RESUMO
Perovskite solar cells (PSCs) comprise a solid perovskite absorber sandwiched between several layers of different charge-selective materials, ensuring unidirectional current flow and high voltage output of the devices1,2. A 'buffer material' between the electron-selective layer and the metal electrode in p-type/intrinsic/n-type (p-i-n) PSCs (also known as inverted PSCs) enables electrons to flow from the electron-selective layer to the electrode3-5. Furthermore, it acts as a barrier inhibiting the inter-diffusion of harmful species into or degradation products out of the perovskite absorber6-8. Thus far, evaporable organic molecules9,10 and atomic-layer-deposited metal oxides11,12 have been successful, but each has specific imperfections. Here we report a chemically stable and multifunctional buffer material, ytterbium oxide (YbOx), for p-i-n PSCs by scalable thermal evaporation deposition. We used this YbOx buffer in the p-i-n PSCs with a narrow-bandgap perovskite absorber, yielding a certified power conversion efficiency of more than 25%. We also demonstrate the broad applicability of YbOx in enabling highly efficient PSCs from various types of perovskite absorber layer, delivering state-of-the-art efficiencies of 20.1% for the wide-bandgap perovskite absorber and 22.1% for the mid-bandgap perovskite absorber, respectively. Moreover, when subjected to ISOS-L-3 accelerated ageing, encapsulated devices with YbOx exhibit markedly enhanced device stability.
RESUMO
The ethanol oxidation reaction (EOR) is an attractive alternative to the sluggish oxygen evolution reaction in electrochemical hydrogen evolution cells. However, the development of high-performance bifunctional electrocatalysts for both EOR and hydrogen evolution reaction (HER) is a major challenge. Herein, the synthesis of Pd3 Pb@Pt core-shell nanocubes with controlled shell thickness by Pt-seeded epitaxial growth on intermetallic Pd3 Pb cores is reported. The lattice mismatch between the Pd3 Pb core and the Pt shell leads to the expansion of the Pt lattice. The synergistic effects between the tensile strain and the core-shell structures result in excellent electrocatalytic performance of Pd3 Pb@Pt catalysts for both EOR and HER. In particular, Pd3 Pb@Pt with three Pt atomic layers shows a mass activity of 8.60 A mg-1 Pd+Pt for ethanol upgrading to acetic acid and close to 100% of Faradic efficiency for HER. An EOR/HER electrolysis system is assembled using Pd3 Pb@Pt for both the anode and cathode, and it is shown that low cell voltage of 0.75 V is required to reach a current density of 10 mA cm-2 . The present work offers a promising strategy for the development of bifunctional catalysts for hybrid electrocatalytic reactions and beyond.
RESUMO
In the present work, we detail a fast and simple solution-based method to synthesize hexagonal SnSe2 nanoplates (NPLs) and their use to produce crystallographically textured SnSe2 nanomaterials. We also demonstrate that the same strategy can be used to produce orthorhombic SnSe nanostructures and nanomaterials. NPLs are grown through a screw dislocation-driven mechanism. This mechanism typically results in pyramidal structures, but we demonstrate here that the growth from multiple dislocations results in flower-like structures. Crystallographically textured SnSe2 bulk nanomaterials obtained from the hot pressing of these SnSe2 structures display highly anisotropic charge and heat transport properties and thermoelectric (TE) figures of merit limited by relatively low electrical conductivities. To improve this parameter, SnSe2 NPLs are blended here with metal nanoparticles. The electrical conductivities of the blends are significantly improved with respect to bare SnSe2 NPLs, what translates into a three-fold increase of the TE Figure of merit, reaching unprecedented ZT values up to 0.65.
RESUMO
The development of upscalable oxygen evolving electrocatalysts from earth-abundant metals able to operate in neutral or acidic environments and low overpotentials remains a fundamental challenge for the realization of artificial photosynthesis. In this study, we report a highly active phase of heterobimetallic cyanide-bridged electrocatalysts able to promote water oxidation under neutral, basic (pH < 13), and acidic conditions (pH > 1). Cobalt-iron Prussian blue-type thin films, formed by chemical etching of Co(OH)1.0(CO3)0.5·nH2O nanocrystals, yield a dramatic enhancement of the catalytic performance toward oxygen production, when compared with previous reports for analogous materials. Electrochemical, spectroscopic, and structural studies confirm the excellent performance, stability, and corrosion resistance, even when compared with state-of-the-art metal oxide catalysts under moderate overpotentials and in a remarkably large pH range, including acid media where most cost-effective water oxidation catalysts are not useful. The origin of the superior electrocatalytic activity toward water oxidation appears to be in the optimized interfacial matching between catalyst and electrode surface obtained through this fabrication method.
