An accelerated PETALUTE MRI sequence for in vivo quantification of sodium content in human articular cartilage at 3T.

OBJECTIVE: In this work, we evaluate the sodium magnetic resonance imaging (MRI) capabilities of a three-dimensional (3D) dual-echo ultrashort echo time (UTE) sequence with a novel rosette petal trajectory (PETALUTE), in comparison to the 3D density-adapted (DA) radial spokes UTE sequence in human articular cartilage in the knee. MATERIALS AND METHODS: We scanned five healthy subjects using a 3D dual-echo PETALUTE acquisition and two comparable implementations of 3D DA-radial spokes acquisitions, one matching the number of k-space projections (Radial - Matched Spokes) and the other matching the total number of samples (Radial - Matched Samples) acquired in k-space. RESULTS: The PETALUTE acquisition enabled equivalent sodium quantification in articular cartilage volumes of interest (168.8 ± 29.9 mM, mean ± standard deviation) to those derived from the 3D radial acquisitions (171.62 ± 28.7 mM and 149.8 ± 22.2 mM, respectively). We achieved a 41% shorter scan time of 2:06 for 3D PETALUTE, compared to 3:36 for 3D radial acquisitions. We also evaluated the feasibility of further acceleration of the PETALUTE sequence through retrospective compressed sensing with 2 × and 4 × acceleration of the first echo and showed structural similarity of 0.89 ± 0.03 and 0.87 ± 0.03 when compared to non-retrospectively accelerated reconstruction. CONCLUSION: We demonstrate improved scan time with equivalent performance using a 3D dual-echo PETALUTE sequence compared to the 3D DA-radial sequence for sodium MRI of articular cartilage.

An improved intraoral transverse loop coil design for high-resolution dental MRI.

PURPOSE: To improve intraoral transverse loop coil design for high-resolution dental MRI. METHODS: The transverse intraoral loop coil (tLoop) was modified (mtLoop) by overlapping the feed port conductors, bending the posterior section, introducing a parallel plate capacitor, optimizing the insulation thickness, and using it in receive-only mode. In addition, an MR-silent insulation was introduced. The performances of the mtLoop and tLoop coils were compared in terms of sensitivity, image SNR, and eddy currents using electromagnetic simulations and MRI measurements at 3T. RESULTS: The receive-only mode of the mtLoop increases the sensitivity at the apices of the roots, and the overlapped feed port design eliminated signal voids along the incisors. The bent posterior section with the parallel plate capacitor reduced the unwanted signal of the tongue by a factor of 2.3 in the selected region off interest and lowered the eddy currents by 10%. The proposed new coil provided higher SNR by elevenfold and 2.5-fold at the incisors and apices of the molar roots within the selected regions of interest, respectively, in the experiments, as well as improved comfort. Optimal insulation thickness was determined as 1 mm. With the mtLoop, a (250 µm)3 isotropic resolution of the dental arch could be realized using a UTE sequence within 2 min total acquisition time. A T2 -SPACE protocol with (350 µm)2 in-plane resolution was also demonstrated. CONCLUSION: The proposed new coil offers higher SNR at the incisors and apices of the molar roots, less unwanted signals from tongue, lower eddy currents, and improved patient comfort.

Ultra-short T2 components imaging of the whole brain using 3D dual-echo UTE MRI with rosette k-space pattern.

PURPOSE: This study aimed to develop a new 3D dual-echo rosette k-space trajectory, specifically designed for UTE MRI applications. The imaging of the ultra-short transverse relaxation time (uT2 ) of brain was acquired to test the performance of the proposed UTE sequence. THEORY AND METHODS: The rosette trajectory was developed based on rotations of a "petal-like" pattern in the kx -ky plane, with oscillated extensions in the kz -direction for 3D coverage. Five healthy volunteers underwent 10 dual-echo 3D rosette UTE scans with various TEs. Dual-exponential complex model fitting was performed on the magnitude data to separate uT2 signals, with the output of uT2 fraction, uT2 value, and long-T2 value. RESULTS: The 3D rosette dual-echo UTE sequence showed better performance than a 3D radial UTE acquisition. More significant signal intensity decay in white matter than gray matter was observed along with the TEs. The white matter regions had higher uT2 fraction values than gray matter (10.9% ± 1.9% vs. 5.7% ± 2.4%). The uT2 value was approximately 0.10 ms in white matter . CONCLUSION: The higher uT2 fraction value in white matter compared to gray matter demonstrated the ability of the proposed sequence to capture rapidly decaying signals.

