Effect of time and photoactivated face on bond strength of brackets and on degree of monomer conversion.

OBJECTIVE: To evaluate the effect of four different photoactivation protocols (according to "photoactivated faces" - mesial/distal, cervical/incisal or center - and "photoactivation time" - 6-3 s) of a high-power photo activator (Valo Cordless®-Ultradent) on the shear bond strength (SBS) between metal brackets and dental enamel and on the degree of conversion (DC) of an orthodontic resin. MATERIALS AND METHODS: 40 bovine incisor crowns were randomly assigned to 4 groups (n = 10). The brackets were bonded with Transbond XT® resin using 4 protocols according to the "photoactivation protocol" factor (which was subdivided into photoactivated faces and photoactivation time): V3C = 3 s + center; V6C = 6 s + center; V3M3D = 3 s on mesial + 3 s on distal; V3C3I = 3 s on cervical + 3 s on incisal. All the samples were stored for 4 months (water,37ºC) and then subjected to a SBS test (100KgF,1 mm/min). 40 resin discs were made to evaluate the monomer degree of conversion. Data from the SBS and DC were assessed by One-way ANOVA and Tukey's test (5%). Bond failures were analyzed according to the Adhesive Remnant Index (ARI) and evaluated by the Kruskal-Wallis test (5%). RESULTS: There was a statistically significant difference (p = 0.008) in the One-way ANOVA result for SBS values between all groups, but the protocols showed statistically similar results (p ≥ 0.05-Tukey's tests) concerning the photoactivated faces (V6C, V3M3D and V3C3I) and photoactivation time (V3C and V6C) factors individually. There was no statistically significant difference (p ≥ 0.05) in the One-way ANOVA result for DC values. CONCLUSION: The SBS and DC values will vary depending on the protocol applied. CLINICAL RELEVANCE: It is possible to maintain the bracket fixation quality with the use of a high-power LED photo activator associated with a shorter photoactivation time. However, it is assumed that not all types of protocols that might be applied will provide quality bonding, such as V3C, V3M3D and V3C3I, which may - depending on the SBS and DC values - affect the final treatment time, due to brackets debonding, or increase of possibility of damage to dental enamel during bracket removal. Clinical studies are suggested to confirm the hypotheses of this research.

Influence of build direction, post-polymerization time, and aging on the fracture resistance and marginal and internal discrepancies of three-dimensional printed provisional crowns.

To evaluate the effect of build direction, post-polymerization time, and aging on the fracture resistance, failure mode, margin quality and Marginal (MD) and Internal Discrepancies (ID), and degree of conversion of tridimensional (3D) printed provisional crowns using the liquid crystal display technique (LCD). A left mandibular first molar was prepared and scanned. After, a full crown was designed (ExoCad) and exported to the LCD-printer software. One hundred and eighty crowns were printed at two build directions (30°, 90°) and post-polymerized for different periods (15, 30, 45 min). Half of the samples were aged (ST) in distilled water (37 °C/90 days). The marginal quality of the crowns was evaluated by the Schriwer method under a stereomicroscope (40x). The replica technique was used to measure the MD and ID and measured under a stereomicroscope (10x), through 20 reference points defined in 5 regions: Occlusal (O), Cusp (CP), Axial (AX), Chamfer (CH), and Finish Line (F). After, the crowns were cemented onto the respective dies using temporary cement and submitted to compression test (ISO150, 1 mm/min, 100 kgf).The failure mode was classified by Burke's fracture mode. The degree of conversion was evaluated through Fourier Transform Infrared Spectroscopy. The data (µm) of MD and ID and fracture resistance (N) were subjected to ANOVA (3 factors) and Tukey's test (5%); Weibull analysis was also performed for fracture resistance data (N). For MD, ID and fracture resistance ANOVA revealed that all factors (P < .001) were significant. For aged groups, the crowns printed at 30° showed lower MD (Tukey). The O_90_30 min (172.13A µm) and O_90_15 min (170.20A µm) groups showed the highest ID values. Higher resistance values were observed for the 30_45 min (844.30A N), 30_30 min (835.35A N), and 90_30 min (820.62A N) groups (Tukey). In the margin analysis, 98.6% of the crowns printed at 30° showed smooth margins without defects. The most prevalent fracture mode (41.7%) was Burke type 5. The degree of conversion (DC) increased with increasing post-polymerization time and aging. Printing provisional crowns at 30° provided lower crown MD and ID, as well as higher fracture resistance. A post-polymerization time of 30 min resulted in higher crown fracture resistance, while aging reduced the resistance of the crowns.

