RESUMO
The low-temperature modification of ß-Ag2Se has proven to be useful as a near-room-temperature thermoelectric material. Over the past years, research has been devoted to interstitial, vacancy, and substitutional doping into the parent ß-Ag2Se structure, aiming at tuning the material's charge and heat transport properties to enhance thermoelectric performance. The transformation of ß-Ag2Se into α-Ag2Se at â¼134 °C and the low solubility of dopants are the main obstacles for the doping approach. Herein, we report a facile, safe, scalable, and cost-effective benchtop approach to successfully produce metal-doped ß-Ag2Se. The doped materials display a remarkable enhancement of thermoelectric performance with a record-high peak zT of 1.30 at 120 °C and an average zT of â¼1.15 in the 25-120 °C range for 0.2 at. % Zn-doped Ag2Se. The enhancement in zT is attributed to point defects created by Zn doping into Ag vacancies/interstitials, which enhances the scattering of phonons and tunes the charge carrier properties, leading to the significant suppression of thermal conductivity. The simplicity of the synthetic method developed herein and the high performance of the final products provide an avenue to produce high-quality Ag2Se-based thermoelectric materials.
RESUMO
[Fe(en)(tren)][FeSe2]2 (en = ethylenediamine, C2H8N2, tren = tris(2-aminoethyl)amine, C6H18N4) has been synthesized by a mixed-ligand solvothermal method. Its crystal structure contains heteroleptic [Fe(en)(tren)]2+ complexes with distorted octahedral coordination, incorporated between 1D-FeSe2 chains composed of edge-sharing FeSe4 tetrahedra. The twisted octahedral coordination environment of the Fe-amine complex leads to partial dimerization of Fe-Fe distances in the FeSe2 chains so that the FeSe4 polyhedra deviate strongly from the regular tetrahedral geometry. 57Fe Mössbauer spectroscopy reveals oxidation states of +3 for the Fechain atoms and +2 for the Fecomplex atoms. The close proximity of Fe atoms in the chains promotes ferromagnetic nearest neighbor interactions, as indicated by a positive Weiss constant, θ = +53.8(6) K, derived from the Curie-Weiss fitting. Magnetometry and heat capacity reveal two consecutive magnetic transitions below 10 K. DFT calculations suggest that the ordering observed at 4 K is due to antiferromagnetic intrachain interactions in the 1D-FeSe2 chains. The combination of two different ligands creates an asymmetric coordination environment that induces changes in the structure of the Fe-Se fragments. This synthetic strategy opens new ways to explore the effects of ligand field strength on the structure of both Fe-amine complexes and surrounding Fe-Se chains.
RESUMO
The zinc-antimony phase space has been heavily investigated due to the structural complexity and abundance of high-performing thermoelectric materials. Consequentially, the desire to use zinc and antimony as framework elements to encage rattling cations and achieve phonon-glass-electron-crystal-type properties has remained an enticing goal with only two alkali metal clathrates to date, Cs8Zn18Sb28 and K58Zn122Sb207. Guided by Zintl electron-counting predictions, we explored the Ba-Zn-Pn (Pn = As, Sb) phase space proximal to the expected composition of the type-I clathrate. In situ powder X-ray diffraction studies revealed two "hidden" compounds which can only be synthesized in a narrow temperature range. The ex situ synthesis and crystal growth unveiled that instead of type-I clathrates, compositionally close but structurally different new clathrate-like compounds formed, Ba2Zn5As6 and Ba2Zn5Sb6. These materials crystallize in a unique structure, in the orthorhombic space group Pmna with the Wyckoff sequence i2h6gfe. Single-phase synthesis enabled the exploration of their transport properties. Rattling of the Ba cations in oversized cages manifested low thermal conductivity, which, coupled with the high Seebeck coefficients observed, are prerequisites for a promising thermoelectric material. Potential for further optimization of the thermoelectric performance by aliovalent doping was computationally analyzed.
RESUMO
The inertness of elemental selenium is a significant obstacle in the synthesis of selenium-containing materials at low reaction temperatures. Over the years, several recipes have been developed to overcome this hurdle; however, most of the methods are associated with the use of highly toxic, expensive, and environmentally harmful reagents. As such, there is an increasing demand for the design of cheap, stable, and nontoxic reactive selenium precursors usable in the low-temperature synthesis of transition metal selenides with vast applications in nanotechnology, thermoelectrics, and superconductors. Herein, a novel synthetic route has been developed for activating elemental selenium by using a solvothermal approach. By comprehensive 77Se NMR, Raman, and infrared spectroscopies and gas chromatography-mass spectrometry, we show that the activated Se solution contained HSe-, [Se-Se]2-, and Se2- ions, as well as dialkyl selenide (R2Se) and dialkyl diselenide (R-Se-Se-R) species in dynamic equilibrium. This also corresponded to the first observation of naked Se22- in solution. The versatility of the developed Se precursor was demonstrated by the successful synthesis of (i) the polycrystalline room-temperature modification of the ß-Ag2Se thermoelectric material; (ii) large single crystals of superconducting ß-FeSe; (iii) CdSe nanocrystals with different particle sizes (3-10 nm); (iv) nanosheets of PtSe2; and (v) mono- and dibenzyl selenides and diselenides at room temperature. The simplicity and diversity of the developed Se activation method holds promise for applied and fundamental research.
