Effect of different surface treatment protocols on the bond strength between lithium disilicate and resin cements.

Because the use of hydrofluoric acid (HF) poses health risks if handled improperly, many clinicians prefer to have the ceramic restorations pre-etched in dental laboratories. However, during the try-in procedure, the pre-etched glass-ceramic restorations may be contaminated with saliva resulting in reduced bond strength. This in-vitro study aimed to investigate the effect of different surface treatments on the bond strength of lithium disilicate (LD) glass-ceramic restorations (IPS e.max Press, Ivoclar Vivadent) to two resin cements. One-hundred eighty blocks (4X4X3mm) of LD glass-ceramic were divided into twelve groups (n = 15), of which six received Variolink Esthetic DC (VE) cement and six received RelyX Ultimate (RU) cement, following the surface treatments: G1) Control: Hydrofluoric Acid + Silane (HF + Sil); G2) Hydrofluoric Acid + Saliva + Silane (HF + S + Sil); G3) Hydrofluoric Acid + Saliva + Ivoclean + Silane (HF + S + IC + Sil); G4) Hydrofluoric Acid + Saliva + Phosphoric Acid + Silane (HF + S + P + Sil); G5) Hydrofluoric Acid + Saliva + Monobond Etch & Prime (HF + S + EP); G6) Monobond Etch & Prime (EP). Following treatment, a resin-cement cylinder (2.3 mm diameter) was built on the glass-ceramic surface, photocured (20 s), stored in distilled water (37 °C, 24 h) and submitted to the shear bond strength test. Bond strength data (MPa) were subjected to two-way ANOVA and Tukey (α = 0.01). Cement type and surface treatment had a significant effect on the bond strength (p < 0.001) (Table 4). Single-step Monobond Etch & Prime (EP) significantly improved the bond strength of resin-cements to glass-ceramic with and without saliva contamination.

The influence of LED irradiance on the degree of conversion of resin luting agents under translucent zirconia.

This study aimed to evaluate the effect of different LED irradiance levels on the degree of conversion (DC) of dual-cured resin luting agents photocured through a high-translucency zirconia disc. Fifty-four disc specimens (approximately 0.1 × 6.0 × 6.0 mm) were prepared using 3 dual-cured resin luting agents (Panavia F 2.0, RelyX Unicem 2 Automix, and Calibra). Eighteen groups (n = 3) were evaluated. Test specimens were photocured through a 0.7 × 10.0-mm, high-translucency zirconia disc for 20 seconds using 1 of 3 different LED irradiances (mean output of 855, 1330, or 1750 mW/cm2 after 3 consecutive measurements with an LED radiometer). Specimens photocured directly, without a zirconia disc, were used as controls. Microattenuated total reflectance/Fourier-transform infrared spectroscopy was used to evaluate the extent of polymerization of all specimens prior to curing (baseline) and 24 hours after curing. Data were analyzed by 3-way analysis of variance and Tukey multiple comparisons test (α = 0.05). The RelyX Unicem 2 Automix and Panavia F 2.0 specimens showed no statistically significant difference in the mean DC after the use of different LED irradiance levels (P = 0.15 and P = 0.91, respectively) or when photocured with or without the use of a zirconia disc (P = 0.56 and P = 0.86, respectively). The Calibra specimens cured at the lowest irradiance level (855 mW/cm2) presented a significantly lower mean DC (P = 0.001). However, there was no statistically significant difference in the mean DC values when Calibra was photocured directly or through a zirconia disc (P = 0.33). The interpositioning of a high-translucency zirconia material did not reduce the DC of the tested resin luting agents compared to directly irradiated resin luting agents. The influence of different LED irradiance levels on the DC of dual-cured resin luting agents was material dependent.

Retrospective clinical evaluation of ceramic onlays placed by dental students.

