State-of-the-art and challenges in the analysis of renewable gases.

The development of renewable and low-carbon gases for injection into the gas grid obtained by different processes such as anaerobic digestion, pyrogasification, hydrothermal gasification, and methanation, followed by upgrading steps, increases the demand for analysis and characterization in order to fully manage their integration into the gas value chain. If the analysis of the main compounds (methane, carbon dioxide, hydrogen, and carbon monoxide) is well described, the analysis of impurities in renewable gases remains more challenging due to their various natures and quantities. After a brief description of renewable and low-carbon methane production processes, the review focuses on the methods used for the analysis of the different compounds in renewable gases, from the main ones to impurities at ppbv levels. Gas chromatography (GC), coupled with different detectors, is the preferred technique, enabling the analysis and quantification of siloxanes, terpenes, oxygenates, and sulfur compounds. Recently, comprehensive two-dimensional GC has been applied to renewable gases, increasing the number of compounds detected. Non-chromatographic techniques are also reviewed. As sampling is of major importance in the search for reliable analyses, a whole section is devoted to this aspect. Among the available methods, pre-concentration on adsorbent tubes emerges as the most relevant solution.

Gas Digital Microfluidic Platform: Application to Highly Volatile Compound Preconcentration.

Digital microfluidics platforms (DMFPs) have shown their efficiency in sample handling, using elementary operations that may be combined to perform complex applications. In this article, we present a new platform for gaseous samples handling involving a two-step digital preconcentration using the miniaturized preconcentrators of the DMFP. Choosing n-pentane at very low concentrations as a model for highly volatile compounds, poorly retained on the sorbent, the DMFP allowed bypassing the limit set by the breakthrough volume by repeating an elementary operation. It enabled a 5-fold increase of preconcentration factors in comparison to a single preconcentration step and an easier monitoring of the model compound. Promising applications are expected, as this system could be adapted to most volatile compound analysis devices, including micro gas chromatographs, to replace the current single-step preconcentration systems. By switching to two-step preconcentration with a DMFP, i.e., a digital preconcentration, it would be possible to get more concentrated samples through the column for easier trace analysis.

Sampling method development and optimization in view of human hand odor analysis by thermal desorption coupled with gas chromatography and mass spectrometry.

Forensic profiling of human odor is challenging and would be useful to support information provided by dogs in courts of justice. Analyses of volatile compounds constitutive of human odor are commonly performed with gas chromatography coupled with mass spectrometry. All developed methods and sampling prototypes have to be easy to use in the field by crime scene investigators. This paper will focus on techniques for human hand odor sampling prior to analysis by a thermodesorption device coupled with gas chromatography and mass spectrometry. Thermodesorption and gas chromatography methods were developed using a sorbent phase spiked with a mixture of 80 compounds representative of human hand odor. Then, the crucial sampling step was performed indirectly with a homemade device based on air suction and trapping on a sorbent. This indirect sampling device was evaluated with the same synthetic mixture for optimization. An innovative polymer sorbent called Sorb-Star® was compared to classic Tenax TA® packed tubes. Sorb-Star® provided similar recovery to Tenax TA® packed tubes and a smaller pooled coefficient of variation (6 vs 13%). Thus, it appeared to be fully suited to the indirect sampling of human hand odor. The developed methods were successfully applied to real samples, the ultimate aim being the comparison of a suspect's sample to a sample collected from a crime scene.

Validation of a headspace trap gas chromatography and mass spectrometry method for the quantitative analysis of volatile compounds from degraded rapeseed oil.

Due to lipid oxidation, off-flavors, characterized by a fishy odor, are emitted during the heating of rapeseed oil in a fryer and affect the flavor of rapeseed oil even at low concentrations. Thus, there is a need for analytical methods to identify and quantify these products. To study the headspace composition of degraded rapeseed oil, and more specifically the compounds responsible for the fishy odor, a headspace trap gas chromatography with mass spectrometry method was developed and validated. Six volatile compounds formed during the degradation of rapeseed oil were quantified: 1-penten-3-one, (Z)-4-heptenal, hexanal, nonanal, (E,E)-heptadienal, and (E)-2-heptenal. Validation using accuracy profiles allowed us to determine the valid ranges of concentrations for each compound, with acceptance limits of 40% and tolerance limits of 80%. This method was then successfully applied to real samples of degraded oils.