RESUMO
A series of Yb-substituted Zintl phases in the Ca3-xYbxAlSb3 (0 ≤ x ≤ 0.81(1)) system has been synthesized by initial arc melting and post-heat treatment, and their isotypic crystal structures were characterized by both powder and single crystal X-ray diffraction analysis. All four title compounds adopted the Ca3AlAs3-type structure (space group Pnma, Pearson code oP28, Z = 4). The overall structure can be described as a combination of the 1-dimensional (1D) infinite chain of ∞1[Al(Sb2Sb2/2)] formed by two vertices sharing [AlSb4] tetrahedral moieties and three Ca2+/Yb2+ mixed sites located in between these 1D chains. The charge balance and the resultant independency of the 1D chains in the title system were explained by the Zintl-Klemm formalism [Ca2+/Yb2+]3[(4b-Al1-)(1b-Sb2-)2(2b-Sb1-)2/2]. A series of DFT calculations proved that (1) the band overlap between the d-orbital states from two types of cations and the p-orbital states from Sb at the high symmetry Γ point implied a heavily doped degenerate semiconducting behavior of the quaternary Ca2YbAlSb3 model and (2) the site preference of Yb for the M1 site was due to the electronic-factor criterion based on the Q values of each atomic site. The electron localization function calculations also proved that the two different shapes of lone pairs of the Sb atomsâthe "umbrella-shape" and the "C-shape"âare determined by local geometry and the coordination environment on the anionic frameworks. Thermoelectric measurements of the quaternary title compound Ca2.19(1)Yb0.81AlSb3 showed an approximately two times larger ZT value than that of ternary Ca3AlSb3 at 623 K due to increased electrical conductivity and ultralow thermal conductivity originated from Yb substitution for Ca.
RESUMO
A novel mixed-valent hybrid chiral and polar compound, Fe7As3Se12(en)6(H2O), has been synthesized by a single-step solvothermal method. The crystal structure consists of 1D [Fe5Se9] chains connected via [As3Se2]-Se pentagonal linkers and charge-balancing interstitial [Fe(en)3]2+ complexes (en = ethylenediamine). Neutron powder diffraction verified that interstitial water molecules participate in the crystal packing. Magnetic polarizability of the produced compound was confirmed by X-ray magnetic circular dichroism (XMCD) spectroscopy. X-ray absorption spectroscopy (XAS) and 57Fe Mössbauer spectroscopy showed the presence of mixed-valent Fe2+/Fe3+ in the Fe-Se chains. Magnetic susceptibility measurements reveal strong antiferromagnetic nearest neighbor interactions within the chains with no apparent magnetic ordering down to 2 K. Hidden short-range magnetic ordering below 70 K was found by 57Fe Mössbauer spectroscopy, showing that a fraction of the Fe3+/Fe2+ in the chains are magnetically ordered. Nevertheless, complete magnetic ordering is not achieved even at 6 K. Analysis of XAS spectra demonstrates that the fraction of Fe3+ in the chain increases with decreasing temperature. Computational analysis points out several competing ferrimagnetic ordered models within a single chain. This competition, together with variation in the Fe oxidation state and additional weak intrachain interactions, is hypothesized to prevent long-range magnetic ordering.
RESUMO
A series of solid solutions, CuFe2-xCoxGe2 (x = 0, 0.2, 0.4, 0.8, and 1.0), have been synthesized by arc-melting and characterized by powder X-ray and neutron diffraction, magnetic measurements, Mössbauer spectroscopy, and electronic band structure calculations. All compounds crystallize in the CuFe2Ge2 structure type, which can be considered as a three-dimensional framework built of fused MGe6 octahedra and MGe5 trigonal bipyramids (M = Fe and Co), with channels filled by rows of Cu atoms. As the Co content (x) increases, the unit cell volume decreases in an anisotropic fashion: the b and c lattice parameters decrease while the a parameter increases. The changes in all the parameters are nearly linear, thus following Vegard's law. CuFe2Ge2 exhibits two successive antiferromagnetic (AFM) orderings, corresponding to the formation of a commensurate AFM structure, followed by an incommensurate AFM structure observed at lower temperatures. As the Co content increases, the AFM ordering temperature (TN) gradually decreases, and only one AFM transition is observed for x ≥ 0.2. The magnetic behavior of unsubstituted CuFe2Ge2 was found to be sensitive to the preparation method. The temperature-dependent zero-field 57Fe Mössbauer spectra reveal two hyperfine split components that evolve in agreement with the two consecutive AFM orderings observed in magnetic measurements. In contrast, the field-dependent spectra obtained for fields ≥2 T reveal a parallel arrangement of the moments associated with the two crystallographically unique metal sites. Electronic band structure calculations and chemical bonding analysis reveal a mix of strong M-M antibonding and non-bonding states at the Fermi level, in support of the overall AFM ordering observed in zero field. The substitution of Co for Fe reduces the population of the M-M antibonding states and the overall density of states at the Fermi level, thus suppressing the TN value.