STATEMENT OF PROBLEM: Indirect restorations with partial or complete occlusal surface coverage have been recommended to restore teeth with weakened walls in order to prevent cusp fracture. The success of these restorations when performed by dental students is unknown. PURPOSE: The purpose of this retrospective study was to evaluate the clinical performance of adhesively bonded ceramic onlay restorations placed by third- and fourth-year dental students. MATERIAL AND METHODS: Sixty-five ceramic onlays were placed in patients between 2009 and 2015. The onlays were laboratory or chairside fabricated with a computer-aided design and computer-aided manufacturing (CAD-CAM) system, using either IPS e.max Press or IPS e.max CAD. An adhesive technique and luting composite resin agent were used to cement the restorations. Thirty-seven onlays were evaluated clinically using the modified United States Public Health Service (USPHS) criteria. Data were statistically analyzed using the Cox proportional hazards model to compare tooth type and failures and the Fisher exact and McNemar tests to compare the USPHS criteria for significant differences (α=.05). Survival probability was calculated using the Kaplan-Meier algorithm. RESULTS: Five onlays were considered to be failures and needed replacement. According to the Kaplan-Meier analysis, the estimated survival rate was 96.3% after 2 years and 91.5% at 4 years. All 5 of the failures occurred on molars (13.5%) and none on premolars (P=.025). A statistically significant difference was found for marginal discoloration between onlays placed within 0 to 3 years and 3 to 6 years (P<.05) but no differences between any other criteria. CONCLUSIONS: Ceramic onlays placed by dental students demonstrated acceptable long-term clinical performance.

Marginal adaptation of CAD-CAM onlays: Influence of preparation design and impression technique.

STATEMENT OF PROBLEM: Factors that may affect the marginal adaptation of computer-aided design and computer-aided manufacturing (CAD-CAM) restorations include preparation design, impression technique, and CAD-CAM system. The influence of impression technique and preparation design on CAD-CAM partial coverage restorations has not been fully addressed. PURPOSE: The purpose of this in vitro study was to investigate the influence of direct and indirect digital scanning techniques and 2 preparation designs on the marginal adaptation of CAD-CAM onlays. MATERIAL AND METHODS: Two mesio-occlusal buccal onlay preparations with reduction of the mesiobuccal cusp were made: conventional preparation (CP) with a 1.2-mm modified shoulder margin and modified preparation (MP) flat cuspal reduction without shoulder. Virtual models were generated from each preparation by using a digital scanner (BlueCam; Dentsply Sirona) from the plastic teeth (direct digital scan) or from the stone dies (indirect digital scan). Onlays were designed using a CAD-CAM system (CEREC 4.0; Dentsply Sirona), and nanoceramic resin blocks (Lava Ultimate Restorative; 3M ESPE) were milled using the CEREC MCX milling machine. Marginal discrepancy was evaluated using an optical stereomicroscope at ×25 magnification in 18 locations distributed along the margins of the preparation. The data were analyzed by using 3-way ANOVA followed by the Tukey HSD test (α=.05). RESULTS: CP presented a statistically significant reduced average marginal adaptation (59 ±50 µm) than did MP (69 ±58 µm) (P<.001). The Tukey HSD test showed the presence of a significantly larger marginal discrepancy in the mesial and buccal locations of MP when compared with CP. Regarding impression techniques, the buccal location presented the smallest average marginal discrepancy in restorations fabricated with indirect impression when compared with direct impression (42 ±33 µm and 60 ±39 µm) (P<.001). CONCLUSIONS: The results showed that conventional preparation with a modified shoulder margin presented improved marginal adaptation compared with modified preparation with flat cuspal reduction. Direct and indirect digital scanning techniques produced restorations within a clinically acceptable range; however, the indirect scanning technique resulted in the fabrication of restorations with superior marginal adaptation on the buccal location.

Clinical evaluation of ceramic inlays and onlays fabricated with two systems: 12-year follow-up.

OBJECTIVES: The aim of this study was to evaluate the 12-year clinical performance of sintered (Duceram, Dentsply-Degussa, Dentsply International Inc., PA, USA)-D and pressable (IPS Empress, Ivoclar-Vivadent, Schaan, Leichtenstein)-IPS ceramic inlay and onlay restorations. METHODS: Eighty-six restorations were placed in 35 patients with a median age of 33 years by a single operator. The restorations were luted with dual-cured resin luting material (Variolink II, Ivoclar-Vivadent, Schaan, Leichtenstein) and Syntac Classic adhesive under rubber dam. The evaluations were conducted by two independent investigators at the baseline, 1, 2, 3, 5, and 12 years using the modified USPHS criteria. RESULTS: At the 12-year recall, 22 patients were evaluated (62.86 %), totalling 48 (55.81 %) restorations. Seven restorations were fractured (one from Duceram and six from IPS), eight restorations presented secondary caries (three from Duceram and five from IPS), nine restorations showed unacceptable defects at the restoration margin and needed repair or replacement (two from Duceram and seven from IPS), and four IPS restorations presented pulp sensitivity. CONCLUSION: Chi-square and Mann-Whitney tests revealed that IPS Empress system showed the best results for color match and surface texture (p < 0.05) but a significant worse result for fracture (p = 0.05). Wilcoxon test showed significant differences in relation to color match, surface texture, marginal discoloration, and marginal integrity between the baseline and 12-year recall for both ceramic systems. CLINICAL SIGNIFICANCE: This long-term clinical study observed that the main reasons for failure of ceramic restorations were related to fracture, recurrent caries, and decreased marginal integrity over time. Carefully monitoring of the ceramic-tooth interface may extend their clinical longevity.