Effect of different surface treatments and adhesive cementation on the surface topography and flexural strength of translucent and ultra-translucent monolithic zirconia.

PURPOSE: To evaluate the effect of different surface treatments and adhesive cementation on the miniflexural strength (MFS) of monolithic zirconia. MATERIALS AND METHODS: Two-hundred and forty (240) sintered bars of translucent zirconia (ZT) and ultra-translucent zirconia (ZUT) were obtained (8 mm ×2 mm ×1 mm). The bars were divided into 16 groups (n = 15) according to the factors "Zirconia" (ZT and ZUT), "Cementation" (Cem) and "surface treatment" (Ctrl:Control, Al:Aluminum oxide/Al2O3 50 µm, Si:Silica/SiO2 coated alumina particles oxide 30 µm, Gl:Glazing+hydrofluoric acid). Half of the bars received an adhesive layer application, followed by application of resin cement and light curing. The surface roughness was measured in non-cemented groups. All the bars were subjected to the MFS test (1.0 mm/min; 100 kgf). Scanning electron microscopy was used for qualitative analyses. MFS data (MPa) and roughness (µm) were statistically evaluated by three-way and two-way ANOVA respectively and Tukey's test (5%). RESULTS: The surface treatment and the interaction were significant for roughness. Glazing promoted less roughness compared to silicatization. Regarding MFS, only the zirconia and surface treatment factors were significant. For ZT, the sandblasted groups had an increase in MFS and glazing reduced it. There was no difference between the groups without cementation for the ZUT; however, ZUT.Si/Cem, and ZUT.Al/Cem obtained superior MFS among the cemented groups. CONCLUSIONS: Sandblasting increases the flexural strength for ZT, while glaze application tends to reduce it. Applying resin cement increases the flexural strength of ZUT when associated with sandblasting. Sandblasting protocols promote greater surface roughness.

Multiple variation of right renal and gonadal vascularization: report of two cases.

We present two cases of multiple anatomical variations of the renal and gonadal vessels. The first case presented duplication of the renal vein and the presence of an accessory renal artery. However, the most interesting fact, in this case, was that the right gonadal vein emptied into the inferior right renal vein instead of ending in the inferior vena cava as would typically be the case. In the second case, we also found an accessory renal artery and the right gonadal vein emptied at the exact junction between the right renal vein and the inferior vena cava. Clinicians and surgeons should be familiar with anatomical variations to provide an accurate diagnosis during preoperative studies and to avoid surprises in abdominal surgical procedures.

Este estudo apresenta dois casos de variação anatômica múltipla de vasos renais e gonadais. O primeiro caso apresentou uma duplicação da veia renal e a presença de uma artéria renal acessória. Porém, o fato mais interessante nesse caso foi a veia gonadal direita desembocar na veia renal direita inferior em vez de terminar na veia cava inferior, como seria o normal. No segundo caso, além de também encontrarmos uma artéria renal acessória, a veia gonadal direita desembocava no exato ponto de junção entre a veia renal direita e a veia cava inferior. Clínicos e cirurgiões devem estar familiarizados com a presença de possíveis variações dos vasos renais e gonadais, sendo um conhecimento imprescindível para obter um diagnóstico mais preciso e para evitar surpresas em procedimentos cirúrgicos abdominais.

Frequency of pleural effusion in dengue patients by severity, age and imaging modality: a systematic review and meta-analysis.

BACKGROUND: Identification of pleural effusion (PE) in dengue infection is an objective measure of plasma leakage and may predict disease progression. However, no studies have systematically assessed the frequency of PE in patients with dengue, and whether this differs across age and imaging modality. METHODS: We searched Pubmed, Embase Web of Science and Lilacs (period 1900-2021) for studies reporting on PE in dengue patients (hospitalized and outpatient). We defined PE as fluid in the thoracic cavity detected by any imaging test. The study was registered in PROSPERO (CRD42021228862). Complicated dengue was defined as hemorrhagic fever, dengue shock syndrome or severe dengue. RESULTS: The search identified 2,157 studies of which 85 studies were eligible for inclusion. The studies (n = 31 children, n = 10 adults, n = 44 mixed age) involved 12,800 patients (30% complicated dengue). The overall frequency of PE was 33% [95%CI: 29 to 37%] and the rate of PE increased significantly with disease severity (P = 0.001) such that in complicated vs. uncomplicated dengue the frequencies were 48% and 17% (P < 0.001). When assessing all studies, PE occurred significantly more often in children compared to adults (43% vs. 13%, P = 0.002) and lung ultrasound more frequently detected PE than conventional chest X-ray (P = 0.023). CONCLUSIONS: We found that 1/3 of dengue patients presented with PE and the frequency increased with severity and younger age. Importantly, lung ultrasound demonstrated the highest rate of detection. Our findings suggest that PE is a relatively common finding in dengue and that bedside imaging tools, such as lung ultrasound, potentially may enhance detection.

