RESUMO
Scale-up and transfer of lyophilization processes remain very challenging tasks considering the technical challenges and the high cost of the process itself. The challenges in scale-up and transfer were discussed in the first part of this paper and include vial breakage during freezing at commercial scale, cake resistance differences between scales, impact of differences in refrigeration capacities, and geometry on the performance of dryers. The second part of this work discusses successful and unsuccessful practices in scale-up and transfer based on the experience of the authors. Regulatory aspects of scale-up and transfer of lyophilization processes were also outlined including a topic on the equivalency of dryers. Based on an analysis of challenges and a summary of best practices, recommendations on scale-up and transfer of lyophilization processes are given including projections on future directions in this area of the freeze drying field. Recommendations on the choice of residual vacuum in the vials were also provided for a wide range of vial capacities.
Assuntos
Liofilização , Transferência de Tecnologia , Tecnologia Farmacêutica , Temperatura , Guias como AssuntoRESUMO
The freeze-drying process scale-up and transfer remain a complicated and non-uniform practice. We summarized inefficient and good practices in these papers and provided some practical advice. It was demonstrated that using the same process set points/times in laboratory and commercial scale dryers may lead to loss of product quality (collapse or vial breakage). The emerging modeling approach demonstrated practical advantages. However, the upfront generation of some input parameters (vial heat transfer coefficient, minimum controllable pressure, and maximum sublimation rate) is essential for model utilization. While the primary drying step can be transferred with a high degree of confidence (e.g., using modeling), and secondary drying is usually fairly straightforward, predicting potential changes in product behavior during freezing remains challenging.
Assuntos
Dessecação , Temperatura Alta , LiofilizaçãoRESUMO
The objective of this investigation was to evaluate two methods for measuring the maximum sublimation rate that a freeze-dryer will support-the minimum controllable pressure method and the choke point method. Both methods gave equivalent results, but the minimum controllable pressure method is preferred, since it is easier, faster, and less subjective. The ratio of chamber pressure to condenser pressure corresponding to the onset of choked flow was considerably higher in this investigation (up to about 20:1) than in previously published reports. This ratio was not affected by the location of the pressure gauge on the condenser; that is, on the foreline of the vacuum pump versus on the body of the condenser itself. The total water loss due to sublimation as measured by tunable diode laser absorption spectroscopy was consistently within 5% of gravimetrically determined weight loss, regardless of whether the measurement took place during choked versus non-choked process conditions.
Assuntos
Liofilização/instrumentação , Pressão , Análise Espectral , Temperatura , Água/químicaRESUMO
This work describes the lyophilization process validation and consists of two parts. Part one (Part I: Process Design and Modeling) focuses on the process design and is described in the previous paper, while the current paper is devoted to process qualification and continued process verification. The goal of the study is to show the cutting edge of lyophilization validation based on the integrated community-based opinion and the industrial perspective. This study presents best practices for batch size determination and includes the effect of batch size on drying time, process parameters selection strategies, and batch size overage to compensate for losses during production. It also includes sampling strategies to demonstrate batch uniformity as well as the use of statistical models to ensure adequate sampling. Based on the LyoHUB member organizations survey, the best practices in determining the number of PPQ runs are developed including the bracketing approach with minimum and maximum loads. Standard practice around CQA and CPP selection is outlined and shows the advantages of using control charts and run charts for process trending and quality control. The case studies demonstrating the validation strategy for monoclonal antibody and the impact of the loading process on the lyophilization cycle and product quality as well as the special case of lyophilization for dual-chamber cartridge system are chosen to illustrate the process validation. The standard practices in the validation of the lyophilization process, special lyophilization processes, and their impact on the validation strategy are discussed.
Assuntos
Dessecação , Modelos Estatísticos , Liofilização , Controle de Qualidade , TemperaturaRESUMO
This work describes lyophilization process validation and consists of two parts. Part I focuses on the process design and is described in the current paper, while part II is devoted to process qualification and continued process verification. The intent of these articles is to provide readers with recent updates on lyophilization validation in the light of community-based combined opinion on the process and reflect the industrial prospective. In this paper, the design space approach for process design is described in details, and examples from practice are provided. The approach shows the relationship between the process inputs; it is based on first principles and gives a thorough scientific understanding of process and product. The lyophilization process modeling and scale-up are also presented showing the impact of facility, equipment, and vial heat transfer coefficient. The case studies demonstrating the effect of batch sizes, fill volume, and dose strength to show the importance of modeling as well as the effect of controlled nucleation on product resistance are discussed.