Retention of tooth-colored restorations in non-carious cervical lesions--a systematic review.

OBJECTIVES: The aim of this review was to assess the effect of different adhesive systems and tooth preparation on the retention of tooth-colored restorative materials placed in non-carious cervical lesions (NCCLs). METHODS: Randomized clinical trials with a minimum of 3 years of follow-up that evaluated the effectiveness of tooth-colored materials, adhesive systems, and preparation techniques for the restoration of NCCLs were selected. The Cochrane Central Register of Controlled Trials (CENTRAL), EMBASE (OVID), the Latin American and Caribbean Health Sciences Literature database (LILACS), and Medline (OVID) electronic databases were searched from 1990 to 2013. RESULTS: Twenty-seven randomized clinical trials were included and reviewed. Meta-analysis was used to determine the relative risk of loss of tooth-colored NCCL restorations between different categories of adhesive systems. The effect of tooth preparation could not be similarly analyzed. CONCLUSION: The current best evidence indicates that a glass ionomer cement has a significantly lower risk of loss of a NCCL restoration compared to either a three-step etch-and-rinse or a two-step etch-and-rinse adhesive system; a three-step etch-and-rinse adhesive system has a significantly lower risk of loss of a NCCL restoration compared to a two-step etch-and-rinse adhesive system. No significant difference could be observed in the risk of loss of a tooth-colored NCCL restoration between a three-step etch-and-rinse adhesive system and either a two-step self-etch or a one-step self-etch adhesive system.

Survey of screw-retained versus cement-retained implant restorations used in both education and private dental practices.

AIMS: In the literature, it is still unclear if the decisions for selecting the type of implant crown-retaining system are based on scientific-based research or if the Universities' choices, Implant marketing trends, or finances could have a major influence on the private dentists' decisions. OBJECTIVES: Therefore, this study aimed to evaluate the crown-retaining system (cement- or screw-retained) used in dental schools and private dental practices. METHODS: A 13-item questionnaire was sent to Canadian dental schools (n = 10) and dental offices in London (n = 298), Canada. The questionnaire included demographic questions and questions to reveal the dentists' perspectives on prosthetic implant treatment between the two-retaining systems. Results were analyzed using descriptive statistics and multinomial logistic regression (p = 0.05). RESULTS: Twenty-four private dentists and five dental schools responded to the survey - 62.5% of private practitioners and 60% of universities reported using both systems. A trend was observed in using screw-retained systems by dentists who graduated 5-10 years ago. Straumann, Astra, and Nobel Biocare were the private practices and dental schools' preferred implant systems. The use of platform switching for all cases was selected by 54.2% of the private practitioners and 40% of the dental schools. Resin cement was the private practice's preferred cementation method; the dental schools used glass ionomer and zinc phosphate cement. The multinomial logistic regressions showed no statistical difference between the crown-retaining system chosen and the decision factors. The laboratory technician's recommendations and cost influenced the decision-making process for private dentists. For the universities, perio-restorative outcome, implant position, survival rates, institute preferences, and evidence-based research influenced the crown-retaining system's decision-making process.  CONCLUSION: The Canadian dental schools and private practice reported using both screw- and cement-retaining systems. However, there was a difference in the selection criteria as the universities showed a tendency towards a more research-based approach in their decision, while for the private practices, the technicians' recommendations and cost played a major role in the decision process. It was noted that the implant systems preconized by the Universities were observed to be used in private practices.

Overview of CEREC CAD/CAM chairside system.

This article describes CAD/CAM technology used in dentistry and different restorative materials used in conjunction with adhesive cementation with particular attention given to the evolution of the CEREC system, as well as various ceramics developed for this system. Advantages and limitations of materials and technique are also discussed.

Comparison of mechanical properties of five commercial dental core build-up materials.