Determination of four acidic nonsteroidal anti-inflammatory drugs in wastewater samples by dispersive liquid-liquid microextraction based on solidification of floating organic droplet and high-performance liquid chromatography.

A simple, environmentally friendly, and sensitive dispersive liquid-liquid microextraction based on solidification of floating organic droplet for the extraction of four acidic nonsteroidal anti-inflammatory drugs (ketoprofen, naproxen, ibuprofen, and diclofenac) from wastewater samples subsequent by high-performance liquid chromatography analysis was developed. The influence of extraction parameters such as pH, the effect of solution ionic strength, type of extraction solvent, disperser solvent, and extraction solvent volume were studied. High enrichment factors (283-302) were obtained through the developed method. The method provides good linearity (r > 0.999) in a concentration range of 1-100 µg/L, good intra- and inter-day precision (relative standard deviation < 7%) and low limits of quantification. The relative recoveries of the selected compounds were situated over 80% both in synthetic and real water samples. The developed method has been successfully applied for the analysis of the selected compounds in wastewater samples.

Oxygen speciation in upgraded fast pyrolysis bio-oils by comprehensive two-dimensional gas chromatography.

Biomass fast pyrolysis is considered as a promising route to produce liquid for the transportation field from a renewable resource. However, the derived bio-oils are mainly oxygenated (45-50%w/w O on a wet basis) and contain almost no hydrocarbons. Therefore, upgrading is necessary to obtain a liquid with lower oxygen content and characterization of oxygenated compounds in these products is essential to assist conversion reactions. For this purpose, comprehensive two-dimensional gas chromatography (GC × GC) can be investigated. Oxygen speciation in such matrices is hampered by the large diversity of oxygenated families and the complexity of the hydrocarbon matrix. Moreover, response factors must be taken into account for oxygenate quantification as the Flame Ionisation Detector (FID) response varies when a molecule contains heteroatoms. To conclude, no distillation cuts were accessible and the analysis had to cover a large range of boiling points (30-630 °C). To take up this analytical challenge, a thorough optimization approach was developed. In fact, four GC × GC column sets were investigated to separate oxygenated compounds from the hydrocarbon matrix. Both model mixtures and the upgraded biomass flash pyrolysis oil were injected using GC × GC-FID to reach a suitable chromatographic separation. The advantages and drawbacks of each column combination for oxygen speciation in upgraded bio-oils are highlighted in this study. Among the four sets, an original polar × semi-polar column combination was selected and enabled the identification by GC × GC-ToF/MS of more than 40 compounds belonging to eight chemical families: ketones, furans, alcohols, phenols, carboxylic acids, guaiacols, anisols, and esters. For quantification purpose, the GC × GC-FID chromatogram was divided into more than 60 blobs corresponding to the previously identified analyte and hydrocarbon zones. A database associating each blob to a molecule and its specific response factor (determined by standards injection at different concentrations) was created. A detailed molecular quantification by GC × GC-FID was therefore accessible after integration of the corrected normalized areas. This paper aims to present a detail level in terms of characterization of oxygenated compounds in upgraded bio-oils which to our knowledge has never been reached so far. It is based on an original column set selection and an extremely accurate quantification procedure.

Characterization of Flavor Compounds in Distilled Spirits: Developing a Versatile Analytical Method Suitable for Micro-Distilleries.

Over the last few years, the development of micro-distilleries producing diverse spirits with various flavors has been observed. Versatile analytical techniques for the characterization of aroma compounds in such alcoholic beverages are therefore required. A model mixture embodying a theoretical distilled spirit was made according to the data found in literature to compare usual extraction techniques. When it was applied to the model liquor, the headspace solid phase microextraction (HS-SPME) extraction method was preferred to the liquid-liquid extraction (LLE), solid phase extraction (SPE) and stir bar/headspace sorptive extraction (SBSE/HSSE) methods according to efficiency, cost, and environmental criteria. An optimization study using the model mixture showed that the extraction was optimal with a divinylbenzene/carboxen/poly(dimethylsiloxane) DVB/CAR/PDMS fiber, during 60 min, at 35 °C and with the addition of 10% NaCl. This method was successfully applied to three different commercial liquors and led to the identification of 188 flavor compounds, including alcohols, esters, lactones, carbonyls, acetals, fatty acids, phenols, furans, aromatics, terpenoids, alkenes, and alkanes.

