Assessment of a novel, easy-to-implement, aerosolized H2O2 decontamination method for single-use filtering facepiece respirators in case of shortage.

The COVID-19 pandemic has affected the world and caused a supply shortage of personal protection equipment, especially filtering facepiece respirators (FFP). This has increased the risk of many healthcare workers contracting SARS-CoV-2. Various strategies have been assessed to tackle these supply issues. In critical shortage scenarios, reusing single-use-designed respirators may be required. Thus, an easily applicable and reliable FFP2 (or alike) respirator decontamination method, allowing safe re-use of FFP2 respirators by healthcare personnel, has been developed and is presented in this study. A potent and gentle aerosolized hydrogen peroxide (12% wt) method was applied over 4 hr to decontaminate various brands of FFP2 respirators within a small common room, followed by adequate aeration and storage overnight. The microbial efficacy was tested on unused respirator pieces using spores of Geobacillus stearothermophilus. Further, decontamination effectiveness was tested on used respirators after one 12-hr shift by swabbing before and after the decontamination. The effects of up to ten decontamination cycles on the respirators' functionality were evaluated using material properties, the structural integrity of the respirators, and fit tests with subjects. The suggested H2O2 decontamination procedure was proven to be (a) sufficiently potent (no microbial recovery, total inactivation of biological indicators as well as spore inoculum on critical respirator surfaces), (b) gentle as no significant damage to the respirator structural integrity and acceptable fit factors were observed, and (c) safe as no H2O2 residue were detected after the defined aeration and storage. Thus, this easy-to-implement and scalable method could overcome another severe respirator shortage, providing enough flexibility to draft safe, effective, and logistically simple crisis plans. However, as highlighted in this study, due to the wealth of design and material used in different models and brands of respirators, the decontamination process should be validated for each FFP respirator model before its field implementation.

Community Masks - from an Emergency Solution to an Innovation Booster for the Textile Industry.

The COVID-19 pandemic resulted in shortages of personal protective equipment and medical devices in the initial phase. Agile small and medium-sized enterprises from regional textile industries reacted quickly. They delivered alternative products such as textile-based community masks in collaboration with industrial partners and research institutes from various sectors. The current mask materials and designs were further improved by integrating textiles with antiviral and antimicrobial properties and enhanced protection and comfort by novel textile/membrane combinations, key factors to increase the acceptance and compliance of mask wearing. The innocuity and sustainability of masks, as well as taking into account particular needs of vulnerable persons in our society, are new fields for textile-based innovations. These innovations developed for the next generation of facemasks have a high adaptability to other product segments, which make textiles an attractive material for hygienic applications and beyond.

Universities of Applied Sciences.

When the SARS-CoV-2 pandemic started,[1] science came to the immediate attention of the broad public. People and politicians were hanging on every word of medical doctors, virologists, molecular biologists, data scientists and many others in the hope of finding other protective measures than those used for centuries such as basic hygiene, distance, or quarantine. Here, at the Institute of Chemistry and Biotechnology at the Zurich University of Applied Sciences (ZHAW) we were also willing to provide scientific solutions to overcome the pandemic. Together with our partners from industry, we contributed to the development of a Swiss vaccine, are working on filters for active ventilated full protective suits and are developing tests to show the efficacy and safety of an active antiviral textile that allows controlled virus inactivation through an electrochemical reaction by applying a small current.

Evaluation of fiber and debris release from protective COVID-19 mask textiles and in vitro acute cytotoxicity effects.

Since the start of the current COVID-19 pandemic, for the first time a significant fraction of the world's population cover their respiratory system for an extended period with mostly medical facemasks and textile masks. This new situation raises questions about the extent of mask related debris (fibers and particles) being released and inhaled and possible adverse effects on human health. This study aimed to quantify the debris release from a textile-based facemask in comparison to a surgical mask and a reference cotton textile using both liquid and air extraction. Under liquid extractions, cotton-based textiles released up to 29'452 ± 1'996 fibers g-1 textile while synthetic textiles released up to 1'030 ± 115 fibers g-1 textile. However, when the masks were subjected to air-based extraction scenarios, only a fraction (0.1-1.1%) of this fiber amount was released. Several metals including copper (up to 40.8 ± 0.9 µg g-1) and iron (up to 7.0 ± 0.3 µg g-1) were detected in acid dissolved textiles. Additionally the acute in vitro toxicity of size-fractionated liquid extracts (below and above 0.4 µm) were assessed on human alveolar basal epithelial cells. The current study shows no acute cytotoxicity response for all the analyzed facemasks.

On the durability of surgical masks after simulated handling and wear.

After the spread of COVID-19, surgical masks became highly recommended to the public. They tend to be handled and used multiple times, which may impact their performance. To evaluate this risk, surgical masks of Type IIR were submitted to four simulated treatments: folding, ageing with artificial saliva or sweat and washing cycles. The air permeability, mechanical integrity, electrostatic potential, and filtration efficiency (FE) of the masks were measured to quantify possible degradation. Overall, air permeability and mechanical integrity were not affected, except after washing, which slightly degraded the filtering layers. Electrostatic potential and FE showed a strong correlation, highlighting the role of electrostatic charges on small particle filtration. A slight decrease in FE for 100 nm particles was found, from 74.4% for the reference masks to 70.6% for the mask treated in saliva for 8 h. A strong effect was observed for washed masks, resulting in FE of 46.9% (± 9.5%), comparable to that of a control group with no electrostatic charges. A dry store and reuse strategy could thus be envisaged for the public if safety in terms of viral and bacterial charge is ensured, whereas washing strongly impacts FE and is not recommended.

