Demineralization Inhibition by High-Speed Scanning of 9.3 µm CO2 Single Laser Pulses Over Enamel.

BACKGROUND AND OBJECTIVE: In vitro studies were conducted to evaluate the use of an automated system for high-speed scanning of single 9.3 µm CO2 laser pulses in the inhibition of caries-like lesion formation in the enamel of extracted human molars. The effect of the laser in generating an acid-resistant layer and the effect of the layer on inhibiting surface mineral loss during pH cycling was explored. STUDY DESIGN/MATERIALS AND METHODS: Laser irradiation was performed with fluences of 0.6, 0.8, and 1.0 J/cm2 for single pulses of 1 mm diameter (1/e2 ), with pulse durations of 17, 22, and 27 microseconds, respectively. The laser was scanned at a 750 Hz pulse repetition rate in an automated pattern covering an area of 7 mm2 in 0.3 sec. Six treatment groups were investigated: three groups for each fluence for laser-only and three for laser irradiation with additional fluoride from a toothpaste slurry (sodium fluoride at 1100 ppm). Each group used non-irradiated areas, which included untreated controls for the laser-only groups and a fluoride-only treatment for the groups with additional fluoride. pH cycling was performed on both groups, followed by microhardness testing to determine the relative mineral loss (∆Z) from a caries-like formation and surface mineral loss (∆S). RESULTS: Laser irradiation with the 9.3 µm CO2 laser generated an acid-resistant layer of about 15 µm in depth. For the laser-irradiated samples with additional fluoride application, the relative mineral loss (∆Z) was 113 ± 63 vol%-µm, while for those with only fluoride application ∆Z was 572 ± 172 vol%-µm. At the highest fluence (1.0 J/cm2 ) used, an 80.2% inhibition of caries-like lesion was measured by ∆Z. Using only laser irradiation at the highest fluence resulted in an inhibition of caries-like lesion of 79.5% for the irradiated samples (∆Z = 374 ± 149 vol%-µm) relative to the control (∆Z = 1826 ± 325 vol%-µm). Surface microhardness tests resulted in an inhibition of surface softening, as measured by the Knoop Hardness Value (KHN) (108 ± 33 KHN for laser irradiated with additional fluoride, for non-irradiated controls with fluoride only 52 ± 16 KHN). Inhibition of surface loss was observed for all laser fluences, but the maximum surface loss for the untreated control group was only 2.2 ± 0.49 µm. CONCLUSIONS: The results demonstrate a significant benefit of the 9.3 µm CO2 laser at fluences of 0.6, 0.8, and 1.0 J/cm2 in caries-like lesion inhibition as measured by the relative mineral loss in depth and surface mineral loss, without significant damage to the enamel. Additionally, inhibition of surface softening and surface loss during pH cycling was observed. The surface loss was small compared with the overall lesion depth and thickness of the generated acid-resistant layer. Lasers Surg. Med. © 2020 Wiley Periodicals LLC.

In situ Effect of CO2 Laser (9.3 µm) Irradiation Combined with AmF/NaF/SnCl2 Solution in Prevention and Control of Erosive Tooth Wear in Human Enamel.

OBJECTIVES: This single-blind, controlled crossover in situ study aimed to evaluate the effect of CO2 laser (9.3 µm) irradiation combined with AmF/NaF/SnCl2 solution on prevention and control of erosive tooth wear (ETW) in human enamel. MATERIALS AND METHODS: Two trial conditions were analyzed, condition 1 as ETW prevention (sound tooth surface) and condition 2 as ETW control (in vitro initial erosive lesion). The experiment was conducted in 2 phases, one with and one without exposure to AmF/NaF/SnCl2 solution. Hundred and ninety-two samples of human enamel (3 × 3 × 1 mm) were randomly divided into 4 experimental groups for each condition: C, without treatment (negative control); F, AmF/NaF/SnCl2 solution (positive control); L, CO2 laser irradiation; and L + F, CO2 laser + AmF/NaF/SnCl2 solution. Twelve volunteers used a removable device, each containing 8 samples per phase. Ex vivo erosive challenges (4 × 5 min/day) and rinsing protocol (1 × 30 s/day) were performed. The surface loss was determined using optical profilometer (n = 12 per group), and the surface morphology was observed with scanning electron microscopy (n = 3). RESULTS: In condition 1, data were analyzed by one-way ANOVA and condition 2 by two-way repeated-measures ANOVA, both with Tukey post hoc tests (α = 5%). In condition 1, groups L (4.59 ± 2.95 µm) and L + F (1.58 ± 1.24 µm) showed significantly less surface loss in preventing ETW than groups C and F. In condition 2, in controlling the progression of ETW, L + F was the only group with no significant surface loss between initial erosive lesion (3.65 ± 0.16 µm) and after erosive challenge (4.99 ± 1.17 µm). CONCLUSIONS: CO2 9.3-µm laser application prevented and controlled ETW progression in human enamel, with greater efficiency when combined with AmF/NaF/SnCl2 solution application.