Considerations on orthogonality duality in comprehensive two-dimensional gas chromatography.

The term "orthogonal" in comprehensive two-dimensional gas chromatography (GC × GC) has a double sided meaning as it stands for a separation resulting from the combination of two independent retention mechanisms (Giddings, J. C. J. High Resolut. Chromatogr. 1987, 10, 319) but also for a 2D separation where the components are evenly distributed over the entire 2D space. It is shown in the present study that a nonorthogonal GC × GC system associating a polar stationary phase in the first dimension (poly(ethylene glycol)) to a nonpolar one in the second dimension (poly(dimethyl siloxane)) leads to a structured chromatogram, a high peak capacity, and a great 2D space occupation. This idea is demonstrated through the characterization of oxygenated compounds in a coal-derived middle distillate. Results show a clear separation between oxygenated species and hydrocarbons which are classified into linear alkanes, cyclic alkanes, and aromatics. A breakthrough configuration combining a polar poly(ethylene glycol) first dimension and a trifluoropropyl methyl stationary phase in the second dimension enabled a unique identification and quantification of linear, cyclic, and aromatic alcohols. This configuration which could be considered as nonorthogonal still involves two different retention mechanisms: polarity and boiling point in the first dimension and electronic interactions in the second dimension. It is selective toward electronegative poles of alcohols and phenols. The contributions of these two configurations compared to a conventional orthogonal system as well as their roles for oxygenated compounds speciation are highlighted. This contribution is measured through three 2D space occupation factors. It appears through these two examples that orthogonality is intimately linked to analyte properties, and a general concept of dimensionality must be considered.

Feasibility of ultra high performance supercritical neat carbon dioxide chromatography at conventional pressures.

The implementation of columns packed with sub-2 µm particles in supercritical fluid chromatography (SFC) is described using neat carbon dioxide as the mobile phase. A conventional supercritical fluid chromatograph was slightly modified to reduce extra column band broadening. Performances of a column packed with 1.8 µm C18-bonded silica particles in SFC using neat carbon dioxide as the mobile phase were compared with results obtained in ultra high performance liquid chromatography (UHPLC) using a dedicated chromatograph. As expected and usual in SFC, higher linear velocities than in UHPLC must be applied in order to reach optimal efficiency owing to higher diffusion coefficient of solutes in the mobile phase; similar numbers of theoretical plates were obtained with both techniques. Very fast separations of hydrocarbons are presented using two different alkyl-bonded silica columns.

Extended characterization of a vacuum gas oil by offline LC-high-temperature comprehensive two-dimensional gas chromatography.

In a context of environmental preservation, purification and conversion of heavy petroleum cuts into high-quality fuel becomes essential. The interest for the characterization of those very complex matrices becomes a trendy analytical challenge, when it comes to get molecular information for the optimization of industrial processes. Among new analytical techniques, high-temperature 2-D GC has recently proved its applicability to heavy petroleum matrices, but lacks in selectivity to separate all chemical groups. To gain resolution, heart cutting is demonstrated for LC separation of saturated, aromatic and polar compounds prior to high-temperature 2-D GC. Therefore, an extended global resolution was obtained, especially by a better distinction of saturated compounds. This includes iso-paraffins and biomarker polynaphthenic structures, which are impossible to quantify with MS methods. This new way to analyze heavy petroleum fractions gives innovative opportunities for the construction of global weight distributions by carbon atoms number and by chemical families. This can right now be employed for quantitative analysis of heavy petroleum fractions and for studying conversion processes.

Corona charged aerosol detector non-uniform response factors of purified alcohol ethoxylated homologues using liquid chromatography.

