4 mol L-1 HNO3, and H2O), heating program, and combustion aids were evaluated. The Eurachem guidelines were used for method validation. The proposed method enabled combustion of a high sample mass (0.8 g of honey, with 0.4 g of microcrystalline cellulose and 100 µL of 6 mol L-1 NH4NO3) using 6 mL of an absorbing solution consisting of 1 mol L-1 HNO3, which resulted in low residual carbon in solution (< 25 mg L-1). Honey samples from different geographical origins were analyzed. Results showed no significant difference in comparison to other two microwave decomposition methods, based on microwave-assisted wet digestion with single reaction chamber (MAWD-SRC) and microwave-assisted wet digestion (MAWD). Standard addition experiments resulted in recoveries higher than 98%. The limits of detection ranged from 1.10 (As) to 4.60 ng g-1 (Pb). In addition to using only diluted reagents and resulting in digests virtually free of interferences, the proposed method was faster (< 30 min) than most of those presented in the literature.

Determination of halogens and sulfur in honey: a green analytical method using a single analysis.

The halogen determination is important in view of their biological and environmental roles, but their determination has still been considered a challenge, especially at low concentrations. Therefore, a method for honey decomposition using microwave-induced combustion (MIC) combined with ion chromatography and conductimetric detection (for Cl, F, and S determination) or mass detection (for Br and I determination) (IC-CD-MS) is proposed. Trueness was evaluated by adding reference materials (RMs) or a standard solution in the sample. By using 50 mmol L-1 NH4OH as the absorbing solution, recoveries for all analytes were between 94 and 103%, in both tests. Moreover, no statistical difference (t test, confidence level of 95%) was observed for the results obtained by IC in comparison with those obtained by inductively coupled plasma optical emission spectroscopy (Cl and S) and by inductively coupled plasma mass spectrometry (Br and I). Finally, the proposed method was applied to 19 honey samples from different origins. The concentrations ranged from < 0.45 to 2.39 mg kg-1 (Br), 21.8 to 671 mg kg-1 (Cl), and 11 to 154 mg kg-1 (S), while the F and I concentrations were below that their quantification limits (LOQs) in all analyzed samples. The LOQs for Br, Cl, F, I, and S were 0.45, 21, 3.7, 0.077, and 8.7 mg kg-1, respectively. The MIC method provided a compatible solution to IC for the halogen and S determination in honey by a single analysis. Graphical abstract.

Determination of elemental impurities in pharmaceutical products and related matrices by ICP-based methods: a review.

Interest in the determination of elemental impurities in pharmaceuticals has increased in recent years because of changes in regulatory requirements and the need for changing or updating the current limit tests recommended in pharmacopeias. Inductively coupled plasma (ICP) optical emission spectrometry and ICP mass spectrometry are suitable alternatives to perform multielemental analysis for this purpose. The main advantages and limitations of these techniques are described, covering the applications reported in the literature in the last 10 years mainly for active pharmaceutical ingredients, raw materials, and pharmaceutical dosage forms. Strategies used for sample preparation, including dissolution in aqueous or organic solvents, extraction, wet digestion and combustion methods are described, as well as direct solid analysis and ICP-based systems applied for speciation analysis. Interferences observed during the analysis of pharmaceutical products using ICP-based methods are discussed. Methods currently recommended by pharmacopeias for elemental impurities are also covered, showing that the use of ICP-based methods could be considered as a trend in the determination of these impurities in pharmaceuticals. However, the development of a general method that is accurate for all elemental impurities and the establishment of an official method are still challenges. In this regard, the main drawbacks and suitable alternatives are discussed.

Feasibility of ultra-trace determination of bromine and iodine in honey by ICP-MS using high sample mass in microwave-induced combustion.

This work demonstrates the feasibility of ultra-trace determination of halogens in biological samples by inductively coupled plasma mass spectrometry (ICP-MS) after decomposition by microwave-induced combustion (MIC). The conventional MIC method was improved to allow the combustion of samples with mass higher than that used in previous works in order to achieve better limits of detection (LODs). The applicability of the proposed method for ultra-trace determination of bromine and iodine in organic samples was demonstrated here using honey. It was possible to decompose up to 1000 mg of honey using microcrystalline cellulose as a combustion aid and polyethylene film for sample wrapping. After combustion, analytes were absorbed using 50 mmol L(-1) NH4OH and recoveries for Br and I were between 99 and 104 %, and relative standard deviations were lower than 5 %. Microwave-assisted alkaline dissolution (MA-AD) was also evaluated for honey sample preparation using NH4OH or tetramethylammonium hydroxide solutions. However, the LODs for the MA-AD method were unsuitable because the high carbon content in digests required a dilution step prior to the analysis by ICP-MS. The LODs obtained by MIC were improved from 1143 to 34 ng g(-1) for Br and from 571 to 6.0 ng g(-1) for I, when compared to the MA-AD method. Furthermore, it was possible to decompose up to eight samples simultaneously in 30 min (including the cooling step) with very low reagent consumption and consequently lower generation of effluents, making MIC method well suited for routine ultra-trace determination of Br and I in honey. Graphical Abstract A high mass of honey was efficiently digested by MIC for subsequent Br and I determination by ICP-MS.