Scalable and modular 8-channel transmit and 8-channel flexible receive coil array for 19 F MRI of large animals.

PURPOSE: To introduce an RF coil system consisting of an 8-channel transmit (Tx) and 8-channel receive (Rx) coil arrays for 19 F MRI of large animals. METHODS: The Tx efficiency and homogeneity of the 8-element loop coil array (loop size: 6 × 15 cm2 ) were simulated for two different pig models rendered from MR images. An 8-channel Rx coil array consisting of a flexible 6-channel posterior and a 2-channel planar anterior array was designed to fit on the abdomen of an average-sized pig in supine position. Measurements were performed in a grid phantom and ex vivo on a pig model with perfluoroctylbromide (PFOB)-filled tubes inserted in the thorax. RESULTS: Measured and simulated Tx efficiency and homogeneity for the 8-channel and 5-channel arrays were in good agreement: 1.87 ± 0.22µT/√kW versus 1.96 ± 0.29µT/√kW, and 2.29 ± 0.39µT/√kW versus 2.41 ± 0.37µT/√kW. An isolation of 38 ± 8 dB is achieved between the 19 F Tx and Rx elements, and over 30 dB between the 1 H and 19 F elements. The PFOB-filled vials could be clearly identified within the cadaver abdomen with an SNR of 275 ± 51 for a 3D gradient-echo sequence with 2-mm isotropic resolution and 12 averages, acquired in 9:52 min:s. Performance of the Tx array was robust against phase and amplitude mismatches at the input ports. CONCLUSIONS: A modular and scalable Tx array offers improved Tx efficiency in 19 F MRI of large animals with various sizes. Although conventional birdcage coils have superior Tx efficiency within the target region of interest, scalability of the Tx array to animal size is a major benefit. The described 19 F coil provides homogeneous excitation and high sensitivity detection in large pig models.

RF-induced heating of interventional devices at 23.66 MHz.

OBJECTIVE: Low-field MRI systems are expected to cause less RF heating in conventional interventional devices due to lower Larmor frequency. We systematically evaluate RF-induced heating of commonly used intravascular devices at the Larmor frequency of a 0.55 T system (23.66 MHz) with a focus on the effect of patient size, target organ, and device position on maximum temperature rise. MATERIALS AND METHODS: To assess RF-induced heating, high-resolution measurements of the electric field, temperature, and transfer function were combined. Realistic device trajectories were derived from vascular models to evaluate the variation of the temperature increase as a function of the device trajectory. At a low-field RF test bench, the effects of patient size and positioning, target organ (liver and heart) and body coil type were measured for six commonly used interventional devices (two guidewires, two catheters, an applicator and a biopsy needle). RESULTS: Electric field mapping shows that the hotspots are not necessarily localized at the device tip. Of all procedures, the liver catheterizations showed the lowest heating, and a modification of the transmit body coil could further reduce the temperature increase. For common commercial needles no significant heating was measured at the needle tip. Comparable local SAR values were found in the temperature measurements and the TF-based calculations. CONCLUSION: At low fields, interventions with shorter insertion lengths such as hepatic catheterizations result in less RF-induced heating than coronary interventions. The maximum temperature increase depends on body coil design.

Radio-frequency induced heating of intra-cranial EEG electrodes: The more the colder?

Many neurological disorders are analyzed and treated with implantable electrodes. Many patients with such electrodes have to undergo MRI examinations - often unrelated to their implant - at the risk of radio-frequency induced heating. The number of electrode contact sites of these implants keeps increasing due to improvements in manufacturing and computational algorithms. Electrode grids with multiple receive channels couple to the RF fields present in MRI, but, due to their proximity, a combination of leads has a coupling response which is not a superposition of the individual leads' response. To investigate the problem of RF-induced heating of coupled multi-lead implants, temperature mapping was performed on a set of intra-cranial electroencephalogram (icEEG) electrode grid prototypes with increasing number of contact sites (1-16). Additionally, electric field measurements were used to investigate the radio-frequency heating characteristics of the implants in different media combinations, simulating the device being partially immersed inside the patient. MR measurements show RF-induced heating up to 19.6 K for the single electrode, reducing monotonically with larger number of contact sites to a minimum of 0.9 K for the largest grid. The SAR calculated from temperature measurements agrees well with electric field mapping: The same trend is visible for different insertion lengths, however, the energy dissipated by the whole implant varies with the grid size and insertion length. Thus, in the tested circumstances, a larger electrode number either reduced or had a similar risk of RF induced heating, indicating, that the size of electrode grids is a design parameter, which can be used to change an implants RF response and in turn to reduce the risk of RF induced heating and improve the safety of patient with neuro-implants undergoing MRI examinations.

