Towards harmonisation of testing of nanomaterials for EU regulatory requirements on chemical safety - A proposal for further actions.

Over the recent years, EU chemicals legislation, guidance and test guidelines have been developed or adapted for nanomaterials to facilitate safe use of nanomaterials. This paper provides an overview of the information requirements across different EU regulatory areas. For each information requirement, a group of 22 experts identified potential needs for further action to accommodate guidance and test guidelines to nanomaterials. Eleven different needs for action were identified, capturing twenty-two information requirements that are specific to nanomaterials and relevant to multiple regulatory areas. These were further reduced to three overarching issues: 1) resolve issues around nanomaterial dispersion stability and dosing in toxicity testing, in particular for human health endpoints, 2) further develop tests or guidance on degradation and transformation of organic nanomaterials or nanomaterials with organic components, and 3) further develop tests and guidance to measure (a)cellular reactivity of nanomaterials. Efforts towards addressing these issues will result in better fit-for-purpose test methods for (EU) regulatory compliance. Moreover, it secures validity of hazard and risk assessments of nanomaterials. The results of the study accentuate the need for a structural process of identification of information needs and knowledge generation, preferably as part of risk governance and closely connected to technological innovation policy.

Assessing the Lability and Environmental Mobility of Organically Bound Copper by Stable Isotope Dilution.

The environmental mobility of Cu and therefore its potential toxicity are closely linked to its attachment to natural organic matter (NOM). Geochemical models assume full lability of metals bound to NOM, especially under strong oxidizing conditions, which often leads to an overestimation of the lability of soil metals. Stable isotope dilution (SID) has been successfully applied to estimate the labile (isotopically exchangeable) pool of soil metals. However, its application to study the lability of NOM-Cu required development of a robust separation and detection approach so that free Cu ions can be discriminated from (the also soluble) NOM-Cu. We developed a SID protocol (with enriched 65Cu) to quantify the labile pool of NOM-Cu using size exclusion chromatography coupled to a UV detector (for the identification of different NOM molecular weights) and ICP-MS (for 65Cu/63Cu ratio measurement). The Cu isotopic-exchange technique was first characterized and verified using standard NOM (SR-NOM) before applying the developed technique to an "organic-rich" podzol soil extract. The developed protocol indicated that, in contrast to the common knowledge, significant proportions of SR-NOM-Cu (25%) and soil organic-Cu (55%) were not labile, i.e., permanently locked into inaccessible organic structures. These findings need to be considered in defining Cu interactions with the reactive pool of NOM using geochemical models and risk evaluation protocols in which complexed Cu has always been implicitly assumed to be fully labile and exchangeable with free Cu ions.

Methanol-based extraction protocol for insoluble and moderately water-soluble nanoparticles in plants to enable characterization by single particle ICP-MS.

The detection and characterization of soluble metal nanoparticles in plant tissues are an analytical challenge, though a scientific necessity for regulating nano-enabled agrichemicals. The efficacy of two extraction methods to prepare plant samples for analysis by single particle ICP-MS, an analytical method enabling both size determination and quantification of nanoparticles (NP), was assessed. A standard enzyme-based extraction was compared to a newly developed methanol-based approach. Au, CuO, and ZnO NPs were extracted from three different plant leaf materials (lettuce, corn, and kale) selected for their agricultural relevance and differing characteristics. The enzyme-based approach was found to be unsuitable because of changes in the recovered NP size distribution of CuO NP. The MeOH-based extraction allowed reproducible extraction of the particle size distribution (PSD) without major alteration caused by the extraction. The type of leaf tissue did not significantly affect the recovered PSD. Total metal losses during the extraction process were largely due to the filtration step prior to analysis by spICP-MS, though this did not significantly affect PSD recovery. The methanol extraction worked with the three different NPs and plants tested and is suitable for studying the fate of labile metal-based nano-enabled agrichemicals.

Transformations of Nanoenabled Copper Formulations Govern Release, Antifungal Effectiveness, and Sustainability throughout the Wood Protection Lifecycle.

