Assessment of the Variability of Human Exposure to Radiofrequency Electromagnetic Fields Arising from 5.9 GHz Vehicular Communication in Urban Environments.

This paper assessed the variability of radiofrequency exposure among road users in urban settings due to vehicle-to-vehicle (V2V) communication operating at 5.9 GHz. The study evaluated the absorbed dose of radiofrequencies using whole-body specific absorption rate (SAR) in human models spanning different age groups, from children to adults. To overcome limitations of previous studies, we developed a novel hybrid procedure that combines deterministic and stochastic approaches, enabling assessment across multiple urban layouts. Real urban conditions and varying propagation scenarios were considered in SAR calculations. By varying the road user's position within 1.5-300 m from transmitting cars, the SAR distribution was determined. Median SAR remained consistently low, around 0.70 mW/kg, even with multiple transmitting cars and multiple emitting antennas, using maximum power allowed in US (44.8 dBm). The 99th percentile of SAR distribution varied based on body mass, decreasing for heavier models (typically adults) and increasing with the number of transmitting cars and antennas. The highest absorbed dose (73 mW/kg) occurred in a child model. The SAR consistently remained below the 80 mW/kg limit for whole-body exposure to electromagnetic fields in the 100 kHz-300 GHz range.

Assessment of Children's Exposure to Intelligent Transport System 5.9 GHz Vehicular Connectivity Using Numerical Dosimetry.

This study investigates the radio-frequency electromagnetic field exposure (RF-EMF) levels in pedestrians generated by vehicular communication technology. We specifically investigated exposure levels in children of different ages and both genders. This study also compares the children's exposure levels generated by such technology with those of an adult investigated in our previous study. The exposure scenario consisted of a 3D-CAD model of a vehicle equipped with two vehicular antennas operating at 5.9 GHz, each fed with 1 W power. Four child models were analyzed near the front and back of the car. The RF-EMF exposure levels were expressed as the Specific Absorption Rate (SAR) calculated over the whole body and 10 g mass (SAR10g) of the skin and 1 g mass (SAR1g) of the eyes. The maximum SAR10g value of 9 mW/kg was found in the skin of the head of the tallest child. The maximum whole-body SAR was 0.18 mW/kg and was found in the tallest child. As a general result, it was found that children's exposure levels are lower than those of adults. All the SAR values are well below the limits recommended by the International Commission on Non-Ionizing Radiation Protection (ICNIRP) in the general population.

Assessment of SAR in Road-Users from 5G-V2X Vehicular Connectivity Based on Computational Simulations.

(1) Background: Cooperative Intelligent Transportation Systems (C-ITS) will soon operate using 5G New-Radio (NR) wireless communication, overcoming the limitations of the current V2X (Vehicle-to-Everything) wireless communication technologies and increasing road-safety and driving efficiency. These innovations will also change the RF exposure levels of pedestrians and road-users in general. These people, in fact, will be exposed to additional RF sources coming from nearby cars and from the infrastructure. Therefore, an exposure assessment of people in the proximity of a connected car is necessary and urgent. (2) Methods: Two array antennas for 5G-V2X communication at 3.5 GHz were modelled and mounted on a realistic 3D car model for evaluating the exposure levels of a human model representing people on the road near the car. Computational simulations were conducted using the FDTD solver implemented in the Sim4Life platform; different positions and orientations between the car and the human model were assessed. The analyzed quantities were the Specific Absorption Rate on the whole body (SARwb), averaged over 10 g (SAR10g) in specific tissues, as indicated in the ICNIRP guidelines. (3) Results: the data showed that the highest exposure levels were obtained mostly in the head area of the human model, with the highest peak obtained in the configuration where the main beam of the 5G-V2X antennas was more direct towards the human model. Moreover, in all configurations, the dose absorbed by a pedestrian was well below the ICNIRP guidelines to avoid harmful effects. (4) Conclusions: This work is the first study on human exposure assessment in a 5G-V2X scenario, and it expands the knowledge about the exposure levels for the forthcoming use of 5G in connected vehicles.

Assessment of EMF Human Exposure Levels Due to Wearable Antennas at 5G Frequency Band.