Low cost sample preparation method using ultrasound for the determination of environmentally critical elements in seaweed.

In this study, ultrasound (US) was evaluated for As, Cd, Pb, Mn, Sr and V extraction from seaweed samples. The following parameters of ultrasound-assisted extraction (UAE) using an US bath were: frequency (25 to 130 kHz), amplitude (30 to 100%), temperature (30 to 80 °C), sample mass (50 to 200 mg), extractant concentration (1 to 3 mol L-1 of HNO3) and treatment time (5 to 30 min). Acoustic density and power density distribution were calculated using the calorimetric method and mapping of the acoustic pressure distribution was also evaluated. The optimized UAE conditions were 200 mg of sample in 10 mL of 2 mol L-1 HNO3 and 30 min of sonication in a 25 kHz US bath (37.2 ± 4.0 W L-1) at 70% of amplitude and 70 °C. Analytes were quantified using inductively coupled plasma mass spectrometry and results were compared with values obtained using "silent" conditions (magnetic or mechanical stirring at 500 rpm, and without stirring), and a reference method based on microwave-assisted wet digestion (MAWD). The UAE method demonstrated the best extraction efficiency (higher than 95%) for all analytes, especially for As, Cd and V, with lower standard deviations (up to 5%) and lower blank values in comparison with the silent conditions. The proposed UAE method was more advantageous than the reference method, being faster, simpler, safer, more environmentally friendly, and with higher detectability (lower limits of quantification, from 0.0033 to 1.34 µg g-1). In addition, negligible blank values were obtained for UAE and no interference were observed in the determination step. Furthermore, the optimized UAE method was applied for Antarctic seaweed samples and comparison with results obtained by MAWD was satisfactory. In this sense, UAE is demonstrated to be a suitable option for sample preparation of seaweed samples and further determination of environmentally critical elements avoiding the use of concentrated reagents as in the MAWD reference method.

New Analytical Strategy for Bioaccessibility Evaluation of Bromine and Iodine from Edible Seaweeds.

A strategy for determining the bioaccessibility of bromine and iodine from edible seaweeds was proposed for the first time using microwave-induced combustion (MIC) and ion chromatography coupled to mass spectrometry (IC-MS) after in vitro digestion. The concentrations of bromine and iodine in edible seaweeds using the proposed methods (MIC and IC-MS) were not statistically different from those using MIC and inductively coupled plasma mass spectrometry (p > 0.05). Trueness was assessed by recovery experiments (101-110%, relative standard deviation <10%). Following an in vitro digestion protocol, MIC was proposed as sample preparation for bioaccessible and residual fractions. Using this strategy, the mass balance totaled from 97 to 111%. No statistical difference (p > 0.05) was observed between the total concentration of bromine or iodine and their concentration in bioaccessible and residual fractions for three edible seaweed species, indicating full analyte quantification in the fractions.

Microwave-induced self-ignition: An efficient approach for high purity graphite digestion and multitechnique halogen determination.

In this work, high purity graphite, a high chemically stable material, was effectively digested using a single method allowing compatible solutions for the further multitechnique determination of halogens by: ion chromatography (F and Cl), inductively coupled plasma mass spectrometry (Cl, Br and I) and by ion selective electrode (only for F). The recent system using microwave-induced self-ignition (MISI) is based on the strong interaction between microwave radiation and graphite in a closed system pressurized with oxygen (Maxwell-Wagner effect). Carbon-based materials present intense and specific interfacial polarization when exposed to microwave electromagnetic field resulting in a fast heating rate. This effect associated to a pressurized oxygen system, provides a quick self-ignition of carbon-based materials and consequent combustion/digestion of organic matrices. Under optimized conditions, sample masses up to 600 mg were fully digested in a quartz vessel under 20 bar of oxygen pressure and using just a diluted solution (100 mmol L-1 NH4OH) for the quantitative absorption of all the analytes. MISI method was validated, and the accuracy (better than 94%) was evaluated by comparison of results obtained by pyrohydrolysis for two coal certified reference materials as well as with subsequent analytes determination by the three techniques: IC, ICP-MS and ISE. It is important to point out that no filter paper disks, electrical connections or other ignition aids are required as in the case of previous or classical combustion methods. Moreover, just a diluted absorbing solution was used resulting in negligible blanks and relatively low limits of detection. The digestion efficiency was higher than 99%, making the proposed method a suitable and powerful alternative for the quasi complete digestion of graphite and determination of halogens virtually free of interferences.

