RESUMO
Highly stretchable electrically conductive hydrogels have been extensively researched in recent years, especially for applications in strain and pressure sensing, electronic skin, and implantable bioelectronic devices. Herein, we present a new cross-linked complex coacervate approach to prepare conductive hydrogels that are both highly stretchable and compressive. The gels involve a complex coacervate between carboxylated nanogels and branched poly(ethylene imine), whereby the latter is covalently cross-linked by poly(ethylene glycol) diglycidyl ether (PEGDGE). Inclusion of graphene nanoplatelets (Gnp) provides electrical conductivity as well as tensile and compressive strain-sensing capability to the hydrogels. We demonstrate that judicious selection of the molecular weight of the PEGDGE cross-linker enables the mechanical properties of these hydrogels to be tuned. Indeed, the gels prepared with a PEGDGE molecular weight of 6000 g/mol defy the general rule that toughness decreases as strength increases. The conductive hydrogels achieve a compressive strength of 25 MPa and a stretchability of up to 1500%. These new gels are both adhesive and conformal. They provide a self-healable electronic circuit, respond rapidly to human motion, and can act as strain-dependent sensors while exhibiting low cytotoxicity. Our new approach to conductive gel preparation is efficient, involves only preformed components, and is scalable.
Assuntos
Grafite , Dispositivos Eletrônicos Vestíveis , Adesivos , Condutividade Elétrica , Humanos , HidrogéisRESUMO
Microgels (MGs) are crosslinked polymer colloid particles that swell in a good solvent. Although MGs have been studied for over 80 years their ability to control the morphology and optoelectronic properties of composite films containing photoactive materials is in its infancy. Solution processable hybrid organic-inorganic perovskites such as CH3NH3PbI3-zClz have attracted enormous fundamental and applied interest because of their outstanding optoelectronic properties. There is considerable interest in establishing methods to control perovskite film morphology, for example, using micropatterning. Here, hydrophilic poly(N-vinylformamide)-based MGs were dispersed in perovskite precursor solution which was then spin coated to deposit CH3NH3PbI3-zClz/MG films for the first time. Remarkably, the CH3NH3PbI3-zClz/MG composites formed disordered inverse opal (DIO) films. The CH3NH3PbI3-zClz/MG composition ranges which gave DIO films are identified using a phase diagram. The pore wall thickness is shown to be controlled by the volume fraction of MGs used and a simple model is presented to explain this behaviour. The MGs not only caused CH3NH3PbI3-zClz to be more efficiently deposited but also increased light absorption and photoluminescence intensity. Demonstration solar cells constructed containing the DIO CH3NH3PbI3-zClz/MG films had an average conversion efficiency of 6.58 ± 0.81%. A mechanism for DIO film formation is discussed. The principles established in this study wherein MGs control the morphology and properties of CH3NH3PbI3-zClz/MG films should also apply to other perovskite/MG composites.
RESUMO
Blends of semiconducting nanocrystals and conjugated polymers continue to attract major research interest because of their potential applications in optoelectronic devices, such as solar cells, photodetectors and light-emitting diodes. In this study we investigate the surface structure, morphological and optoelectronic properties of multilayer films constructed from ZnO nanocrystals (NCs) and poly[2-methoxy-5-(3',7'-dimethyloctyloxy)-1,4-phenylenevinylene] (MDMO-PPV). The effects of layer number and ZnO concentration (CZnO) used on the multilayer film properties are investigated. An optimised solvent blend enabled well-controlled layers to be sequentially spin coated and the construction of multilayer films containing six ZnO NC (Z) and MDMO-PPV (M) layers (denoted as (ZM)6). Contact angle data showed a strong dependence on CZnO and indicated distinct differences in the coverage of MDMO-PPV by the ZnO NCs. UV-visible spectroscopy showed that the MDMO-PPV absorption increased linearly with the number of layers in the films and demonstrates highly tuneable light absorption. Photoluminescence spectra showed reversible quenching as well as a surprising red-shift of the MDMO-PPV emission peak. Solar cells were constructed to probe vertical photo-generated charge transport. The measurements showed that (ZM)6 devices prepared using CZnO = 14.0 mg mL-1 had a remarkably high open circuit voltage of â¼800 mV. The device power conversion efficiency was similar to that of a control bilayer device prepared using a much thicker MDMO-PPV layer. The results of this study provide insight into the structure-optoelectronic property relationships of new semiconducting multilayer films which should also apply to other semiconducting NC/polymer combinations.