Here we compare the standard European benchmark of wood treatment by molecularly dissolved copper amine (Cu-amine), also referred to as aqueous copper amine (ACA), against two nanoenabled formulations: copper(II)oxide nanoparticles (CuO NPs) in an acrylic paint to concentrate Cu as a barrier on the wood surface, and a suspension of micronized basic copper carbonate (CuCO3·Cu(OH)2) for wood pressure treatment. After characterizing the properties of the (nano)materials and their formulations, we assessed their effects in vitro against three fungal species: Coniophora puteana, Gloeophyllum trabeum, and Trametes versicolor, finding them to be mediated only partially by ionic transformation. To assess the use phase, we quantify both release rate and form. Cu leaching rates for the two types of impregnated wood (conventional and nanoenabled) are not significantly different at 172 ± 6 mg/m2, with Cu being released predominantly in ionic form. Various simulations of outdoor aging with release sampling by runoff, during condensation, by different levels of mechanical shear, all resulted in comparable form and rate of release from the nanoenabled or the molecular impregnated woods. Because of dissolving transformations, the nanoenabled impregnation does not introduce additional concern over and above that associated with the traditional impregnation. In contrast, Cu released from wood coated with the CuO acrylate contained particles, but the rate was at least 100-fold lower. In the same ranking, the effectiveness to protect against the wood-decaying basidiomycete Coniophora puteana was significant with both impregnation technologies but remained insignificant for untreated wood and wood coated by the acrylic CuO. Accordingly, a lifecycle-based sustainability analysis indicates that the CuO acrylic coating is less sustainable than the technological alternatives, and should not be developed into a commercial product.

Microplastic Exposure Assessment in Aquatic Environments: Learning from Similarities and Differences to Engineered Nanoparticles.

Microplastics (MPs) have been identified as contaminants of emerging concern in aquatic environments and research into their behavior and fate has been sharply increasing in recent years. Nevertheless, significant gaps remain in our understanding of several crucial aspects of MP exposure and risk assessment, including the quantification of emissions, dominant fate processes, types of analytical tools required for characterization and monitoring, and adequate laboratory protocols for analysis and hazard testing. This Feature aims at identifying transferrable knowledge and experience from engineered nanoparticle (ENP) exposure assessment. This is achieved by comparing ENP and MPs based on their similarities as particulate contaminants, whereas critically discussing specific differences. We also highlight the most pressing research priorities to support an efficient development of tools and methods for MPs environmental risk assessment.

Impact of Sodium Humate Coating on Collector Surfaces on Deposition of Polymer-Coated Nanoiron Particles.

The affinity between nanoscale zerovalent iron (nano-ZVI) and mineral surfaces hinders its mobility, and hence its delivery into contaminated aquifers. We have tested the hypothesis that the attachment of poly(acrylic acid)-coated nano-ZVI (PAA-nano-ZVI) to mineral surfaces could be limited by coating such surfaces with sodium (Na) humate prior to PAA-nano-ZVI injection. Na humate was expected to form a coating over favorable sites for PAA-nano-ZVI attachment and hence reduce the affinity of PAA-nano-ZVI for the collector surfaces through electrosteric repulsion between the two interpenetrating charged polymers. Column experiments demonstrated that a low concentration (10 mg/L) Na humate solution in synthetic water significantly improved the mobility of PAA-nano-ZVI within a standard sand medium. This effect was, however, reduced in more heterogeneous natural collector media from contaminated sites, as not an adequate amount of the collector sites favorable for PAA-nano-ZVI attachment within these media appear to have been screened by the Na humate. Na humate did not interact with the surfaces of acid-washed glass beads or standard Ottawa sand, which presented less surface heterogeneity. Important factors influencing the effectiveness of Na humate application in improving PAA-nano-ZVI mobility include the solution chemistry, the Na humate concentration, and the collector properties.

Nanoscale Coloristic Pigments: Upper Limits on Releases from Pigmented Plastic during Environmental Aging, In Food Contact, and by Leaching.

