W-type normal dispersion thulium-doped fiber-based high-energy all-fiber femtosecond laser at 1.7 µm.

We propose a parabolic W-type thulium-doped fiber for the 1.7 µm high-energy femtosecond pulsed laser. Despite its attractive normal dispersion, the fiber offers high gain in 1.7 µm region thanks to its distributed short-pass filtering effect. With a proper dispersion management in an all-fiber chirped pulse amplification (CPA) scheme, we demonstrate so far the highest pulse energy of 128.0 nJ in a stable pulse of 174 fs in the 1.7-1.8 µm region, which marks above an order of magnitude improvement in pulse energy while exhibiting the shortest pulse duration among fiber-based CPA works at 1.7 µm. Hence, we provide a pathway to an energy scalable and efficient femtosecond laser at 1.7 µm via a compact and elegant all-fiber solution.

Power stable 1.5-10.5 µm cascaded mid-infrared supercontinuum laser without thulium amplifier.

We demonstrate a simple and power stable 1.5-10.5 µm cascaded mid-infrared 3 MHz supercontinuum fiber laser. To increase simplicity and decrease cost, the design of the fiber cascade is optimized so that no thulium amplifier is needed. Despite the simple design with no thulium amplifier, we demonstrate a high average output power of 86.6 mW. Stability measurements for seven days with 8-9 h operation daily revealed fluctuations in the average power with a standard deviation of only 0.43% and a power spectral density stability of ±0.18dBm/nm for wavelengths <10µm. The high-repetition-rate, robust, and cheap all-fiber design makes this source ideal for applications in spectroscopy and imaging.

All-fiber short-wavelength tunable mode-locked fiber laser using normal dispersion thulium-doped fiber.

We report an all-fiber high pulse energy ultrafast laser and amplifier operating at the short wavelength side of the thulium (Tm) emission band. An in-house W-type normal dispersion Tm-doped fiber (NDTDF) exhibits a bending-induced distributed short-pass filtering effect that efficiently suppresses the otherwise dominant long wavelength emission. By changing the bending diameter of the fiber, we demonstrated a tunable mode-locked Tm-doped fiber laser with a very wide tunable range of 152 nm spanning from 1740 nm to 1892 nm. Pulses at a central wavelength of 1755 nm were able to be amplified in an all-fiber configuration using the W-type NDTDF, without the use of any artificial short-pass filter or pulse stretcher. The all-fiber amplifier delivers 2.76 ps pulses with an energy of ∼32.7 nJ without pulse break-up, due to the normal dispersion nature of the gain fiber, which marks so far, the highest energy amongst fiber lasers in the 1700 nm-1800 nm region.

Femtosecond Bragg grating inscription in an Yb-doped large-mode-area multicore fiber for high-power laser applications.

We demonstrate a direct inscription of a fiber Bragg grating (FBG) in the active cores of an Yb-doped large mode area multicore fiber (MCF). An ultrashort pulsed laser is used to inscribe the FBG simultaneously in all six cores. In order to validate the FBG reflection and uniformity, the FBG is incorporated as a rear mirror in a fiber laser oscillator setup. The MCF, which has been fabricated in-house, has six cores located in a hexagonal-ring shape, each with a 19 µm diameter and an NA of ∼0.067. A reflection of ∼96% was measured at a center Bragg wavelength of ∼1062nm for the inscribed FBG. The laser performance of the MCF with the femtosecond inscribed FBG at its end shows a similar performance to lasing with a free-space commercial volume Bragg grating as the rear-reflector. A slope efficiency of ∼72.4% and a maximum (pump limited) output power of 51.8 W have been obtained for the FBG setup. An effective M2 of 3.88, indicating a somewhat multimode operation and a narrow bandwidth of ∼0.19nm, has been measured for this fiber laser.

Influence of pulse duration and repetition rate on mid-infrared cascaded supercontinuum.

We experimentally investigate the influence of varying pulse parameters on the spectral broadening, power spectral density, and relative intensity noise of mid-infrared (mid-IR) in-amplifier cascaded supercontinuum generation (SCG) by varying the pulse duration (35 ps, 1 ns, 3 ns) and repetition rate (100, 500, 1000 kHz). The system is characterized at the output of the erbium-ytterbium-doped in-amplifier SCG stage, the thulium/germanium power redistribution stage, and the passive ZBLAN fiber stage. In doing so, we demonstrate that the output of the later stages depends critically on the in-amplifier stage, and relate this to the onset of modulation instability.

Ultra-low NA step-index large mode area Yb-doped fiber with a germanium doped cladding for high power pulse amplification.

High concentration rare earth doped, large mode area (LMA) step-index fibers, which feature a very high cladding absorption per unit length at the pump wavelength, high efficiency, and excellent beam quality, are ideal for high power pulsed fiber lasers/amplifiers where large effective mode areas and short device lengths are crucial in order to reduce detrimental nonlinear effects associated with high peak power operation. In this Letter, we realize low numerical aperture (NA) high absorption fibers, simply by employing a germanium (Ge)-doped cladding rather than a pure silica cladding to offset the high refractive index associated with using a high concentration of ytterbium (Yb) in the core. This approach allows us to separate the two inter-linked fiber design parameters of pump absorption and NA in a step-index fiber. Using a conventional modified chemical vapor deposition process combined with solution doping, a low NA (0.04), LMA (475µm2) silica fiber is fabricated with a cladding absorption value of >20dB/m, which is the highest value among LMA step-index fibers with NA<0.06 so far reported to the best of our knowledge. The fabricated Yb-doped fiber was tested in a high-power picosecond amplifier system and enabled the generation of 190 ps laser pulses with a 101 µJ pulse energy and 0.5 MW peak power at an average power of 150 W.

