Stability Assessment of p-i-n Perovskite Photovoltaic Mini-Modules Utilizing Different Top Metal Electrodes.

Long-term stability is one of the major challenges for p-i-n type perovskite solar modules (PSMs). Here, we demonstrate the fabrication of fully laser-patterned series interconnected p-i-n perovskite mini-modules, in which either single Cu or Ag layers are compared with Cu/Au metal-bilayer top electrodes. According to the scanning electron microscopy measurements, we found that Cu or Ag top electrodes often exhibit flaking of the metal upon P3 (top contact removal) laser patterning. For Cu/Au bilayer top electrodes, metal flaking may cause intermittent short-circuits between interconnected sub-cells during operation, resulting in fluctuations in the maximum power point (MPP). Here, we demonstrate Cu/Au metal-bilayer-based PSMs with an efficiency of 18.9% on an active area of 2.2 cm2 under continuous 1-sun illumination. This work highlights the importance of optimizing the top-contact composition to tackle the operational stability of mini-modules, and could help to improve the feasibility of large-area module deployment for the commercialization of perovskite photovoltaics.

Compositional and Interfacial Engineering Yield High-Performance and Stable p-i-n Perovskite Solar Cells and Mini-Modules.

Through the optimization of the perovskite precursor composition and interfaces to selective contacts, we achieved a p-i-n-type perovskite solar cell (PSC) with a 22.3% power conversion efficiency (PCE). This is a new performance record for a PSC with an absorber bandgap of 1.63 eV. We demonstrate that the high device performance originates from a synergy between (1) an improved perovskite absorber quality when introducing formamidinium chloride (FACl) as an additive in the "triple cation" Cs0.05FA0.79MA0.16PbBr0.51I2.49 (Cs-MAFA) perovskite precursor ink, (2) an increased open-circuit voltage, VOC, due to reduced recombination losses when using a lithium fluoride (LiF) interfacial buffer layer, and (3) high-quality hole-selective contacts with a self-assembled monolayer (SAM) of [2-(9H-carbazol-9-yl)ethyl]phosphonic acid (2PACz) on ITO electrodes. While all devices exhibit a high performance after fabrication, as determined from current-density voltage, J-V, measurements, substantial differences in device performance become apparent when considering longer-term stability data. A reduced long-term stability of devices with the introduction of a LiF interlayer is compensated for by using FACl as an additive in the metal-halide perovskite thin-film deposition. Optimized devices maintained about 80% of the initial average PCE during maximum power point (MPP) tracking for >700 h. We scaled the optimized device architecture to larger areas and achieved fully laser patterned series-interconnected mini-modules with a PCE of 19.4% for a 2.2 cm2 active area. A robust device architecture and reproducible deposition methods are fundamental for high performance and stable large-area single junction and tandem modules based on PSCs.

Switching adhesion forces by crossing the metal-insulator transition in Magnéli-type vanadium oxide crystals.

Magnéli-type vanadium oxides form the homologous series V(n)O(2) (n) (-1) and exhibit a temperature-induced, reversible metal-insulator first order phase transition (MIT). We studied the change of the adhesion force across the transition temperature between the cleavage planes of various vanadium oxide Magnéli phases (n = 3 … 7) and spherical titanium atomic force microscope (AFM) tips by systematic force-distance measurements with a variable-temperature AFM under ultrahigh vacuum conditions (UHV). The results show, for all investigated samples, that crossing the transition temperatures leads to a distinct change of the adhesion force. Low adhesion corresponds consistently to the metallic state. Accordingly, the ability to modify the electronic structure of the vanadium Magnéli phases while maintaining composition, stoichiometry and crystallographic integrity, allows for relating frictional and electronic material properties at the nano scale. This behavior makes the vanadium Magnéli phases interesting candidates for technology, e.g., as intelligent devices or coatings where switching of adhesion or friction is desired.

Ultrathin SiO(2) layers on Si(111): preparation, interface gap states and the influence of passivation.

An essential prerequisite for the successful application of Si/SiO(2) nanostructures in photovoltaics is the realization of well-defined and abrupt interfaces with low densities of interface gap states. Here, a complete in situ process from preparation and hydrogen passivation to interface gap state analysis by near-UV photoelectron spectroscopy without breaking ultrahigh vacuum (UHV) conditions is introduced. It is demonstrated that by RF plasma oxidation of Si(111) substrates with thermalized neutral oxygen atoms, ultrathin SiO(2) layers can be realized with compositionally and structurally abrupt Si/SiO(2) interfaces and a minimal amount of intermediate oxidation states bridging the transition from Si to SiO(2). Plasma oxidized samples have significantly lower interface gap states than samples oxidized by thermal oxidation at 850 °C. Interface gap state densities were further reduced by in situ hydrogen plasma passivation with nearly thermalized H atoms. The resulting reduction of interface recombination velocity and the increase of effective majority and minority carrier lifetimes are revealed by constant photocurrent measurements and quasi-steady-state photoconductance, respectively.

Cluster assembled nanostructures: designing interface properties.

Overlayer structures can be formed on surfaces by the deposition of preformed clusters from the gas phase containing from only a few up to a few hundred atoms. By this method, nanostructures with novel chemical and physical properties can be stabilized. This article presents the results obtained using the simple molecular cluster Sb4 as the precursor for deposition and nanoparticle assembly on various surfaces, and under various conditions. A rich variety of phenomena is observed and discussed.