The life cycle of nanoscale pigments in plastics may cause environmental or human exposure by various release scenarios. We investigated spontaneous and induced release with mechanical stress during/after simulated sunlight and rain degradation of polyethylene (PE) with organic and inorganic pigments. Additionally, primary leaching in food contact and secondary leaching from nanocomposite fragments with an increased surface into environmental media was examined. Standardized protocols/methods for release sampling, detection, and characterization of release rate and form were applied: Transformation of the bulk material was analyzed by Scanning Electron Microscopy (SEM), X-ray-tomography and Fourier-Transform Infrared spectroscopy (FTIR); releases were quantified by Inductively Coupled Plasma Mass Spectrometry (ICP-MS), single-particle-ICP-MS (sp-ICP-MS), Transmission Electron Microscopy (TEM), Analytical Ultracentrifugation (AUC), and UV/Vis spectroscopy. In all scenarios, the detectable particulate releases were attributed primarily to contaminations from handling and machining of the plastics, and were not identified with the pigments, although the contamination of 4 mg/kg (Fe) was dwarfed by the intentional content of 5800 mg/kg (Fe as Fe2O3 pigment). We observed modulations (which were at least partially preventable by UV stabilizers) when comparing as-produced and aged nanocomposites, but no significant increase of releases. Release of pigments was negligible within the experimental error for all investigated scenarios, with upper limits of 10 mg/m2 or 1600 particles/mL. This is the first holistic confirmation that pigment nanomaterials remain strongly contained in a plastic that has low diffusion and high persistence such as the polyolefin High Density Polyethylene (HDPE).

Nano electrospray gas-phase electrophoretic mobility molecular analysis (nES GEMMA) of liposomes: applicability of the technique for nano vesicle batch control.

Liposomes are biodegradable nanoparticle vesicles consisting of a lipid bilayer encapsulating an aqueous core. Entrapped cargo material is shielded from the extra-vesicular medium and sustained release of encapsulated material can be achieved. However, application of liposomes as nano-carriers demands their characterization concerning size and size distribution, particle-number concentration, occurrence of vesicle building blocks in solution and determination of the resulting vesicle encapsulation capacity. These questions can be targeted via gas-phase electrophoretic mobility molecular analysis (GEMMA) based on a nano electrospray (nES) charge-reduction source. This instrument separates single-charged nanoparticles in the gas-phase according to size in a high-laminar sheath-flow by means of an orthogonal, tunable electric field. nES GEMMA analysis enables to confirm liposome integrity after passage through the instrument (in combination with atomic force microscopy) as well as to exclude vesicle aggregation. Additionally, nanoparticle diameters at peak apexes and size distribution data are obtained. Differences of hydrodynamic and dry particle diameter values, as well as the effect of number- and mass-based concentration data analysis on obtained liposome diameters are shown. Furthermore, the repeatability of liposome preparation is studied, especially upon incorporation of PEGylated lipids in the bilayer. Finally, the instruments applicability to monitor mechanical stress applied to vesicles is demonstrated.

Meeting the Needs for Released Nanomaterials Required for Further Testing-The SUN Approach.

The analysis of the potential risks of engineered nanomaterials (ENM) has so far been almost exclusively focused on the pristine, as-produced particles. However, when considering a life-cycle perspective, it is clear that ENM released from genuine products during manufacturing, use, and disposal is far more relevant. Research on the release of materials from nanoproducts is growing and the next necessary step is to investigate the behavior and effects of these released materials in the environment and on humans. Therefore, sufficient amounts of released materials need to be available for further testing. In addition, ENM-free reference materials are needed since many processes not only release ENM but also nanosized fragments from the ENM-containing matrix that may interfere with further tests. The SUN consortium (Project on "Sustainable Nanotechnologies", EU seventh Framework funding) uses methods to characterize and quantify nanomaterials released from composite samples that are exposed to environmental stressors. Here we describe an approach to provide materials in hundreds of gram quantities mimicking actual released materials from coatings and polymer nanocomposites by producing what is called "fragmented products" (FP). These FP can further be exposed to environmental conditions (e.g., humidity, light) to produce "weathered fragmented products" (WFP) or can be subjected to a further size fractionation to isolate "sieved fragmented products" (SFP) that are representative for inhalation studies. In this perspective we describe the approach, and the used methods to obtain released materials in amounts large enough to be suitable for further fate and (eco)toxicity testing. We present a case study (nanoparticulate organic pigment in polypropylene) to show exemplarily the procedures used to produce the FP. We present some characterization data of the FP and discuss critically the further potential and the usefulness of the approach we developed.