OBJECTIVE: This study aimed to evaluate and compare the mechanical properties of five commercial core materials using fracture toughness (FT), Knoop hardness number (KHN), diametral tensile strength (DTS), and dynamic elastic moduli (DEM). METHODS: Composite material specimens were produced (Rock Core, CosmeCore, ParaCore, MultiCore Flow, and Filtek Supreme Plus). The FT test (n = 15) was performed using notchless triangular prism (NTP) specimens. FT was determined using an Instron testing machine. KHN (n = 3) was evaluated using three indentations applied on each specimen. DTS test (n = 15) was measured using an Instron testing machine. The density. of the specimens (n = 3) was determined by water displacement method. Dynamic Young's, shear moduli, and Poisson's ratio (n = 3) were measured by an ultrasonic method. Statistical analysis was conducted using ANOVA and a Tukey B rank order test (P = 0.05). RESULTS: Rock Core presented the lowest FT values. Filtek Supreme Plus and CosmeCore exhibited significantly higher KHN values than the rest of the materials. CosmeCore had the highest DTS value, which was statistically significant only compared to Rock Core. For DEM, Filtek Supreme Plus exhibited significantly higher Young's and shear moduli than the rest of the materials (P < 0.05). CONCLUSIONS: Results demonstrated significant differences in the FT, KHN, and DTS values of the core build-up materials tested. According to the elastic behavior of the core composite materials, Rock Core had the lowest Young's values.

Current Insights on Fiber Posts: A Narrative Review of Laboratory and Clinical Studies.

PURPOSE: The aim of this study was to review the literature related to the clinical performance and laboratory findings regarding fiber posts, as well as the cementation technique employed with their use. MATERIALS AND METHODS: A literature search was performed using an electronic database, PubMed/Medline, between 2010 and 2023. The terms used were "intra coronal post, fiber post, post cementation, and post length". Titles and abstracts were initially screened, and a full-text assessment was conducted for those that fulfilled the inclusion criteria. The reference list of the collected papers was also screened for further relevant citations. RESULTS: In this work, 135 potentially eligible studies were analyzed. Titles and abstracts of 90 studies followed the inclusion criteria and were selected for a full-text assessment, resulting in 50 studies selected. Moreover, additional studies from relevant citations were included, totaling 57 studies. CONCLUSION: According to the laboratory and clinical studies revised, the survival rate between fiber and prefabricated and cast metal posts was similar, and failures were mainly related to the loss of retention. The intra-canal post length of less than two-thirds of the root length presented successful results when ferrule was present. Furthermore, the ferrule increased the longevity of teeth restored with fiber posts. Additionally, the use of a surface treatment protocol for fiber posts and the adhesive cementation technique both contributed to the clinical success and longevity of the intra-canal post.

Retrospective Clinical Evaluation of RMGIC/GIC Class V Restorations.

The aim of this retrospective study was to evaluate the clinical performance of glass-ionomer cement (GIC) and resin-modified glass-ionomer cement (RMGIC) materials in Class V carious cervical lesions restored by dental students. Ninety-six (96) restorations performed with either GIC (Fuji IX) (n = 39) or RMGIC (Fuji II LC) (n = 57) were evaluated using the modified USPHS criteria by two independent investigators at two follow-up evaluations (two years apart). The Fisher statistical test was used to compare USPHS criteria and examine significant differences, with a significance level set at p < 0.05. The Kaplan-Meier algorithm was used to calculate the survival probability. The overall success rate of Class V restorations was 72.9% at the second follow-up evaluation, with restorations ranging in age from 2.5 to 3.5 years. The RMGIC (Fuji II LC) restorations exhibited a significantly higher overall success rate compared to the GIC (Fuji IX) restorations (p = 0.0104). Significant differences were observed in retention (p = 0.0034) and color match (p = 0.0023).

Five-Year Clinical Performance of Complex Class II Resin Composite and Amalgam Restorations-A Retrospective Study.