In situ infrared monitoring of the solid/liquid catalyst interface during the three-phase hydrogenation of nitrobenzene over nanosized Au on TiO2.

The three-phase hydrogenation of nitrobenzene catalysed by nanosized gold over titania was investigated in a slurry. Simultaneous in situ ATR-FTIR monitoring of the liquid phase and at the solid/liquid catalyst interface identified the species adsorbed on the catalyst and those in the liquid phase during the reaction. Nitrosobenzene was not detected analytically while the spectroscopic measurements strongly indicated phenylhydroxylamine as an intermediate reacting before desorbing from the catalyst surface. Under the same reaction conditions, azobenzene and hydrazobenzene were identified as intermediates during the hydrogenation of azoxybenzene to aniline. When nitrosobenzene or phenylhydroxylamine was alternately fed as reactant, azoxybenzene was produced via a disproportionation route. With the former, azoxybenzene was not further reduced by hydrogen because nitrosobenzene deactivated the catalyst. Combined with H(2) uptake, the spectroscopic measurements provided new insights into the reaction mechanism of the gold catalysed hydrogenation of nitrobenzene and an update of the corresponding kinetics.

Distribution of low quality filtering facepiece respirators during the COVID-19 pandemic: an independent analysis of the situation in Switzerland.

BACKGROUND: SARS-CoV-2 is a respiratory virus. Transmission occurs by droplets, contact and aerosols. In medical settings, filtering facepiece (FFP) respirators are recommended for use by personnel exposed to aerosol-generating procedures. During the COVID-19 pandemic, the demand for FFP respirators exceeded their supply worldwide and low-quality products appeared on the market, potentially putting healthcare workers at risk. AIMS: To raise awareness about variations in quality of imported FFP respirators in Switzerland during the COVID-19 pandemic, to draw attention to the current directives regulating the market launch of FFP respirators in Switzerland, to provide practical support in identifying suspicious products or documents and, finally, to offer strategies aimed at reducing the distribution of low-quality FFP respirators in the future. METHODS: Three Swiss laboratories, Spiez Laboratory and Unisanté in partnership with TOXpro SA individually set up testing procedures to evaluate aerosol penetration and fit testing of FFP respirators imported into Switzerland during COVID-19 pandemic. Additionally, Spiez Laboratory visually inspected the products, examined the certification documents and crosschecked the product information with international databases. RESULTS: Between 31 March and 15 June 2020, 151 FFP respirators were analysed. The initial assessment performed before testing allowed a reduction of up to 35% in the number of FFP respirators sent to Spiez Laboratory for evaluation, for which product information found to be faulty. After filtration efficiency evaluation and fit testing, 52% and 60% of all products tested by Spiez Laboratory and Unisanté-TOXpro SA, respectively, did not meet the minimum performance requirements established independently by the three Swiss laboratories. CONCLUSION: The demand for FFP respirators exceeded the supply capacity from established suppliers of the Swiss market. New production and import channels emerged, as did the number of poor-quality FFP respirators. FFP respirators remaining in stocks should be checked for conformity before being used, or eliminated and replaced if quality does not meet standards.

Proposal for a EN 149 acceptable reprocessing method for FFP2 respirators in times of severe shortage.

INTRODUCTION: Transmission of SARS-CoV-2 to health care workers (HCW) poses a major burden in the current COVID-19 pandemic. Unprotected exposure to a COVID-19 patient is a key risk factor for HCWs. Transmission mainly occurs by droplet transmission, or by aerosol generating procedures. Respirators such as filtering face piece masks (FFP2), also called respirators, are required to prevent transmission during aerosol generating procedures, as part of the personal protective equipment (PPE) for HCWs. However, many HCW were infected due to lack of PPE, or failure to use them. Therefore, the worldwide shortage of respirators triggered the development of reprocessing used FFP2 respirators or N95 respirators as standard in the US. Our proposal with H2O2 plasma sterilization for decontamination allows to reprocess FFP2, while they still meet the filtration efficiency required by EN 149. The protocol is simple, uses available resources in hospitals and can be rapidly implemented to decrease the shortage of respirators during this crisis. The goal of the study was the evaluate if respirators can be reprocessed and still fulfill the requirements for filtration efficiency outlined by EN 149. METHODS: Used FFP2 respirators - Model 3 M Aura™ 1862+ - were sterilized using a low temperature process hydrogen peroxide (H2O2), V-PRO® maX Low Temperature, a FDA (Food and Drug Administration) approved method to decontaminate FFP2 respirators. Decontaminated respirators were further checked for residual peroxide by a single-gas detector for H2O2. The total inward leakage of the protective respirators was quantitatively tested with 10 test persons in an atmosphere charged with paraffin aerosol according to the European Standard EN 149. The fit factor was calculated as the inverse of the total inward leakage. RESULTS: Ten new and ten decontaminated FFP2 respirators were tested for filtration efficiency. None of the respirators exceeded the maximum acceptable concentration of peroxide. More than 4000 respirators have been reprocessed so far, at cost of approximately 0.3 Euro/piece. CONCLUSIONS: FFP2 respirators can be safely reprocessed once after decontamination with plasma peroxide sterilization, whereafter they still fulfill EN 149 requirements. This allows to almost double the current number of available FFP2 respirators.