Demineralization prevention with a new antibacterial restorative composite containing QASi nanoparticles: an in situ study.

OBJECTIVES: To investigate whether a newly developed dental composite with quaternary ammonium silica dioxide (QASi) nanoparticles incorporated with other fillers into the restorative material demonstrates antibacterial activity by reducing enamel demineralization in an in situ gap model. MATERIALS AND METHODS: Twenty subjects wearing a lower removable partial denture (RPD) with acrylic flanges on both sides of the mouth were recruited into the 4-week in situ study. The gap model consisted of an enamel slab placed next to a composite, separated by a 38-µm space. In the split-mouth design on one side of the RPD, the composite was the Nobio Infinix composite (Nobio Ltd., Kadima, Israel), and the contralateral side used a control composite. Each participant received enamel slabs from one tooth. The gap model was recessed into the RPD buccal flange, allowing microbial plaque to accumulate within the gap. After 4 weeks of continuous wearing, decalcification (∆Z mineral loss) of the enamel slabs adjacent to the gap was determined by cross-sectional microhardness testing in the laboratory. RESULTS: The ∆Z for the antibacterial composite test side was 235±354 (mean±standard deviation [SD]; data reported from 17 participants) and statistically significantly lower compared to ∆Z of the control side (774±556; mean±SD) (paired t-test, P<0.0001; mean of test minus control -539 (SD=392), 95% confidence interval of difference: -741, -338). CONCLUSIONS: This in situ clinical study showed that composites with QASi antibacterial particles significantly reduced demineralization in enamel adjacent to a 38-µm gap over a 4-week period in comparison to a conventional composite. CLINICAL RELEVANCE: Composites with QASi nanoparticle technology have the potential to reduce the occurrence of secondary caries. TRIAL REGISTRATION: ClinicalTrials.gov #NCT04059250.

Fissure caries inhibition with a CO2 9.3-µm short-pulsed laser-a randomized, single-blind, split-mouth controlled, 1-year clinical trial.

OBJECTIVES: The objective of this randomized, single-blind, split-mouth controlled, clinical trial was to evaluate whether the use of a short-pulsed 9.3-µm CO2 laser increases the caries resistance of occlusal pit and fissures in addition to fluoride therapy over 12 months. MATERIALS AND METHODS: A total of 60 participants, average age 13.1 years, were enrolled. At baseline, second molars were randomized into test and control, and assessed by ICDAS, SOPROLIFE, and DIAGNOdent. An independent investigator irradiated test molars with a CO2 laser (wavelength 9.3 µm, pulse duration 4 µs, pulse repetition rate 43 Hz, beam diameter 250 µm, average fluence 3.9 J/cm2, 20 laser pulses per spot). Test molars received laser and fluoride treatment, control teeth fluoride alone. Fluoride varnish was applied at baseline and at 6 months. After 6 and 12 months, teeth were again assessed. RESULTS: A total of 57 participants completed the 6-month and 51 the 12-month recall. Laser-treated surfaces showed very slight ICDAS improvements over time with ICDAS change - 1 in 11% and 8%, no changes (ICDAS change 0) in 68% and 67%, and slightly worsened (ICDAS change 1) in 19% and 24% at 6- and 12-month recalls, respectively, and worsened by two scores in 2% at both recall time points. Control teeth showed significantly higher ICDAS increases, with 47% and 25% showing ICDAS change 0, ICDAS change 1 in 49% and 55%, and ICDAS change 2 in 4% and 20% at 6- and 12-month recalls, respectively. Differences in ICDAS changes between the groups were statistically significant (P = 0.0002 and P < 0.0001; Wilcoxon's signed-rank test, exact). A total of 22% of the participants developed ICDAS 3 scores on the control teeth. CONCLUSIONS: Microsecond short-pulsed 9.3-µm CO2 laser irradiation markedly inhibits caries progression in pits and fissures in comparison with fluoride varnish alone. CLINICAL RELEVANCE: The 9.3-µm CO2 laser irradiation of pits and fissures enhances caries resistance. TRIAL REGISTRATION: ClinicalTrials.gov identifier: NCT02357979.

In vitro CO2 9.3-µm short-pulsed laser caries prevention-effects of a newly developed laser irradiation pattern.