A single step ultrasound-assisted nitrocellulose synthesis from microcrystalline cellulose.

Nitrocellulose is a nitrated cellulose polymer with a broad application in industry. Depending on the nitrogen content, this polymer can be used for manufacturing explosives, varnishes, clothes, and films, being considered a product of high value-added. In this work, the use of ultrasound was investigated for the intensification of nitrocellulose synthesis from microcrystalline cellulose. The ultrasound-assisted nitrocellulose synthesis (UANS) was carried out using several ultrasound systems, such as baths and cup horns, allowing the evaluation of the frequency (from 20 to 130 kHz) and delivered power (from 23 to 134 W dm-3) to the reaction medium. The following parameters were evaluated: acid mixture (H2SO4, H3PO4, CH2O2 or CH3COOH with HNO3, 2 to 14.4 mol L-1), ultrasound amplitude (10 to 70%) and reaction time (5 to 50 min). Better nitrocellulose yield (nitrogen content of 12.5% was obtained from 1 g of microcrystalline cellulose employing a cup horn system operating at 20 kHz, 750 W of nominal power with 60% of amplitude, 25 mL of acid solution (13.6 mL of 18.4 mol L-1 H2SO4 + 9.2 mL of 14.4 mol L-1 HNO3 + 2.2 mL H2O), at 30 °C for 30 min. At silent conditions (mechanical stirring ranging from 100 to 500 rpm), the nitrogen content was lower than 11.8% which demonstrate the ultrasound effects for nitrocellulose synthesis.

A solid sampling approach for direct determination of Cl and S in flour by an elemental analyzer.

Direct analysis of flour was proposed for the determination of Cl and S by an elemental analyzer for the first time. The main operational conditions of the direct solid sampling elemental analysis (DSS-EA) were optimized and calibrated by standard solutions, rather than by certified reference material (CRM). Accuracy was evaluated by the analysis of CRM of rice flour and by comparison with analyte determination by independent techniques, i.e., ion chromatography and inductively coupled plasma optical emission spectrometry; both were carried out after microwave-induced combustion. Sample mass from 0.5 to 260 mg was used and limits of quantification of 1.2 µg g-1 for Cl and 0.2 µg g-1 for S were achieved. Wheat, whole wheat, potato and corn flour were analyzed by DSS-EA. Concentrations of Cl and S ranged from 4.8 to 685 µg g-1 and from 13 to 1328 µg g-1, respectively.

Focused microwave-induced combustion: a new technique for sample digestion.

A procedure for sample digestion based on focused microwave-induced combustion (FMIC) is proposed. This system was developed using a commercial focused microwave oven with a lab-made quartz sample holder and a modified glass vessel. Oxygen flow was used to start and support the combustion. A botanical sample was used to evaluate the operational conditions for further Al, Ba, Ca, Fe, Mg, Mn, Sr, and Zn determination by inductively coupled plasma optical emission spectrometry. Pelletized samples were positioned on the quartz holder, and 50 microL of 6 mol L(-1) NH(4)NO(3) solution was added as igniter. Combustion was completed in less than 2 min, and the temperature was higher than 950 degrees C. The use of a reflux step, the position of sample holder inside the vessel, sample mass, ignition and combustion time, oxygen flow rate, and condenser type were evaluated. Results were compared with those obtained by focused microwave-assisted wet digestion and by high pressure microwave-assisted wet digestion. Agreement of 95-103% was obtained for certified reference materials digested by FMIC (reflux step with 10 mL of 4 mol L(-1) HNO(3)). With the proposed procedure, a complete sample decomposition (residual carbon content lower than 0.5%) was achieved with low consumption of reagents as only 10 mL of diluted nitric acid was necessary. Low relative standard deviation (lower than 3.8%) was observed and high amount of sample (up to 1500 mg) could be digested that allowed lower limits of detection.