Assuntos
Temperatura Alta , Tecnologia Farmacêutica , Liofilização , Estudos Prospectivos , TemperaturaRESUMO
An emerging approach to process development of a lyophilized pharmaceutical product is to construct a graphical design space for primary drying as an aid to process optimization. The purpose of this paper is to further challenge the assumption in earlier work that the maximum values of the resistance of dried product layer, Rp, is approximately constant and is independent of process conditions within the "acceptable" region of the design space. Three model formulations containing bovine serum albumin as the model protein were chosen to represent: (a) an amorphous system, (b) a crystalline system, and (c) a mixed system where both an amorphous and a crystalline component were present. Low temperature differential scanning calorimetry (DSC) and freeze dry microscopy (FDM) experiments were conducted to estimate critical product temperature. A conservative lyophilization cycle was conducted for each formulation to collect mass flow data and individual design spaces were then established. A series of lyophilization cycles were then conducted using process conditions that resided within the individual design space and the resultant product temperature and resistance of dried product layer (Rp) values were compared between the individual cycles within each formulation. The data indicated that the Rp was component dependent with the mannitol formulation exhibiting higher Rp values than the sucrose formulation. Interestingly, when mannitol was retained amorphous, the formulation exhibited a lower Rp, similar to that of the sucrose formulation. The mixed formulation exhibited intermediate Rp values. Crystallization of mannitol is hypothesized to facilitate a decrease in the size of the ice porous structure by making the water vapor flow path tortuous, thereby increasing the Rp of mannitol formulations. Within the "acceptable" zone of the individual design space, Rp was dependent on the process condition with more aggressive shelf temperature cycles resulting in lower Rp. Specific Surface Area measurements of freeze-dried solids demonstrated that more aggressive conditions resulted in smaller surface area. Freeze-dried solids of crystalline formulations consistently exhibited higher specific surface area than the amorphous formulations.
Assuntos
Dessecação , Manitol , Liofilização/métodos , Varredura Diferencial de Calorimetria , Temperatura , Sacarose/químicaRESUMO
The high propensity of mannitol to crystallize in frozen solutions along with its high eutectic temperature enabling higher primary drying temperatures makes it a good bulking agent. In protein formulations, addition of a sugar (sucrose) that has the ability to remain amorphous throughout processing as well as storage is imperative to retain the protein in its native state. It is well known that in the presence of amorphous excipients and protein, mannitol can crystallize as a mixture of anhydrous polymorphs - α-, ß- and δ-forms and a hemihydrate form [mannitol hemihydrate (MHH); C6H14O6·0.5H2O]. The conditions of formation of MHH due to processing and formulation variables are well established in the literature. However, MHH's dehydration kinetics on storage and its impact on the stability of a protein has not been systematically evaluated. The overall objective was to identify conditions (temperature and humidity) at which MHH can dehydrate on storage and the consequences of the release of associated water on sucrose phase behavior and protein stability. In a mannitol-sucrose-protein lyophile, the purpose of this study was (i) to investigate the dehydration behavior of MHH (ii) to determine the influence of dehydration on sucrose crystallization and (iii) the effect of moisture released due to MHH dehydration on model protein (Bovine serum albumin, BSA or Human serum albumin, HSA) aggregation. MHH dehydration and sucrose crystallization was observed in cases where the relative humidity was ≥ 55% (open vials). A relative humidity of ≤ 33% RH prevented MHH dehydration while retaining sucrose amorphous. No protein aggregation was observed irrespective of presence of MHH or its dehydration.