Caries prevention with different lasers has been investigated in laboratory studies and clinical pilot trials. Objective of this in vitro study was to assess whether 9.3-µm microsecond short-pulsed CO2 laser irradiation enhances enamel caries resistance without melting, with and without additional fluoride application. Seven groups of enamel, totaling 105 human enamel samples, were irradiated with 2 different carbon dioxide lasers with 2 different energy application systems (original versus spread beam; 9.3 µm wavelength, pulse repetition rate 43 Hz vs 100 Hz, fluence ranges from 1.4 to 3.9 J/cm2, pulse duration 3 µs to 18 µs). The laboratory pH-cycling was performed with or without additional fluoride, followed by cross-sectional microhardness testing. To assess caries inhibition, the mean relative mineral loss delta Z (∆Z) was determined. To evaluate for melting, scanning electron microscopy (SEM) examinations were performed. For the non-laser control groups with additional fluoride use, the relative mineral loss (ΔZ, vol% × µm) ranged between 512 ± 292 and 809 ± 297 (mean ± SD). ΔZ for the laser-irradiated samples with fluoride use ranged between 186 ± 214 and 374 ± 191, averaging a 58% ± 6% mineral loss reduction (ANOVA, P < 0.01 to P < 0.0001). For the non-laser-treated controls without additional fluoride, the mineral loss increased (ΔZ 914 ± 422 to 1224 ± 736). In contrast, the ΔZ for the laser-treated groups without additional fluoride ranged between 463 ± 190 and 594 ± 272 (P < 0.01 to P < 0.001) indicative of 50% ± 2% average reduction in mineral loss. Enhanced caries resistance was achieved by all applied fluences. Using the spread beam resulted in enhanced resistance without enamel melting as seen by SEM. CO2 9.3-µm short-pulsed laser irradiation with both laser beam configurations resulted in highly significant reduction in enamel mineral loss. Modifying the beam to a more homogenous profile will allow enamel caries resistance even without apparent enamel melting.

Caries Management by Risk Assessment: Results from a Practice-Based Research Network Study.

Thirty dentists with clinical practices outside of a university setting were trained and calibrated successfully in DMFS and ICDAS-scoring. This randomized, controlled, parallel-arm, double-blind 2-year clinical trial with individual-level caries risk assignment of 460 patients to standard of care as control versus active CAMBRA treatment as intervention demonstrated that caries risk level, as well as caries disease indicators, were significantly reduced in the CAMBRA intervention group compared to the controls at all recall time points.

MI Varnish and MI Paste Plus in a caries prevention and remineralization study: a randomized controlled trial.

OBJECTIVES: White spot lesions (WSLs) are a complication of orthodontic therapy. This study investigated the effect of MI (minimally invasive) Paste Plus (MIPP) and MI Varnish (MIV) on WSLs in orthodontic patients during a 12-month, randomized, single-blind, prospective, standard-of-care controlled clinical trial. MATERIALS AND METHODS: Forty subjects, recruited from the UCSF School of Dentistry Orthodontics Clinic, were randomly assigned to the experimental (twice-daily 1100 ppm fluoride toothpaste, daily MIPP, quarterly MIV application) or control group (twice-daily 1100 ppm fluoride toothpaste, fluoride rinse recommendation). Facial surfaces of incisors, canines, and first bicuspids were evaluated at baseline, 3, 6, and 12 months using the enamel decalcification index (EDI) and the international caries detection and assessment system (ICDAS). RESULTS: Findings from 37 subjects are reported. At 12 months, teeth receiving experimental treatment were at lower but not significantly different odds of increased EDI scores (odds ratio, OR 0.63; intra-patient cluster-adjusted 95% CI 0.43, 1.18) and not associated with increased ICDAS scores (OR 0.99; 95% CI 0.64, 1.54). There was no statistically significant difference in mean patient-level EDI sum (experimental group 40.2; control 41.3; t test p = 0.80), ICDAS score (experimental 22.3; control 22.6; Mann-Whitney U test p = 0.80), or percentage of scored surfaces with ICDAS > 0 (experimental 54.6%; control 55.2%; t test p = 0.88). Salivary fluoride levels were significantly higher at 12 months for the experimental than for the control group (0.20 ± 0.26 versus 0.04 ± 0.04 ppm, Mann-Whitney U test p < 0.01). CONCLUSIONS: Applying daily MIPP and quarterly MIV resulted in no statistically significant differences in EDI sum and ICDAS scores. Higher salivary fluoride levels in the experimental group suggest that MIPP and MIV effectively deliver fluoride when used clinically. CLINICAL RELEVANCE: Daily MIPP and quarterly MIV applications do not appear to reduce significantly WSLs incidence during fixed orthodontic treatment.

Calibration of dentists for Caries Management by Risk Assessment Research in a Practice Based Research Network - CAMBRA PBRN.