Chemical Signatures of Seasonally Unique Anthropogenic Influences on Organic Aerosol Composition in the Central Amazon.

Urbanization and fires perturb the quantities and composition of fine organic aerosol in the central Amazon, with ramifications for radiative forcing and public health. These disturbances include not only direct emissions of particulates and secondary organic aerosol (SOA) precursors but also changes in the pathways through which biogenic precursors form SOA. The composition of ambient organic aerosol is complex and incompletely characterized, encompassing millions of potential structures relatively few of which have been synthesized and characterized. Through analysis of submicron aerosol samples from the Green Ocean Amazon (GoAmazon2014/5) field campaign by two-dimensional gas chromatography coupled with machine learning, ∼1300 unique compounds were traced and characterized over two seasons. Fires and urban emissions produced chemically and interseasonally distinct impacts on product signatures, with only ∼50% of compounds observed in both seasons. Seasonally unique populations point to the importance of aqueous processing in Amazonian aerosol aging, but further mechanistic insights are impeded by limited product identity knowledge. Less than 10% of compounds were identifiable at an isomer-specific level. Overall, the findings (i) provide compositional characterization of anthropogenic influence on submicron organic aerosol in the Amazon, (ii) identify key season-to-season differences in chemical signatures, and (iii) highlight high-priority knowledge gaps in current speciated knowledge.

Flexural strength, surface roughness, micro-CT analysis, and microbiological adhesion of a 3D-printed temporary crown material.

OBJECTIVE: To evaluate the thermocycling effect of 3D-printed resins on flexural strength, surface roughness, microbiological adhesion, and porosity. MATERIALS AND METHODS: 150 bars (8 × 2 × 2 mm) and 100 blocks (8 × 8 × 2 mm) were made and divided into 5 groups, according to two factors: "material" (AR: acrylic resin, CR: composite resin, BIS: bis-acryl resin, CAD: CAD/CAM resin, and PRINT: 3D-printed resin) and "aging" (non-aged and aged - TC). Half of them were subjected to thermocycling (10,000 cycles). The bars were subjected to mini-flexural strength (σ) test (1 mm/min). All the blocks were subjected to roughness analysis (Ra/Rq/Rz). The non-aged blocks were subjected to porosity analysis (micro-CT; n = 5) and fungal adherence (n = 10). Data were statistically analyzed (one-way ANOVA, two-way ANOVA; Tukey's test, α = 0.05). RESULTS: For σ, "material" and "aging" factors were statistically significant (p < 0.0001). The BIS (118.23 ± 16.26A) presented a higher σ and the PRINT group (49.87 ± 7.55E) had the lowest mean σ. All groups showed a decrease in σ after TC, except for PRINT. The CRTC showed the lowest Weibull modulus. The AR showed higher roughness than BIS. Porosity revealed that the AR (1.369%) and BIS (6.339%) presented the highest porosity, and the CAD (0.002%) had the lowest porosity. Cell adhesion was significantly different between the CR (6.81) and CAD (6.37). CONCLUSION: Thermocycling reduced the flexural strength of most provisional materials, except for 3D-printed resin. However, it did not influence the surface roughness. The CR showed higher microbiological adherence than CAD group. The BIS group reached the highest porosity while the CAD group had the lowest values. CLINICAL RELEVANCE: 3D-printed resins are promising materials for clinical applications because they have good mechanical properties and low fungal adhesion.

The Effects of NAM on the Symmetry of the Face and Maxillary Arch in Babies With Unilateral Cleft.