Assuntos
Manitol , Sacarose , Varredura Diferencial de Calorimetria , Desidratação , Excipientes/química , Liofilização , Humanos , Manitol/química , Estabilidade Proteica , Soroalbumina Bovina , Sacarose/químicaRESUMO
Antibody drug conjugates (ADCs) have been at the forefront in cancer therapy due to their target specificity. All the FDA approved ADCs are developed in lyophilized form to minimize instability associated with the linker that connects the cytotoxic drug and the antibody during shipping and storage. We present here solid-state hydrogen-deuterium exchange with mass spectrometric analysis (ssHDX-MS) as a tool to analyze protein structure and matrix interactions for formulations of an ADC with and without commonly used excipients. We compared results of the ssHDX-MS with accelerated stability results using size-exclusion chromatography and determined that the former technique was able to successfully identify the destabilizing effects of mannitol and polysorbate 80. In comparison, Fourier-transform infrared spectroscopy results were inconclusive. The agreement between ssHDX-MS and stressed stability studies supports the potential of ssHDX-MS as a method of predicting relative stability of different formulations.
Assuntos
Medição da Troca de Deutério , Imunoconjugados , Deutério , Estabilidade de Medicamentos , Liofilização , Hidrogênio , Espectrometria de MassasRESUMO
The objective of this research was to study the atypical secondary drying dynamics observed during the freeze-drying of a formulation consisting of mannitol, disaccharide, and sodium chloride, where "bursts" of water vapor release were observed during secondary drying as detected by comparative pressure measurement. "Thief" samples were removed at the end of primary drying and during secondary drying as the shelf temperature was increased in a stepwise fashion. These samples were examined by X-ray powder diffraction and thermal analysis. From the X-ray powder diffraction data, we determined that mannitol crystallized predominantly as its hemihydrate. The physical state of mannitol changed from the hemihydrate form to anhydrous forms during secondary drying. Investigation of the effect of excipients on mannitol crystallization demonstrated that sodium chloride (at 225 mM, 1.3% w/v) had the greatest influence on hemihydrate crystallization, followed by trehalose and sucrose. However, only negligible hemihydrate formation was observed when mannitol was freeze-dried either by itself or in the presence of 150 mM sodium chloride and no hemihydrate in the presence of 75 mM sodium chloride. In general, a combination of a disaccharide and sodium chloride promoted the hemihydrate formation to a greater extent than the individual components. Comparative pressure measurement was demonstrated to be an effective tool to monitor mannitol hemihydrate dehydration during secondary drying.
Assuntos
Manitol/química , Proteínas/química , Química Farmacêutica/métodos , Cristalização/métodos , Dessecação/métodos , Dissacarídeos/química , Excipientes/química , Liofilização/métodos , Pós/química , Cloreto de Sódio/química , Sacarose/química , Temperatura , Trealose/química , Difração de Raios X/métodosRESUMO
[Structure: see text] An advanced intermediate in our planned synthesis of mitomycin C has been acquired in nine steps from tert-butyl glyoxylate. The aziridinyl pyrrolidine and quinone subunits are coupled regioselectively to arrive at an enamine that is prepared for C10 homologation.
Assuntos
Produtos Biológicos/síntese química , Mitomicina/síntese químicaRESUMO
A concise synthesis of a highly functionalized intermediate lacking only C10 of the mitomycin backbone is described. The key to this development is the Brønsted acid-catalyzed aza-Darzens reaction used to forge the cis-aziridine. Additionally an oxidative ketalization fortuitously occurs during the quinone-enamine coupling step, leading to an orthogonally protected hydroquinone.
Assuntos
Antibióticos Antineoplásicos/síntese química , Aziridinas/síntese química , Mitomicina/síntese química , Antibióticos Antineoplásicos/química , Aziridinas/química , Catálise , Cristalografia por Raios X , Mitomicina/química , Modelos Moleculares , EstereoisomerismoRESUMO
Two nonnatural proline derivatives, (S)- and (R)-7-azaindoline α-amino acid have been prepared and isolated as their trifluoroacetate salt on gram scale. The convergent sequence (6 steps from 2-bromopyridine) employs a combination of enantioselective phase transfer catalyzed glycine alkylation and free radical-mediated aryl amination. Implementation of the solid-liquid phase transfer conditions requires manual pulverization of cesium hydroxide, efficient mechanical stirring, and effective low temperature control. This large scale free radical cyclization protocol replaces benzene solvent with toluene without complication, and the crystalline nature of the intermediates and final product enables straightforward purification at each stage, including enantiomeric enrichment (89 to >99% ee for 4b).