BACKGROUND: To prove that Caries Management by Risk Assessment (CAMBRA) can be successfully implemented in dental practices outside of the university setting, dentists in the San Francisco Bay Area (CA) were approached to participate in a Practice Based Research Network (PBRN) study. The overall goal of the CAMBRA-PBRN study was to recruit 30 dentists to perform a two-year study involving approximately 900 patients. Goal of the calibration study was to standardize and calibrate dentists potentially participating in the CAMBRA-PBRN study. METHODS: To minimize inter-examiner variability in data collection, including classification of carious lesions and recording of existing restorations, participating dentists were trained and calibrated in accurate DMFS (decayed, missing, filled surfaces) charting. Dentists were also trained and calibrated to diagnose and differentiate between sound surfaces and non-cavitated caries lesions (International Caries Detection and Assessment - ICDAS scores 1 and 2) for posterior occlusal surfaces. Thirty dentists were calibrated to a single gold standard examiner (BJ) during 6 calibration sessions, between 2011 and 2014. Kappa statistics were used to determine inter-examiner reliability on 13 or more patients, aged 12-63 (average age 38 ± 15 years), per examiner during each session, resulting in 94 patient encounters over the course of all 6 sessions. To participate in the main study, examiners needed to achieve a minimum required kappa of 0.75. During the calibration process, examiners scored between 1036 and 2220 tooth surfaces. RESULTS: The kappa values (unweighted kappa) of the participating dentists compared to the gold standard examiner ranged from 0.75 to 0.90, with an average kappa of 0.84 ± 0.03. 90% of the examiners achieved overall kappa values above 0.8. However, separate reliability for assessment of non-cavitated lesions, as in other studies, was lower (0.55 ± 0.15). Multiple subcategories were evaluated. All dentists reached sufficient reliability values to proceed into the study; nevertheless, one dentist discontinued with the study due to scheduling conflicts. CONCLUSIONS: The high inter-examiner reliability results have shown that dentists who work in primarily non-research based practices can be effectively standardized and calibrated in data collection, based on specific guidelines created to anticipate potential research study scenarios.

Bond strength of etch-and-rinse and self-etch adhesive systems to enamel and dentin irradiated with a novel CO2 9.3 µm short-pulsed laser for dental restorative procedures.

The objective of this study was to evaluate the influence of CO2 9.3 µm short-pulsed laser irradiation on the shear bond strength of composite resin to enamel and dentin. Two hundred enamel and 210 dentin samples were irradiated with a 9.3 µm carbon dioxide laser (Solea, Convergent Dental, Inc., Natick, MA) with energies which either enhanced caries resistance or were effective for ablation. OptiBond Solo Plus [OptiBondTE] (Kerr Corporation, Orange, CA) and Peak Universal Bond light-cured adhesive [PeakTE] (Ultradent Products, South Jordan, UT) were used. In addition, Scotchbond Universal [ScotchbondSE] (3M ESPE, St. Paul, MN) and Peak SE self-etching primer with Peak Universal Bond light-cured adhesive [PeakSE] (Ultradent Products) were tested. Clearfil APX (Kuraray, New York, NY) was bonded to the samples. After 24 h, a single plane shear bond test was performed. Using the caries preventive setting on enamel resulted in increased shear bond strength for all bonding agents except for self-etch PeakSE. The highest overall bond strength was seen with PeakTE (41.29 ± 6.04 MPa). Etch-and-rinse systems achieved higher bond strength values to ablated enamel than the self-etch systems did. PeakTE showed the highest shear bond strength with 35.22 ± 4.40 MPa. OptiBondTE reached 93.8% of its control value. The self-etch system PeakSE presented significantly lower bond strength. The shear bond strength to dentin ranged between 19.15 ± 3.49 MPa for OptiBondTE and 43.94 ± 6.47 MPa for PeakSE. Etch-and-rinse systems had consistently higher bond strength to CO2 9.3 µm laser-ablated enamel. Using the maximum recommended energy for dentin ablation, the self-etch system PeakSE reached the highest bond strength (43.9 ± 6.5 MPa).

Caries inhibition with a CO2 9.3 µm laser: An in vitro study.

BACKGROUND AND OBJECTIVES: The caries preventive effects of different laser wavelengths have been studied in the laboratory as well as in pilot clinical trials. The objective of this in vitro study was to evaluate whether irradiation with a new 9.3 µm microsecond short-pulsed CO2 -laser could enhance enamel caries resistance with and without additional fluoride applications. STUDY DESIGN/MATERIALS AND METHODS: One hundred and one human tooth enamel samples were divided into seven groups. Each group was treated with different laser parameters (CO2 -laser, wavelength 9.3 µm, 43 Hz pulse-repetition rate, pulse duration between 3 µs at 1.5 mJ/pulse to 7 µs at 2.9 mJ/pulse). A laboratory pH-cycling model followed by cross-sectional microhardness testing determined the mean relative mineral loss delta Z (ΔZ) for each group to assess caries inhibition in tooth enamel by the CO2 9.3 µm short-pulsed laser irradiation. The pH-cycling was performed with or without additional fluoride. RESULTS: The non-laser control groups with additional fluoride had a relative mineral loss (ΔZ, vol% × µm) that ranged between 646 ± 215 and 773 ± 223 (mean ± SD). The laser irradiated and fluoride treated samples had a mean ΔZ ranging between 209 ± 133 and 403 ± 245 for an average 55% ± 9% reduction in mineral loss (ANOVA test, P < 0.0001). Increased mean mineral loss (ΔZ between 1166 ± 571 and 1339 ± 347) was found for the non-laser treated controls without additional fluoride. In contrast, the laser treated groups without additional fluoride showed a ΔZ between 470 ± 240 and 669 ± 209 (ANOVA test, P < 0.0001) representing an average 53% ± 11% reduction in mineral loss. Scanning electron microscopical assessment revealed that 3 µs pulses did not markedly change the enamel surface, while 7 µs pulses caused some enamel ablation. CONCLUSION: The CO2 9.3 µm short-pulsed laser energy renders enamel caries resistant with and without additional fluoride use. The observed enhanced acid resistance occurred with the laser irradiation parameters used without obvious melting of the enamel surface as well as after irradiation with energies causing cutting of the enamel. Lasers Surg. Med. 48:546-554, 2016. Published 2016. This article is a U.S. Government work and is in the public domain in the USA.