(1) Background: This work aims to assess human exposure to EMF due to two different wearable antennas tuned to two 5G bands. (2) Methods: The first one was centered in the lower 5G band, around f = 3.5 GHz, whereas the second one was tuned to the upper 5G band, at 26.5 GHz. Both antennas were positioned on the trunk of four simulated human models. The exposure assessment was performed by electromagnetic numerical simulations. Exposure levels were assessed by quantifying the specific absorption rate averaged on 10 g of tissue (SAR10g) and the absorbed power density (Sab), depending on the frequency of the wearable antenna. (3) Results: the higher exposure values that resulted were always mainly concentrated in a superficial area just below the antenna itself. In addition, these resulting distributions were narrowed around their peak values and tended to flatten toward lower values in farther anatomical body regions. All the exposure levels complied with ICNIRP guidelines when considering realistic input power. (4) Conclusions: This work highlights the importance of performing an exposure assessment when the antenna is placed on the human wearer, considering the growth of wearable technology and its wide variety of application, particularly regarding future 5G networks.

Road User Exposure from ITS-5.9 GHz Vehicular Connectivity.

This study addressed an important but not yet thoroughly investigated topic regarding human exposure to radio-frequency electromagnetic fields (RF-EMF) generated by vehicular connectivity. In particular, the study assessed, by means of computational dosimetry, the RF-EMF exposure in road users near a car equipped with vehicle-to-vehicle (V2V) communication antennas. The exposure scenario consisted of a 3D numerical model of a car with two V2V antennas, each fed with 1 W, operating at 5.9 GHz and an adult human model to simulate the road user near the car. The RF-EMF dose absorbed by the human model was calculated as the specific absorption rate (SAR), that is, the RF-EMF power absorbed per unit of mass. The highest SAR was observed in the skin of the head (34.7 mW/kg) and in the eyes (15 mW/kg); the SAR at the torso (including the genitals) and limbs was negligible or much lower than in the head and eyes. The SAR over the whole body was 0.19 mW/kg. The SAR was always well below the limits of human exposure in the 100 kHz-6 GHz band established by the International Commission on Non-Ionizing Radiation Protection (ICNIRP). The proposed approach can be generalized to assess RF-EMF exposure in different conditions by varying the montage/number of V2V antennas and considering human models of different ages.

Use of Machine Learning for the Estimation of Down- and Up-Link Field Exposure in Multi-Source Indoor WiFi Scenarios.

A novel Machine Learning (ML) method based on Neural Networks (NN) is proposed to assess radio-frequency (RF) exposure generated by WiFi sources in indoor scenarios. The aim was to build an NN capable of addressing the complexity and variability of real-life exposure setups, including the effects of not only down-link transmission access points (APs) but also up-link transmission by different sources (e.g. laptop, printers, tablets, and smartphones). The NN was fed with easy to be found data, such as the position and type of WiFi sources (APs, clients, and other users) and the position and material characteristics (e.g. penetration loss) of walls. The NN model was assessed using an additional new layout, distinct from that one used to build and optimize the NN coefficients. The NN model achieved a remarkable field prediction accuracy across exposure conditions in both layouts, with a median prediction error of -0.4 to 0.6 dB and a root mean square error of 2.5-5.1 dB, compared with the target electric field estimated by a deterministic indoor network planner. The proposed approach performs well for the different layouts and is thus generally used to assess RF exposure in indoor scenarios. © 2021 The Authors. Bioelectromagnetics published by Wiley Periodicals LLC on behalf of Bioelectromagnetics Society.

3D space-dependent models for stochastic dosimetry applied to exposure to low frequency magnetic fields.

In this study, an innovative approach that combines Principal Component Analysis (PCA) and Gaussian process regression (Kriging method), never used before in the assessment of human exposure to electromagnetic fields (EMF), was applied to build space-dependent surrogate models of the 3D spatial distribution of the electric field induced in central nervous system (CNS) of children of different ages exposed to uniform magnetic field at 50 Hz of 200 µT of amplitude with uncertain orientation. The 3D surrogate models showed very low normalized percentage mean square error (MSE) values, always lower than 0.16%, confirming the feasibility and accuracy of the approach in estimating the 3D spatial distribution of E with a low number of components. Results showed that the electric field values induced in CNS tissues of children were within the ICNIRP basic restrictions for general public, with 99th percentiles of the E values obtained for each orientation showing median values in the range 1.9-2.1 mV/m. Similar 3D spatial distributions of the electric fields were found to be induced in CNS tissues of children of different ages. Bioelectromagnetics. 9999:1-10, 2018. © 2019 Bioelectromagnetics Society.

