One-Step Formation of Targeted Liposomes in a Versatile Microfluidic Mixing Device.

Targeted liposomes, as a promising carrier, have received tremendous attention in COVID-19 vaccines, molecular imaging, and cancer treatment, due to their enhanced cellular uptake and payload accumulation at target sites. However, the conventional methods for preparing targeted liposomes still suffer from limitations, including complex operation, time-consuming, and poor reproducibility. Herein, a facile and scalable strategy is developed for one-step construction of targeted liposomes using a versatile microfluidic mixing device (MMD). The engineered MMD provides an advanced synthesis platform for multifunctional liposome with high production rate and controllability. To validate the method, a programmed death-ligand 1 (PD-L1)-targeting aptamer modified indocyanine green (ICG)-liposome (Apt-ICG@Lip) is successfully constructed via the MMD. ICG and the PD-L1-targeting aptamer are used as model drug and targeting moiety, respectively. The Apt-ICG@Lip has high encapsulation efficiency (89.9 ± 1.4%) and small mean diameter (129.16 ± 5.48 nm). In vivo studies (PD-L1-expressing tumor models) show that Apt-ICG@Lip can realize PD-L1 targeted photoacoustic imaging, fluorescence imaging, and photothermal therapy. To verify the versatility of this approach, various targeted liposomes with different functions are further prepared and investigated. These experimental results demonstrate that this method is concise, efficient, and scalable to prepare multifunctional targeted liposomal nanoplatforms for molecular imaging and disease theranostics.

Examination of the effect of niosome preparation methods in encapsulating model antigens on the vesicle characteristics and their ability to induce immune responses.

Niosome nanoparticles can be prepared using different methods, each of which can affect the size and homogeneity of the prepared particles. The aim of this study was to establish if the method of preparation impacted on the prepared vesicles when loaded with a model protein and the type of immune responses induced to the vaccine antigen. Niosomes were prepared using both the traditional thin film hydration (TFH) technique and the microfluidic mixing (MM) technique. Influenza antigen was then entrapped in the niosomes and formulations tested for their ability to induce in vivo immune responses in immunised BALB/c mice. Niosomes prepared by MM had a mean size of 157 ± 1.8 nm and were significantly more uniform compared with the niosomes prepared using TFH (mean size 388 ± 10 nm). Niosomes play a key role as an adjuvant to help raise high antibody immune responses. This was confirmed in this study since animals treated with both types of niosomes and antigen were more responsive than unentrapped (free) antigen. Cytokine analysis showed that the TFH niosomes induced a Th1 immune response by raising IgG2a and high levels of IFN-É£, while the MM niosomes induced a Th2 immune response by inducing IgG1 (p < .05). These results confirmed that the method of preparation of the niosomes nanoparticles induced different immune responses and the average particle size of the niosomes differed depending on the method of manufacture. This indicates that particle size and uniformity are of importance and should be taken into consideration when designing an oral based delivery system for vaccine delivery.

Microfluidic Templating of Spatially Inhomogeneous Protein Microgels.

3D scaffolds in the form of hydrogels and microgels have allowed for more native cell-culture systems to be developed relative to flat substrates. Native biological tissues are, however, usually spatially inhomogeneous and anisotropic, but regulating the spatial density of hydrogels at the microscale to mimic this inhomogeneity has been challenging to achieve. Moreover, the development of biocompatible synthesis approaches for protein-based microgels remains challenging, and typical gelation conditions include UV light, extreme pH, extreme temperature, or organic solvents, factors which can compromise the viability of cells. This study addresses these challenges by demonstrating an approach to fabricate protein microgels with controllable radial density through microfluidic mixing and physical and enzymatic crosslinking of gelatin precursor molecules. Microgels with a higher density in their cores and microgels with a higher density in their shells are demonstrated. The microgels have robust stability at 37 °C and different dissolution rates through enzymolysis, which can be further used for gradient scaffolds for 3D cell culture, enabling controlled degradability, and the release of biomolecules. The design principles of the microgels could also be exploited to generate other soft materials for applications ranging from novel protein-only micro reactors to soft robots.

Cationic lipid/DNA complexes manufactured by microfluidics and bulk self-assembly exhibit different transfection behavior.