RESUMO
Two novel layered compounds BaCuSi2Pn3 (Pn = P, As) adopting new structure types are reported. As revealed by single-crystal X-ray diffraction, both compounds are composed of unique Cu-Si-Pn layers featuring CuPn3 and Si2Pn6 structural motifs found in other archetypal pnictide materials. The stacking of the isostructural Cu-Si-Pn layers is different for phosphide and arsenide compounds. Synthesis from elements aided by in situ synchrotron powder X-ray diffraction resulted in the obtainment of bulk powders with a minimized amount of admixtures. Experimentally measured physical properties of BaCuSi2As3 unexpectedly showed metal-like behavior at temperatures above 15 K, despite the fact that density functional theory calculations predict a small band gap of 0.4 eV. BaCuSi2As3 exhibits ultralow thermal conductivity, which can be explained by the combination of a layered crystal structure with alternating covalent and ionic bonding, which feature rattling of Cu atoms similar to that in tetrahedrites.
RESUMO
The alkaline-earth-containing nickel phosphide clathrates AeNi2P4 (Ae = Ba, Sr) are investigated as catalysts for the reduction of nitrate or nitroarenes in aqueous or ethanolic solution, respectively. While AeNi2P4 clathrates are inactive in their bulk polycrystalline form, they become active in nitrate hydrogenation after size reduction by either grinding or ball milling. However, while the clathrate structure remains intact after manual grinding, ball milling is of limited use as it results in significant clathrate degradation. Ground AeNi2P4 catalysts are also active in nitroarene hydrogenation. Condensation products such as azoxy- and azo-benzenes form early (4 h) but anilines accumulate after long reaction times (24 h). Unexpectedly, BaNi2P4 partially devinylates nitrostyrene to nitrobenzene. Overall, BaNi2P4 is more active than SrNi2P4 in both nitrate and nitroarene hydrogenation. These results showcase the potential utility of clathrates in a growing number of catalytic transformations.
RESUMO
The solvothermal synthetic exploration of the Bi-S-halogen phase space resulted in the synthesis of two bismuth sulfohalides with common structural motifs. Bi13S18I2 was confirmed to have the previously reported composition and crystal structure. In contrast, the bromide analogue was shown to have a formula of neither Bi19S27Br3 nor Bi13S18Br2, in contrast to the previous reports. The composition, refined from single crystal X-ray diffraction and confirmed by elemental analysis, high-resolution powder X-ray diffraction, and total scattering, is close to Bi13S17Br3 due to the partial S/Br substitution in the framework. Bi13S18I2 and Bi13S17Br3 are n-type semiconductors with similar optical bandgaps of â¼0.9 eV but different charge and heat transport properties. Due to the framework S/Br disorder, Bi13S17Br3 exhibits lower thermal and electrical conductivities than the iodine-containing analogue. The high Seebeck coefficients and ultralow thermal conductivities indicate that the reported bismuth sulfohalides are promising platforms to develop novel thermoelectric materials.
RESUMO
A series of novel semiconductors AAe6Si12P20X (A = Na, K, Rb, Cs; Ae = Sr, Ba; X = Cl, Br, I) is reported. Their crystal structures feature a tetrahedral Si-P framework with large zeolite-like pores hosting two types of cations, monoatomic A+ and unprecedented octahedral X@Ae611+. Mixing of the A and Ba cations was detected by single crystal X-ray diffraction and confirmed by multinuclear solid state NMR. The reported compounds are highly stable semiconductors with a bandgap range from 1.4 to 2.0 eV.
RESUMO
The first arsenic-based clathrate exhibiting superstructural ordering due to optimization of Au-As, As-As, and Ba-Au bonding is reported. Ba8Au16As30 crystallizes in a unique P21/c monoclinic clathrate structure. The synthesis, crystal and electronic structure, and transport properties are discussed.