RESUMO
High-quality perovskite films are essential for achieving high performance of optoelectronic devices; However, solution-processed perovskite films are known to suffer from compositional and structural inhomogeneity due to lack of systematic control over the kinetics during the formation. Here, the microscopic homogeneity of perovskite films is successfully enhanced by modulating the conversion reaction kinetics using a catalyst-like system generated by a foaming agent. The chemical and structural evolution during this catalytic conversion is revealed by a multimodal synchrotron toolkit with spatial resolutions spanning many length scales. Combining these insights with computational investigations, a cyclic conversion pathway model is developed that yields exceptional perovskite homogeneity due to enhanced conversion, having a power conversion efficiency of 24.51% for photovoltaic devices. This work establishes a systematic link between processing of precursor and homogeneity of the perovskite films.
RESUMO
The adsorption and activation of CO2 on the electrode interface is a prerequisite and key step for electrocatalytic CO2 reduction reaction (eCO2 RR). Regulating the interfacial microenvironment to promote the adsorption and activation of CO2 is thus of great significance to optimize overall conversion efficiency. Herein, a CO2-philic hydroxyl coordinated ZnO (ZnO-OH) catalyst is fabricated, for the first time, via a facile MOF-assisted method. In comparison to the commercial ZnO, the as-prepared ZnO-OH exhibits much higher selectivity toward CO at lower applied potential, reaching a Faradaic efficiency of 85% at -0.95 V versus RHE. To the best of our knowledge, such selectivity is one of the best records in ZnO-based catalysts reported till date. Density functional theory calculations reveal that the coordinated surficial -OH groups are not only favorable to interact with CO2 molecules but also function in synergy to decrease the energy barrier of the rate-determining step and maintain a higher charge density of potential active sites as well as inhibit undesired hydrogen evolution reaction. Our results indicate that engineering the interfacial microenvironment through the introduction of CO2-philic groups is a promising way to achieve the global optimization of eCO2 RR via promoting adsorption and activation of CO2.
RESUMO
Using a combination of in situ bulk and surface characterization techniques, we provide atomic-scale insight into the complex surface and bulk dynamics of a LaNiO3 perovskite material during heating in vacuo. Driven by the outstanding activity LaNiO3 in the methane dry reforming reaction (DRM), attributable to the decomposition of LaNiO3 during DRM operation into a Ni//La2O3 composite, we reveal the Ni exsolution dynamics both on a local and global scale by in situ electron microscopy, in situ X-ray diffraction and in situ X-ray photoelectron spectroscopy. To reduce the complexity and disentangle thermal from self-activation and reaction-induced effects, we embarked on a heating experiment in vacuo under comparable experimental conditions in all methods. Associated with the Ni exsolution, the remaining perovskite grains suffer a drastic shrinkage of the grain volume and compression of the structure. Ni particles mainly evolve at grain boundaries and stacking faults. Sophisticated structure analysis of the elemental composition by electron-energy loss mapping allows us to disentangle the distribution of the different structures resulting from LaNiO3 decomposition on a local scale. Important for explaining the DRM activity, our results indicate that most of the Ni moieties are oxidized and that the formation of NiO occurs preferentially at grain edges, resulting from the reaction of the exsolved Ni particles with oxygen released from the perovskite lattice during decomposition via a spillover process from the perovskite to the Ni particles. Correlating electron microscopy and X-ray diffraction data allows us to establish a sequential two-step process in the decomposition of LaNiO3 via a Ruddlesden-Popper La2NiO4 intermediate structure. Exemplified for the archetypical LaNiO3 perovskite material, our results underscore the importance of focusing on both surface and bulk characterization for a thorough understanding of the catalyst dynamics and set the stage for a generalized concept in the understanding of state-of-the art catalyst materials on an atomic level.