Transcranial cerebellar direct current stimulation and transcutaneous spinal cord direct current stimulation as innovative tools for neuroscientists.

Two neuromodulatory techniques based on applying direct current (DC) non-invasively through the skin, transcranial cerebellar direct current stimulation (tDCS) and transcutaneous spinal DCS, can induce prolonged functional changes consistent with a direct influence on the human cerebellum and spinal cord. In this article we review the major experimental works on cerebellar tDCS and on spinal tDCS, and their preliminary clinical applications. Cerebellar tDCS modulates cerebellar motor cortical inhibition, gait adaptation, motor behaviour, and cognition (learning, language, memory, attention). Spinal tDCS influences the ascending and descending spinal pathways, and spinal reflex excitability. In the anaesthetised mouse, DC stimulation applied under the skin along the entire spinal cord may affect GABAergic and glutamatergic systems. Preliminary clinical studies in patients with cerebellar disorders, and in animals and patients with spinal cord injuries, have reported beneficial effects. Overall the available data show that cerebellar tDCS and spinal tDCS are two novel approaches for inducing prolonged functional changes and neuroplasticity in the human cerebellum and spinal cord, and both are new tools for experimental and clinical neuroscientists.

Dosimetric study of fetal exposure to uniform magnetic fields at 50 Hz.

In this paper, fetal exposure to uniform magnetic fields (MF) with different polarizations is quantified at 50 Hz. Numerical computations were performed on high-resolution pregnant models at 3, 7, and 9 months of gestational age (GA), that distinguish a high number of fetal tissues. Fetal whole-body and tissue-specific induced electric fields (E) and current densities (J) were analyzed as a function of both the extremely low frequency magnetic field (ELF-MF) polarization and GA. Additionally, the induced field variation due to changes in fetal position was analyzed by means of two new pregnant models. The uncertainty budget due to the grid resolution was also calculated. Finally, the compliance of the fetal exposure to the ICNIRP Guidelines was checked. A fetal exposure matrix was built at 50 Hz, which could be used to further investigate possible interaction mechanisms between ELF-MF and the associated health risk. Some specific findings were: (1) the induced fields increased with GA; (2) the maxima E were found in skin and fat tissues at each GA; (3) fetal tissue-specific exposure was modified as a function of GA and polarization; (4) the change of the fetal position in the womb significantly modified the induced E in some fetal tissues; (5) the induced fields were in compliance with ICNIRP Guidelines and the results were quite below the permitted threshold limit.

Modulating human procedural learning by cerebellar transcranial direct current stimulation.

Neuroimaging studies suggest that the cerebellum contributes to human cognitive processing, particularly procedural learning. This type of learning is often described as implicit learning and involves automatic, associative, and unintentional learning processes. Our aim was to investigate whether cerebellar transcranial direct current stimulation (tDCS) influences procedural learning as measured by the serial reaction time task (SRTT), in which subjects make speeded key press responses to visual cues. A preliminary modeling study demonstrated that our electrode montage (active electrode over the cerebellum with an extra-cephalic reference) generated the maximum electric field amplitude in the cerebellum. We enrolled 21 healthy subjects (aged 20-49 years). Participants did the SRTT, a visual analogue scale and a visual attention task, before and 35 min after receiving 20-min anodal and sham cerebellar tDCS in a randomized order. To avoid carry-over effects, experimental sessions were held at least 1 week apart. For our primary outcome measure (difference in RTs for random and repeated blocks) anodal versus sham tDCS, RTs were significantly slower for sham tDCS than for anodal cerebellar tDCS (p = 0.04), demonstrating that anodal tDCS influenced implicit learning processes. When we assessed RTs for procedural learning across the one to eight blocks, we found that RTs changed significantly after anodal stimulation (interaction "time" × "blocks 1/8": anodal, p = 0.006), but after sham tDCS, they remained unchanged (p = 0.094). No significant changes were found in the other variables assessed. Our finding that anodal cerebellar tDCS improves an implicit learning type essential to the development of several motor skills or cognitive activity suggests that the cerebellum has a critical role in procedural learning. tDCS could be a new tool for improving procedural learning in daily life in healthy subjects and for correcting abnormal learning in neuropsychiatric disorders.

