2D Tungsten Borides Induced Interfacial Modulation Engineering Toward High-Rate Performance Zinc-Iodine Battery.

Aqueous zinc-iodine batteries are promising candidates for large-scale energy storage due to their high energy density and low cost. However, their development is hindered by several drawbacks, including zinc dendrites, anode corrosion, and the shuttle of polyiodides. Here, the design of 2D-shaped tungsten boride nanosheets with abundant borophene subunits-based active sites is reported to guide the (002) plane-dominated deposition of zinc while suppressing side reactions, which facilitates interfacial nucleation and uniform growth of zinc. Meanwhile, the interfacial d-band orbits of tungsten sites can further enhance the anchoring of polyiodides on the surface, to promote the electrocatalytic redox conversion of iodine. The resulting tungsten boride-based I2 cathodes in zinc-iodine cells exhibit impressive cyclic stability after 5000 cycles at 50 C, which accelerates the practical applications of zinc-iodine batteries.

Zinc-Doping Strategy on P2-Type Mn-Based Layered Oxide Cathode for High-Performance Potassium-ion Batteries.

Mn-based layered oxide is extensively investigated as a promising cathode material for potassium-ion batteries due to its high theoretical capacity and natural abundance of manganese. However, the Jahn-Teller distortion caused by high-spin Mn3+ (t2g 3 eg 1 ) destabilizes the host structure and reduces the cycling stability. Here, K0.02 Na0.55 Mn0.70 Ni0.25 Zn0.05 O2 (denoted as KNMNO-Z) is reported to inhibit the Jahn-Teller effect and reduce the irreversible phase transition. Through the implementation of a Zn-doping strategy, higher Mn valence is achieved in the KNMNO-Z electrode, resulting in a reduction of Mn3+ amount and subsequently leading to an improvement in cyclic stability. Specifically, after 1000 cycles, a high retention rate of 97% is observed. Density functional theory calculations reveals that low-valence Zn2+ ions substituting the transition metal position of Mn regulated the electronic structure around the MnO bonding, thereby alleviating the anisotropic coupling between oxidized O2- and Mn4+ and improving the structural stability. K0.02 Na0.55 Mn0.70 Ni0.25 Zn0.05 O2 provided an initial discharge capacity of 57 mAh g-1 at 100 mA g-1 and a decay rate of only 0.003% per cycle, indicating that the Zn-doped strategy is effective for developing high-performance Mn-based layered oxide cathode materials in PIBs.

A Droplet Method for Synthesis of Multiclass Ultrathin Metal Halides.

2D metal halides have attracted increasing research attention in recent years; however, it is still challenging to synthesize them via liquid-phase methods. Here it is demonstrated that a droplet method is simple and efficient for the synthesis of multiclass 2D metal halides, including trivalent (BiI3 , SbI3 ), divalent (SnI2 , GeI2 ), and monovalent (CuI) ones. In particular, 2D SbI3 is first experimentally achieved, of which the thinnest thickness is ≈6 nm. The nucleation and growth of these metal halide nanosheets are mainly determined by the supersaturation of precursor solutions that are dynamically varying during the solution evaporation. After solution drying, the nanosheets can fall on the surface of many different substrates, which further enables the feasible fabrication of related heterostructures and devices. With SbI3 /WSe2 being a good demonstration, the photoluminescence intensity and photo responsivity of WSe2 is obviously enhanced after interfacing with SbI3 . The work opens a new pathway for 2D metal halides toward widespread investigation and applications.

Stimulating and Manipulating Robust Circularly Polarized Photoluminescence in Achiral Hybrid Perovskites.

Circularly polarized light (CPL) is essential for optoelectronic and chiro-spintronic applications. Hybrid perovskites, as star optoelectronic materials, have demonstrated CPL activity, which is, however, mostly limited to chiral perovskites. Here, we develop a simple, general, and efficient strategy to stimulate CPL activity in achiral perovskites, which possess rich species, efficient luminescence, and tunable bandgaps. With the formation of van der Waals heterojunctions between chiral and achiral perovskites, a nonequilibrium spin population and thus CPL activity are realized in achiral perovskites by receiving spin-polarized electrons from chiral perovskites. The polarization degree of room-temperature CPL in achiral perovskites is at least one order of magnitude higher than in chiral ones. The CPL polarization degree and emission wavelengths of achiral perovskites can be flexibly designed by tuning chemical compositions, operating temperature, or excitation wavelengths. We anticipate that unlimited types of achiral perovskites can be endowed with CPL activity, benefiting their applications in integrated CPL sources and detectors.

One-Pot Synthesis of Pomegranate-Structured Fe3 O4 /Carbon Nanospheres-Doped Graphene Aerogel for High-Rate Lithium Ion Batteries.