RESUMO
Perovskite solar cells continue to attract strong attention because of their unprecedented rate of power conversion efficiency increase. CH3NH3PbI3 (MAPbI3) is the most widely studied perovskite. Typically one-step (1-s) or two-step (2-s) deposition methods are used to prepare MAPbI3 films. Here, we investigate a new MAPbI3 film formation method that combines 1-s and 2-s deposition (termed 1 & 2-s) and uses systematic variation of the stoichiometric mole ratio (x) for the PbI2 + xMAI solutions employed. The PbI2 + xMAI solutions were used to deposit precursor films that were subsequently dipped in MAI solution as a second step to produce the final MAPbI3 films. The morphologies of the 1 & 2-s MAPbI3 films consisted of three crystal types: tree-like microcrystals (â«1 µm), cuboid meso-crystals (â¼0.1-1 µm) and nanocrystals (â¼50-80 nm). Each crystal type and their proportions were controlled by the value for x. The new 1 & 2-s deposition method produced MAPbI3 films with tuneable optoelectronic properties that were related to those for the conventional 1-s and 2-s films. However, the 1 & 2-s film properties were not simply a combination of those for the 1-s and 2-s films. The 1 & 2-s films showed enhanced light scattering and the photoluminescence spectra displayed a morphologically-dependent red-shift. The unique morphologies for the 1 & 2-s films also strongly influenced PbI2 conversion, power conversion efficiency, hysteresis and recombination. The trends for the performance parameters and hysteresis were compared for devices constructed using spiro-MeOTAD and P3HT and were similar. The 1 & 2-s method should apply to other perovskite formulations and the new insights concerning MAPbI3 crystal growth conditions, morphology and material properties established in this study should also be transferable.
RESUMO
Due to its high electron mobility, good stability and potential for low-temperature synthesis ZnO has received considerable attention for use in solar cells, photodetectors and sensors. Whilst there have been reports involving the formation ZnO films with porous morphologies the majority of those have involved elaborate or time-consuming preparation methods. In this study we investigate a simple new method for preparing textured porous ZnO (tp-ZnO) films. We used colloidal instability triggered by the evaporation of a volatile stabilising ligand during spin-coating of a ZnO nanocrystal (NC) dispersion to deposit crack-free tp-ZnO films. The porosity of the tp-ZnO films was 56% and they could be prepared using amine-based ligands with boiling points less than or equal to 78 °C. To demonstrate the ability to use the tp-ZnO films as electron acceptors they were infiltrated with poly(3-hexylthiophene) (P3HT) and solar cells prepared. The power conversion efficiencies of the tp-ZnO/P3HT devices reached values that were three times higher than a control bilayer ZnO/P3HT device prepared using a sol-gel derived ZnO film. Because our method used a low temperature treatment and ZnO films are used in a wide variety of third-generation solar cells, the new tp-ZnO films introduced here may offer a low cost method for improving the efficiency of other solar cells.
RESUMO
Hybrid halide perovskites materials have the potential for both photovoltaic and light-emitting devices. Relatively little has been reported on the kinetics of charge relaxation upon intense excitation. In order to evaluate the illumination power density dependence on the charge recombination mechanism, we have applied a femtosecond transient mid-IR absorption spectroscopy with strong excitation to directly measure the charge kinetics via electron absorption. The irradiance-dependent relaxation processes of the excited, photo-generated charge pairs were quantified in polycrystalline MAPbI3, MAPbBr3, and (FAPbI3)0.97(MAPbBr3)0.03 thin films that contain either methylamonium (MA) or formamidinium (FA). This report identifies the laser-generated charge species and provides the kinetics of Auger, bimolecular and excitonic decay components. The inter-band electron-hole (bimolecular) recombination was found to dominate over Auger recombination at very high pump irradiances, up to the damage threshold. The kinetic analysis further provides direct evidence for the carrier field origin of the vibrational Stark effect in a formamidinium containing perovskite material. The results suggest that radiative excitonic and bimolecular recombination in MAPbI3 at high excitation densities could support light-emitting applications.
RESUMO
Additive engineering has been applied widely to improve the efficiency and/or stability of perovskite solar cells (PSCs). Most additives used to date are difficult to locate within PSCs as they are small molecules or linear polymers. In this work, we introduce, for the first time, carboxylic acid-functionalized nanogels (NGs) as additives for PSCs. NGs are swellable sub-100 nm gel particles. The NGs consist of poly(2-(2-methoxyethoxy) ethyl methacrylate)-co-methacrylic acid-co-ethylenegylcol dimethacrylate (PMEO2MA-MAA-EGD) particles prepared by a scalable synthesis, which have a diameter of 40 nm. They are visualized in the perovskite films using SEM and are located at the grain boundaries. X-ray photoelectron and FTIR spectroscopy reveal that the NGs coordinate with Pb2+ via the -COOH groups. Including the NGs within the PSCs increased the grain size, decreased nonradiative recombination, and increased the power conversion efficiency (PCE) to 20.20%. The NGs also greatly increase perovskite stability to ambient storage, elevated temperature, and humidity. The best system maintained more than 80% of its original PCE after 180 days of storage under ambient conditions. Tensile cross-cut tape adhesion tests are used to assess perovskite film mechanical integrity. The NGs increased both the adhesion of the perovskite to the substrate and the mechanical stability. This study demonstrates that NGs are an attractive alternative to molecularly dispersed additives for providing performance benefits to PSCs. Our study indicates that the NGs act as a passivator, stabilizer, cross-linker, and adhesion promoter.