Physicochemical characterization of titanium dioxide pigments using various techniques for size determination and asymmetric flow field flow fractionation hyphenated with inductively coupled plasma mass spectrometry.

Seven commercial titanium dioxide pigments and two other well-defined TiO2 materials (TiMs) were physicochemically characterised using asymmetric flow field flow fractionation (aF4) for separation, various techniques to determine size distribution and inductively coupled plasma mass spectrometry (ICPMS) for chemical characterization. The aF4-ICPMS conditions were optimised and validated for linearity, limit of detection, recovery, repeatability and reproducibility, all indicating good performance. Multi-element detection with aF4-ICPMS showed that some commercial pigments contained zirconium co-eluting with titanium in aF4. The other two TiMs, NM103 and NM104, contained aluminium as integral part of the titanium peak eluting in aF4. The materials were characterised using various size determination techniques: retention time in aF4, aF4 hyphenated with multi-angle laser light spectrometry (MALS), single particle ICPMS (spICPMS), scanning electron microscopy (SEM) and particle tracking analysis (PTA). PTA appeared inappropriate. For the other techniques, size distribution patterns were quite similar, i.e. high polydispersity with diameters from 20 to >700 nm, a modal peak between 200 and 500 nm and a shoulder at 600 nm. Number-based size distribution techniques as spICPMS and SEM showed smaller modal diameters than aF4-UV, from which mass-based diameters are calculated. With aF4-MALS calculated, light-scattering-based "diameters of gyration" (Øg) are similar to hydrodynamic diameters (Øh) from aF4-UV analyses and diameters observed with SEM, but much larger than with spICPMS. A Øg/Øh ratio of about 1 indicates that the TiMs are oblate spheres or fractal aggregates. SEM observations confirm the latter structure. The rationale for differences in modal peak diameter is discussed.

A uniform measurement expression for cross method comparison of nanoparticle aggregate size distributions.

Available measurement methods for nanomaterials are based on very different measurement principles and hence produce different values when used on aggregated nanoparticle dispersions. This paper provides a solution for relating measurements of nanomaterials comprised of nanoparticle aggregates determined by different techniques using a uniform expression of a mass equivalent diameter (MED). The obtained solution is used to transform into MED the size distributions of the same sample of synthetic amorphous silica (nanomaterial comprising aggregated nanoparticles) measured by six different techniques: scanning electron microscopy in both high vacuum (SEM) and liquid cell setup (Wet-SEM); gas-phase electrophoretic mobility molecular analyzer (GEMMA); centrifugal liquid sedimentation (CLS); nanoparticle tracking analysis (NTA); and asymmetric flow field flow fractionation with inductively coupled plasma mass spectrometry detection (AF4-ICP-MS). Transformed size distributions are then compared between the methods and conclusions drawn on methods' measurement accuracy, limits of detection and quantification related to the synthetic amorphous silca's size. Two out of the six tested methods (GEMMA and AF4-ICP-MS) cross validate the MED distributions between each other, providing a true measurement. The measurement accuracy of other four techniques is shown to be compromised either by the high limit of detection and quantification (CLS, NTA, Wet-SEM) or the sample preparation that is biased by increased retention of smaller nanomaterials (SEM). This study thereby presents a successful and conclusive cross-method comparison of size distribution measurements of aggregated nanomaterials. The authors recommend the uniform MED size expression for application in nanomaterial risk assessment studies and clarifications in current regulations and definitions concerning nanomaterials.

River-derived humic substances as iron chelators in seawater.