A unique hierarchically nanostructured composite of iron oxide/carbon (Fe3O4/C) nanospheres-doped three-dimensional (3D) graphene aerogel has been fabricated by a one-pot hydrothermal strategy. In this novel nanostructured composite aerogel, uniform Fe3O4 nanocrystals (5-10 nm) are individually embedded in carbon nanospheres (ca. 50 nm) forming a pomegranate-like structure. The carbon matrix suppresses the aggregation of Fe3O4 nanocrystals, avoids direct exposure of the encapsulated Fe3O4 to the electrolyte, and buffers the volume expansion. Meanwhile, the interconnected 3D graphene aerogel further serves to reinforce the structure of the Fe3O4/C nanospheres and enhances the electrical conductivity of the overall electrode. Therefore, the carbon matrix and the interconnected graphene network entrap the Fe3O4 nanocrystals such that their electrochemical function is retained even after fracture. This novel hierarchical aerogel structure delivers a long-term stability of 634 mA h g(-1) over 1000 cycles at a high current density of 6 A g(-1) (7 C), and an excellent rate capability of 413 mA h g(-1) at 10 A g(-1) (11 C), thus exhibiting great potential as an anode composite structure for durable high-rate lithium-ion batteries.

Fundamentally Manipulating the Electronic Structure of Polar Bifunctional Catalysts for Lithium-Sulfur Batteries: Heterojunction Design versus Doping Engineering.

Heterogeneous structures and doping strategies have been intensively used to manipulate the catalytic conversion of polysulfides to enhance reaction kinetics and suppress the shuttle effect in lithium-sulfur (Li-S) batteries. However, understanding how to select suitable strategies for engineering the electronic structure of polar catalysts is lacking. Here, a comparative investigation between heterogeneous structures and doping strategies is conducted to assess their impact on the modulation of the electronic structures and their effectiveness in catalyzing the conversion of polysulfides. These findings reveal that Co0.125Zn0.875Se, with metal-cation dopants, exhibits superior performance compared to CoSe2/ZnSe heterogeneous structures. The incorporation of low Co2+ dopants induces the subtle lattice strain in Co0.125Zn0.875Se, resulting in the increased exposure of active sites. As a result, Co0.125Zn0.875Se demonstrates enhanced electron accumulation on surface Se sites, improved charge carrier mobility, and optimized both p-band and d-band centers. The Li-S cells employing Co0.125Zn0.875Se catalyst demonstrate significantly improved capacity (1261.3 mAh g-1 at 0.5 C) and cycle stability (0.048% capacity delay rate within 1000 cycles at 2 C). This study provides valuable guidance for the modulation of the electronic structure of typical polar catalysts, serving as a design directive to tailor the catalytic activity of advanced Li-S catalysts.

Interfacial "Double-Terminal Binding Sites" Catalysts Synergistically Boosting the Electrocatalytic Li2S Redox for Durable Lithium-Sulfur Batteries.

Catalytic conversion of polysulfides emerges as a promising approach to improve the kinetics and mitigate polysulfide shuttling in lithium-sulfur (Li-S) batteries, especially under conditions of high sulfur loading and lean electrolyte. Herein, we present a separator architecture that incorporates double-terminal binding (DTB) sites within a nitrogen-doped carbon framework, consisting of polar Co0.85Se and Co clusters (Co/Co0.85Se@NC), to enhance the durability of Li-S batteries. The uniformly dispersed clusters of polar Co0.85Se and Co offer abundant active sites for lithium polysulfides (LiPSs), enabling efficient LiPS conversion while also serving as anchors through a combination of chemical interactions. Density functional theory calculations, along with in situ Raman and X-ray diffraction characterizations, reveal that the DTB effect strengthens the binding energy to polysulfides and lowers the energy barriers of polysulfide redox reactions. Li-S batteries utilizing the Co/Co0.85Se@NC-modified separator demonstrate exceptional cycling stability (0.042% per cycle over 1000 cycles at 2 C) and rate capability (849 mAh g-1 at 3 C), as well as deliver an impressive areal capacity of 10.0 mAh cm-2 even in challenging conditions with a high sulfur loading (10.7 mg cm-2) and lean electrolyte environments (5.8 µL mg-1). The DTB site strategy offers valuable insights into the development of high-performance Li-S batteries.