Surfactants are used in various applications: cosmetics, pharmaceuticals, petrochemicals, environmental, etc. Many of these compounds are polydisperse, and because of this intrinsic polydispersity, it is essential to have a universal detector with a uniform response to quantify them in a simple way. Indeed, Charged Aerosol Detector (CAD) was presented as a universal detector with a uniform response. Thus, in the present study, the CAD response, in a High-Performance Liquid Chromatography - CAD configuration (HPLCCAD), was evaluated using purified alcohol ethoxylated surfactants. A semi-preparative liquid chromatography step using a Hydrophilic interaction chromatography (HILIC) bare silica column (150 mm, 4.6 mm, 2.6 µm) was implemented to prepare eleven homologues of BrijC10, a nonionic surfactant. These homologues differed only by the number of ethylene oxide units. BrijC10 homologues were analyzed by HPLCCAD, using a HILIC bare silica column (150 mm, 2.1 mm, 2.6 µm) to determine the HPLCCAD response factors of purified homologues. From the calibration curves (from 100 to 500 mg.kg-1), their response factors were estimated: differences in response factors were observed and a maximum difference in response factors of 3.6 was obtained. Thus, it could be concluded that CAD hyphenated to HILIC separation did not present a uniform response for this homologue's distribution.

Chromatographic behavior and characterization of polydisperse surfactants using Ultra-High-Performance Liquid Chromatography hyphenated to High-Resolution Mass Spectrometry.

Surfactants are widely used in various petrochemical applications. Thus, it is essential to have highly efficient analytical tools to monitor the different classes of surfactants commonly used. Three among the four known classes of surfactants were studied in the present work: anionic (i.e. alkylbenzene sulfonate, alkyl ether carboxylic acid), nonionic (i.e. alkylcyclohexyl alcohol ethoxylated, alkyl alcohol ethoxylated) and cationic (i.e. alkyl trimethylammonium). Thanks to high-resolution mass spectrometry (HRMS), a useful mass list was created including 119 m/z values (error in mass around 5 ppm). This list was the foundation of a HRMS database, which, for the sake of simplicity, will be further denoted only "database". To avoid ion competition and streamline attribution of structural formulas for isobar molecules, a suitable chromatographic method was used before MS. The retention behavior of six surfactants (trimethyloctadecylammonium bromide, myristyltrimethylammonium bromide, Brij®C10, Triton X-100 reduced, glycolic acid ethoxylate lauryl ether, 4-dodecylbenzenesulfonic acid) was evaluated under three separation modes: reversed-phase liquid chromatography (RPLC), hydrophilic interaction chromatography (HILIC) and mixed-mode chromatography (combination of anion-exchange and reversed-phase mechanisms). In RPLC mode, six columns were tested including C4, C18, C30, polar-embedded C18, PFP and phenyl chemistries. Two HILIC columns were also tested including bare silica and urea chemistries. An anion-exchange combined with RPLC mechanism was investigated as mixed-mode mechanism. Using ammonium formate at 10 mM as buffer provided the best signal in HRMS. In liquid chromatography, acid conditions (pH 3.5) were preferred, to avoid peak tailing due to residual silanols. The mixed-mode separation mode clearly appears as the best compromise for the characterization of the three surfactants classes. Nevertheless, the orthogonality observed for the separations obtained in HILIC and RPLC modes offers some possibilities for further multidimensional separations.

A promising "metastable" liquid crystal stationary phase for gas chromatography.

The liquid crystal state is an ordered physical state between a solid and a liquid. Previous research, in gas chromatography, proved that it provides a geometric selectivity, which allows the separation of geometric position isomers and cis-trans isomers that are difficult to separate on conventional gas chromatography stationary phases (polydimethyl siloxane derived and polyethylene glycol stationary phases). However, their use was generally very limited by the rather high temperature at which they must be operated, normally above the solid-liquid crystal transition temperature. In the present study we are interested in a new synthesized material, 1,4- bis (4-bromohexyloxy benzoate) phenyl (BHOBP). The first characterizations of BHOBP were carried out by thermogravimetric analysis, hot-stage optical microscopy and differential scanning calorimetry to control the thermal stability of the BHOBP as well as the nematic texture of the mesophase highlighted in a well-defined temperature range (120 °C-200 °C). When heated, the solid compound led to a stable liquid crystal state. Its cooling has revealed "a new metastable physical state, which is the supercooled liquid crystal phase". After these first characterizations, the new material was used as a stationary phase for gas chromatography. The BHOBP was deposited in a capillary column by the dynamic method. The inverse gas chromatography study of the column revealed a solid-stable nematic phase transition temperature, in agreement with the first characterization methods. The stable liquid crystal phase showed good resolutions in the analysis of some geometric isomers of low volatility as PAHs. The presence of the supercooled liquid crystal state in the chromatographic column has also been confirmed. This new metastable state is particularly interesting because it enlarged the scope of this material by improving the resolution of several mixtures. Thus, the separation of highly volatile mixtures of geometric isomers (e.g. cis and trans-decalin) was achieved only through this metastable mesophase confirming its unique selectivity. The metastable liquid crystal, used at 80 °C, has also exhibited an original behavior by its stability after several weeks of use at the same temperature, maintaining constant retention factors and selectivity.