Performance of a light fluorescence device for the detection of microbial plaque and gingival inflammation.

OBJECTIVES: The hypothesis to be tested was that using the SOPROCARE system in fluorescence perio-mode allows scoring of microbial plaque that is comparable to the Turesky modification of the Quigley Hein plaque index (T-QH) and scoring of gingival inflammation comparable to the Silness and Löe gingival inflammation index (GI). MATERIALS AND METHODS: Fifty-five subjects with various amounts of microbial plaque were recruited. The T-QH and GI index were recorded. SOPROCARE pictures were recorded in fluorescence perio-mode and in daylight mode. Finally, conventional digital photographs were taken. All pictures were assessed using the same criteria as described for the clinical indices. RESULTS: The average T-QH was 1.1 ± 1.2 (mean ± SD). Scoring with SOPROCARE perio-mode led to a slightly higher average than the T-QH scores. SOPROCARE daylight mode and digital photography showed the highest plaque scores. The average GI index was 0.7 ± 0.9. SOPROCARE in perio-mode scored slightly lower. Linear regression fits between the different clinical indices and SOPROCARE scores were significantly different from zero demonstrating high goodness of fit. CONCLUSIONS: The study demonstrated that the SOPROCARE fluorescence assessment tool in perio-mode allows reliable judgment of microbial plaque and gingival inflammation levels similar to the established Turesky-modified Quigley Hein index and the Silness and Löe gingival inflammation index. Training on plaque-free teeth will actually reduce scoring errors. CLINICAL RELEVANCE: The SOPROCARE fluorescence tool in perio-mode provides reliable evaluation of microbial plaque and gingival inflammation for the dental clinician.

Laser all-ceramic crown removal-a laboratory proof-of-principle study-phase 2 crown debonding time.

BACKGROUND AND OBJECTIVES: The removal of all-ceramic crowns is a time consuming procedure in the dental office. Little research has been done in alternative removal techniques for all-ceramic crowns. The objective of the second phase of this proof-of-principle laboratory pilot study was to evaluate whether Ivoclar Vivadent all-ceramic crowns can be efficiently removed from natural teeth without damage to the underlying tooth structure using an Erbium laser. STUDY DESIGN/MATERIALS AND METHODS: The ceramic materials used were IPS E.max CAD Lithium-disilicate (LS2 ) (E.max CAD) and IPS E.max ZirCAD Zirconium-oxide (ZrO2 ) (ZirCAD) (Ivoclar, Vivadent, Liechtenstein). Molars, either as stand-alone teeth or placed in an artificial row of teeth, were prepared to receive all-ceramic crowns. Copings and full contour crowns with either featheredge or regular margins were produced. The all-ceramic crowns were bonded to the teeth with Ivoclar Multilink Automix. The time for Er:YAG laser debonding of each crown was then measured. The Er:YAG (LiteTouch, Syneron, Yokneam, Israel) was used with an 1,100 µm diameter fiber tip with energies up to 600 mJ per pulse (wavelength 2,940 nm, 10 Hz repetition rate, pulse duration 100 µs at 126 mJ/pulse, and 400 µs at 590 mJ/pulse). The irradiation was applied at a distance of 10 mm from the crown surface following a defined pattern. Air-water spray was applied to the crowns at a rate of 67 ml/minute. RESULTS: All of the all-ceramic crowns were successfully debonded with the laser. On average, an all-ceramic E.max CAD crown was debonded in 190 ± 92 seconds (average ± SD). The debonding time for ZirCAD featheredge crowns was 226 ± 105 seconds and for ZirCAD crowns with regular margins it was 312 ± 102 seconds. No crowns fractured and no damage to the underlying dentin was detected. The bonding cement deteriorated due to the Er:YAG irradiation. Additionally, no carbonization at the dentin/cement interface was observed. CONCLUSION: Er:YAG laser energy can successfully be used to efficiently debond all-ceramic full contour crowns from natural teeth without damage to the underlying tooth structure. Lasers Surg. Med. 46:636-643, 2014. © 2014 Wiley Periodicals, Inc.