The aim of this retrospective study was to investigate the clinical performance of posterior complex resin composite (RC) and amalgam (AM) restorations after a five-year period. One hundred and nineteen complex Class II restorations placed by dental students were evaluated using the USPHS criteria. Data were analyzed using Chi-square, Mann-Whitney, and Wilcoxon tests at a 0.05 level of significance. After five years, the percentages of clinically satisfactory complex Class II RC and AM restorations were 78% and 76.8%, respectively. The main reasons for the failure of AM restorations included secondary caries (Bravo-10.1%), defective marginal adaptation (Charlie-8.7%), and fracture of the tooth (Bravo-7.2%). RC restorations presented failures related to the fracture of the restoration (Bravo-16%) and defective marginal adaptation (Charlie-8.2%). There was a significantly higher incidence of secondary caries for AM restorations (AM-10.1%; RC-0%; p = 0.0415) and a higher number of fractures for RC restorations (AM-4.3%; RC-16%; p = 0.05). Regarding anatomy, AM restorations presented a significantly higher number of Alfa scores (49.3%) compared to RC restorations (22.4%) (p = 0.0005). The results of the current study indicate that complex class II RC and AM restorations show a similar five year clinical performance.

Post-fatigue fracture load, stress concentration and mechanical properties of feldspathic, leucite- and lithium disilicate-reinforced glass ceramics.

Objective: To evaluate the mechanical properties of different CAD/CAM ceramic systems and the post-fatigue fracture and stress distribution when used as cemented crowns. Materials and methods: Sixty (60) CAD/CAM monolithic crowns were milled using three different ceramic materials (FD - Feldspathic [Vita Mark II]), LE - Leucite-based ceramic [IPS Empress CAD] and LD - Lithium Disilicate [IPS e.max CAD]) and adhesively cemented on resin composite dyes. Specimens were stored in distillated water (37 °C) for 7 days. After, half of the crowns were submitted to immediate fracture load test while the other half was submitted to fatigue cycling. The average cement layer of approximately 80 µm was assessed using scanning electron microscopy (SEM). The average thickness was used in the three-dimensional (3D) Finite Element Analysis (FEA). For each ceramic material, the density, Poisson ratio, shear modulus, Young modulus, fracture toughness, and true hardness were assessed (n = 3). The data was used to assess the Maximum Principal Stress throughout 3D-FEA according to each material during load to fail and post-fatigue. Data were submitted to two-way ANOVA and Tukey test (α = 0.05). Results: LD showed the highest compression load, density, shear modulus, Young modulus, fracture toughness and true hardness values. While LE presented the lowest mechanical properties values. There is no difference in the Poisson ratio between the evaluated ceramics. Conclusion: LD was susceptible to aging process but presented stronger physicomechanical properties, showing the highest post-fatigue fracture load and highest stress magnitude.

In vitro shear bond strength of resin-based luting cements to dentin.

The aim of this study was to determine how resin cement, self-adhesive resin cement, and resin-modified glass ionomer cement affected shear bond strength to dentin. Sixty composite resin disks (3 mm in diameter x 3 mm in length) were prepared and divided into four groups (n = 15): Group 1, composite disk bonded to dentin with composite resin and a bonding agent; Group 2, composite disk bonded to dentin with a self-adhesive resin cement; Group 3, composite disk bonded to dentin with a different self-adhesive resin cement; and Group 4, composite disk bonded to dentin with a resin-modified glass ionomer cement. The composite resin was loaded into a syringe (internal diameter 3 mm), photocured in an oven, and cut into 3 mm slices with a low-speed saw. The samples were bonded to dentin per the manufacturer's instructions. All specimens were stored in distilled water (at 37 degrees C) for 24 hours. The shear bond strength test was conducted using a universal testing machine at a crosshead speed of 0.5 mm/min until failure. Conventional resin cement and a bonding agent exhibited significantly higher shear bond strength values than all other materials tested.

Evaluation of the Mechanical Properties of Three Resin-Modified Glass-Ionomer Materials.

This study is aimed at evaluating the flexural strength (FS), fracture toughness (FT), and diametral tensile strength (DTS) of three resin-modified glass-ionomer cements (RMGICs): Ketac Nano, Riva Light Cure, and Fuji II LC. One hundred twenty specimens were prepared from the RMGIC materials (n = 10). The cements were mixed and inserted into different mould sizes according to the test performed: FS: rectangular Teflon mould (32 mm × 3.15 mm × 2 mm); FT: notchless triangular prism (NTP) Teflon mould (6 mm × 6 mm × 6 mm × 12 mm); and DTS: ring road stainless steel mould (6 mm × 3 mm). Specimens were light cured for 20 seconds on each surface and stored in distilled water at 37°C ± 2°C for seven days prior to tests. To evaluate the influence of storage in the mechanical properties of the RMGIs, specimens tested for DTS were stored in distilled water at 37°C ± 2°C for 32 days prior to test. Data were analyzed by ANOVA and Tukey's test (α = 0.05). Fuji II LC presented significantly higher values for all tests employed when compared to Ketac Nano and Riva LC RMGIs. There was no significant difference on DTS before and after the 32-day storage for each material. Fuji II LC presented superior mechanical properties when compared to Ketac Nano, and Riva LC storage showed no influence on the mechanical properties of the RMGI materials tested.