Recent advances in biochemical and biophysical research have been achieved through the employment of microfluidic devices. Microfluidic mixing of therapeutic agents with biomaterials yields systems with finely tuned physical-chemical properties for applications in drug and gene delivery. Here, we investigate the role of preparation technology (microfluidic mixing vs. bulk self-assembly) on the transfection efficiency (TE) and cytotoxicity of multicomponent cationic liposome/DNA complexes (lipoplexes) in live Chinese hamster ovarian (CHO) cells. Decoupling TE and cytotoxicity allowed us to combine them in a unique coherent vision. While bulk self-assembly produces highly efficient and highly toxic MC lipoplexes, microfluidics manufacture leads to less efficient, but less cytotoxic complexes. This discrepancy is ascribed to two main factors controlling lipid-mediated cell transfection, i.e. the lipoplex concentration at the cell surface and the lipoplex arrangement at the nanoscale. Further research is required to optimize microfluidic manufacturing of lipoplexes to obtain highly efficient and not cytotoxic gene delivery systems.

Active mixing of complex fluids at the microscale.

Mixing of complex fluids at low Reynolds number is fundamental for a broad range of applications, including materials assembly, microfluidics, and biomedical devices. Of these materials, yield stress fluids (and gels) pose the most significant challenges, especially when they must be mixed in low volumes over short timescales. New scaling relationships between mixer dimensions and operating conditions are derived and experimentally verified to create a framework for designing active microfluidic mixers that can efficiently homogenize a wide range of complex fluids. Active mixing printheads are then designed and implemented for multimaterial 3D printing of viscoelastic inks with programmable control of local composition.

Production of limit size nanoliposomal systems with potential utility as ultra-small drug delivery agents.

Previous studies from this group have shown that limit size lipid-based systems--defined as the smallest achievable aggregates compatible with the packing properties of their molecular constituents--can be efficiently produced using rapid microfluidic mixing technique. In this work, it is shown that similar procedures can be employed for the production of homogeneously sized unilamellar vesicular systems of 30-40 nm size range. These vesicles can be remotely loaded with the protonable drug doxorubicin and exhibit adequate drug retention properties in vitro and in vivo. In particular, it is demonstrated that whereas sub-40 nm lipid nanoparticle (LNP) systems consisting entirely of long-chain saturated phosphatidylcholines cannot be produced, the presence of such lipids may have a beneficial effect on the retention properties of limit size systems consisting of mixed lipid components. Specifically, a 33-nm diameter doxorubicin-loaded LNP system composed of 1-palmitoyl-2-oleoyl phosphatidylcholine (POPC), 1,2-dipalmitoyl phosphatidylcholine (DPPC), cholesterol, and PEGylated lipid (DSPE-PEG2000) demonstrated adequate, stable drug retention in the circulation, with a half-life for drug release of ∼ 12 h. These results indicate that microfluidic mixing is the technique of choice for the production of bilayer LNP systems with sizes less than 50 nm that could lead to development of a novel class of ultra-small drug delivery vehicles.

Paclitaxel-loaded niosomes in combination with metformin: development, characterization and anticancer potentials.

Aim: This study aims to assess the efficacy of free and niosomes-loaded paclitaxel combined with the anti-diabetic drug metformin. Methods: Paclitaxel was successfully encapsulated in all niosome formulations, using microfluidic mixing, with a maximum encapsulation efficiency of 11.9%. Results: The half maximal inhibitory concentration (IC50) for free paclitaxel in T47D cells was significantly reduced from 0.2 to 0.048 mg/ml when combined with metformin 40 mg. The IC50 of paclitaxel was significantly reduced when loaded in niosomes to less than 0.06 mg/ml alone or with metformin. Conclusion: Paclitaxel combination (free or loaded into niosomes) with metformin significantly improved the anticancer efficacy of paclitaxel, which can serve as a method to reduce the paclitaxel dose and its associated side effects.

Pegylated liposome encapsulating docetaxel using microfluidic mixing technique: Process optimization and results in breast cancer models.