Nonlinear heart rate variability measures under electromagnetic fields produced by GSM cellular phones.

This study was designed to assess the nonlinear dynamics of heart rate variability (HRV) during exposure to low-intensity EMFs. Twenty-six healthy young volunteers were subjected to a rest-to-stand protocol to evaluate autonomic nervous system in quiet condition (rest, vagal prevalence) and after a sympathetic activation (stand). The procedure was conducted twice in a double-blind design: once with a genuine EMFs exposure (GSM cellular phone at 900 MHz, 2 W) and once with a sham exposure (at least 24 h apart). During each session, three-lead electrocardiograms were recorded and RR series extracted off-line. The RR series were analyzed by nonlinear deterministic techniques in every phase of the protocol and during the different exposures. The analysis of the data shows there was no statistically significant effect due to GSM exposure on the nonlinear dynamics of HRV.

Monopolar tDCS might affect brainstem reflexes: A computational and neurophysiological study.

OBJECTIVE: To assess whether monopolar multi-electrode transcranial direct current stimulation (tDCS) montages might selectively affect deep brain structures through computational predictions and neurophysiological assessment. METHODS: Electric field distribution in deep brain structures (i.e., thalamus and midbrain) were estimated through computational models simulating tDCS with two monopolar and two monopolar multi-electrode montages. Monopolar multi-electrode tDCS was then applied to healthy subject, and effects on pontine and medullary circuitries was evaluated studying changes in blink reflex (BR) and masseter inhibitory reflex (MIR). RESULTS: Computational results suggest that tDCS with monopolar multi-electrode montages might induce electric field intensities in deep brain structure comparable to those in grey matter, while neurophysiological results disclosed that BR and MIR were selectively modulated by tDCS only when cathode was placed over the right deltoid. CONCLUSIONS: Multi-electrode tDCS (anodes over motor cortices, cathode over right deltoid) could induce significant electric fields in the thalamus and midbrain, and selectively affect brainstem neural circuits. SIGNIFICANCE: Multi-electrode tDCS (anodes over motor cortices, cathode over right deltoid) might be further explored to affect brainstem activity, also in the context of non-invasive deep brain stimulation.

Modeling Electric Fields in Transcutaneous Spinal Direct Current Stimulation: A Clinical Perspective.

Clinical findings suggest that transcutaneous spinal direct current stimulation (tsDCS) can modulate ascending sensitive, descending corticospinal, and segmental pathways in the spinal cord (SC). However, several aspects of the stimulation have not been completely understood, and realistic computational models based on MRI are the gold standard to predict the interaction between tsDCS-induced electric fields and anatomy. Here, we review the electric fields distribution in the SC during tsDCS as predicted by MRI-based realistic models, compare such knowledge with clinical findings, and define the role of computational knowledge in optimizing tsDCS protocols. tsDCS-induced electric fields are predicted to be safe and induce both transient and neuroplastic changes. This could support the possibility to explore new clinical applications, such as spinal cord injury. For the most applied protocol (2-3 mA for 20-30 min, active electrode over T10-T12 and the reference on the right shoulder), similar electric field intensities are generated in both ventral and dorsal horns of the SC at the same height. This was confirmed by human studies, in which both motor and sensitive effects were found. Lastly, electric fields are strongly dependent on anatomy and electrodes' placement. Regardless of the montage, inter-individual hotspots of higher values of electric fields were predicted, which could change when the subjects move from a position to another (e.g., from the supine to the lateral position). These characteristics underlines the need for individualized and patient-tailored MRI-based computational models to optimize the stimulation protocol. A detailed modeling approach of the electric field distribution might contribute to optimizing stimulation protocols, tailoring electrodes' configuration, intensities, and duration to the clinical outcome.

Electric field and current density distribution in an anatomical head model during transcranial direct current stimulation for tinnitus treatment.

