Effect of Linewidth on the Relative Intensity Noise in Random Distributed Feedback Raman Fiber Lasers.

We experimentally explore the relation between spectral linewidth and RIN transfer in half-open cavity random distributed feedback Raman lasers, demonstrating for the first time the possibility of adjusting the pump-to-signal RIN transfer intensity and cut-off frequency by using spectral filtering in the reflector section. We apply this approach to a 50-km laser system, operating in the C-Band, reliant on a standard single-mode fiber. We obtained a minimum bandwidth of 13 pm, which translates into a visible RIN cut-off at 800 MHz.

Anomalous relative intensity noise transfer in ultralong random fiber lasers.

We present, for the first time, an experimental demonstration of RIN noise transfer dampening at low frequencies in random distributed feedback ultralong Raman fibre lasers based on conventional telecommunication fibres. Furthermore, we present a thorough theoretical description of the phenomenon and demonstrate how our model can be used to predict the observed behaviour, identifying the general requirements for system improvement through RIN transfer reduction.

25 W single-frequency, low noise fiber MOPA at 1120 nm.

This Letter reports on the development of a 25 W single-frequency, all-fiber master oscillator power amplifier (MOPA) operating at 1120 nm. By heating the gain fiber at 75°C, an output power of 25.3 W is achieved with an optical-to-optical efficiency of 53.5%. The output shows no sign of stimulated Brillouin scattering and the signal to amplified spontaneous emission ratio is close to 40 dB. A M2 value of 1.15 and a polarization extinction ratio of 17 dB are measured. The relative intensity noise of the output is also characterized, reaching -155 dBc/Hz at 10 MHz at the maximum output power. The study of the noise dynamics highlights, for the first time to the best of our knowledge, an unpredicted behavior due to the strong backward amplified spontaneous emission.

Gain dynamics of clad-pumped Yb-fiber amplifier and intensity noise control.

Gain dynamics study provides an attractive method to understand the intensity noise behavior in fiber amplifiers. Here, the gain dynamics of a medium power (5 W) clad-pumped Yb-fiber amplifier is experimentally evaluated by measuring the frequency domain transfer functions for the input seed and pump lasers from 10 Hz to 1 MHz. We study gain dynamic behavior of the fiber amplifier in the presence of significant residual pump power (compared to the seed power), showing that the seed transfer function is strongly saturated at low Fourier frequencies while the pump power modulation transfer function is nearly unaffected. The characterization of relative intensity noise (RIN) of the fiber amplifier is well explained by the gain dynamics analysis. Finally, a 600 kHz bandwidth feedback loop using an acoustic-optical modulator (AOM) controlling the seed intensity is successfully demonstrated to suppress the broadband laser intensity noise. A maximum noise reduction of about 30 dB is achieved leading to a RIN of -152 dBc/Hz (~1 kHz-10 MHz) at 2.5 W output power.

Comparative study of ring and random cavities for fiber lasers.

An experimental comparison of three fiber laser structures with the same Raman gain medium is presented in order to establish the main pros and cons of each basic scheme. The first fiber laser is based on a hybrid ring-random fiber laser, the second one is a pure ring fiber laser, and the last one is a random fiber laser. Several aspects have been taken into account in the study. First, from the optical point of view, the parameters of interest compared are output power, lasing threshold, slope efficiency, power fluctuations, and the longitudinal modes have been analyzed. Second, the possible utilization of fiber lasers in digital modulated optical communication systems is also studied.

An in-reflection strain sensing head based on a Hi-Bi photonic crystal fiber.

A photonic crystal fiber-based sensing head is proposed for strain measurements. The sensor comprises a Hi-Bi PCF sensing head to measure interferometric signals in-reflection. An experimental background study of the sensing head is conducted through an optical backscatter reflectometer confirming the theoretical predictions, also included. A cost effective setup is proposed where a laser is used as illumination source, which allows accurate high precision strain measurements. Thus, a sensitivity of ~7.96 dB/me was achieved in a linear region of 1,200 µe.

Remote (250 km) fiber Bragg grating multiplexing system.

We propose and demonstrate two ultra-long range fiber Bragg grating (FBG) sensor interrogation systems. In the first approach four FBGs are located 200 km from the monitoring station and a signal to noise ratio of 20 dB is obtained. The second improved version is able to detect the four multiplexed FBGs placed 250 km away, offering a signal to noise ratio of 6-8 dB. Consequently, this last system represents the longest range FBG sensor system reported so far that includes fiber sensor multiplexing capability. Both simple systems are based on a wavelength swept laser to scan the reflection spectra of the FBGs, and they are composed by two identical-lengths optical paths: the first one intended to launch the amplified laser signal by means of Raman amplification and the other one is employed to guide the reflection signal to the reception system.