Single point imaging with radial acquisition and compressed sensing.

PURPOSE: To accelerate the Pointwise Encoding Time Reduction with Radial Acquisition (PETRA) sequence using compressed sensing while preserving the image quality for high-resolution MRI of tissue with ultra-short T2∗ values. METHODS: Compressed sensing was introduced in the PETRA sequence (csPETRA) to accelerate the time-consuming single point acquisition of the k-space center data. Random undersampling was applied to achieve acceleration factors up to Acc = 32. Phantom and in vivo images of the knee joint of six volunteers were measured at 3T using csPETRA sequence with Acc = 4, 8, 12, 16, 24, and 32. Images were compared against fully sampled PETRA data (Acc = 1) for structural similarity and normalized-mean-square-error. Qualitative and semi-quantitative analyses were performed to assess the effect of the acceleration on image artifacts, image quality, and delineation of anatomical structures at the knee. RESULTS: Even at high acceleration factors of Acc = 16 no aliasing artifacts were observed, and the anatomical details were preserved compared with the fully sampled data. The normalized-mean-square-error was less than 1% for Acc = 16, in which single point imaging acquisition time was reduced from 165 to 10 s, reducing the total scan time from 7.8 to 5.2 min. Semi-quantitative analyses suggest that Acc = 16 yields comparable diagnostic quality as the fully sampled data for knee imaging at a scan time of 5.2 min. CONCLUSION: csPETRA allows for ultra-short T2∗ imaging of the knee joint in clinically acceptable scan times while maintaining the image quality of original non-accelerated PETRA sequence.

Sub-millisecond 2D MRI of the vocal fold oscillation using single-point imaging with rapid encoding.

OBJECTIVE: The slow spatial encoding of MRI has precluded its application to rapid physiologic motion in the past. The purpose of this study is to introduce a new fast acquisition method and to demonstrate feasibility of encoding rapid two-dimensional motion of human vocal folds with sub-millisecond resolution. METHOD: In our previous work, we achieved high temporal resolution by applying a rapidly switched phase encoding gradient along the direction of motion. In this work, we extend phase encoding to the second image direction by using single-point imaging with rapid encoding (SPIRE) to image the two-dimensional vocal fold oscillation in the coronal view. Image data were gated using electroglottography (EGG) and motion corrected. An iterative reconstruction with a total variation (TV) constraint was used and the sequence was also simulated using a motion phantom. RESULTS: Dynamic images of the vocal folds during phonation at pitches of 150 and 165 Hz were acquired in two volunteers and the periodic motion of the vocal folds at a temporal resolution of about 600 µs was shown. The simulations emphasize the necessity of SPIRE for two-dimensional motion encoding. DISCUSSION: SPIRE is a new MRI method to image rapidly oscillating structures and for the first time provides dynamic images of the vocal folds oscillations in the coronal plane.

A Novel GFDM Waveform Design Based on Cascaded WHT-LWT Transform for the Beyond 5G Wireless Communications.

In this paper, a new WHT-LWT-GFDM waveform obtained by combining Walsh-Hadamard Transform (WHT), Lifting Wavelet Transform (LWT), and Generalized Frequency Division Multiplexing (GFDM) is presented for use in next-generation wireless communication systems. The proposed approach meets the requirement of 5th-generation (5G) and beyond communication schemes in terms of low latency, low peak-to-average-power ratio (PAPR), and low bit-error rate (BER). To verify the performance of the presented waveform, PAPR and BER simulation results were obtained in additive white Gaussian noise (AWGN) and flat Rayleigh fading channels, and the performance of the proposed system was compared with conventional Orthogonal Frequency Division Multiplexing (OFDM), GFDM, and Walsh-Hadamard transform-based GFDM (WHT-GFDM). Simulation results show that the proposed waveform achieves the best BER and PAPR performances and it provides considerable performance gains over the conventional waveforms.