The development of nanoparticles could help to improve the efficacy/toxicity balance of drugs. This project aimed to develop liposomes and immunoliposomes using microfluidic mixing technology.Various formulation tests were carried out to obtain liposomes that met the established specifications. The liposomes were then characterized in terms of size, polydispersity index (PDI), docetaxel encapsulation rate and lamellarity. Antiproliferative activity was tested in human breast cancer models ranging from near-negative (MDA-MB-231), positive (MDA-MB-453) to HER2 positive. Pharmacokinetic studies were performed in C57BL/6 mice.Numerous batches of liposomes were synthesised using identical molar ratios and by varying the microfluidic parameters TFR, FRR and buffer. All synthesized liposomes have a size < 200 nm, but only Lipo-1, Lipo-6, Lipo-7, Lipo-8 have a PDI < 0.2, which meets our initial requirements. The size of the liposomes was correlated with the total FRR, for a 1:1 FRR the size is 122.2 ± 12.3 nm, whereas for a 1:3 FRR the size obtained is 163.4 ± 34.0 nm (p = 0.019. Three batches of liposomes were obtained with high docetaxel encapsulation rates > 80 %. Furthermore, in vitro studies on breast cancer cell lines demonstrated the efficacy of liposomes obtained by microfluidic mixing technique. These liposomes also showed improved pharmacokinetics compared to free docetaxel, with a longer half-life and higher AUC (3-fold and 3.5-fold increase for the immunoliposome, respectively).This suggests that switching to the microfluidic process will produce batches of liposomes with the same characteristics in terms of in vitro properties and efficacy, as well as the ability to release the encapsulated drug over time in vivo. This time-efficiency of the microfluidic technique is critical, especially in the early stages of development.

Dialysis-functionalized microfluidic platform for in situ formation of purified liposomes.

Continuous-flow microfluidic devices have been extensively used for producing liposomes due to their high controllability and efficient synthesis processes. However, traditional methods for liposome purification, such as dialysis, gel chromatography, and ultrafiltration, are incompatible with microfluidic devices, which would dramatically restrict the efficiency of liposome synthesis. In this study, we developed a dialysis-functionalized microfluidic platform (DFMP) for in situ formation of purified drug-loaded liposomes. The device was successfully fabricated by using a high-resolution projection micro stereolithography (PµSL) 3D printer. The integrated DFMP consists of a microfluidic mixing unit, a microfluidic dialysis unit, and a dialysis membrane, enabling the liposome preparation and purification in one device. The purified ICG-loaded liposomes prepared by DFMP had a smaller size (264.01±5.34 nm to 173.93±10.71 nm) and a higher encapsulation efficiency (EE) (43.53±0.07% to 46.07±0.67%). In vivo photoacoustic (PA) imaging experiment demonstrated that ICG-loaded liposomes purified with microfluidic dialysis exhibited a stronger penetration and accumulation (2-3 folds) in tumor sites. This work provides a new strategy for one-step production of purified drug-loaded liposomes.

A Basic Method for Formulating mRNA-Lipid Nanoparticle Vaccines in the Lab.

During recent years, RNA therapeutics have begun to make a substantial impact in the clinic, with the approval of the siRNA-based therapeutic Patisiran in 2018, and of the two mRNA SARS-CoV-2 vaccines, BNT162b2 and mRNA-1273 in 2021. A key to the success of these therapeutics lies in the lipid-based delivery system. The therapeutic RNAs are encapsulated in lipid nanoparticles (LNPs), which protect against enzymatic degradation and efficiently deliver the RNA across the cell membrane into the cytosol. Thereby, the method used for LNP synthesis and its lipid composition are crucial aspects that decide the efficacy of the LNP-RNA hetero system. Here we provide a detailed guide for the simple preparation of LNP-encapsulated mRNA vaccines.

The impact of solvent selection on the characteristics of niosome nanoparticles prepared by microfluidic mixing.

The aim of this work was to assess the impact of solvent selection on the characteristics of niosomes prepared by microfluidic mixing. To achieve this, niosomes were manufactured using bench-scale microfluidic mixing systems by changing the type of aqueous and/or organic solvents used to prepare the particles. Niosomes were prepared using different non-ionic surfactants and cholesterol compositions with different solvents and evaluated to investigate the influence of organic and aqueous solvents on the particle's physiochemical characteristics. Here we demonstrated that the solvent selection is a key factor to be considered during the preparation of niosomes with microfluidic mixing. The type of organic solvent was shown to significantly affect the size and the size distribution of the prepared particles. In general, niosome size increased with increasing organic solvent polarity, without affecting the niosomes stability. Moreover, changing the aqueous solvent used to hydrate the lipid components significantly (p < 0.05) affected the characteristics of the prepared niosomes in terms of particles size, size distribution, and surface charge. This impact of solvent selection on the final product is dependent on the lipid components where niosomes prepared with different compositions will have different characteristics when changing the type of organic and/or aqueous solvents. The apparent encapsulation efficiency of quinine as a model hydrophobic drug was subsequently shown to be significantly (p < 0.05) affected by the type of the organic solvent used to prepare the niosomes, while the impact of the organic solvent had less impact on the apparent encapsulation of atenolol as a model hydrophilic drug.