Iodine determination in food by inductively coupled plasma mass spectrometry after digestion by microwave-induced combustion.

Iodine determination in food samples was performed by inductively coupled plasma mass spectrometry (ICP-MS) after digestion by microwave-induced combustion (MIC). Sample masses up to 500 mg of bovine liver, corn starch, milk powder, or wheat flour were completely combusted using the MIC system. Ammonium nitrate (6 mol l(-1) solution, 50 µl) was used as an aid for ignition and vessels were charged with 15 bar of O(2). The use of H(2)O, 0.9 mmol l(-1) H(2)O(2), 10 to 50 mmol l(-1) (NH(4))(2)CO(3) and 56 mmol l(-1) tetramethylammonium hydroxide was investigated as absorbing solutions, as well as the suitability of performing a reflux step after the combustion process. Digestion of food samples by pressurized microwave-assisted acid digestion, microwave-assisted extraction and conventional extraction of iodine in alkaline solution were also evaluated. Iodine recoveries higher than 99% were obtained using MIC and 50 mmol l(-1) (NH(4))(2)CO(3) or 56 mmol l(-1) tetramethylammonium hydroxide as absorbing solution and with 5 min for the reflux step. Accuracy was evaluated using certified reference materials (bovine muscle, corn bran, and milk powder) and agreement better than 97% was obtained. The limit of quantification by MIC and further ICP-MS determination was 0.002 µg g(-1). Blanks were always low and no memory effects were observed. Digestion by MIC allowed the processing of up to eight samples by each run in 25 min with high efficiency of digestion (residual carbon content lower than 1%) providing a suitable medium for further iodine determination by ICP-MS.

Evaluation of sample preparation methods for elastomer digestion for further halogens determination.

In this work, three sample preparation methods were evaluated for further halogen determination in elastomers containing high concentrations of carbon black. Samples of nitrile-butadiene rubber, styrene-butadiene rubber, and ethylene-propylene-diene monomer elastomers were decomposed using oxygen flask combustion and microwave-induced combustion (MIC) for further Br and Cl determination by ion chromatography (IC), inductively coupled plasma optical emission spectrometry (ICP OES), and inductively coupled plasma mass spectrometry (ICP-MS). Extraction assisted by microwave radiation in closed vessels was also evaluated using water or alkaline solution. Digestion by MIC was carried out using 50 mmol l(-1) (NH(4))(2)CO(3) as the absorbing solution. The effect of the reflux step was also evaluated. Accuracy was evaluated using certified reference materials with polymeric matrix composition and by comparison of results using neutron activation analysis. Agreement for Br and Cl was better than 95% by MIC using 5 min of reflux, and no statistical difference was found using IC, ICP OES, and ICP-MS for determination of both analytes. For MIC, the relative standard deviation (RSD) was lower than 5%. Using extraction in closed vessels, a high amount of residues was observed, and recoveries were lower than 45% for both analytes. For oxygen flask combustion, the agreement was similar using MIC but RSD was higher (20%). The residual carbon content, an important parameter used to evaluate the digestion efficiency, was always below 1% for MIC. Using MIC, it was possible to digest elastomers with high efficiency, resulting in a single solution suitable for halogen determination by different techniques.

Evaluation of sample preparation methods for cereal digestion for subsequent As, Cd, Hg and Pb determination by AAS-based techniques.

Sample preparation methodsforcereal digestion were evaluated for the first time for subsequent As, Cd, Hg, and Pb determination by atomic absorption spectroscopy techniques. Microwave-assisted digestion (MW-AD) under high and medium pressure and microwave-induced combustion (MIC) were evaluated. The use of MIC made it possible to digest 700 mg of samples, and agreements of 97, 96, 100 and 92% were obtained for As, Cd, Hg and Pb, respectively, when 7 mol L-1 HNO3 was used as the absorbing solution. It was not necessary to dilute the digests obtained to avoid interferences in the quantification of As, Cd, Hg, and Pb. Although high pressure MW-AD was efficient for cereal digestion, interferences were observed on analyte determination. Limits of quantification obtained by MIC were 0.034 (As), 0.015 (Cd), 0.021 (Hg) and 0.105 (Pb) µg g-1, which are suitable to attain the maximum levels recommended by international agencies in cereal samples.

Advances in the Understanding of Oxaliplatin-Induced Peripheral Neuropathy in Mice: 7-Chloro-4-(Phenylselanyl) Quinoline as a Promising Therapeutic Agent.