MR safety watchdog for active catheters: Wireless impedance control with real-time feedback.

PURPOSE: To dynamically minimize radiofrequency (RF)-induced heating of an active catheter through an automatic change of the termination impedance. METHODS: A prototype wireless module was designed that modifies the input impedance of an active catheter to keep the temperature rise during MRI below a threshold, ΔTmax . The wireless module (MR safety watchdog; MRsWD) measures the local temperature at the catheter tip using either a built-in thermistor or external data from a fiber-optical thermometer. It automatically changes the catheter input impedance until the temperature rise during MRI is minimized. If ΔTmax is exceeded, RF transmission is blocked by a feedback system. RESULTS: The thermistor and fiber-optical thermometer provided consistent temperature data in a phantom experiment. During MRI, the MRsWD was able to reduce the maximum temperature rise by 25% when operated in real-time feedback mode. CONCLUSION: This study demonstrates the technical feasibility of an MRsWD as an alternative or complementary approach to reduce RF-induced heating of active interventional devices. The automatic MRsWD can reduce heating using direct temperature measurements at the tip of the catheter. Given that temperature measurements are intrinsically slow, for a clinical implementation, a faster feedback parameter would be required such as the RF currents along the catheter or scattered electric fields at the tip.

Magnetic resonance imaging of the vocal fold oscillations with sub-millisecond temporal resolution.

PURPOSE: The temporal resolution of the MRI acquisition is intrinsically limited by the duration of the spatial encoding, which is typically on the order of milliseconds. Faster motion such as the vibration of the vocal folds during phonation cannot be imaged with conventional MRI as this would require sampling frequencies in the kilo-Hertz range. Here, a faster MRI acquisition strategy is presented that encodes a 1D periodic motion at a temporal resolution that is an order of magnitude higher compared to conventional MRI. METHODS: The proposed method encodes the position of an object moving along 1 dimension by applying very short phase encoding gradients along the same direction. This reduces the temporal resolution from the repetition time (TR) to the duration of the phase encoding gradients, which in this work was well below 1 ms. The technique is applied to the vocal fold oscillations and the position of the vocal folds is measured simultaneously using electroglottography (EGG). Simulations of the point spread function for regular encoding and the proposed method are performed as well. RESULTS: With this new phase, encoding strategy oscillations of the human vocal folds up to a frequency of 145 Hz could be dynamically imaged at 10 images per cycle. Simulations show the advantage of this method over conventional imaging of fast moving objects. CONCLUSION: A new method for MR imaging of fast moving spins is presented allowing a temporal resolution below 1 ms at a spatial resolution below 1 mm, circumventing TR as the limit for temporal resolution.

Publication Patterns of Presentations at the 16th Quadrennial Meeting of the World Society for Stereotactic and Functional Neurosurgery.

BACKGROUND: The quality of a scientific meeting can be quantified by the rate of full publications arising from the presented abstracts and the impact factor of the journals in which the studies were published. OBJECTIVES: The aim of this study was to investigate the publication rates of presentations from the 2013 World Society for Stereotactic and Functional Neurosurgery (WSSFN) quadrennial meeting. METHODS: Scopus and PubMed databases were searched for the authors of the presentations to identify full publications arising from the relevant abstracts. Author and content matching were used to match an abstract with a full publication. Mann-Whitney U and Kruskal-Wallis tests were used for statistical analysis. RESULTS: In total, 77% (57/74), 56% (44/79), and 50% (79/157) of the paper, flash, and poster presentations, respectively, have been published, with an overall publication rate of 58% (180/310). Articles received a total of 5,227 citations, with an average of 29 ± 64.1 citations per article. The first authors who published their studies had a significantly higher h-index than those who did not publish (p = 0.003). The most preferred journals for publication were Journal of Neurosurgery, Acta Neurochirurgica, and Stereotactic and Functional Neurosurgery. The majority of the articles (117/180 [65%]) were published in a quartile 1 or 2 journal. The average journal impact factor (JIF) was 4.5 for all presentations, and 7.8 for paper session presentations. Studies presented in paper sessions were published in significantly higher-impact factor journals than those presented in poster sessions (p < 0.001). CONCLUSIONS: The WSSFN Congress had a relatively high overall publication rate (58%) compared to both other neurosurgical congresses and congresses in other scientific fields. The average JIF of 7.8 is a reflection of the high quality and high impact of the paper session presentations.