Indocyanine Green-Loaded Liposomes-Assisted Photoacoustic Computed Tomography for Evaluating In Vivo Tumor Penetration of Liposomal Nanocarriers.

Liposomes possess the potential to enhance drug solubility, prolong the duration of circulation, and augment drug accumulation at the tumor site through passive and active targeting strategies. However, there is a lack of studies examining the in vivo tumor penetration capabilities of liposomes of varying sizes, which hampers the development of drug delivery systems utilizing liposomal nanocarriers. Here, we present an indocyanine green (ICG)-loaded liposomes-assisted photoacoustic computed tomography (PACT) for directly evaluating the tumor penetration ability of liposomal nanocarriers in vivo. Through the utilization of microfluidic mixing combined with extrusion techniques, we successfully prepare liposomes encapsulating ICG in both large (192.6 ± 8.0 nm) and small (61.9 ± 0.6 nm) sizes. Subsequently, we designed a dual-wavelength PACT system to directly monitor the in vivo tumor penetration of large- and small-size ICG-encapsulated liposomes. In vivo PACT experiments indicate that ICG-loaded liposomes of smaller size exhibit enhanced penetration capability within tumor tissues. Our work presents a valuable approach to directly assess the penetration ability of liposomal nanocarriers in vivo, thereby facilitating the advancement of drug delivery systems with enhanced tumor penetration and therapeutic efficacy.

The role of formulation approaches in presenting targeting ligands on lipid nanoparticles.

Aims: The density of functional ligands on lipid nanoparticles (LNPs) greatly determined its capability of postfunctionalization and targetability for the applications of personalized nanomedicine and drug/gene delivery. This work is to investigate whether and how formulation methods influence the presentation of surface ligands. Methods: Biotin-modified LNPs as a functional LNP model were synthesized by four different formulation methods. The biotin ligand density and targetability of biotin-LNPs were evaluated and compared. Results: Both the ligand density and targetability of biotin-LNPs formulated by four different formulation methods exhibited a similar trend: homogenization > extrusion > wave-shaped micromixer ≈ Y-shaped micromixer. Conclusion: Formulation methods could modulate the presentation of targeting ligands on LNPs, which could guide future formulation screening and nanomedicine engineering.

Method of manufacturing CAF®09 liposomes affects immune responses induced by adjuvanted subunit proteins.

The ability to induce antigen-specific CD4+ and CD8+T-cell responses is one of the fundamental requirements when developing new efficacious vaccines against challenging infectious diseases and cancer. However, no adjuvants are currently approved for human subunit vaccines that induce T-cell immunity. Here, we incorporated a Toll-like receptor 4 agonist, i.e., the ionizable lipidoid L5N12, in the liposomal cationic adjuvant formulation 09 (CAF®09), and found that modified CAF®09 liposomes possess preserved adjuvant function as compared to unmodified CAF®09. CAF®09 consists of the cationic lipid dimethyldioctadecylammonium (DDA), monomycoloyl glycerol analogue 1 (MMG-1), and polyinosinic:polycytidylic acid [poly(I:C)]. By using the microfluidic mixing technology for liposome preparation, we gradually replaced DDA with L5N12, while keeping the molar ratios of MMG-1 and poly(I:C) constant. We found that this type of modification resulted in colloidally stable liposomes, which were significantly smaller and displayed reduced surface charge as compared to unmodified CAF®09, prepared by using the conventional thin film method. We showed that incorporation of L5N12 decreases the membrane rigidity of CAF®09 liposomes. Furthermore, vaccination with antigen adjuvanted with L5N12-modified CAF®09 or antigen adjuvanted with unmodified CAF®09, respectively, induced comparable antigen-specific serum antibody titers. We found that antigen adjuvanted with L5N12-modified CAF®09 induced antigen-specific effector and memory CD4+ and CD8+T-cell responses in the spleen comparable to those induced when unmodified CAF®09 was used as adjuvant. However, incorporating L5N12 did not have a synergistic immunopotentiating effect on the antibody and T-cell responses induced by CAF®09. Moreover, vaccination with antigen adjuvanted with unmodified CAF®09, which was manufactured by using microfluidic mixing, induced significantly lower antigen-specific CD4+ and CD8+T-cell responses than vaccination with antigen adjuvanted with unmodified CAF®09, which was prepared by using the thin film method. These results show that the method of manufacturing affects CAF®09 liposome adjuvanted antigen-specific immune responses, which should be taken into consideration when evaluating immunogenicity of subunit protein vaccines.