Analysis of multiclass organic pollutant in municipal landfill leachate by dispersive liquid-liquid microextraction and comprehensive two-dimensional gas chromatography coupled with mass spectrometry.

We propose a simple, fast, and inexpensive method for the analyses of 72 organic compounds in municipal landfill leachate, based on dispersive liquid-liquid microextraction and comprehensive two-dimensional gas chromatography coupled with mass spectrometry. Forty-one organic compounds belonging to several classes including hydrocarbons, mono- and polyaromatic hydrocarbons, carbonyl compounds, terpenes, terpenoids, phenols, amines, and phthalates, covering a wide range of physicochemical properties and linked to municipal landfill leachate, were quantitatively determined. Another 31 organic compounds such as indoles, pyrroles, glycols, organophosphate flame retardants, aromatic amines and amides, pharmaceuticals, and bisphenol A have been identified based on their mass spectra. The developed method provides good performances in terms of extraction recovery (63.8-127%), intra-day and inter-day precisions (< 7.7 and < 13.9 respectively), linearity (R2 between 0.9669 and 0.9999), detection limit (1.01-69.30 µg L-1), quantification limit (1.87-138.6 µg L-1), and enrichment factor (69.6-138.5). Detailed information on the organic pollutants contained in municipal landfill leachate could be obtained with this method during a 40-min analysis of a 4-mL leachate sample, using only 75 µL of extraction solvent.

Hyphenation of atmospheric pressure chemical ionisation mass spectrometry to supercritical fluid chromatography for polar car lubricant additives analysis.

Car lubricant additives are added to mineral or synthetic base stocks to improve viscosity and resistance to oxidation of the lubricant and to limit wear of engines. As they belong to various chemical classes and are added to a very complex medium, the base stock, their detailed chromatographic analysis is very difficult and time consuming. In a previous paper, it was demonstrated that supercritical fluid chromatography (SFC) allows the elution of common low-molecular-weight additives. Since their total resolution could not be achieved owing to the limited peak capacity of packed columns, the hyphenation of selective and informative detection methods such as atomic emission detection (AED) was required. Further to results obtained in SFC-AED, this work describes the hyphenation of SFC to atmospheric pressure chemical ionisation ion trap mass spectrometry (MS). SFC-MS hyphenation is detailed: temperature, flow rates of gas and mobile phase introduced in the source, position of the restrictor, ionisation additives and conditions of autotune are studied. Car lubricant monitoring requires negative and positive ionisation modes with or without the addition of ionisation auxiliary solvent according to the nature of additives. Moreover, when sensitivity is of major concern for a selected additive, the autotuning routine of the MS has to be performed in conditions as close as possible to analytical conditions, i.e. under subcritical conditions. Unambiguous identification and structure elucidation of several additives in formulated car lubricants are also presented.

Molecularly imprinted polymer for solid-phase extraction of ephedrine and analogs from human plasma.

A molecularly imprinted polymer (MIP) was synthesized and evaluated to selectively extract ephedrine from human plasma. The MIP synthesis was performed in chloroform with methacrylic acid as a functional monomer and the target alkaloid as a template molecule. The resulting MIP was applied to the selective extraction of ephedrine from a pure aqueous medium. A recovery about 74% was obtained using the MIP with only 7% on the nonimprinted polymer (NIP). A very straightforward selective SPE procedure was then successfully applied to the direct extraction of ephedrine from spiked human plasma with a high extraction recovery (68%) on the MIP with no recovery on the NIP. Moreover, the MIP was used for the selective extraction of catecholamine neurotransmitters, i.e. adrenaline and noradrenaline.