The study aimed to evaluate the effect of nasoalveolar molding (NAM) therapy through reverse engineering, or its absence, to obtain symmetry of the face and maxillary arch. Twenty-six babies with unilateral cleft lip and palate received treatment with NAM, and 12 babies with unilateral cleft lip and palate without presurgical orthopedics (control group). Patients were molded and photographed in 2-stages: the first month of life (T1/pre) and after the use of NAM/before the cheiloplasty (T2/post). In the digital models, the analyses performed were arch perimeter, arch length, and labial frenulum angle. The photographs allowed us to analyze nasal width, mouth width, columella angle, and nostril area. The results demonstrated that there was an increase in arch perimeter and arch length in control and NAM groups in the T2 period in comparison to T1. Labial frenulum angle was reduced in the NAM group compared to the NAM-T1 and control-T2 periods. Treatment with NAM yielded a reduction in nasal width in the period of T2 compared with T1. Columella angle was enhanced after NAM use in T2 and, was different from control group. The nostril area was reduced in the NAM group in T2 compared with control group. Nasoalveolar molding therapy reduced the labial frenulum angle, contributing to a reduction in the extension of the cleft. The NAM protocol improved facial symmetry, mainly through nasal effects, whereas the absence of orthopedic therapy yielded a commitment to the face and maxillary arch symmetry.

Comparison of Efficacy and Inflammatory Response to Thermoconjunctivoplasty Performed with Cautery or Pulsed 1460 nm Laser.

Conjunctivochalasis is a degenerative condition of the conjunctiva that disrupts tear distribution and causes irritation. Thermoreduction of the redundant conjunctiva is required if symptoms are not relieved with medical therapy. Near-infrared laser treatment is a more controlled method to shrink the conjunctiva than thermocautery. This study compared tissue shrinkage, histology, and postoperative inflammation in thermoconjunctivoplasty performed on the mouse conjunctiva using either thermocautery or pulsed 1460 nm near-infrared laser irradiation. Three sets of experiments were performed on female C57BL/6J mice (n = 72, 26 per treatment group and 20 control) to assess conjunctival shrinkage, wound histology, and inflammation 3 and 10 days after treatment. Both treatments effectively shrunk the conjunctiva, but thermocautery caused greater epithelial damage. Thermocautery caused greater infiltration of neutrophils on day 3 and neutrophils and CD11b+ myeloid cells on day 10. The thermocautery group had significantly higher conjunctival expression of IL-1ß on day 3. Expression of chemokine CCL2 was higher in the conjunctiva on day 3 and tear concentrations were higher on day 7 in the laser group. These results suggest that pulsed laser treatment causes less tissue damage and postoperative inflammation than thermocautery while effectively addressing conjunctivochalasis.

Clinical performance of monolithic polymer-infiltrated ceramic and lithium disilicate posterior crowns: A controlled, randomized, and double-blind clinical trial.

STATEMENT OF PROBLEM: The success rate of monolithic polymer-infiltrated ceramic posterior crowns after 1 year is unclear. PURPOSE: The purpose of this controlled, randomized, and double-blind clinical trial was to evaluate the performance of posterior complete crowns in polymer-infiltrated and lithium disilicate ceramics and to assess the impact of oral rehabilitation on esthetic satisfaction, quality of life, and periodontal health. MATERIAL AND METHODS: A total of 33 crowns were provided in 18 participants allocated to 2 groups: Control (Lithium disilicate-IPS e.max CAD; Ivoclar AG) and Experimental (Polymer-infiltrated ceramic-Vita Enamic; Vita Zahnfabrik). The crowns were evaluated before treatment (T0) and after 1 (T1), 6 (T2), and 12 (T3) months by using modified United States Public Health Service (USPHS) criteria, visual analog scales (VASs), oral impacts on daily performances (OIDP), and periodontal parameters. Survival analysis was performed by using Kaplan-Meier followed by the log-rank test (α=.05). The OIDP and USPHS data were analyzed descriptively while VASs for esthetic satisfaction and periodontal parameters were statistically evaluated by using the Mann-Whitney Friedman, and Wilcoxon post hoc tests. RESULTS: For 18 participants with a mean age of 47.2 years, 19 crowns were manufactured in lithium disilicate and 14 in polymer-infiltrated ceramic. The Kaplan-Meier test revealed similar survival rates of 92.5% for polymer-infiltrated ceramic and 94.7% for lithium disilicate (P>.05). The analysis of periodontal parameters revealed a significant increase in the bleeding on probing (BOP) for polymer-infiltrated ceramics (P=.032) but for lithium disilicate, it was not significant (P=.387). CONCLUSIONS: Survival rates between the evaluated materials were not significantly different, with acceptable clinical performance after 1 year of follow-up.