Characterisation of niosome nanoparticles prepared by microfluidic mixing for drug delivery.

Lipid nanoparticles have gained much attention due to their potential as drug delivery systems. They are safe, effective, and be targeted to particular tissues to deliver their payload. Niosomes are one type of lipid nanoparticles that comprise non-ionic surfactants which have proven to be effective due to their stability and biocompatibility. Different manufacturing processes have been reported for niosome preparation, but many of them are not scalable or reproducible for pharmaceutical use. In this study, microfluidic mixing was used to prepare niosomes with different lipid compositions by changing the type of non-ionic surfactant. Niosomes were evaluated for their physicochemical characteristics, morphology, encapsulation efficacy, release profiles of atenolol as a model hydrophilic compound, and cytotoxic activities. Microfluidic mixing allows for particle self-assembly and drug loading in a single step, without the need for post-preparation size reduction. Depending on the lipid composition, the empty particles were <90 nm in size with a uniform distribution. A slight but not significant increase in these values was observed when loading atenolol in most of the prepared formulations. All formulations were spherical and achieved variable levels of atenolol encapsulation. Atenolol release was slow and followed the Korsmeyer-Peppas model regardless of the surfactant type or the percentage of cholesterol used.

Microfluidic Synthesis of a Bioactive Metal-Organic Framework for Glucose-Responsive Insulin Delivery.

In the current study, we report the microfluidic synthesis of a metal-organic framework (MOF) for insulin delivery based on the stimulus response of glucose. Insulin- and gold nanoparticle (AuNP)-encapsulated zeolitic imidazolate framework-8 (ZIF-8) was synthesized using a continuous-flow, microfluidic mixing system via a single-step process. Glucose oxidase mimicking the activity of AuNPs was utilized for oxidizing glucose molecules that entered the porous ZIF-8. The AuNPs oxidized glucose into gluconic acid and hydrogen peroxide inside the MOF (Ins-AuNP-ZIF-8). The resulting acidic pH led to the disruption of ZIF-8 and released insulin. Thus, the presence of glucose molecules provided a stimulus for insulin release. The bioactive MOFs were characterized for the presence of functional groups, morphology, crystallinity, size, and elemental confirmation. The presence of fluorescein-5-isothiocyanate-labeled insulin in the composite was confirmed using confocal laser scanning microscopy. The loading of insulin per unit weight of the MOF, determined by size-exclusion-high-performance liquid chromatography, was 77 and 88% in the batch and microfluidic processes, respectively. Drug release studies confirmed the response of the MOFs to glucose, which triggered insulin release. The synthesis process did not affect the characteristics and application of ZIF-8 and Ins-AuNP-ZIF-8. This study involving the facile synthesis of bioactive MOFs offers a sustainable strategy to design stimulus-responsive drug delivery systems and could be exploited for biosensing applications.

PEG-Free Polyion Complex Nanocarriers for Brain-Derived Neurotrophic Factor.

Many therapeutic formulations incorporate poly(ethylene glycol) (PEG) as a stealth component to minimize early clearance. However, PEG is immunogenic and susceptible to accelerated clearance after multiple administrations. Here, we present two novel reformulations of a polyion complex (PIC), originally composed of poly(ethylene glycol)113-b-poly(glutamic acid)50 (PEG-PLE) and brain-derived neurotrophic factor (BDNF), termed Nano-BDNF (Nano-BDNF PEG-PLE). We replace the PEG based block copolymer with two new polymers, poly(sarcosine)127-b-poly(glutamic acid)50 (PSR-PLE) and poly(methyl-2-oxazolines)38-b-poly(oxazolepropanoic acid)27-b-poly(methyl-2-oxazoline)38 (PMeOx-PPaOx-PMeOx), which are driven to association with BDNF via electrostatic interactions and hydrogen bonding to form a PIC. Formulation using a microfluidic mixer yields small and narrowly disperse nanoparticles which associate following similar principles. Additionally, we demonstrate that encapsulation does not inhibit access by the receptor kinase, which affects BDNF's physiologic benefits. Finally, we investigate the formation of nascent nanoparticles through a series of characterization experiments and isothermal titration experiments which show the effects of pH in the context of particle self-assembly. Our findings indicate that thoughtful reformulation of PEG based, therapeutic PICs with non-PEG alternatives can be accomplished without compromising the self-assembly of the PIC.