RESUMO
The shuttling behavior and sluggish conversion kinetics of the intermediate lithium polysulfides (LiPS) represent the main obstructions to the practical application of lithium-sulfur batteries (LSBs). Herein, a 1D π-d conjugated metal-organic framework (MOF), Ni-MOF-1D, is presented as an efficient sulfur host to overcome these limitations. Experimental results and density functional theory calculations demonstrate that Ni-MOF-1D is characterized by a remarkable binding strength for trapping soluble LiPS species. Ni-MOF-1D also acts as an effective catalyst for S reduction during the discharge process and Li2 S oxidation during the charging process. In addition, the delocalization of electrons in the π-d system of Ni-MOF-1D provides a superior electrical conductivity to improve electron transfer. Thus, cathodes based on Ni-MOF-1D enable LSBs with excellent performance, for example, impressive cycling stability with over 82% capacity retention over 1000 cycles at 3 C, superior rate performance of 575 mAh g-1 at 8 C, and a high areal capacity of 6.63 mAh cm-2 under raised sulfur loading of 6.7 mg cm-2 . The strategies and advantages here demonstrated can be extended to a broader range of π-d conjugated MOFs materials, which the authors believe have a high potential as sulfur hosts in LSBs.
RESUMO
There exists a considerable density of interaggregate grain boundaries (GBs) and intra-aggregate GBs in polycrystalline perovskites. Mitigation of intra-aggregate GBs is equally notable to that of interaggregate GBs as intra-aggregate GBs can also cause detrimental effects on the photovoltaic performances of perovskite solar cells (PSCs). Here, we demonstrate full-scale GB mitigation ranging from nanoscale intra-aggregate to submicron-scale interaggregate GBs, by modulating the crystallization kinetics using a judiciously designed brominated arylamine trimer. The optimized GB-mitigated perovskite films exhibit reduced nonradiative recombination, and their corresponding mesostructured PSCs show substantially enhanced device efficiency and long-term stability under illumination, humidity, or heat stress. The versatility of our strategy is also verified upon applying it to different categories of PSCs. Our discovery not only specifies a rarely addressed perspective concerning fundamental studies of perovskites at nanoscale but also opens a route to obtain high-quality solution-processed polycrystalline perovskites for high-performance optoelectronic devices.
RESUMO
Sustainable electrocatalysis of the oxygen evolution reaction (OER) constitutes a major challenge for the realization of green fuels. Oxides based on Ni and Fe in alkaline media have been proposed to avoid using critical raw materials. However, their ill-defined structures under OER conditions make the identification of key descriptors difficult. Here, we have studied Fe-Ni-Zn spinel oxides, with a well-defined crystal structure, as a platform to obtain general understanding on the key contributions. The OER reaches maximum performance when: (i) Zn is present in the Spinel structure, (ii) very dense, equimolar 1 : 1 : 1 stoichiometry sites appear on the surface as they allow the formation of oxygen vacancies where Zn favors pushing the electronic density that is pulled by the octahedral Fe and tetrahedral Ni redox pair lowering the overpotential. Our work proves cooperative electronic effects on surface active sites as key to design optimum OER electrocatalysts.
RESUMO
In this paper, non-fragile fuzzy sampled-data control is used to analyze the dissipation of uncertain time-varying delay T–S fuzzy system under actuator saturation. First, this paper builds a novel augmented Lyapunov–Krasovskii functional that is more flexible. It involves complete information about the relevant sampled-data patterns. Second, the use of Wirtinger-based integral inequality and Newton–Leibniz formulas yields less conservative results. Next, we discuss the sufficient conditions of the dissipative performance for T–S model, then use the linear matrix inequality (LMI) to give the non-fragile fuzzy sampled-data controller with actuator saturation. Finally, the routine examples show that the advanced approach is effective and feasible and has certain advantages.
RESUMO
Atom-thin transition metal dichalcogenides (TMDs) have emerged as fascinating materials and key structures for electrocatalysis. So far, their edges, dopant heteroatoms and defects have been intensively explored as active sites for the hydrogen evolution reaction (HER) to split water. However, grain boundaries (GBs), a key type of defects in TMDs, have been overlooked due to their low density and large structural variations. Here, we demonstrate the synthesis of wafer-size atom-thin TMD films with an ultra-high-density of GBs, up to ~1012 cm-2. We propose a climb and drive 0D/2D interaction to explain the underlying growth mechanism. The electrocatalytic activity of the nanograin film is comprehensively examined by micro-electrochemical measurements, showing an excellent hydrogen-evolution performance (onset potential: -25 mV and Tafel slope: 54 mV dec-1), thus indicating an intrinsically high activation of the TMD GBs.