In this study, the deposition of platinum in oxaliplatin (OXA)-exposed mice and the effects of the oxidative damage on the central nervous system were investigated. The relationship between the reactive species (RS) levels as well as the expression and activity of enzymes, such as catalase (CAT), glutathione peroxidase (GPx), superoxide dismutase (SOD) and acetylcholinesterase (AChE), in the development of peripheral neuropathy after OXA exposure, was evidenced. The effects of 7-chloro-4-(phenylselanyl) quinoline (4-PSQ) on OXA-induced peripheral neuropathy was also investigated. Swiss mice received OXA (10 mg kg-1) or vehicle by intraperitoneal route (days 0 and 2). Oral administration of 4-PSQ (1 mg kg-1) or vehicle was performed on days 2 to 14. Behavioural tasks started on day 9, after the first OXA administration. It was observed that 4-PSQ reduced the mechanical and thermal hypersensitivity induced by OXA. 4-PSQ and OXA did not affect locomotor and exploratory activities. The results revealed, for the first time, a high concentration of platinum in the spinal cord of mice exposed to OXA. 4-PSQ reversed the increased levels of RS in the spinal cord, cerebral cortex and hippocampus of mice exposed to OXA. The alterations in the activity and expression of the GPx, SOD, CAT and AChE induced by OXA exposure were normalized by 4-PSQ. Therefore, the 4-PSQ might be a good prototype for the development of a more effective drug for the treatment of OXA-induced peripheral neuropathy. The results obtained by the present study expanded the knowledge about the mechanisms involved in the physiopathology of peripheral neuropathy. Graphical abstract.

Determination of trace elements in Sergio mirim: an evaluation of sample preparation methods and detection techniques.

In this work, some trace elements (As, Cd, Cr, Cu, and Pb) were determined for the first time in the crustacean Sergio mirim (Decapoda: Thalassinidea: Callianassidae) from Southern Coast (Rio Grande, RS) of Brazil. The trace element determination was carried out by graphite furnace atomic absorption spectrometry (GF AAS) and inductively coupled plasma mass spectrometry (ICP-MS). Different microwave radiation-based sample digestion methods were evaluated. The analyte concentration ranged from 1.45 to 3.70 µg g-1 for As, 0.615 to 0.942 µg g-1 for Cd, 0.884 to 7.20 µg g-1 for Cr, 122 to 275 µg g-1 for Cu, and 0.390 to 0.916 µg g-1 for Pb. The limits of quantification for As, Cd, Cr, Cu, and Pb were 0.12, 0.01, 0.16, 0.92, and 0.06 µg g-1, respectively. The accuracy was evaluated by results comparison between GF AAS and ICP-MS techniques, as well as by analysis of certified reference materials of fish muscle and oyster tissue, with agreement from 92 to 108%. The feasibility of using Sergio mirim as a promising environmental bioindicator candidate was evaluated, since that it is an abundant organism in the studied area (South cost of Brazil) as well as in other places around the world.

Protective effect of high alkalinity against the deleterious effects of chronic waterborne cadmium exposure on the detection of alarm cues by juvenile silver catfish (Rhamdia quelen).

The objective of the present study was to analyze the effect of chronic cadmium (Cd) exposure at two alkalinity levels (63 and 92 mg l(-1) CaCO(3)) on the antipredatory behavior of juvenile silver catfish (Rhamdia quelen) exposed to conspecific skin extract and predator odor. At an alkalinity of 63 mg l(-1) CaCO(3), 30 days of exposure to either 4.5 or 8.0 microg l(-1) Cd impaired the catfish's antipredatory response to alarm cues. However, silver catfish exposed to 4.5 microg l(-1) Cd at an alkalinity of 92 mg l(-1) CaCO(3) responded to skin extract and predator odor. In catfish exposed to 8.0 microg l(-1) Cd at the same alkalinity, only the number of feeding bites decreased, and this occurred only for specimens exposed to predator odor. Our results show that higher alkalinity protected against the deleterious effects of Cd on alarm cue detection but only in the larvae exposed to the lowest waterborne Cd level.

A versatile green analytical method for determining chlorine and sulfur in cereals and legumes.