Tinnitus is considered an auditory phantom percept. Recently, transcranial direct current stimulation (tDCS) has been proposed as a new approach for tinnitus treatment including, as potential targets of interest, either the temporal and temporoparietal cortex or prefrontal areas. This study investigates and compares the spatial distribution of the magnitude of the electric field and the current density in the brain tissues during tDCS of different brain targets. A numerical method was applied on a realistic human head model to calculate these field distributions in different brain structures, such as the cortex, white matter, cerebellum, hippocampus, medulla oblongata, pons, midbrain, thalamus, and hypothalamus. Moreover, the same distributions were evaluated along the auditory pathways. Results of this study show that tDCS of the left temporoparietal cortex resulted in a widespread diffuse distribution of the magnitude of the electric fields (and also of the current density) on an area of the cortex larger than the target brain region. On the contrary, tDCS of the dorsolateral prefrontal cortex resulted in a stimulation mainly concentrated on the target itself. Differences in the magnitude distribution were also found on the structures along the auditory pathways. A sensitivity analysis was also performed, varying the electrode position and the human head models. Accurate estimation of the field distribution during tDCS in different regions of the head could be valuable to better determine and predict efficacy of tDCS for tinnitus suppression.

Human Exposure Assessment to Wearable Antennas: Effect of Position and Interindividual Anatomical Variability.

(1) Background: This work aims to assess the human exposure to the RF-EMFs emitted by a wearable antenna. (2) Methods: a wearable antenna tuned at f = 2.45 GHz was tested by placing it in six realistic configurations relative to a male and female human model. The exposure assessment was performed by means of computational methods to estimate the SAR10g distributions at 1W of input power. (3) Results: (i) for all the configurations the SAR10g distributions resulted always mainly concentrated on a superficial area immediately below the antenna itself; (ii) the obtained values have shown that the configuration with the highest exposure value was when the antenna was posed on the arm; (iii) the exposure tends to be higher for male model. (4) Discussion and Conclusions: This work highlights the importance of performing an exposure assessment when the antenna is placed on the human wearer considering the growth of the wearable technology and its wide variety of fields of application, e.g., medical and military.

Exposure Assessment to Radiofrequency Electromagnetic Fields in Occupational Military Scenarios: A Review.

(1) Background: Radiofrequency radiations are used in most devices in current use and, consequently, the assessment of the human exposure to the radiofrequency radiations has become an issue of strong interest. Even if in the military field there is wide use of radiofrequency devices, a clear picture on the exposure assessment to the electromagnetic field of the human beings in the military scenario is still missing. (2) Methods: a review of the scientific literature regarding the assessment of the exposure of the military personnel to the RF specific to the military environment, was performed. (3) Results: the review has been performed grouping the scientific literature by the typology of military devices to which the military personnel can be exposed to. The military devices have been classified in four main classes, according to their intended use: communication devices, localization/surveillance devices, jammers and EM directed-energy weapons. (4) Discussion and Conclusions: The review showed that in the exposure conditions here evaluated, there were only occasional situations of overexposure, whereas in the majority of the conditions the exposure was below the worker exposure limits. Nevertheless, the limited number of studies and the lack of exposure assessment studies for some devices prevent us to draw definitive conclusions and encourage further studies on military exposure assessment.

Assessment of Human Exposure Levels Due to Mobile Phone Antennas in 5G Networks.

The recent deployment of 5G networks is bringing benefits to the population but it is also raising public concern about human RF-EMF exposure levels. This is particularly relevant considering the next 5G mobile devices, which are placed in close proximity to the subjects. Therefore, the aim of the following paper is focused on expanding the knowledge of the exposure levels in 5G exposure scenarios, specifically for mobile applications, using computational methods. The mobile antenna was designed considering the 5G technology innovations (i.e., mm-wave spectrum, beamforming capability, high gain and wide coverage), resulting in a phased-array antenna with eight elements at the working frequency of 27 GHz. To assess the exposure levels, different types of skin models with different grades of details and layers were considered. Furthermore, not only was the presence of a mobile phone user simulated, but also that of a person in their proximity, who could be hit by the main beam of the phased-array antenna. All the simulations were conducted in Sim4Life platform, where the exposure levels were assessed in terms of absorbed power density averaged over 4 cm2 and 1 cm2, following the ICNIRP guidelines. The results highlighted that the use of the homogeneous skin model led to the absorbed power density peaks being greatly underestimated, with respect to those obtained in multilayer skin models. Furthermore, interestingly, we found that the exposure levels obtained for the person passing nearby were slightly higher than those experienced by the mobile phone user himself. Finally, using the allowed input power for real mobile applications, all the values remained below the limits indicated by the ICNIRP guidelines.