Reconfigurable multiwavelength fiber laser based on multimode interference in highly germanium-doped fiber.

A reconfigurable multiwavelength erbium-doped fiber laser based on an all-fiber multimode interferometer (MMI) is proposed and experimentally demonstrated. The interferometer is constructed by sandwiching a section of highly germanium-doped fiber (HGDF) between two sections of single-mode fiber. The insertion loss of the interferometer is as low as 2 dB. Due to the polarization-dependent spectral filtering effect formed by the MMI, by rotating the intracavity polarization controller, the laser output can be switched among single-, dual-, and triple-wavelength lasing states with optical signal-to-noise ratio up to 50 dB. In particular, the obtained dual-wavelength state shows high stability with wavelength shift within $ \pm {0.04}\;{\rm nm}$±0.04nm, wavelength spacing variation within $ \pm {0.03}\;{\rm nm}$±0.03nm, and power fluctuation within $ \pm {0.04}\;{\rm dB}$±0.04dB by monitoring the output spectra over 8 h at room temperature. By changing the length of the HGDF, the wavelength spacing can also be flexibly manipulated. Taking the advantages of reconfiguration, low cost, and easy fabrication, this fiber laser may have great potential in various optical applications.

Ultra-short wavelength operation of thulium-doped fiber amplifiers and lasers.

We fabricate and characterize a germanium/thulium (Ge/Tm) co-doped silica fiber in order to enhance the gain at the short wavelength edge of the thulium emission band (i.e. 1620-1660 nm). The Ge/Tm doped fiber shows an intrinsic blue-shifted absorption/emission cross-section compared to aluminum/thulium (Al/Tm) co-doped fiber, which greatly improves the short wavelength amplification and has enabled us to further extend the shortest wavelength of emission towards 1600 nm. Using this glass fiber composition, we have demonstrated both a silica-based thulium doped fiber amplifier (TDFA) in the 1628-1655 nm waveband and a tunable thulium-doped fiber laser (TDFL) capable of accessing the telecom U-band wavelength region. These results represent by far the shortest amplifier/laser wavelengths reported to-date from TDFAs/TDFLs.

Multimode-pumped Raman amplification of a higher order mode in a large mode area fiber.

We report the first demonstration of Raman amplification in a fiber of a single Bessel-like higher order mode using a multimode pump source. We amplify the LP08-mode with a 559-µm2 effective mode area at a signal wavelength of 1115 nm in a pure-silica-core step-index fiber. A maximum of 18 dB average power gain is achieved in a 9-m long gain fiber, with output pulse energy of 115 µJ. The Raman pump source comprises a pulsed 1060 nm ytterbium-doped fiber amplifier with V-value ~30, which is matched to the Raman gain fiber. The pump depletion as averaged over the signal pulses reaches 36.7%. The conversion of power from the multimode pump into the signal mode demonstrates the potential for efficient brightness enhancement with low amplification-induced signal mode purity degradation.

Step-index high-absorption Yb-doped large-mode-area fiber with Ge-doped raised cladding.

We report an all-solid large-mode-area (LMA) step-index fiber offering high absorption and low core numerical aperture (NA) by introducing a highly ytterbium-doped P:Al core and germanium-doped cladding. The fiber provides core absorption of ∼1200 dB/m at 976 nm with a low 0.07 core NA, due to the raised Ge cladding. Furthermore, matched profiles of P and Al across the core are successfully obtained with high concentration of Yb2O3 around 0.4 mol%. The fiber characteristics are routinely achievable by conventional modified chemical vapor deposition with a solution doping technique. A highly efficient laser with >100 W output power, 86% slope efficiency with respect to launched pump power, and a mean M2 of 1.34 has been demonstrated using the fabricated LMA step-index fiber. We also report 80% laser slope efficiency with 58 W output power (pump power limited) within only 0.5 m of the fiber when pumped by a wavelength-stabilized laser diode.

Bendable large-mode-area fiber with a non-circular core: publisher's note.

This publisher's note amends the spelling of the second author's name in Appl. Opt.57, 6388 (2018)APOPAI0003-693510.1364/AO.57.006388.

Bendable large-mode-area fiber with a non-circular core.

We investigate mode-area-scaling and bending performances of a Yb-doped large-mode-area fiber with an elongated non-circular core. Such fiber can be bent in the plane of its short axis to suppress bending effects, such as mode area reduction and mode profile distortion. Meanwhile, the other orthogonal axis can be stretched for mode area scaling. Calculations show that for fibers with the same mode area, the higher the aspect ratio between the long axis and short axis, the less sensitive the fiber will be to bending effects. However, mode area scaling is limited by the increased beat length (BL) between the fundamental mode (FM) and the second-order mode, leading to mode degeneracy at higher aspect ratios. Within the 100 mm BL, the FM area is scalable to 3000 µm2 in a bent fiber. To facilitate FM operation, we study mode-selective gain through confined doping. Thanks to the small bending distortions, the confined-doping approach works well in the bent large-mode-area fiber. In addition, the advantage of tandem pumping is also discussed in terms of preferential modal gain. A non-circular core fiber with a 41 µm short axis and 120 µm long axis was fabricated in-house. We evaluated the fiber in a linear laser cavity pumped by a 975 nm laser diode. The maximum output power obtained was 191 W, with slope efficiency of approximately 67% with respect to launched pump power. The output signal has good beam qualities with M2 of ∼1.5 and ∼3.1, respectively, along the short and long axis.