Influence of the postpolymerization type and time on the flexural strength and dimensional stability of 3D printed interim resins.

STATEMENT OF PROBLEM: The mechanical strength of 3-dimensionally (3D) printed interim resins is unclear but influenced by printing parameters. Evidence regarding standardization of the postpolymerization type and time for 3D printed interim resins is sparse. PURPOSE: The purpose of this in vitro study was to evaluate the influence of postpolymerization type and time on flexural strength and dimensional stability of 3D printed resins for interim restorations. MATERIAL AND METHODS: A total of 288 bars were 3D printed (Form 2; Formlabs, stereolithography-SLA, 50 µm, 30 degrees), (25×2×2 mm; International Organization for Standardization-ISO 4049:2019) abraded and randomly divided into 9 groups (n=30) according to postpolymerization (Ultraviolet device-UV; Microwave with water-MWA; Microwave without water-MW) and time (15, 20, and 30 minutes for UV; and 5, 8, and 10 minutes for MW and MWA). Each bar was then measured with digital calipers at 11 points for length, thickness, and width before and after postpolymerization to analyze dimensional stability. The flexural strength was then measured (σ; 980.6 N, 1 mm/minute) and the fractured surfaces were analyzed with scanning electron microscopy. The σ (MPa) data were evaluated by using a 2-way analysis of variance (ANOVA) and the Tukey honestly significant difference (HSD) pairwise comparisons test (α=.05). Dimensional stability data (mm) were analyzed by using the Kruskal-Wallis test and Dwass-Steel-Critchlow-Fligner multiple comparisons. The Weibull analysis was performed with σ data. RESULTS: The 2-way ANOVA revealed that all factors and their interaction were significant for σ (P<.001). The UV groups presented the highest σ values, being statistically higher than all MW and MWA groups. The Weibull analysis revealed that postpolymerization UV groups found the highest values regarding the characteristic strength, although the MW 8-minute group (13.71) found the highest value for the Weibull modulus. Furthermore, the Kruskal-Wallis test revealed that only the postpolymerization factor was significant for dimensional stability (P<.001). The postpolymerization microwave groups found greater expansion variations at all times, with the MW 8-minute group (0.78 ±0.54) presenting the greatest variation in dimensional stability. CONCLUSIONS: UV was determined to be the most suitable type of postpolymerization for interim printed resin among the postpolymerization methods, regardless of the application time. The postpolymerization MW groups found greater variations in dimensional stability.

Modulation of Oxidative Stress and Inflammation in the Aged Lacrimal Gland.

Inflammation and oxidative stress accompany aging. This study investigated the interplay between oxidative stress and inflammation in the lacrimal gland. C57BL/6 mice were used at 2 to 3, 12, and 24 months of age. Nuclear factor erythroid derived-2-related factor 2 (Nrf2)-/- and corresponding wild-type mice were used at 2 to 3 and 12 to 13 months of age. A separate group of 15.5 to 17 months of age C57BL/6 mice received a diet containing an Nrf2 inducer (Oltipraz) for 8 weeks. Aged C57BL/6 lacrimal glands showed significantly greater lymphocytic infiltration, higher levels of MHC II, IFN-γ, IL-1ß, TNF-α, and cathepsin S (Ctss) mRNA transcripts, and greater nitrotyrosine and 4-hydroxynonenal protein. Young Nrf2-/- mice showed an increase in IL-1ß, IFN-γ, MHC II, and Ctss mRNA transcripts compared with young wild-type mice and greater age-related changes at 12 to 13 months of age. Oltipraz diet significantly decreased nitrotyrosine and 4-hydroxynonenal and decreased the expression of IL-1ß and TNF-α mRNA transcripts, while decreasing the frequency of CD45+CD4+ cells in lacrimal glands and significantly increasing conjunctival goblet cell density compared with a standard diet. The findings provide novel insight into the development of chronic, low-grade inflammation and oxidative stress in age-related dry eye. New therapies targeting oxidative stress pathways will be valuable in treating age-related dry eye.

Naturally acquired antibody response to a Plasmodium falciparum chimeric vaccine candidate GMZ2.6c and its components (MSP-3, GLURP, and Pfs48/45) in individuals living in Brazilian malaria-endemic areas.