RESUMO
Complex pnictides such as I-II4-V3 compounds (I = alkali metal; II = divalent transition metal; V = pnictide element) display rich structural chemistry and interesting optoelectronic properties, but can be challenging to synthesize using traditional high-temperature solid-state synthesis. Soft chemistry methods can offer control over particle size, morphology, and properties. However, the synthesis of multinary pnictides from solution remains underdeveloped. Here, we report the colloidal hot-injection synthesis of ACd4P3 (A = Na, K) nanostructures from their alkali metal hydrides (AH). Control studies indicate that NaCd4P3 forms from monometallic Cd0 seeds and not from binary Cd3P2 nanocrystals. IR and ssNMR spectroscopy reveal tri-n-octylphosphine oxide (TOPO) and related ligands are coordinated to the ternary surface. Computational studies show that competing phases with space group symmetries R3Ì m and Cm differ by only 30 meV/formula unit, indicating that synthetic access to either of these polymorphs is possible. Our synthesis unlocks a new family of nanoscale multinary pnictide materials that could find use in optoelectronic and energy conversion devices.
RESUMO
An innovative method of synthesis is reported for the large and diverse (RE)6(TM) x (Tt)2S14 (RE = rare-earth, TM = transition metals, Tt = Si, Ge, and Sn) family of compounds (â¼1000 members, â¼325 contain Si), crystallizing in the noncentrosymmetric, chiral, and polar P63 space group. Traditional synthesis of such phases involves the annealing of elements or binary sulfides at elevated temperatures. The atomic mixing of refractory components technique, presented here, allows the synthesis of known members and vastly expands the family to nearly the entire transition metal block, including 3d, 4d, and 5d TMs with oxidation states ranging from 1+ to 4+. Arc-melting of the RE, TM, and tetrel elements of choice forms an atomically-mixed precursor, which readily reacts with sulfur providing bulk powders and large single crystals of the target quaternary sulfides. Detailed in situ and ex situ experiments show the mechanism of formation, which involves multiphase binary sulfide intermediates. Crystal structures and metal oxidation states were corroborated by a combination of single crystal X-ray diffraction, elemental analysis, EPR, NMR, and SQUID magnetometry. The potential of La6(TM) x (Tt)2S14 compounds for non-linear optical applications was also demonstrated.
RESUMO
Flux crystal growth has been widely applied to explore new phases and grow crystals of emerging materials. To accommodate the needs of high-quality single crystals, the flux crystal growth should be reliable, controllable, and predictable. The selections of suitable flux and growth conditions remain empirical due to the lack of systematic investigation especially for reactions, which involve highly volatile components, such as P and As. Considering the flux elements, often the system in question is a quaternary or a higher multinary system, which drastically increases complexity. In this manuscript, on the examples of flux growth of phosphides and arsenides, guidelines of flux selections, existing challenges, and future directions are discussed. We expect that the field will be further developed by applying in situ techniques and computational modeling of the nucleation and growth kinetics. Additionally, leveraging variables other than temperature, such as applied pressure, will make flux growth a more powerful tool in the future.
RESUMO
The unconventional clathrates, Cs8Zn18Sb28 and Cs8Cd18Sb28, were synthesized and reinvestigated. These clathrates exhibit unique and extensive superstructural ordering of the clathrate-I structure that was not initially reported. Cs8Cd18Sb28 orders in the Ia3Ìd space group (no. 230) with 8 times larger volume of the unit cell in which most framework atoms segregate into distinct Cd and Sb sites. The structure of Cs8Zn18Sb28 is much more complicated, with an 18-fold increase of unit cell volume accompanied by significant reduction of symmetry down to P2 (no. 3) monoclinic space group. This structure was revealed by a combination of synchrotron X-ray diffraction and electron microscopy techniques. A full solid solution, Cs8Zn18-x Cd x Sb28, was also synthesized and characterized. These compounds follow Vegard's law in regard to their primitive unit cell sizes and melting points. Variable temperature in situ synchrotron powder X-ray diffraction was used to study the formation and melting of Cs8Zn18Sb28. Due to the heavy elements comprising clathrate framework and the complex structural ordering, the synthesized clathrates exhibit ultralow thermal conductivities, all under 0.8 W m-1 K-1 at room temperature. Cs8Zn9Cd9Sb28 and Cs8Zn4.5Cd13.5Sb28 both have total thermal conductivities of 0.49 W m-1 K-1 at room temperature, among the lowest reported for any clathrate. Cs8Zn18Sb28 has typical p-type semiconducting charge transport properties, while the remaining clathrates show unusual n-p transitions or sharp increases of thermopower at low temperatures. Estimations of the bandgaps as activation energy for resistivity dependences show an anomalous widening and then shrinking of the bandgap with increasing Cd-content.