Study on the Motion Characteristics of Solid Particles in Fine Flow Channels by Ultrasonic Cavitation.

Microjets caused by the cavitation effect in microchannels can affect the motion trajectory of solid particles in microchannels under ultrasonic conditions. The optimal parameters for an observation experiment were obtained through simulations, and an experiment was designed to verify these parameters. When the cavitation bubbles collapse in the near-wall area, the solid particles in the microchannel can be displaced along the expected motion trajectory. Using fluent software to simulate the bubble collapse process, it can be seen that, when an ultrasonic sound pressure acts on a bubble near the wall, the pressure causes the top of the bubble wall to sink inward and eventually penetrate the bottom of the bubble wall, forming a high-speed microjet. The maximum speed of the jet can reach nearly 28 m/s, and the liquid near the top of the bubble also moves at a high speed, driving the particles in the liquid towards the wall. A high-speed camera was used to observe the ultrasonic cavitation process of bubbles in the water to verify the simulation results. A comparison of particle motion with and without ultrasonic waves proved the feasibility of using the ultrasonic cavitation effect to guide small particles towards the wall. This method provides a novel experimental basis for changing the fluid layer state in the microchannel and improving precision machining.

Spermidine/Spermine N1-Acetyltransferase 1 (SAT1)-A Potential Gene Target for Selective Sensitization of Glioblastoma Cells Using an Ionizable Lipid Nanoparticle to Deliver siRNA.

Spermidine/spermine N1-acetyltransferase 1 (SAT1) responsible for cell polyamine catabolism is overexpressed in glioblastoma multiforme (GB). Its role in tumor survival and promoting resistance towards radiation therapy has made it an interesting target for therapy. In this study, we prepared a lipid nanoparticle-based siRNA delivery system (LNP-siSAT1) to selectively knockdown (KD) SAT1 enzyme in a human glioblastoma cell line. The LNP-siSAT1 containing ionizable DODAP lipid was prepared following a microfluidics mixing method and the resulting nanoparticles had a hydrodynamic size of around 80 nm and a neutral surface charge. The LNP-siSAT1 effectively knocked down the SAT1 expression in U251, LN229, and 42MGBA GB cells, and other brain-relevant endothelial (hCMEC/D3), astrocyte (HA) and macrophage (ANA-1) cells at the mRNA and protein levels. SAT1 KD in U251 cells resulted in a 40% loss in cell viability. Furthermore, SAT1 KD in U251, LN229 and 42MGBA cells sensitized them towards radiation and chemotherapy treatments. In contrast, despite similar SAT1 KD in other brain-relevant cells no significant effect on cytotoxic response, either alone or in combination, was observed. A major roadblock for brain therapeutics is their ability to cross the highly restrictive blood-brain barrier (BBB) presented by the brain microcapillary endothelial cells. Here, we used the BBB circumventing approach to enhance the delivery of LNP-siSAT1 across a BBB cell culture model. A cadherin binding peptide (ADTC5) was used to transiently open the BBB tight junctions to promote paracellular diffusion of LNP-siSAT1. These results suggest LNP-siSAT1 may provide a safe and effective method for reducing SAT1 and sensitizing GB cells to radiation and chemotherapeutic agents.

Microfluidic mixing: a review.

The aim of microfluidic mixing is to achieve a thorough and rapid mixing of multiple samples in microscale devices. In such devices, sample mixing is essentially achieved by enhancing the diffusion effect between the different species flows. Broadly speaking, microfluidic mixing schemes can be categorized as either "active", where an external energy force is applied to perturb the sample species, or "passive", where the contact area and contact time of the species samples are increased through specially-designed microchannel configurations. Many mixers have been proposed to facilitate this task over the past 10 years. Accordingly, this paper commences by providing a high level overview of the field of microfluidic mixing devices before describing some of the more significant proposals for active and passive mixers.