A versatile, rapid and safe green method for chlorine and sulfur determination using ion chromatography in cereals and legumes was developed. Microwave-induced combustion was evaluated for sample preparation. Ultrapure water and alkaline solutions were assessed for absorption of the analytes. Water was selected because good recoveries (97-109%) were obtained for both analytes. Low consumption of reagents and small quantities of waste are two important advantages of the proposed method. Accuracy was evaluated by analysis of a standard reference material, which agreed with certified values (91-101%). The results for repeatability (RSDs ≤ 4%) and intermediate precision (RSDs ≤ 7%) prove the good precision of the proposed method. Limits of quantification were 16 and 17 mg kg-1 for Cl and S, respectively. Concentrations of Cl and S varied across a wide range (Cl: 35-930 mg kg-1; S: 678-5124 mg kg-1) for 34 samples analyzed, which were, for most of the results, close to the values found in the literature.

Biochemistry, cytogenetics and bioaccumulation in silver catfish (Rhamdia quelen) exposed to different thorium concentrations.

The objective of this study was to evaluate the effect of thorium (Th) bioaccumulation on the metabolism of silver catfish (Rhamdia quelen) through biochemical parameters of the muscle (glycogen, glucose, lactate, protein, and ammonia). In addition, lipidic peroxidation levels (TBARS), catalase (CAT) and glutathione-S-transferase (GST) in the gills and in hepatic and muscular tissues were also analyzed. Cytogenetic parameters were studied through the evaluation of nuclear abnormalities in red blood cells. Silver catfish juveniles were exposed to different waterborne Th levels (in microg L(-1)): 0 (control), 25.3+/-3.2, 69.2+/-2.73, 209.5+/-17.6, and 608.7+/-61.1 for 15 days. The organs that accumulated the highest Th levels were the gills and skin. The increase of waterborne Th concentration corresponded to a progressive increase of Th levels in the gills, liver, skin and kidneys, with the highest accumulation in the gills and skin. Metabolic intermediates in the muscle were altered by Th exposure, but no clear relationship was found. CAT and GST activities in the hepatic and muscular tissues of this species suggest that the enzymatic activities can be stimulated at the lowest Th levels and inhibited at the higher levels (mainly in 608.7 microg L(-1)). The results of the cytogenetic assay contribute to this hypothesis because the higher toxicity in blood samples was found in juveniles exposed to 69.2 and 209.5 microg L(-1) Th.

A novel and eco-friendly analytical method for phosphorus and sulfur determination in animal feed.

An eco-friendly method for indirect determining phosphorus and sulfur in animal feed by ion chromatography was proposed. Using this method, it was possible to digest 500 mg of animal feed in a microwave system under oxygen pressure (20 bar) using only a diluted acid solution (2 mol L-1 HNO3). The accuracy of the proposed method was evaluated by recovery tests, by analysis of reference material (RM) and by comparison of the results with those obtained using conventional microwave-assisted digestion. Moreover, P results were compared with those obtained from the method recommended by AOAC International for animal feed (Method nr. 965.17) and no significant differences were found between the results. Recoveries for P and S were between 94 and 97%, and agreements with the reference values of RM were better than 94%. Phosphorus and S concentrations in animal feeds ranged from 10,026 to 28,357 mg kg-1 and 2259 to 4601 mg kg-1, respectively.

A selective volatilization method for determination of chloride and sulfate in calcium carbonate pharmaceutical raw material and commercial tablets.

In this work a feasible method for chloride and sulfate determination in calcium carbonate pharmaceutical raw material and commercial tablets by ion chromatography after microwave-induced combustion was developed. The analytes were released from matrix by combustion in closed system pressurized with oxygen. Starch as volatilization aid, 100mmolL-1 HNO3 as absorbing solution and 5min of microwave irradiation time were used. Recovery tests using standard solutions were performed for the accuracy evaluation. A mixture of calcium carbonate pharmaceutical raw material or commercial tablets, starch and a certified reference material was also used as a type of recovery test. Recoveries ranging from 88% to 103% were obtained in both spike tests. Limits of detection (Cl-: 40µgg-1 and SO42-: 140µgg-1) were up to eighteen times lower than the maximum limits established for the analytes by Brazilian, British, European and Indian Pharmacopoeias. The limit tests recommended by the European Pharmacopoeia for Cl- and SO42- in CaCO3 were carried out to compare the results. Chloride and SO42- concentrations in the samples analyzed by proposed method were in agreement with those results obtained using the tests recommended by the European Pharmacopoeia. However, the proposed method presents several advantages for the routine analysis when compared to pharmacopoeial methods, such as the quantitative simultaneous determination, high sample preparation throughput (up to eight samples per run in less than 30min), reduced volume of reagents and waste generation. Thus, the proposed method is indicated as an excellent alternative for Cl- and SO42- determination in CaCO3 pharmaceutical raw material and commercial tablets.