The speciation of iron(III) in oxic seawater is dominated by its hydrolysis and sedimentation of insoluble iron(III)-oxyhydroxide. As a consequence, many oceanic areas have very low iron levels in surface seawater which leads to iron deficiency since phytoplankton require iron as a micronutrient in order to grow. Fortunately, iron solubility is not truly as low as Fe(III) solubility measurements in inorganic seawater would suggest, since oceanic waters contain organic molecules which tend to bind the iron and keep it in solution. Various iron-binding organic ligands which combine to stabilize dissolved iron have been detected and thoroughly investigated in recent years. However, the role of iron-binding ligands from terrestrial sources remains poorly constrained. Blackwater rivers supply large amounts of natural organic material (NOM) to the ocean. This NOM (which consists mainly of vascular plant-derived humic substances) is able to greatly enhance iron bioavailability in estuaries and coastal regions, however, breakdown processes lead to a rapid decrease of river-derived NOM concentrations with increasing distance from land. It has therefore been argued that the influence of river-derived NOM on iron biogeochemistry in offshore seawater does not seem to be significant. Here we used a standard method based on 59Fe as a radiotracer to study the solubility of Fe(III)-oxyhydroxide in seawater in the presence of riverine NOM. We aimed to address the question how effective is freshwater NOM as an iron chelator under open ocean conditions where the concentration of land-derived organic material is about 3 orders of magnitude smaller than in coastal regions, and does this iron chelating ability vary between NOM from different sources and between different size fractions of the river-borne NOM. Our results show that the investigated NOM fractions were able to substantially enhance Fe(III)-oxyhydroxide solubility in seawater at concentrations of the NOM ≥ 5 µg L- 1. Terrigenous NOM concentrations ≥ 5 µg L- 1 are in no way unusual in open ocean surface waters especially of the Arctic and the North Atlantic Oceans. River-derived humic substances could therefore play a greater role as iron carriers in the ocean than previously thought.

Release of TiO2 nanoparticles from sunscreens into surface waters: a one-year survey at the old Danube recreational Lake.

Monitoring data are necessary for the future production of engineered nanomaterials and the development of regulations for nanomaterials. Therefore, it is necessary to develop methods that reliably detect and quantify nanomaterials in real-world systems at expectedly low concentrations. In this work we tested several methodological approaches to detect titanium dioxide nanomaterials released from sunscreen products into the Old Danube Lake (Vienna, Austria), which is heavily used for recreational activities like bathing and water sports during the summer season. During a 12-month period suspended particulate matter (SPM) was collected from the lake and analyzed using a combination of complementary techniques. By sampling at a location approximately 50 m from the nearest bathing area and at one meter depth from the water surface, we focused on the potentially mobile fraction of the released nanoparticles. We were able to identify titanium dioxide nanoparticles stemming from sunscreens in the suspended matter of the lake using electron microscopy. Bulk analysis of SPM clearly shows an increase of Ti-containing particles during the summer season. These analyses, however, are not able to distinguish sunscreen nanoparticles from natural Ti-bearing nanoparticles. Therefore, Elemental ratios of Ti with Al, V, Ga, Y, Nb, Eu, Ho, Er, Tm, Yb, and Ta as determined by ICPMS and ICPOES, in combination with single particle ICPMS analysis were applied to establish local background values. The observed mild increase of Ti elemental ratios, compared to spring background values indicates that the residence time of released nanomaterials in the water column is rather short. Overall, the advantages and disadvantages of the methods used to detect and characterize the nanomaterials are discussed.

Accessibility of humic-associated Fe to a microbial siderophore: implications for bioavailability.

Microorganisms in aerobic, circum-neutral environments are challenged to acquire sufficient nutrient Fe due to low solubilities of Fe oxides. To overcome this challenge, many aerobic microbes produce low molecular weight (MW) organic ligands, or siderophores, with extremely high Fe-binding affinities. This research expands the existing understanding of siderophore-mediated Fe acquisition from minerals by examining the effects of the siderophore desferrioxamine B (DFOB) on Fe removal from aquatic humic substances (XAD-8-isolated) and other organic matter (OM) isolates (reverse osmosis, RO; and "transphilic", XAD-4) from several rivers including the Suwannee River (GA, USA). Analysis of samples by asymmetrical flow field-flow fractionation (AsFlFFF) with in-line ICP-MS and UV-vis detectors showed that Fe was naturally abundant and primarily associated with intermediate to high MW OM. An excess of DFOB (relative to naturally present Fe) removed ∼ 75% of Fe and shifted the OM MW distribution to lower MWs, perhaps due to removal of "bridging" Fe, although additional mechanistic study of MW shifts is needed. Removal of other OM-associated metals (e.g., Al, Cu, Zn) by DFOB was minimal for all but a few samples. Fe bound to humic substances and other more "transphilic" organic components therefore should be considered readily bioavailable to aerobic, siderophore-producing microorganisms.