RESUMO
Hydroxyapatite nanoparticles (HAP NPs) are blended with TiO2 NPs to prepare mixed mesoporous scaffolds which are used to prepare high efficiency perovskite solar cells (PSCs) with a best power conversion efficiency (PCE) of 20.98%. HAP not only increases the PCE but also limits the concentration of Pb released in water from intentionally broken PSCs by ion sequestration thereby potentially offering a promising in-device fail-safe system.
Assuntos
Compostos de Cálcio/química , Fontes de Energia Elétrica , Chumbo/química , Óxidos/química , Energia Solar , Titânio/química , Durapatita , Microscopia Eletrônica de Varredura , Estrutura Molecular , NanopartículasRESUMO
The mesoporous (meso)-TiO2 layer is a key component of high-efficiency perovskite solar cells (PSCs). Herein, pore size controllable meso-TiO2 layers are prepared using spin coating of commercial TiO2 nanoparticle (NP) paste with added soft polymer templates (SPT) followed by removal of the SPT at 500 °C. The SPTs consist of swollen crosslinked polymer colloids (microgels, MGs) or a commercial linear polymer (denoted as LIN). The MGs and LIN were comprised of the same polymer, which was poly(N-isopropylacrylamide) (PNIPAm). Large (L-MG) and small (S-MG) MG SPTs were employed to study the effect of the template size. The SPT approach enabled pore size engineering in one deposition step. The SPT/TiO2 nanoparticle films had pore sizes > 100 nm, whereas the average pore size was 37 nm for the control meso-TiO2 scaffold. The largest pore sizes were obtained using L-MG. SPT engineering increased the perovskite grain size in the same order as the SPT sizes: LIN < S-MG < L-MG and these grain sizes were larger than those obtained using the control. The power conversion efficiencies (PCEs) of the SPT/TiO2 devices were â¼20% higher than that for the control meso-TiO2 device and the PCE of the champion S-MG device was 18.8%. The PCE improvement is due to the increased grain size and more effective light harvesting of the SPT devices. The increased grain size was also responsible for the improved stability of the SPT/TiO2 devices. The SPT method used here is simple, scalable, and versatile and should also apply to other PSCs.
RESUMO
Perovskite solar cells (PSCs) are a disruptive technology that continues to attract considerable attention due to their remarkable and sustained power conversion efficiency increase. Improving PSC stability and reducing expensive hole transport material (HTM) usage are two aspects that are gaining increased attention. In a new approach, we investigate the ability of insulating polystyrene microgel particles (MGs) to increase PSC stability and replace the majority of the HTM phase. MGs are sub-micrometre crosslinked polymer particles that swell in a good solvent. The MGs were prepared using a scalable emulsion polymerisation method. Mixed HTM/MG dispersions were subsequently spin-coated onto PSCs and formed composite HTM-MG layers. The HTMs employed were poly(triaryl amine) (PTAA), poly(3-hexylthiophene) (P3HT) and Spiro-MeOTAD (Spiro). The MGs formed mechanically robust composite HTMs with PTAA and P3HT. In contrast, Spiro-MG composites contained micro-cracks due the inability of the relatively small Spiro molecules to interdigitate. The efficiencies for the PSCs containing PTAA-MG and P3HT-MG decreased by only â¼20% compared to control PSCs despite PTAA and P3HT being the minority phases. They occupied only â¼35 vol% of the composite HTMs. An unexpected finding from the study was that the MGs dispersed well within the PTAA matrix. This morphology aided strong quenching of the CH3NH3PbI3-xClx fluorescence. In addition, the open circuit voltages for the PSCs prepared using P3HT-MG increased by â¼170 mV compared to control PSCs. To demonstrate their versatility the MGs were also used to encapsulate P3HT-based PSCs. Solar cell stability data for the latter as well as those for PSCs containing composite HTM-MG were both far superior compared to data measured for a control PSC. Since MGs can reduce conjugated polymer use and increase stability they have good potential as dual-role PSC additives.