BACKGROUND: The GMZ2.6c malaria vaccine candidate is a multi-stage Plasmodium falciparum chimeric protein which contains a fragment of the sexual-stage Pfs48/45-6C protein genetically fused to GMZ2, a fusion protein of GLURP and MSP-3, that has been shown to be well tolerated, safe and immunogenic in clinical trials performed in a malaria-endemic area of Africa. However, there is no data available on the antigenicity or immunogenicity of GMZ2.6c in humans. Considering that circulating parasites can be genetically distinct in different malaria-endemic areas and that host genetic factors can influence the immune response to vaccine antigens, it is important to verify the antigenicity, immunogenicity and the possibility of associated protection in individuals living in malaria-endemic areas with different epidemiological scenarios. Herein, the profile of antibody response against GMZ2.6c and its components (MSP-3, GLURP and Pfs48/45) in residents of the Brazilian Amazon naturally exposed to malaria, in areas with different levels of transmission, was evaluated. METHODS: This study was performed using serum samples from 352 individuals from Cruzeiro do Sul and Mâncio Lima, in the state of Acre, and Guajará, in the state of Amazonas. Specific IgG, IgM, IgA and IgE antibodies and IgG subclasses were detected by Enzyme-Linked Immunosorbent Assay. RESULTS: The results showed that GMZ2.6c protein was widely recognized by naturally acquired antibodies from individuals of the Brazilian endemic areas with different levels of transmission. The higher prevalence of individuals with antibodies against GMZ2.6c when compared to its individual components may suggest an additive effect of GLURP, MSP-3, and Pfs48/45 when inserted in a same construct. Furthermore, naturally malaria-exposed individuals predominantly had IgG1 and IgG3 cytophilic anti-GMZ2.6c antibodies, an important fact considering that the acquisition of anti-malaria protective immunity results from a delicate balance between cytophilic/non-cytophilic antibodies. Interestingly, anti-GMZ2.6c antibodies seem to increase with exposure to malaria infection and may contribute to parasite immunity. CONCLUSIONS: The data showed that GMZ2.6c protein is widely recognized by naturally acquired antibodies from individuals living in malaria-endemic areas in Brazil and that these may contribute to parasite immunity. These data highlight the importance of GMZ2.6c as a candidate for an anti-malarial vaccine.

River Winds and Transport of Forest Volatiles in the Amazonian Riparian Ecoregion.

Volatile organic compounds (VOCs) emitted from forests are important chemical components that affect ecosystem functioning, atmospheric chemistry, and regional climate. Temperature differences between a forest and an adjacent river can induce winds that influence VOC fate and transport. Quantitative observations and scientific understanding, however, remain lacking. Herein, daytime VOC datasets were collected from the surface up to 500 m over the "Rio Negro" river in Amazonia. During time periods of river winds, isoprene, α-pinene, and ß-pinene concentrations increased by 50, 60, and 80% over the river, respectively. The concentrations at 500 m were up to 80% greater compared to those at 100 m because of the transport path of river winds. By comparison, the concentration of methacrolein, a VOC oxidation product, did not depend on river winds or height. The differing observations for primary emissions and oxidation products can be explained by the coupling of timescales among emission, reaction, and transport. This behavior was captured in large-eddy simulations with a coupled chemistry model. The observed and simulated roles of river winds in VOC fate and transport highlight the need for improved representation of these processes in regional models of air quality and chemistry-climate coupling.

Amazon boundary layer aerosol concentration sustained by vertical transport during rainfall.

The nucleation of atmospheric vapours is an important source of new aerosol particles that can subsequently grow to form cloud condensation nuclei in the atmosphere. Most field studies of atmospheric aerosols over continents are influenced by atmospheric vapours of anthropogenic origin (for example, ref. 2) and, in consequence, aerosol processes in pristine, terrestrial environments remain poorly understood. The Amazon rainforest is one of the few continental regions where aerosol particles and their precursors can be studied under near-natural conditions, but the origin of small aerosol particles that grow into cloud condensation nuclei in the Amazon boundary layer remains unclear. Here we present aircraft- and ground-based measurements under clean conditions during the wet season in the central Amazon basin. We find that high concentrations of small aerosol particles (with diameters of less than 50 nanometres) in the lower free troposphere are transported from the free troposphere into the boundary layer during precipitation events by strong convective downdrafts and weaker downward motions in the trailing stratiform region. This rapid vertical transport can help to maintain the population of particles in the pristine Amazon boundary layer, and may therefore influence cloud properties and climate under natural conditions.

Intermediate-scale horizontal isoprene concentrations in the near-canopy forest atmosphere and implications for emission heterogeneity.