Magnetic resonance imaging for pathobiological assessment and interventional treatment of the coronary arteries.

X-ray-based fluoroscopy is the standard tool for diagnostics and intervention in coronary artery disease. In recent years, computed tomography has emerged as a non-invasive alternative to coronary angiography offering detection of coronary calcification and imaging of the vessel lumen by the use of iodinated contrast agents. Even though currently available invasive or non-invasive techniques can show the degree of vessel stenosis, they are unable to provide information about biofunctional plaque properties, e.g. plaque inflammation. Furthermore, the use of radiation and the necessity of iodinated contrast agents remain unfavourable prerequisites. Magnetic resonance imaging (MRI) is a radiation-free alternative to X-ray which offers anatomical and functional imaging contrasts fostering the idea of non-invasive biofunctional assessment of the coronary vessel wall. In combination with molecular contrast agents that target-specific epitopes of the vessel wall, MRI might reveal unique plaque properties rendering it, for example, 'vulnerable and prone to rupture'. Early detection of these lesions may allow for early or prophylactic treatment even before an adverse coronary event occurs. Besides diagnostic imaging, advances in real-time image acquisition and motion compensation now provide grounds for MRI-guided coronary interventions. In this article, we summarize our research on MRI-based molecular imaging in cardiovascular disease and feature our advances towards real-time MRI-based coronary interventions in a porcine model.

La fluoroscopia con rayos X es la herramienta estándar para el diagnóstico y la intervención de coronariopatías. En los últimos años, la tomografía computarizada se ha convertido en una alternativa atraumática a la coronariografía, ya que se puede detectar la calcificación coronaria y ver a través de imágenes las luces de los vasos sanguíneos mediante el uso de medios de contraste yodados. Si bien las técnicas traumáticas o atraumáticas disponibles actualmente pueden mostrar el grado de la estenosis vascular, no pueden proporcionar información sobre las propiedades biofuncionales de la placa de ateroma, por ejemplo, inflamación de la placa de ateroma. Por otra parte, el uso de radiación y la necesidad de agentes de contraste yodados siguen siendo requisitos desfavorables. La resonancia magnética (RM) es una alternativa sin radiación a los rayos X que proporciona contrates de imagen con información anatómica y funcional, lo cual refuerza la idea del diagnóstico biofuncional atraumático de las paredes de los vasos coronarios. En combinación con medios de contraste molecular que actúan sobre epítopos específicos de las paredes de los vasos, la RM puede poner de manifiesto propiedades particulares de la placa de ateroma mediante su representación, por ejemplo, «vulnerabilidad y predisposición a rotura¼. La detección precoz de este tipo de lesiones puede facilitar un tratamiento a tiempo o preventivo antes de que tenga lugar una complicación coronaria grave.Además del diagnóstico por imagen, los avances en la adquisición de imágenes en tiempo real y la compensación del movimiento sirven de base para las intervenciones coronarias guiadas por RM. En este artículo, ofrecemos un resumen de nuestra investigación sobre imagen molecular con resonancia magnética en enfermedades cardiovasculares y presentamos nuestros avances hacia las intervenciones coronarias con RM en tiempo real en un modelo porcino.

It's the little things: On the complexity of planar electrode heating in MRI.

Neurological disorders are increasingly analysed and treated with implantable electrodes, and patients with such electrodes are studied with MRI despite the risk of radio-frequency (RF) induced heating during the MRI exam. Recent clinical research suggests that electrodes with smaller diameters of the electrical interface between implant and tissue are beneficial; however, the influence of this electrode contact diameter on RF-induced heating has not been investigated. In this work, electrode contact diameters between 0.3 and 4 mm of implantable electrodes appropriate for stimulation and electrocorticography were evaluated in a 1.5 T MRI system. In situ temperature measurements adapted from the ASTM standard test method were performed and complemented by simulations of the specific absorption rate (SAR) to assess local SAR values, temperature increase and the distribution of dissipated power. Measurements showed temperature changes between 0.8 K and 53 K for different electrode contact diameters, which is well above the legal limit of 1 K. Systematic errors in the temperature measurements are to be expected, as the temperature sensors may disturb the heating pattern near small electrodes. Compared to large electrodes, simulations suggest that small electrodes are subject to less dissipated power, but more localized power density. Thus, smaller electrodes might be classified as safe in current certification procedures but may be more likely to burn adjacent tissue. To assess these local heating phenomena, smaller temperature sensors or new non-invasive temperature sensing methods are needed.