RESUMO
The concept of hybrid tandem device structures that combine metal oxides with thin-film semiconducting photoabsorbers holds great promise for large-scale, robust, and cost-effective bias-free photoelectrochemical water splitting (PEC-WS). This work highlights important steps toward the efficient coupling of high-performance hematite photoanodes with multijunction thin-film silicon photocathodes providing high bias-free photocurrent density. The hybrid PEC-WS device is optimized by testing three types of multijunction silicon photocathodes with the hematite photoanode: amorphous silicon (a-Si:H) tandem: a-Si:H/a-Si:H and triple junction with microcrystalline silicon (µc-Si:H): a-Si:H/a-Si:H/µc-Si:H and a-Si:H/µc-Si:H/µc-Si:H. The results provide evidence that the multijunction structures offer high flexibility for hybrid tandem devices with regard to tunable photovoltages and spectral matching. Furthermore, both photoanode and photocathode are tested under various electrolyte and light concentration conditions, respectively, with respect to their photoelectrochemical performance and stability. A 27 % enhancement in the solar-to-hydrogen conversion efficiency is observed upon concentrating light from 100 to 300â mW cm-2 . Ultimately, bias-free water splitting is demonstrated, with a photocurrent density of 4.6â mA cm-2 (under concentrated illumination) paired with excellent operation stability for more than 24â h of the all-earth-abundant and low-cost hematite/silicon tandem PEC-WS device.
RESUMO
Co-Sn solid-solution nanoparticles with Sn crystal structure and tuned metal ratios were synthesized by a facile one pot solution-based procedure involving the initial reduction of a Sn precursor followed by incorporation of Co within the Sn lattice. These nanoparticles were used as anode materials for Li-ion batteries. Among the different compositions tested, Co0.7 Sn and Co0.9 Sn electrodes provided the highest capacities with values above 1500â mAh g-1 at a current density of 0.2â A g-1 after 220â cycles, and up to 800â mAh g-1 at 1.0â A g-1 after 400â cycles. Up to 81 % pseudocapacitance contribution was measured for these electrodes at a sweep rate of 1.0â mV s-1 , thereby indicating fast kinetics and long durability. The excellent performance of Co-Sn nanoparticle alloy-based electrodes was attributed to both the small size of the crystal domains and their suitable composition, which buffered volume changes of Sn and contributed to a suitable electrode restructuration.
RESUMO
The present study outlines the important steps to bring electrochemical conversion of carbon dioxide (CO2) closer to commercial viability by using a large-scale metallic foam electrode as a highly conductive catalyst scaffold. Because of its versatility, it was possible to specifically tailor three-dimensional copper foam through coating with silver dendrite catalysts by electrodeposition. The requirements of high-yield CO2 conversion to carbon monoxide (CO) were met by tuning the deposition parameters toward a homogeneous coverage of the copper foam with nanosized dendrites, which additionally featured crystallographic surface orientations favoring CO production. The presented results evidence that Ag dendrites, owing a high density of planes with stepped (220) surface sites, paired with the superior active surface area of the copper foam can significantly foster the CO productivity. In a continuous flow-cell reactor setup, CO Faradaic efficiencies reaching from 85 to 96% for a wide range of low applied cathode potentials (<1.0 VRHE) along with high CO current densities up to 27 mA/cm2 were achieved, far outperforming other tested scaffold materials. Overall, this research provides new strategic guidelines for the fabrication of efficient and versatile cathodes for CO2 conversion compatible with large-scale integrated prototype devices.