Laser all-ceramic crown removal-a laboratory proof-of-principle study-phase 1 material characteristics.

BACKGROUND AND OBJECTIVES: The removal of all-ceramic crowns is a time consuming and destructive procedure in the dental office. The removal of all-ceramic crowns using Er:YAG lasers has not been previously described in the scientific literature. The objective of this laboratory proof-of-principle study was to evaluate whether with regards to absorption and transmission characteristics of bonding cements and ceramics all-ceramic crowns can be removed from natural teeth using an Erbium laser. STUDY DESIGN/MATERIALS AND METHODS: The Fourier Transform Infrared Spectroscopy (FTIR) was used on flat ceramic samples (IPS Empress Esthetic (EE), E.max CAD, and E.max ZirCAD) to assess which infrared laser wavelengths transmit through the ceramics. Additionally, FTIR spectra for four bonding cements (Variolink Veneer, Variolink II, Multilink Automix, and SpeedCEM) were obtained. The Er:YAG laser energy transmission (wavelength 2,940 nm, 10 Hz repetition rate, pulse duration 100 µs at 126 mJ/pulse to 300 µs at 508 mJ/pulse) through different ceramic thicknesses was measured. Ablation thresholds for bonding cements were determined. Cement samples were directly irradiated or laser light was transmitted through ceramic samples. RESULTS: While the ceramics did not show any characteristic water absorption bands in the FTIR, all bonding cements showed a broad H2 O/OH absorption band. Some cements exhibited a distinct absorption peak at the Er:YAG laser emission wavelength. Depending on the ceramic thickness, EE and E.max CAD ceramics transmitted between 21 and 60% of the incident Er:YAG energy, with E.max CAD transmitting more energy than EE at comparable thicknesses. In contrast, E.max ZirCAD transmitted only 5-10% of the incident energy. Initial signs of cement deterioration occurred at 1.3-2.6 J/cm(2) . Multilink Automix, SpeedCEM, and Variolink II started ablation at 4.4-4.7 J/cm(2) . Variolink Veneer needed 44% less energy for ablation. CONCLUSION: Er:YAG laser energy can be transmitted through all-ceramic materials and those transmitted energies are sufficient for ablation of bonding cements.

In-vivo occlusal caries prevention by pulsed CO2 -laser and fluoride varnish treatment--a clinical pilot study.

BACKGROUND AND OBJECTIVES: High caries prevalence in occlusal pits and fissures warrants novel prevention methods. An 86% reduction in dental enamel smooth surface demineralization in-vivo following short-pulsed 9.6 µm-CO(2) -laser irradiation was recently reported. The objective of this study was to conduct a blinded 12-month-pilot clinical trial of occlusal pit and fissure caries inhibition using the same CO(2) -laser irradiation conditions. STUDY DESIGN/MATERIALS AND METHODS: Twenty subjects, average age 14 years, were recruited. At baseline, second molars were randomized into test and control groups, assessed by International Caries Detection & Assessment System (ICDAS-II), SOPROLIFE light-induced fluorescence evaluator in daylight and blue-fluorescence mode and DIAGNOdent. An independent investigator irradiated test molars with a CO(2) -laser, wavelength 9.6 µm, pulse-duration 20 µs, pulse-repetition-rate 20 Hz, beam diameter 800 µm, average fluence 4.5 ± 0.5 J/cm(2), 20 laser pulses per spot. At 3-, 6- and 12-month recall teeth were assessed by ICDAS, SOPROLIFE and DIAGNOdent. All subjects received fluoride varnish applications at baseline and 6-month recall. RESULTS: All subjects completed the 3-month, 19 the 6-month and 16 the 12-month recall. At all recalls average ICDAS scores had decreased for the test and increased for the control fissures (laser vs. control, 3-month: -0.10 ± 0.14, 0.30 ± 0.18, P > 0.05; 6-month: -0.26 ± 0.13, 0.47 ± 0.16, P = 0.001; 12-month: -0.31 ± 0.15, 0.75 ± 0.17, P < 0.0001; mean ± SE, unpaired t-test) being statistically significantly different at 6- and 12-month recalls. SOPROLIFE daylight evaluation revealed at 6- and 12-months statistically significant differences in changes between baseline and recall for test and control molars, respectively (laser vs. control, 6-month: 0.22 ± 0.13, 0.17 ± 0.09, P = 0.02; 12-month: 0.28 ± 0.19, 0.25 ± 0.17, P = 0.03). For SOPROLIFE blue-fluorescence evaluation mean changes in comparison to baseline for the control and the laser treated teeth were also statistically significant for the 6- and 12-month recall. CONCLUSION: Specific microsecond short-pulsed 9.6 µm CO(2) -laser irradiation markedly inhibits caries progression in pits and fissures in comparison to fluoride varnish alone over 12 months.