Thickness-dependent excitonic properties of WSe2/FePS3 van der Waals heterostructures.

van der Waals heterostructures (vdWHs), with their flexible combination of various two-dimensional (2D) materials, are continuously revealing new physics and functionalities. 2D magnetic materials have recently become a focus due to their fascinating electronic and spintronic properties. However, there has rarely been any investigation of the optical properties of 2D magnetic materials-based heterostructures. Herein, we construct a new WSe2/FePS3 heterostructure, in which WSe2 works as a "sensor" to visualize the thickness-dependent properties of FePS3. As characterized by photoluminescence (PL) spectra, whether under or on top of the FePS3, the PL intensity of the monolayer WSe2 is strongly quenched. The quenching effect becomes more obvious as the FePS3 thickness increases. This is because of the efficient charge transfer process occurring at the WSe2/FePS3 interface with type II band alignment, which is faster for thicker FePS3, as is evident from transient absorption measurements. The thickness-dependent charge transfer process and corresponding excitonic properties are further revealed in low-temperature photoluminescence spectra of WSe2/FePS3 heterostructures. Our results show that the thickness of 2D magnetic materials can work as an experimental tuning knob to manipulate the optical performance of conventional 2D semiconductors, endowing van der Waals heterostructures with more unexpected properties and functionalities.

Controlled Synthesis of Sub-Millimeter Nonlayered WO2 Nanoplates via a WSe2 -Assisted Method.

2D metal oxides (2DMOs) have stimulated tremendous attention due to their distinct electronic structures and abundant surface chemistry. However, it remains a standing challenge for the synthesis of 2DMOs because of their intrinsic 3D lattice structure and ultrahigh synthesis temperature. Here, a reliable WSe2 -assisted chemical vapor deposition (CVD) strategy to grow nonlayered WO2 nanoplates with tunable thickness and lateral dimension is reported. Optical microscopy and scanning electron microscopy studies demonstrate that the WO2 nanoplates exhibit a well-faceted rhombic geometry with a lateral dimension up to the sub-millimeter level (≈135 µm), which is the largest size of 2DMO single crystals obtained by CVD to date. Scanning transmission electron microscopy studies reveal that the nanoplates are high-quality single crystals. Electrical measurements show the nanoplates exhibit metallic behavior with strong anisotropic resistance, outstanding conductivity of 1.1 × 106  S m-1 , and breakdown current density of 7.1 × 107  A cm-2 . More interestingly, low-temperature magnetotransport studies demonstrate that the nanoplates show a quantum-interference-induced weak-localization effect. The developed WSe2 -assisted strategy for the growth of WO2 nanoplates can enrich the library of 2DMO materials and provide a material platform for other property explorations based on 2D WO2 .

Recent Advances in Two-Dimensional Magnets: Physics and Devices towards Spintronic Applications.

The emergence of low-dimensional nanomaterials has brought revolutionized development of magnetism, as the size effect can significantly influence the spin arrangement. Since the first demonstration of truly two-dimensional magnetic materials (2DMMs) in 2017, a wide variety of magnetic phases and associated properties have been exhibited in these 2DMMs, which offer a new opportunity to manipulate the spin-based devices efficiently in the future. Herein, we focus on the recent progress of 2DMMs and heterostructures in the aspects of their structural characteristics, physical properties, and spintronic applications. Firstly, the microscopy characterization of the spatial arrangement of spins in 2D lattices is reviewed. Afterwards, the optical probes in the light-matter-spin interactions at the 2D scale are discussed. Then, particularly, we systematically summarize the recent work on the electronic and spintronic devices of 2DMMs. In the section of electronic properties, we raise several exciting phenomena in 2DMMs, i.e., long-distance magnon transport, field-effect transistors, varying magnetoresistance behavior, and (quantum) anomalous Hall effect. In the section of spintronic applications, we highlight spintronic devices based on 2DMMs, e.g., spin valves, spin-orbit torque, spin field-effect transistors, spin tunneling field-effect transistors, and spin-filter magnetic tunnel junctions. At last, we also provide our perspectives on the current challenges and future expectations in this field, which may be a helpful guide for theorists and experimentalists who are exploring the optical, electronic, and spintronic properties of 2DMMs.

Engineering the Phases and Heterostructures of Ultrathin Hybrid Perovskite Nanosheets.

Low-dimensional perovskites have gained increasing attention recently, and engineering their material phases, structural patterning and interfacial properties is crucial for future perovskite-based applications. Here a phase and heterostructure engineering on ultrathin perovskites, through the reversible cation exchange of hybrid perovskites and efficient surface functionalization of low-dimensional materials, is demonstrated. Using PbI2 as precursor and template, perovskite nanosheets of varying thickness and hexagonal shape on diverse substrates is obtained. Multiple phases, such as PbI2 , MAPbI3 and FAPbI3 , can be flexibly designed and transformed as a single nanosheet. A perovskite nanosheet can be patterned using masks made of 2D materials, fabricating lateral heterostructures of perovskite and PbI2 . Perovskite-based vertical heterostructures show strong interfacial coupling with 2D materials. As a demonstration, monolayer MoS2 /MAPbI3 stacks give a type-II heterojunction. The ability to combine the optically efficient perovskites with versatile 2D materials creates possibilities for new designs and functionalities.