Comprehensive two-dimensional gas chromatography for enhanced analysis of naphthas: new column combination involving permethylated cyclodextrin in the second dimension.

A new column association using comprehensive two-dimensional gas chromatography for the detailed molecular analysis of hydrocarbon mixtures is reported in this paper. In order to compare the impact of two different secondary columns, a novel column combination relying on a GC x 2GC system was used. This system is based on a non-polar first column (PONA) combined with both a permethylated beta-cyclodextrin (beta-Dex 120) stationary phase and a polysilphenylensiloxane (BPX 50) in the second dimension. Compared to BPX 50 stationary phase, the implementation of beta-cyclodextrin columns as the second dimension was found to improve the resolution between paraffins and naphthenes in the naphtha range but not in the middle distillate range. Attempts to improve the results and to understand the interaction mechanism remained unsuccessful. Therefore, the benefits of the beta-Dex 120-column are only demonstrated on heavy naphtha cut for the quantitation of hydrocarbons.

Using comprehensive two-dimensional gas chromatography for the analysis of oxygenates in middle distillates I. Determination of the nature of biodiesels blend in diesel fuel.

In the current energetic context (increasing consumption of vehicle fuels, greenhouse gas emission etc.) government policies lead to mandatory introduction in fossil fuels of fuels resulting from renewable sources of energy such as biomass. Blending of fatty acid alkyl esters from vegetable oils (also known as biodiesel) with conventional diesel fuel is one of the solutions technologically available; B5 blends (up to 5%w/w esters in fossil fuel) are marketed over Europe. Therefore, for quality control as well as for forensic reasons, it is of major importance to monitor the biodiesel origin (i.e. the fatty acid ester distribution) and its content when it is blend with petroleum diesel. This paper reports a comprehensive two-dimensional gas chromatography (GC x GC) method that was developed for the individual quantitation of fatty acid esters in middle distillates matrices. Several first and the second dimension columns have been investigated and their performances to achieve (i) a group type separation of hydrocarbons and (ii) individual identification and quantitation of fatty acid ester blend with diesel are reported and discussed. Finally, comparison of quantitative GC x GC results with reference methods demonstrates the benefits of GC x GC approach which enables fast and reliable individual quantitation of fatty acid esters in one single run. Results show that under developed chromatographic conditions, quantitative group type analysis of hydrocarbons is also possible, meaning that simultaneous quantification of hydrocarbons and fatty acid esters can be achieved in one single run.

Active modulation in neat carbon dioxide packed column comprehensive two-dimensional supercritical fluid chromatography.

After demonstrating in a first paper the feasibility of SFCxSFC without decompression of the mobile phase, a modified interface has been developed in order to perform active modulation between the two SFC dimensions. In this paper, it is shown that the new interface enabled independent control of modulation parameters in SFCxSFC and performed a band compression effect of solutes between the two SFC dimensions. The effectiveness of this new modulation process was studied using a Design of Experiments. The SFCxSFC prototype was applied to the analysis of a real oil sample to demonstrate the benefits of the active modulator; in comparison to our previous results obtained without active modulation, better separation was obtained with the new interface owing to the peak compression occurring in the modulator.

Human odor and forensics. Optimization of a comprehensive two-dimensional gas chromatography method based on orthogonality: How not to choose between criteria.

The use of comprehensive two-dimensional gas chromatography coupled with mass spectrometry would be a real asset for the forensic profiling of human hand odor. This paper focuses on the optimization of a comprehensive gas chromatography method using a synthetic mixture of 80 compounds representative of human hand odor composition. In order to rank the candidate column sets, instead of using a unique criterion, we used a chemometric tool called desirability which is based on Derringer functions and enables to consider several criteria simultaneously and hence to get the best compromise. Nine criteria including six orthogonality criteria were used to evaluate the quality and the efficiency of the separation. The desirability analysis lead to a straightforward ranking and an accurate overview of the results in two situations, with an objective of routine analysis and without. In both cases, the DB-1MS×DB-1701 set was found to be best suited for the separation of the considered mixture, however with different gradients.