The emissions, deposition, and chemistry of volatile organic compounds (VOCs) are thought to be influenced by underlying landscape heterogeneity at intermediate horizontal scales of several hundred meters across different forest subtypes within a tropical forest. Quantitative observations and scientific understanding at these scales, however, remain lacking, in large part due to a historical absence of canopy access and suitable observational approaches. Herein, horizontal heterogeneity in VOC concentrations in the near-canopy atmosphere was examined by sampling from an unmanned aerial vehicle (UAV) flown horizontally several hundred meters over the plateau and slope forests in central Amazonia during the morning and early afternoon periods of the wet season of 2018. Unlike terpene concentrations, the isoprene concentrations in the near-canopy atmosphere over the plateau forest were 60% greater than those over the slope forest. A gradient transport model constrained by the data suggests that isoprene emissions differed by 220 to 330% from these forest subtypes, which is in contrast to a 0% difference implemented in most present-day biosphere emissions models (i.e., homogeneous emissions). Quantifying VOC concentrations, emissions, and other processes at intermediate horizontal scales is essential for understanding the ecological and Earth system roles of VOCs and representing them in climate and air quality models.

Distinct behavior of bovine-associated staphylococci species in their ability to resist phagocytosis and trigger respiratory burst activity by blood and milk polymorphonuclear leukocytes in dairy cows.

Mastitis affects a high proportion of dairy cows and is still one of the greatest challenges faced by the dairy industry. Staphylococcal bacteria remain the most important cause of mastitis worldwide. We investigated how distinct staphylococcal species evade some critical host defense mechanisms, which may dictate the establishment, severity, and persistence of infection and the outcome of possible therapeutic and prevention interventions. Thus, the present study investigated variations among distinct bovine-associated staphylococci in their capability to resist phagocytosis and to trigger respiratory burst activity of blood and milk polymorphonuclear neutrophil leukocytes (PMNL) in dairy cows. To do so, PMNL of 6 primiparous and 6 multiparous dairy cows were used. A collection of 38 non-aureus staphylococci (NAS) and 12 Staphylococcus aureus were included. The phagocytosis and intracellular reactive oxygen species (ROS) production by blood and milk PMNL were analyzed by flow cytometry. Phagocytosis, by both blood and milk PMNL, did not differ between S. aureus and NAS as a group, although within-NAS species differences were observed. Staphylococcus chromogenes (a so-called milk-adapted NAS species) better resisted phagocytosis by blood PMNL than the so-called environmental (i.e., Staphylococcus fleurettii) and opportunistic (i.e., Staphylococcus haemolyticus) NAS species. Otherwise, S. haemolyticus was better phagocytosed by blood PMNL than S. aureus, S. fleurettii, and S. chromogenes. No influence of the origin of the isolates within the staphylococci species in the resistance to phagocytosis by blood and milk PMNL was found. Overall, both S. aureus and NAS did not inhibit intracellular ROS production in blood and milk PMNL. Non-aureus staphylococci induced fewer ROS by milk PMNL than S. aureus, which was not true for blood PMNL, although species-specific differences in the intensity of ROS production were observed. Staphylococcus chromogenes induced more blood PMNL ROS than S. fleurettii and S. haemolyticus, and as much as S. aureus. Conversely, S. chromogenes induced fewer milk PMNL ROS than S. aureus. The origin of the isolates within the staphylococci species did not affect the ROS production by blood and milk PMNL. In conclusion, our study showed differences in staphylococci species in evading phagocytosis and triggering ROS production, which may explain the ability of some staphylococci species (i.e., S. aureus and S. chromogenes) to cause persistent infection and induce inflammation.

Stage II and stage III periodontitis clinical burdens of HIV-1 undergoing antiretroviral therapy.