Production of reference materials for the detection and size determination of silica nanoparticles in tomato soup.

A set of four reference materials for the detection and quantification of silica nanoparticles (NPs) in food was produced as a proof of principle exercise. Neat silica suspensions were ampouled, tested for homogeneity and stability, and characterized for total silica content as well as particle diameter by dynamic light scattering (DLS), electron microscopy (EM), gas-phase electrophoretic molecular mobility analysis (GEMMA), and field-flow fractionation coupled with an inductively coupled mass spectrometer (FFF-ICPMS). Tomato soup was prepared from ingredients free of engineered nanoparticles and was spiked at two concentration levels with the silica NP suspension. Homogeneity of these materials was found sufficient to act as reference materials and the materials are sufficiently stable to allow long-term storage and distribution at ambient temperature, providing proof of principle of the feasibility of producing liquid food reference materials for the detection of nanoparticles. The spiked soups were characterized for particle diameter by EM and FFF-ICPMS (one material only), as well as for the total silica content. Although questions regarding the trueness of the results from EM and FFF-ICPMS procedures remain, the data obtained indicate that even assigning values should eventually be feasible. The materials can therefore be regarded as the first step towards certified reference materials for silica nanoparticles in a food matrix.

Spot the difference: engineered and natural nanoparticles in the environment--release, behavior, and fate.

The production and use of nanoparticles leads to the emission of manufactured or engineered nanoparticles into the environment. Those particles undergo many possible reactions and interactions in the environment they are exposed to. These reactions and the resulting behavior and fate of nanoparticles in the environment have been studied for decades through naturally occurring nanoparticulate (1-100 nm) and colloidal (1-1000 nm) substances. The knowledge gained from these investigations is nowhere near sufficiently complete to create a detailed model of the behavior and fate of engineered nanoparticles in the environment, but is a valuable starting point for the risk assessment of these novel materials. It is the aim of this Review to critically compare naturally observed processes with those found for engineered systems to identify the "nanospecific" properties of manufactured particles and describe critical knowledge gaps relevant for the risk assessment of manufactured nanomaterials in the environment.

Natural organic matter concentration and hydrochemistry influence aggregation kinetics of functionalized engineered nanoparticles.

Understanding the colloidal stability of functionalized engineered nanoparticles (FENPs) in aquatic environments is of paramount importance in order to assess the risk related to FENPs. In this study, gold nanoparticles (GNPs) of 68 and 43 nm diameter, coated with citrate and 11-mercaptoundecanoic acid (MUA) respectively, were used as models of FENPs. Time-resolved dynamic light scattering was employed to investigate the aggregation kinetics of two types of GNPs. The results show that without Suwannee river natural organic matter (SRNOM), MUA coating resulted in greater stability than citrate coating for GNPs. Cations have a destabilizing effect on both GNPs following the order Ca(2+) ≈ Mg(2+) >> Na(+); different anions (Cl(-) and SO4(2-)) showed no difference in effects. In the fast aggregation regime, adding SRNOM enhanced the stability of MUA-coated GNPs in both Ca(2+) and Mg(2+) solutions. However citrate-coated GNPs were only stabilized in Mg(2+) solution but enhanced aggregation occurred in high Ca(2+) concentration due to interparticle bridging. For the investigated GNPs and in the presence of SRNOM, Ca(2+) does not always act as a strong coagulant. This indicates that for the new materials emerging from the application of nanotechnology the well-described aggregation mechanisms of colloids in the environment require a detailed re-examination.

Effect of pH and stream order on iron and arsenic speciation in boreal catchments.