Safety of active catheters in MRI: Termination impedance versus RF-induced heating.

PURPOSE: To investigate the effect of the termination impedance on the RF-induced heating of active catheters using analytical modeling. THEORY AND METHODS: Interaction of an arbitrary electric (E) field and an isolated transmission line (TL) embedded in cascaded lossy media was analytically modeled. Termination impedances at the tip and the input sides were expressed as distinct parameters in the current and voltage distribution formulae that are obtained by solving the inhomogeneous wave equations using the Green's function approach. The tip specific absorption rate (SAR) was calculated for different E field configurations. The tip SAR was displayed on a color-coded Smith chart in terms of the normalized input reflection coefficient. Results of the analytical calculations were compared to transfer function (TF) measurements. An input impedance control unit that is integrated to the interface circuit was introduced. RESULTS: TFs from analytical model and measurements exhibited similar behaviors. Color-coded Smith charts shows that the analytical model and measured TF-based tip SAR depends strongly on the input reflection coefficient. Both for measured and analytical TFs, SAR can deviate up to 70% from the mean value for different input impedance values. CONCLUSION: This study shows that it is possible to change the RF-induced heating characteristics of an active catheter by adjusting the input impedance, and the presented analytical model is in good agreement with TF measurements.

Direct estimation of 17 O MR images (DIESIS) for quantification of oxygen metabolism in the human brain with partial volume correction.

PURPOSE: To provide a data post-processing method that corrects for partial volume effects (PVE) and fast T 2 * decay in dynamic 17 O MRI for the mapping of cerebral metabolic rates of oxygen consumption (CMRO2 ). METHODS: CMRO2 is altered in neurodegenerative diseases and tumors and can be measured after 17 O gas inhalation using dynamic 17 O MRI. CMRO2 quantification is difficult because of PVE. To correct for PVE, a direct estimation of the MR images (DIESIS) method is proposed and used in 4 dynamic 17 O MRI data sets of a healthy volunteer acquired on a 3T MRI system. With DIESIS, 17 O MR signal time curves in selected regions were directly estimated based on parcellation of a coregistered 1 H MPRAGE image. RESULTS: Profile likelihood analysis of the DIESIS method showed identifiability of CMRO2 . In white matter (WM), DIESES reduced CMRO2 from 0.97 ± 0.25 µmol/gtissue /min with Kaiser-Bessel gridding reconstruction to 0.85 ± 0.21 µmol/gtissue /min, whereas in gray matter (GM) it increases from 1.3 ± 0.31 µmol/gtissue /min to 1.86 ± 0.36 µmol/gtissue /min; both values are closer to the literature values from the 15 O-PET studies. CONCLUSION: DIESIS provided an increased separation of CMRO2 values in GM and WM brain regions and corrected for partial volume effects in 17 O-MRI inhalation experiments. DIESIS could also be applied to more heterogeneous tissues such as glioblastomas if subregions of the tumor can be represented as additional parcels.

Optimization of acoustic radiation force imaging: Influence of timing parameters on sensitivity.

PURPOSE: Optimization of timing parameters for MR-guided ARFI to achieve the highest displacement signal-to-noise ratio (SNRd ). THEORY AND METHODS: In MR-guided ARFI the phase change induced by motion encoding gradients (MEGs) is measured to assess tissue displacement. The sensitivity of this encoding procedure depends on several timing parameters, such as the MEG duration and the offset time between ultrasound (US) and MEG. Furthermore, mechanical and MR tissue constants and MEG schemes (bipolar or three-lobed) influence SNRd . Optimal timing parameters were determined in simulations for bipolar and three-lobed MEGs, and the results were compared with measurements. To provide clinically usable timing parameters, physiologically relevant ranges of tissue constants were considered. RESULTS: For the considered ranges of tissue constants, optimal timing parameters provide only 6% higher SNRd for bipolar than for three-lobed MEG. Three-lobed MEG is less sensitive to motion as confirmed in phantom experiments. Bipolar MEG can use approximately 1.5-fold shorter MEG durations. CONCLUSION: Both bipolar and three-lobed MEGs can yield approximately the same SNRd if the optimal timing parameters are chosen. Bipolar MEG allows for shorter durations, which is preferable if deposition of US energy needs to be minimized, and three-lobed MEG is more suitable when residual motion compensation is necessary. Magn Reson Med 79:981-986, 2018. © 2017 International Society for Magnetic Resonance in Medicine.