OBJECTIVES: The aim of this retrospective cross-sectional study was to estimate the association of HIV-1 infection under highly active antiretroviral treatment (HAART) on the clinical parameters of periodontitis. MATERIALS AND METHODS: A total of 205 patients were divided in two groups: 74 HIV + and 131 HIV - . Periodontal probing depth (PPD), clinical attachment loss (CAL), bleeding on probing (BOP), and visible supragingival biofilm (VSB) were recorded. The association of HIV-1 infection with the presence of at least 3 sites with PPD ≥ 5 mm and/or CAL ≥ 4 mm in non-adjacent teeth was estimated using binary logistic regression models. RESULTS: The variables HIV-1 infection (OR = 5.53, p < 0.0001, 95% CI: 2.45-13.64), age [range 35-50 years old (OR = 5.73, p < 0.0001, 95% CI: 2.49-13.20); > 50 years old (OR = 6.29, p = 0.002, 95% CI: 1.94-20.42)], and VSB (OR = 23.68, p < 0.0001, 95% CI: 8.07-69.53) showed a significant direct association with BOP outcome. CONCLUSIONS: HIV-1 infection under HAART did not have association with the presence of at least 3 sites with PPD ≥ 5 mm and/or CAL ≥ 4 mm. However, HIV patients on HAART had direct association of HIV-1 infection with BOP and an inverse association with PPD. CLINICAL RELEVANCE: These results support that monitoring gingival bleeding associated with oral prophylaxis would be beneficial in the prevention and management of periodontitis in HIV-1 patients on HAART.

Fatigue strength of 5Y-FSZ: glazing and polishing effects.

OBJECTIVE: The aim of this study was to evaluate the effect of four different finishing procedures on the fatigue strength of a fully stabilized zirconia (5Y-FSZ) material. MATERIALS AND METHODS: Disc-shaped specimens of a 5Y-FSZ (Katana UTML, Kuraray Noritake) were made (ISO 6872-2015), grinded with 600- and 1200-grit silicon carbide paper, sintered as recommended, and randomly assigned into four groups according to the finishing technique: C (control, as-sintered), P (polished with polishing rubbers), G (glaze application - powder/liquid technique), and PG (polished with polishing rubbers + glaze application - powder/liquid). Then fatigue strength (staircase method), X-ray diffraction (XRD), and scanning electron microscopy (SEM) analyses were performed. RESULTS: The C group presented the lowest fatigue strength, while the PG group presented the highest. The P and G groups presented intermediate behavior, presenting similar statistical results. XRD showed similar crystalline phase patterns for all groups. SEM images revealed some changes in the zirconia surface, with the P group presenting some scratches on the surface, while the scratches in the PG group were filled with the glaze material. CONCLUSION: None of the techniques analyzed in this study impaired the fatigue strength of fully stabilized zirconia. Importantly, the polishing rubbers combined with glaze application (PG group) improved its fatigue strength. CLINICAL RELEVANCE: The polishing rubbers followed by glaze application improve the fatigue strength in ultra-translucent zirconia.

Biaxial flexure strength and physicochemical characterization of a CAD/CAM lithium disilicate ceramic: effect of etching time, silane, and adhesive applications.

OBJECTIVE: To evaluate the effect of different acid etching time and bonding agent (silane and/or adhesive system) on biaxial flexural strength and physico-chemical properties of a lithium disilicate ceramic. MATERIAL AND METHODS: One hundred twenty ceramic discs were made and divided into 8 groups (n = 15) according to factors "etching time" (20 and 120 s) with hydrofluoric acid (HF) and "bonding agent" (C, no bonding agent; S, silane, A, adhesive; and SA, silane + adhesive). After surface treatment, a resin cement layer was applied to the surface and all specimens were subjected to biaxial flexural strength (BFS) test with treated surfaces loaded in tension (1 mm/min). The Weibull analyses and complementary analyses were also performed. Statistical analysis was done with 2-way ANOVA and the Tukey test (α = 0.05). RESULTS: ANOVA revealed that the factors "etching time" (p = 0.0003) and "bonding agent" (p = 0.007) were statistically significant. In the overall analysis, the HF120S group (272.02 ± 35.30A MPa) presented significantly higher BFS than that of HF120C (218.45 ± 17.15CD MPa) and HF20S (228.40 ± 37.83BCDMPa). On the other hand, the HF20A group (208.92 ± 31.16D MPa) had significantly lower BFS than HF120S (272.02 ± 35.30A), HF120A (254.42 ± 26.87ABC) and HF120SA (259.30 ± 36.55AB) groups (Tukey). The Weibull modulus (m) of all groups was significantly different from each other (p = 0.000). CONCLUSIONS: Regardless of etching time, the application of silane alone is sufficient to increase the flexural strength of glass ceramic, eliminating the need for the application of adhesive systems. Moreover, if only silane or adhesive is applied, 120-s HF application should increase the flexural resistance of the lithium disilicate ceramic. CLINICAL SIGNIFICANCE: Applications of adhesive systems after silanization can be suppressed from the surface treatment protocol of glass ceramics, since it does not improve their mechanical strength.