RESUMO
CoxNi1-xTiO3 systems evaluated as photo- and electrocatalytic materials for oxygen evolution reaction (OER) from water have been studied. These materials have shown promising properties for this half-reaction both under (unbiased) visible-light photocatalytic approach in the presence of an electron scavenger and as electrocatalysts in dark conditions in basic media. In both situations, Co0.8Ni0.2TiO3 exhibits the best performance and is proved to display high faradaic efficiency. A synergetic effect between Co and Ni is established, improving the physicochemical properties such as surface area and pore size distribution, besides affecting the donor density and the charge carrier separation. At higher Ni content, the materials exhibit behavior more similar to that of NiTiO3, which is a less suitable material for OER than CoTiO3.
RESUMO
A facile and low-cost method is presented to synthesize graphite/PEDOT/MnO2 composites with controlled network structures on commercial supercapacitor separator (CSS) membranes for high-performance supercapacitors, in which pencil lead and a cellulose-based commercial supercapacitor separator membrane were applied as the graphite source and the flexible substrate, respectively. The dependence of PEDOT and MnO2 loading on the structural formation, the electrochemical performance of the hybrid electrode, and the formation mechanism of MnO2 nanowires are systematically investigated. The optimized electrode possesses a high areal capacitance of 316.4 mF/cm(2) at a scan rate of 10 mV/s and specific capacitance of 195.7 F/g at 0.5 A/g. The asymmetric supercapacitor device assembled using optimized CSS/Graphite/PEDOT/MnO2 electrode and activated carbon electrode exhibits a high energy density of 31.4 Wh/kg at a power density of 90 W/kg and maintains 1 Wh/kg at 4500 W/kg. After 2000 cycles, the device retains 81.1% of initial specific capacitance, and can drive a mini DC-motor for ca. 10 s. The enhanced capability of the CSS-based graphite/PEDOT/MnO2 network electrode has high potential for low-cost, high-performance, and flexible supercapacitors.
RESUMO
A type of freestanding three-dimensional (3D) micro/nanointerconnected structure, with a conjunction of microsized 3D graphene networks, nanosized 3D carbon nanofiber (CNF) forests, and consequently loaded MnO2 nanosheets, has been designed as the electrodes of an ultralight flexible supercapacitor. The resulting 3D graphene/CNFs/MnO2 composite networks exhibit remarkable flexibility and highly mechanical properties due to good and intimate contacts among them, without current collectors and binders. Simultaneously, this designed 3D micro/nanointerconnected structure can provide an uninterrupted double charges freeway network for both electron and electrolyte ion to minimize electron accumulation and ion-diffusing resistance, leading to an excellent electrochemical performance. The ultrahigh specific capacitance of 946 F/g from cyclic voltammetry (CV) (or 920 F/g from galvanostatic charging/discharging (GCD)) were obtained, which is superior to that of the present electrode materials based on 3D graphene/MnO2 hybrid structure (482 F/g). Furthermore, we have also investigated the superior electrochemical performances of an asymmetric supercapacitor device (weight of less than 12 mg/cm(2) and thickness of ~0.8 mm), showing a total capacitance of 0.33 F/cm(2) at a window voltage of 1.8 V and a maximum energy density of 53.4 W h/kg for driving a digital clock for 42 min. These inspiring performances would make our designed supercapacitors become one of the most promising candidates for the future flexible and lightweight energy storage systems.
RESUMO
Three dimensional manganese dioxide/Pt/nickel foam (shortened to MnPtNF) hybrid electrodes were prepared by double-pulse polarization and potentiostatic deposition technologies for supercapacitor applications. The decoration of Pt nanoparticles onto nickel foam varies the nucleation mechanism of the manganese dioxide species, inducing the formation of manganese dioxide nanosheets. Additionally, controlling the size of the Pt nanoparticles leads to modulated nanosheet architecture and electrochemical properties of the manganese dioxide electrode, as revealed by XRD, Raman spectra, SEM, TEM, cyclic voltammetry, galvanostatic charge-discharge and electrochemical impedance spectroscopy. The nanosheet architecture of the MnPtNF electrode favors the transportation of electrons and ions, which results in the enhanced electrochemical properties. Importantly, the optimized MnPtNF electrode obtains a maximum specific capacitance of 1222 F g(-1) at 5 A g(-1) (89% of the theoretical specific capacitance of MnO2) and 600 F g(-1) at 100 A g(-1). Moreover, the presence of Pt nanoparticles in the MnO2 electrode effectively improves its cycling stability, which is confirmed by the increase of the specific capacitance retention from 14.7% to 90% after 600 cycles.