Management Strategies for Hydrocephalus in Alobar Holoprosencephaly: A Case Report and Discussion.

Holoprosencephaly is a rare congenital malformation resulting from an impaired midline division of the prosencephalon into distinct cerebral hemispheres. Hydrocephalus is a frequent problem among the few survivors with alobar holoprosencephaly (aHPE), its most severe form. The literature about neurosurgical management of hydrocephalus in this condition is limited and dispersed, and there are still some points that need to be resolved. We report the case of a newborn with aHPE, hydrocephalus, and central diabetes insipidus. We delineate the complexity of the management of these patients and emphasize the benefits of using an initial programmable shunt valve. Further discussion about management strategies includes reviewing previous reports and the benefits of shunting for hypothalamic osmoreceptor function.

3D CMRO2 mapping in human brain with direct 17O MRI: Comparison of conventional and proton-constrained reconstructions.

Oxygen metabolism is altered in brain tumor regions and is quantified by the cerebral metabolic rate of oxygen consumption (CMRO2). Direct dynamic 17O MRI with inhalation of isotopically enriched 17O2 gas can be used to quantify CMRO2; however, pixel-wise CMRO2 quantification in human brain is challenging due to low natural abundance of 17O isotope and, thus, the low signal-to-noise ratio (SNR) of 17O MR images. To test the feasibility CMRO2 mapping at a clinical 3 T MRI system, a new iterative reconstruction was proposed, which uses the edge information contained in a co-registered 1H gradient image to construct a non-homogeneous anisotropic diffusion (AD) filter. AD-constrained reconstruction of 17O MR images was compared to conventional Kaiser-Bessel gridding without and with Hanning filtering, and to iterative reconstruction with a total variation (TV) constraint. For numerical brain phantom and in two in vivo data sets of one healthy volunteer, AD-constrained reconstruction provided 17O images with improved resolution of fine brain structures and resulted in higher SNR. CMRO2 values of 0.78 - 1.55µmol/gtissue/min (white brain matter) and 1.03 - 2.01µmol/gtissue/min (gray brain matter) as well as the CMRO2 maps are in a good agreement with the results of 15O-PET and 17O MRI at 7 T and at 9.4 T. In conclusion, the proposed AD-constrained reconstruction enabled calculation of 3D CMRO2 maps at 3 T MRI system, which is an essential step towards clinical translation of 17O MRI for non-invasive CMRO2 quantification in tumor patients.

Comparison of ultrashort echo time sequences for MRI of an ancient mummified human hand.

PURPOSE: To compare the three different short-echo time (TE) pulse sequences ultrashort echo time (UTE), point-wise encoding time reduction with radial acquisition (PETRA), and single point imaging (SPI) for MRI of ancient remains. METHODS: MRI of mummies is challenging due to the extremely low water content and the very short transverse relaxation times T2 *. To overcome the signal loss associated with the short T2 *, three pulse sequences with very short TEs were compared. MR images of an ancient mummified human hand were acquired at field strengths of 1.5 Tesla (T) and 3T using home-made solenoid Tx/Rx radiofrequency (RF) coils. RESULTS: In all MR images, tissues could be differentiated and anatomical structures such as bones and tendons were clearly identified. Skin with embalming resin was hyperintense in MRI, whereas it appeared iso-intense in computed tomography. PETRA has the highest signal to noise ratio. With UTE, short scan times and a homogeneous RF excitation can be achieved, and blurring is less pronounced than with PETRA. SPI shows no blurring artifacts; however, it requires long scan times. CONCLUSION: This work provided an initial analysis for the optimization of imaging protocols for paleoradiology studies with MRI, and, ultimately, for MRI of tissue with extremely short T2 *.