Gastroesophageal reflux is not associated with dental erosion in children.

BACKGROUND & AIMS: Dental erosion is a complication of gastroesophageal reflux (GER) in adults; in children, it is not clear if GER has a role in dental pathologic conditions. Dietary intake, oral hygiene, high bacterial load, and decreased salivary flow might contribute independently to GER development or dental erosion, but their potential involvement in dental erosion from GER is not understood. We investigated the prevalence of dental erosion among children with and without GER symptoms, and whether salivary flow rate or bacterial load contribute to location-specific dental erosion. METHODS: We performed a cross-sectional study of 59 children (ages, 9-17 y) with symptoms of GER and 20 asymptomatic children (controls); all completed a questionnaire on dietary exposure. Permanent teeth were examined for erosion into dentin, erosion locations, and affected surfaces. The dentist was not aware of GER status, and the gastroenterologist was not aware of dental status. Stimulated salivary flow was measured and salivary bacterial load was calculated for total bacteria, Streptococcus mutans, and Lactobacilli. RESULTS: Controlling for age, dietary intake, and oral hygiene, there was no association between GER symptoms and dental erosion by tooth location or affected surface. Salivary flow did not correlate with GER symptoms or erosion. Erosion location and surface were independent of total bacteria and levels of Streptococcus mutans and Lactobacilli. CONCLUSIONS: Location-specific dental erosion is not associated with GER, salivary flow, or bacterial load. Prospective studies are required to determine the pathogenesis of GER-associated dental erosion and the relationship between dental caries to GER and dental erosion.

Caries detection using light-based diagnostic tools.

Modern caries treatment concepts like caries management by risk assessment--CAMBRA--entail diagnosing early caries lesions in a precavitated stage to make it possible to reverse the caries process with remineralization and bacteria reduction efforts. Newer, sensitive caries diagnostic tools can serve not only for early detection but also for monitoring of caries lesions to confirm the success of prevention and remineralization efforts. This article describes light-based caries diagnostic tools, with emphasis on fluorescence-based techniques, and compares the most common available fluorescence-based tools with a standardized visual caries inspection system-the International Caries Detection and Assessment System (ICDAS II). Fluorescence tools that provide high-resolution fluorescence pictures are likely to provide more reliable scores than fluorescence devices that assess via a single spot. The better visibility of the high-resolution fluorescence imaging could prevent unnecessary operative interventions.

Er:YAG laser debonding of porcelain veneers.

BACKGROUND AND OBJECTIVES: The removal of porcelain veneers using Er:YAG lasers has not been previously described in the scientific literature. This study was designed to systematically investigate the efficacy of an Er:YAG laser on veneer debonding, possibly without damage to the underlying tooth, and preservation of the veneer integrity. STUDY DESIGN/MATERIALS AND METHODS: The Fourier Transform Infrared Spectroscopy was used on 10 flat veneer samples (IPS Empress Esthetic, e.max Press HT) to assess which infrared laser wavelengths transmits through a veneer. Additionally, Fourier Transform Infrared (FTIR) spectra for a bonding cement (RelyX) were obtained. Consequently, Er:YAG laser energy transmission (wavelength 2,940 nm, 10 Hz repetition rate, pulse duration 100 µseconds at 133 mJ/pulse) through different veneer thicknesses was measured. Twenty-four veneers were bonded to freshly extracted and prepared incisors. The energy necessary for debonding was determined and then the veneers were debonded with the laser. Time needed for total debonding was measured and possible damage to the underlying tooth structure was assessed by light microscopy. RESULTS: While the veneer materials did not show any characteristic water absorption bands in the FTIR, the bonding cement showed a broad H(2) O/OH absorption band. The veneers transmitted between 11.5% and 43.7% of the incident Er:YAG energy with Emax transmitting twice the energy as EE at comparable thicknesses. Initial signs of cement ablation occurred at 1.8-4.0 J/cm(2) with the fiber tip positioned at a distance of 3-6 mm from the veneer surface and 133 mJ output energy. All 24 bonded veneers were completely removed with an average removal time of 113 ± 76 seconds. Underlying tooth structure was not damaged. The debonding mainly occurred at the cement/veneer interface. None of the Emax veneers fractured during debonding, while 36% of the EE did. CONCLUSION: Er:YAG laser irradiation effectively debonds porcelain veneers while preserving tooth structure. Maintaining veneer integrity possibly depends on the flexure strength of the veneer porcelain.

A Comparison of Four Caries Risk Assessment Methods.