Shear bond strength of resin cement bonded to alumina ceramic after treatment by aluminum oxide sandblasting or silica coating.

PURPOSE: To evaluate the shear bond strength and bond durability between a dual-cured resin cement (RC) and a high alumina ceramic (In-Ceram Alumina), subjected to two surface treatments. MATERIALS AND METHODS: Forty disc-shaped specimens (sp) (4-mm diameter, 5-mm thick) were fabricated from In-Ceram Alumina and divided into two groups (n = 20) in accordance with surface treatment: (1) sandblasting by aluminum oxide particles (50 µm Al(2) O(3) ) (SB) and (2) silica coating (30 µm SiO(x) ) using the CoJet system (SC). After the 40 sp were bonded to the dual-cured RC, they were stored in distilled water at 37°C for 24 hours. After this period, the sp from each group were divided into two conditions of storage (n = 10): (a) 24 h-shear bond test 24 hours after cementation; (b) Aging-thermocycling (TC) (12,000 times, 5 to 55°C) and water storage (150 days). The shear test was performed in a universal test machine (1 mm/min). RESULTS: ANOVA and Tukey (5%) tests noted no statistically significant difference in the bond strength values between the two surface treatments (p = 0.7897). The bond strengths (MPa) for both surface treatments reduced significantly after aging (SB-24: 8.2 ± 4.6; SB-Aging: 3.7 ± 2.5; SC-24: 8.6 ± 2.2; SC-Aging: 3.5 ± 3.1). CONCLUSION: Surface conditioning using airborne particle abrasion with either 50 µm alumina or 30 µm silica particles exhibited similar bond strength values and decreased after long-term TC and water storage for both methods.

Diametral tensile strength of composite core material with cured and uncured fiber posts.

The aim of this study was to determine the influence of different types of posts and post head designs on the fracture resistance of a composite resin core material using the diametral tensile strength (DTS ). Seventy-five disc specimens were prepared using a composite core and prefabricated glass fiber posts and were divided into four test groups and one control group (n=15). The use of fiber posts reduced the DTS of the composite core material; the DTS value of the control material was significantly higher (p=0.05) than all of the test groups.

Adhesive cementation of etchable ceramic esthetic restorations.

This article describes the different materials and techniques that are used for adhesive cementation. Particular attention is given to treatments suitable for dentin, as well as the selection of surface treatments for various restorative materials. Factors related to the durability and stability of the adhesive process, as well as the clinical and laboratory procedures required for cementation, are also discussed.

The effect of dentin adhesive and cure mode on film thickness and microtensile bond strength to dentin in indirect restorations.

This study evaluated the influence of dentin adhesive application technique (pre-curing vs non precuring) on microtensile bond strength (microTBS) to dentin and adhesive layer thickness in indirect resin restorations. Seven proprietary dentin adhesives were tested, including one-step and multistep products. Experimental groups included adhesive pre-cure (PC) with a halogen light source and no pre-cure (NPC) prior to resin cement insertion. Thirty caries-free molars received an MO inlay preparation. Inlays made with Tetric Ceram resin composite were cemented using a dual-cured resin luting agent. Prior to inlay cementation, each tooth was treated with one dentin bonding agent, using pre-cure (PC) or no pre-cure (NPC). After storage in distilled water at 37 degrees C for 24 hours, the teeth were sectioned along their long axis to produce serial sticks for microtensile bond strength testing at 0.5 mm/minute. The results were subjected to statistical analysis by one-way and two-way analysis of variance (ANOVA) and Tukey's multiple comparison test (p < or = 0.05). For the film thickness evaluation, 10 additional teeth were restored and sectioned mesiodistally. The thickness of the adhesive layer was evaluated by SEM at 1000x magnification at the pre-selected locations. The microTBS varied from 11.7 +/- 4.5 MPa to 43.4 +/- 9.8 MPa. The effect of pre-curing the adhesive was material specific. No adhesive layer was visualized for the adhesives used without the pre-curing step. The thickness of the adhesive layer for the pre-cured groups varied according to the different areas analyzed.