Conjugated Cobalt Polyphthalocyanine as the Elastic and Reprocessable Catalyst for Flexible Li-CO2 Batteries.

Li-CO2 batteries represent an attractive solution for electrochemical energy storage by utilizing atmospheric CO2 as the energy carrier. However, their practical viability critically depends on the development of efficient and low-cost cathode catalysts for the reversible formation and decomposition of Li2 CO3 . Here, the great potential of a structurally engineered polymer is demonstrated as the cathode catalyst for rechargeable Li-CO2 batteries. Conjugated cobalt polyphthalocyanine is prepared via a facile microwave heating method. Due to the crosslinked network, it is intrinsically elastic and has improved chemical, physical, and mechanical stability. Electrochemical measurements show that cobalt polyphthalocyanine facilitates the reversible formation and decomposition of Li2 CO3 , and therefore enables high-performance Li-CO2 batteries with large areal capacity and impressive cycling performance. In addition, the elastic and reprocessable property of the polymeric catalyst renders it possible to fabricate flexible batteries.

Rational Synthesis and Assembly of Ni3S4 Nanorods for Enhanced Electrochemical Sodium-Ion Storage.

Even though advocated as the potential low-cost alternatives to current lithium-ion technology, the practical viability of sodium-ion batteries remains illusive and depends on the development of high-performance electrode materials. Very few candidates available at present can simultaneously meet the requirements on capacity, rate capability, and cycle life. Herein, we report a high-temperature solution method to prepare Ni3S4 nanorods with uniform sizes. These colloidal nanorods readily self-assemble side by side and form microsized superstructures, which unfortunately negates the nanoscale feature of individual nanorods. To this end, we further introduce two-dimensional graphene nanosheets as the spacer to interrupt nanorod self-assembly. Resultant composite presents a marked advantage toward electrochemical storage of Na+ ions. We demonstrate that in half-cells it exhibits large reversible specific capacity in excess of 600 mAh/g, high rate capability with >300 mAh/g retained at 4 A/g, and great cycle life at different current rates. This anode material can also be combined with the NASICON-type Na3V2(PO4)3 cathode in full cells to enable large capacity and good cyclability.

Double-sided brush-shaped TiO2 nanostructure assemblies with highly ordered nanowires for dye-sensitized solar cells.

We describe a seeded hydrothermal process for the growth of unique double-sided brush-shaped (DSBS) TiO2 nanostructure assemblies consisting of highly ordered rutile nanowires vertically aligned around an annealed TiO2 nanoparticle layer. The annealed TiO2 nanoparticle layer seeds the nanowire growth and also supports the DSBS structure. The morphology of the DSBS TiO2 nanostructure depends on the hydrothermal reaction time. The diameter of the nanowires is about 6.6 nm, and with increasing reaction time from 1 to 8 h the nanowire length increases from 0.6 to 6.2 µm, whereas the thickness of the nanoparticle layer decreases from 4.3 to 2.8 µm. These free-standing nanowire arrays provide large internal surface area, which is essential for minimizing carrier recombination in high performance photovoltaic devices. Furthermore, the nanowire architecture can help increase the rate of charge transport as compared to particulate films because of lower concentration of grain boundaries. The power conversion efficiency of backside (DSBS TiO2/FTO photoanode) illuminated dye-sensitized solar cells fabricated using the DSBS TiO2 nanostructure assembly is found to be depended on the nanowire length. A cell fabricated using 15.2 µm thick nanostructures sensitized by N719 has a short-circuit current density of 12.18 mA cm(-2), 0.78 V open circuit potential, and a 0.59 filling factor, yielding a maximum power conversion efficiency of 5.61% under AM 1.5 illumination.

Efficient thermolysis route to monodisperse Cu2ZnSnS4 nanocrystals with controlled shape and structure.

Monodisperse Cu2ZnSnS4 (CZTS) nanocrystals with tunable shape, crystalline phase, and composition are synthesized by efficient thermolysis of a single source precursor of mixed metal-oleate complexes in hot organic solvents with dissolved sulfur sources. Suitable tuning of the synthetic conditions and the Cu/(Zn + Sn) ratio of the precursor has enabled precise control of the crystalline phase in the form of kesterite, or a newly observed wurtzite structure. Nanocrystals with morphology in the form of spherical, rice-like, or rod-like shapes are obtained over a wide range of compositions (0.5 ≤ Cu/(Zn + Sn) ≤ 1.2). Both the final products and intermediates for each shape exhibit consistent composition and structure, indicating homogenous nucleation and growth of single-phase nanocrystals. Thin films prepared from colloidal nanocrystal suspensions display interesting shape-dependent photoresponse behavior under white light illumination from a solar simulator.