Riverine transport of iron (Fe) and arsenic (As) is affected by their associations with natural organic matter (NOM) and suspended iron (oxy)hydroxides. Speciation has a strong influence on element transport from the headwaters to the ocean because NOM may be transported over longer distances compared to iron (oxy)hydroxides. We show that Fe speciation changes along the flow path of a boreal watercourse, as water moves from NOM-rich, acidic first-order streams with pH as low as 3.9 to less acidic higher-order systems (up to pH 6.4). Analysis by Flow Field-Flow Fractionation and chemical equilibrium modeling revealed that Fe from wetland-dominated headwaters was mainly exported as Fe-NOM complexes; in catchments with a stream order >1 and with higher pH, Fe was present in Fe-NOM complexes and precipitated as nanoparticulate iron(oxy)hydroxides which aggregated as the pH increased, with their size eventually exceeding the membrane filters cutoff (0.2 µm). The measured NOM-bound Fe decreased with increasing pH, from 0.38 to 0.16 mmol Fe·g(NOM)(-1). The high concentrations of NOM-bound Fe emphasize the importance of boreal catchments to Fe export to the oceans. Concentrations of As in the <0.2 µm fraction but larger than what is usually considered "truly dissolved" (<1000 g·mol(-1)), decreased from 75% to 26% with increasing pH. The As in this size range was mainly associated with NOM but at pH >4.5 became associated with iron(oxy)hydroxides, and its transport thus became more coupled to that of the iron(oxy)hydroxides downstream in the circumneutral streams.

Detection and characterization of silver nanoparticles in chicken meat by asymmetric flow field flow fractionation with detection by conventional or single particle ICP-MS.

A method of analysis of silver nanoparticles (AgNPs) in chicken meat was developed. The homogenized chicken meat sample, which was spiked with AgNPs, was subjected to enzymolysis by Proteinase K for 40 min at 37 °C. Transmission electron microscopy and inductively coupled plasma mass spectrometry (ICP-MS) in single particle mode were used to characterize the number-based size distribution of AgNPs in the meat digestate. Because similar size distributions were found in the meat digestate and in the aqueous suspension of AgNPs used for spiking the meat, it was shown that no detectable dissolution of the AgNPs took place during the sample preparation stage. The digestate was injected into the asymmetric flow field flow fractionation (AF(4)) -ICP-MS system, which enabled fractionation of nanoparticles from the remaining meat matrix, and resulted in one large peak in the fractograms as well as two smaller peaks eluting close to the void volume. The recovery of silver contained in the large AgNP peak was around 80%. Size determination of AgNPs in the meat matrix, based on external size calibration of the AF(4) channel, was hampered by non-ideal (early elution) behavior of the AgNPs. Single particle ICP-MS was applied for determination of the number-based particle size distribution of AgNPs in collected fractions. The presented work describes for the first time the coupling of AF(4) and ICP-MS for AgNP separation in a food matrix.

Natural organic matter and iron export from the Tanner Moor, Austria.

Samples from a pristine raised peat bog runoff in Austria, the Tannermoor creek, were analysed for their iron linked to natural organic matter (NOM) content. Dissolved organic carbon < 0.45 µm (DOC) was 41-64 mg L-1, iron 4.4-5.5 mg L-1. Samples were analysed applying asymmetric field flow fractionation (AsFlFFF) coupled to UV-vis absorption, fluorescence and inductively coupled plasma mass spectrometry (ICP-MS). The samples showed an iron peak associated with the NOM peak, one sample exhibiting a second peak of iron independent from the NOM peak. As highland peat bogs with similar climatic conditions and vegetation to the Tanner Moor are found throughout the world, including areas adjacent to the sea, we examined the behaviour of NOM and iron in samples brought to euhaline (35‰) conditions with artificial sea salt. The enhanced ionic strength reduced NOM by 53% and iron by 82%. Size exclusion chromatography (SEC) of the samples at sea-like salinity revealed two major fractions of NOM associated with different iron concentrations. The larger one, eluting sharply after the upper exclusion limits of 4000-5000 g mol-1, seems to be most important for iron chelating. The results outline the global importance of sub-mountainous and mountainous raised peat bogs as a source of iron chelators to the marine environment at sites where such peat bogs release their run-offs into the sea.