Effects of Cusp Inclination and Light-curing Time on Microshear Bond Strength of a Dual-cure, Self-adhesive Composite Cement to Zirconia.

PURPOSE: To evaluate the effect of cusp inclination and light-curing time on the microshear bond strength (µSBS) between zirconia and a dual-cure self-adhesive composite cement and zirconia. MATERIALS AND METHODS: Forty U-shaped specimens with angled surfaces, simulating different cusp inclinations (0 degrees, 20 degrees, and 30 degrees), were fabricated from zirconia blocks (Zenostar, Wieland). The specimens were randomly divided into two groups (n = 20) according to different light-curing times of the adhesive composite cements (20 s and 40 s). Three polyethylene tubes filled with a dual-curing self-adhesive composite cement (Multilink Speed, Ivoclar Vivadent) were bonded to the surfaces of each specimen with light-curing times of 20 s and 40 s. The µSBS was tested using a universal testing machine with a crosshead speed of 0.5 mm/min. Failure analysis was performed. Two-way ANOVA (cusp inclination and light-curing time) followed by two independent samples t-test were used for statistical analyses (α = 0.05). RESULTS: The composite cement showed various bond strengths to angled zirconia surfaces (7.07 ± 1.69 to 13.91 ± 3.11 MPa). The µSBS between composite cement and 0-degree zirconia surfaces was statistically higher than that of 20- and 30-degree zirconia surfaces. The composite cement light cured for 40 s showed nonsignificantly higher µSBS than did the composite cement cured for 20 s. Adhesive failure was the most common failure mode. CONCLUSIONS: Cusp inclination affected bond strength between the dual-curing self-adhesive composite cement and zirconia.

Bonding to zirconia: Effects of translucency and cusp inclinations using an experimental methodology.

Purpose To investigate the effects of translucency and cusp inclination on the micro-shear bond strength (µSBS) of zirconia to self-adhesive resin cement (SARC).Methods Sixty U-shaped zirconia specimens with 1.0 mm thickness consisting of three planes (0°, 20°, and 30°) simulating different cusp inclinations were fabricated from zirconia blocks of high, moderate, and low translucency (n=20). SARC was bonded to the specimen and light-cured for 40 s. The µSBS was tested using a universal testing machine with a cross-head at a speed of 0.5 mm/min and fracture mode was observed using a stereomicroscope (×50). Two-way analysis of variance followed by a post hoc Tukey's honest significant difference test was used for the statistical analyses (α=0.05).Results Varied µSBS values were found in the test groups (7.1-14.9 MPa). Within the zirconia of the same translucency, the µSBS value of the plane 0° specimen was significantly higher than that of the 20° and 30° planes (all p<0.05). Within the zirconia of the same cusp inclination, the µSBS value of highly translucent zirconia was significantly higher than that of moderate and low translucent zirconia (all p<0.05). There was no significant interaction between cusp inclination and translucency (p=0.525). Among the fracture modes, 83.33% were adhesive failure, 11.11% mixed failure, and 5.56% were cohesive failure.Conclusions Translucency and cusp inclination significantly affect the µSBS of zirconia to SARC. The higher the translucency, the greater are the µSBS values; the higher the cusp inclination, the lower are the µSBS values.

In Vitro Cytotoxicity of Self-Adhesive Dual-Cured Resin Cement Polymerized Beneath Three Different Cusp Inclinations of Zirconia.

The aim of the present study was to evaluate the in vitro cytotoxicity of self-adhesive dual-cured resin cement (SADRC) polymerized beneath three different cusp inclinations of zirconia with different light curing time. A commercial SADRC (Multilink Speed) was polymerized beneath zirconia (ZrO2) with three different cusp inclinations (0°, 20°, and 30°) for 20 s or 40 s. After being stored in light-proof box for 24 h, the ZrO2-SADRC specimens were immersed in DMEM for 72 h and then we got the extract solution, cultured the human gingival fibroblasts (HGF, 8 × 103 per well) with 100% or 50% concentrations of the extract solution for 24 h, 72 h, and 120 h, respectively, and evaluated cytotoxicity of the polymerized SADRC with CCK-8 assay in optical density (OD) values, relative growth rates (RGR), and cytotoxicity grades. Statistical analysis was conducted using a two-way ANOVA followed by post hoc Student-Newman-Keuls test. The OD values varied from 0.8930 to 3.2920, the RGR varied from 33.93% to 98.68%, and the cytotoxicity grades varied from 0 to 2. There was significant difference in the OD values among the different cusp inclinations of zirconia (P < 0.001), and there was significant difference in the OD values between the different light curing times in some situations (P < 0.05). The cusp inclination of zirconia affects the in vitro cytotoxicity of SADRC. Prolonging the light curing time from 20 s to 40 s can reduce the in vitro cytotoxicity of SADRC when the cusp inclination of zirconia is smaller than 20°.