Modeling of core-shell magneto-electric nanoparticles for biomedical applications: Effect of composition, dimension, and magnetic field features on magnetoelectric response.

The recent development of core-shell nanoparticles which combine strain coupled magnetostrictive and piezoelectric phases, has attracted a lot of attention due to their ability to yield strong magnetoelectric effect even at room temperature, thus making them a promising tool to enable biomedical applications. To fully exploit their potentialities and to adapt their use to in vivo applications, this study analyzes, through a numerical approach, their magnetoelectric behavior, shortly quantified by the magnetoelectric coupling coefficient (αME), thus providing an important milestone for the characterization of the magnetoelectric effect at the nanoscale. In view of recent evidence showing that αME is strongly affected by both the applied magnetic field DC bias and AC frequency, this study implements a nonlinear model, based on magnetic hysteresis, to describe the responses of two different core-shell nanoparticles to various magnetic field excitation stimuli. The proposed model is also used to evaluate to which extent realistic variables such as core diameter and shell thickness affect the electric output. Results prove that αME of 80 nm cobalt ferrite-barium titanate (CFO-BTO) nanoparticles with a 60:40 ratio is equal to about 0.28 V/cm∙Oe corresponding to electric fields up to about 1000 V/cm when a strong DC bias is applied. However, the same electric output can be obtained even in absence of DC field with very low AC fields, by exploiting the hysteretic characteristics of the same composites. The analysis of core and shell dimension is as such to indicate that, to maximize αME, larger core diameter and thinner shell nanoparticles should be preferred. These results, taken together, suggest that it is possible to tune magnetoelectric nanoparticles electric responses by controlling their composition and their size, thus opening the opportunity to adapt their structure on the specific application to pursue.

Modelling of magnetoelectric nanoparticles for non-invasive brain stimulation: a computational study.

Objective.Recently developed magnetoelectric nanoparticles (MENPs) provide a potential tool to enable different biomedical applications. They could be used to overcome the intrinsic constraints posed by traditional neurostimulation techniques, namely the invasiveness of electrodes-based techniques, the limited spatial resolution, and the scarce efficiency of magnetic stimulation.Approach.By using computational electromagnetic techniques, we modelled the behaviour of recently designed biocompatible MENPs injected, in the shape of clusters, in specific cortical targets of a highly detailed anatomical head model. The distributions and the tissue penetration of the electric fields induced by MENPs clusters in each tissue will be compared to the distributions induced by traditional transcranial magnetic stimulation (TMS) coils for non-invasive brain stimulation positioned on the left prefrontal cortex (PFC) of a highly detailed anatomical head model.Main results.MENPs clusters can induce highly focused electric fields with amplitude close to the neural activation threshold in all the brain tissues of interest for the treatment of most neuropsychiatric disorders. Conversely, TMS coils can induce electric fields of several tens of V m-1over a broad volume of the PFC, but they are unlikely able to efficiently stimulate even small volumes of subcortical and deep tissues.Significance.Our numerical results suggest that the use of MENPs for brain stimulation may potentially led to a future pinpoint treatment of neuropshychiatric disorders, in which an impairment of electric activity of specific cortical and subcortical tissues and networks has been assumed to play a crucial role.

Electric Fields Induced in the Brain by Transcranial Electric Stimulation: A Review of In Vivo Recordings.

Transcranial electrical stimulation (tES) techniques, such as direct current stimulation (tDCS) and transcranial alternating current stimulation (tACS), cause neurophysiological and behavioral modifications as responses to the electric field are induced in the brain. Estimations of such electric fields are based mainly on computational studies, and in vivo measurements have been used to expand the current knowledge. Here, we review the current tDCS- and tACS-induced electric fields estimations as they are recorded in humans and non-human primates using intracerebral electrodes. Direct currents and alternating currents were applied with heterogeneous protocols, and the recording procedures were characterized by a tentative methodology. However, for the clinical stimulation protocols, an injected current seems to reach the brain, even at deep structures. The stimulation parameters (e.g., intensity, frequency and phase), the electrodes' positions and personal anatomy determine whether the intensities might be high enough to affect both neuronal and non-neuronal cell activity, also deep brain structures.