Introduction: Caries risk assessment (CRA) is essential as the basis for successful management of dental caries. Of the many published CRA tools, four well-known ones are CAMBRA, Cariogram, American Dental Association (ADA), and American Academy of Pediatric Dentistry (AAPD) CRAs. The predictive accuracy of CAMBRA and Cariogram CRA tools have been examined in clinical outcomes studies in thousands of patients and the tools are widely used all over the world. The purpose of the present paper is three-fold, namely (1) to briefly review, compare and contrast these four CRA methods, (2) to provide a concise method for CRA introducing a quantitative component to the CAMBRA forms (CAMBRA 123), and (3) to guide the choice of CRA methods that will support caries management decisions. Comparison of Caries Risk Assessment Methods: In the present evaluation, the above-mentioned four CRA methods for ages 0-6 years and 6 years-adult were compared using 26 hypothetical patients (13 per age group). Comparison results show that Cariogram and CAMBRA categorized patients into identical risk categories. Each of the ADA and AAPD tools gave different results than CAMBRA and Cariogram in several comparison examples. CAMBRA 123 gave the same caries risk level results as the Cariogram and the CAMBRA methods for all hypothetical patients for both age groups. Conclusions: Both the Cariogram and the CAMBRA CRA methods are equally useful for identifying the future risk of dental caries. CAMBRA 123 shows promise as an easy-to-use quantitative method for CRA in clinical practice. The health care providers will be the ones to decide which CRA method will allow them to establish individualized, successful caries management therapies and how to combine these for the best care of their patients.

Evidence-Based Caries Management for All Ages-Practical Guidelines.

Introduction: The purpose of the present paper is to provide step-by-step guidelines for dental healthcare providers to manage dental caries based upon caries risk assessment (CRA) for ages 0-6 years and 6 years through adult. The manuscript reviews and updates the CAMBRA (caries management by risk assessment) system which includes CRA and caries management recommendations that are guided by the assessed risk level. Caries Risk Assessment: CAMBRA CRA tools (CRAs) have been evaluated in several clinical outcomes studies and clinical trials. Updated CAMBRA CRAs for ages 0-6 years and 6 years through adult are provided. These CRAs have been refined by the addition of a quantitative method that will aid the health care provider in determining the caries risk of individuals. Caries Management Based Upon Risk Assessment: Guidelines for individualized patient care are provided based upon the caries risk status, results of clinical exams and responses of the patient to questions in the CRA. These guidelines are based upon successful outcomes documented in several clinical outcomes studies and clinical trials. The paper includes a review of successful caries management procedures for children and adults as previously published, with additional emphasis on correct use of silver diamine fluoride (SDF) for children. The caries management plan for each individual is based upon reducing the caries risk factors and enhancing the protective factors with the additional aid of behavior modification. Beneficially altering the caries balance is coupled with minimal intervention restorative dentistry, if appropriate. These methods are appropriate for the management of dental caries in all patients.

Investigation into the optimum beam shape and fluence for selective ablation of dental calculus at lambda = 400 nm.

BACKGROUND AND OBJECTIVES: A frequency-doubled Ti:sapphire laser is shown to selectively ablate dental calculus. The optimal transverse shape of the laser beam, including its variability under water-cooling, is determined for selective ablation of dental calculus. STUDY DESIGN/MATERIALS AND METHODS: Intensity profiles under various water-cooling conditions were optically observed. The 400-nm laser was coupled into a multimode optical fiber using an f = 2.5-cm lens and light-shaping diffuser. Water-cooling was supplied coaxially around the fiber. Five human tooth samples (four with calculus and one pristine) were irradiated perpendicular to the tooth surface while the tooth was moved back and forth at 0.3 mm/second, varying between 20 and 180 iterations. The teeth were imaged before and after irradiation using light microscopy with a flashing blue light-emitting diode (LED). An environmental scanning electron microscope imaged each tooth after irradiation. RESULTS: High-order super-Gaussian intensity profiles are observed at the output of a fiber coiled around a 4-in. diameter drum. Super-Gaussian beams have a more-homogenous fluence distribution than Gaussian beams and have a higher energy efficiency for selective ablation. Coaxial water-cooling does not noticeably distort the intensity distribution within 1 mm from the optical fiber. In contrast, lasers focused to a Gaussian cross section (< or =50-microm diameter) without fiber propagation and cooled by a water spray are heavily distorted and may lead to variable ablation. Calculus is preferentially ablated at high fluences (> or =2 J/cm(2)); below this fluence, stalling occurs because of photo-bleaching of the calculus. Healthy dental hard tissue is not removed at fluences < or =3 J/cm(2). CONCLUSION: Supplying laser light to a tooth using an optical fiber with coaxial water-cooling is determined to be the most appropriate method when selectively removing calculus with a frequency-doubled Ti:sapphire laser. Fluences over 2 J/cm(2) are required to remove calculus efficiently since photo-bleaching stalls calculus removal below that value.