Modified Screen Printed Electrode Suitable for Electrochemical Measurements in Gas Phase.

We describe a convenient assembly for screen printed carbon electrodes (SPCE) suitable for analyses in gaseous samples which are of course lacking in supporting electrolytes. It consists of a circular crown of filter paper, soaked in a RTIL or a DES, placed upon a disposable screen printed carbon cell, so as to contact the outer edge of the carbon disk working electrode, as well as peripheral counter and reference electrodes. The electrical contact between the paper crown soaked in RTIL or DES and SPCE electrodes is assured by a gasket, and all components are installed in a polylactic acid holder. As a result of this configuration, a sensitive, fast-responding, membrane-free gas sensor is achieved where the real working electrode surface is the boundary zone of the carbon working disk contacted by the paper crown soaked in the polyelectrolyte. This assembly provides a portable and disposable electrochemical platform, assembled by the easy immobilization onto a porous and inexpensive supporting material such as paper of RTILs or DESs which are characterized by profitable electrical conductivity and negligible vapor pressure. The electroanalytical performance of this device was evaluated by voltammetric and flow injection analyses of oxygen which was chosen as prototype of electroactive gaseous analytes. The results obtained pointed out that this assembly is very profitable for the analysis of gaseous atmospheres, especially when used as detector for FIA in gaseous streams.

Digitally Controlled Procedure for Assembling Fully Drawn Paper-Based Electroanalytical Platforms.

A simple, reliable, and low-cost fabrication method is proposed here for assembling paper-based electrochemical devices (PEDs) using a commercial desktop digitally controlled plotter/cutter, together with ordinary writing tools. Permanent markers (tips of 1 mm) were used to create effective hydrophobic barriers on paper, while micromechanical pencils (mounting 4B graphite leads, 0.5 mm in diameter) were adopted for automatically drawn precise reference, counter, and working carbon electrodes. Fabrication parameters, such as writing pressure and speed, were first optimized, and the electrochemical performance of these devices was then evaluated by using potassium hexacyanoferrate(II) as redox probe. The good interdevice reproducibility (4.8%) displayed by the relevant voltammetric responses confirmed that this strategy can be profitably adopted to easily assemble paper-based electrochemical devices in a highly flexible manner. The simplicity of the instrumentation used and the low cost of each single device (about $0.04), together with the speed of fabrication (about 2 min), are other important features of the proposed strategy. Finally, to confirm the effectiveness of this prototyping method for the analysis of real samples and rapid controls, PEDs assembled by this simple approach were successfully exploited for the analysis of vitamin B6 in food supplements.

Simple pencil-drawn paper-based devices for one-spot electrochemical detection of electroactive species in oil samples.

We propose here simple electrochemical cells assembled with electrodes pencil drawn on paper for conducting one-spot tests enabling olive oil to be easily distinguished from other vegetable oils. They consist of small circular pads of hydrophilic paper defined by hydrophobic barriers, these last printed by using custom-designed rubber stamps, where working, reference, and counterelectrodes are drawn by pencil leads. These cells were first wetted with a small volume of aqueous electrolyte, avoiding coating of the upper surface of electrodes. A controlled volume of edible oil samples was then applied on top of the moist cell. The results found proved that these devices can be adopted as effective platforms suitable for the detection of electroactive compounds present in edible oils. In fact, they allow voltammetric profiles to be recorded not only for the oxidation of water soluble species (ortho-diphenols, as well as some monophenols and polyphenols) present in olive oils, but also for electroactive hydrophobic components (e.g., α-tocopherol) present in sunflower oils, which were chosen as model of seed oils. The whole of collected findings pointed out that simple one-spot tests performed by these devices enable olive oils to be easily distinguished from other edible oils on the basis of their clearly different voltammetric profiles. A satisfactory interdevice reproducibility (±13%) was estimated by applying strictly similar extra virgin olive oil samples onto seven different cells carefully prepared by the same procedure. An operating mechanism able to account for the detection of also electroactive hydrophobic compounds present in oils is proposed.

Lab-on kit: A 3D printed portable device for optical and electrochemical dual-mode detection.

The hyphenation of electrochemical methods and optical methods in a single portable device is expected to be a challenging combination to enhance the information which can be gained on complex chemical systems. In this paper, a low-cost spectrophotometric device based on low-cost electronics integrated with an electroanalytical cell equipped with a screen printed electrode (SPE) and assembled exploiting a DIY approach, is presented. This easy to use device allowed spectrophotometric and electroanalytical measurements to be performed simultaneously providing simultaneous information and enabling concomitant comparison and autovalidation of the results collected. The analytical robustness and precision of the proposed system was successfully tested on solutions containing mixtures of Patent Blue (E-131) and Brilliant Blue (Erioglaucine E-133), two food dyes displaying optical and redox properties very similar to each other.

Room temperature ionic liquids as useful overlayers for estimating food quality from their odor analysis by quartz crystal microbalance measurements.

An array of quartz crystals coated with different room-temperature ionic liquids (RTILs) is proposed for the analysis of flavors by quartz crystal microbalance (QCM) measurements. Seven RTILs were adopted as sensing layers, all containing imidazolium or phosphonium cations, differing from one another in the length and branching of alkyl groups and neutralized by different anions. The array was at first applied to the analysis of 31 volatile organic compounds (VOCs), such as alcohols, phenols, aldehydes, esters, ketones, acids, amines, hydrocarbons and terpenes, chosen as representative components of a wide variety of food flavors. Multivariate data analysis by the principal component analysis (PCA) approach of the set of the corresponding responses led to separated clusters for these different chemical categories. To further prove the good performance of the RTIL-coated quartz crystal array as an "electronic nose", it was applied to the analysis of headspaces from cinnamon samples belonging to different botanical varieties ( Cinnamon zeylanicum and Cinnamon cassia ). PCA applied to responses recorded on different stocks of samples of both varieties showed that they could be fully discriminated.

Pencil-drawn paper supported electrodes as simple electrochemical detectors for paper-based fluidic devices.

A simple procedure for preparing inexpensive paper-based three-electrode electrochemical cells is described here. They consist of small circular pads of hydrophilic paper defined by hydrophobic barriers printed on paper with wax-based ink. The back face of these pads is insulated by thermally laminating a polyethylene layer and working, reference and counter electrodes are drawn on paper by using commercial pencil leads. At last, a controlled volume of sample containing a supporting electrolyte was laid to soak in paper channels. Their performance was evaluated by assaying these devices as both simple cells suitable for recording voltammograms on static samples and low-cost detectors for flowing systems. Voltammetric tests, conducted by using potassium hexacyanoferrate(II) as model prototype, were also exploited for identifying the brand and softness of graphite sticks enabling paper to be marked with lines displaying the best conductivity. By taking advantage of the satisfactory information thus gained, pencil drawn electrodes were tested as amperometric detectors for the separation of ascorbic acid and sunset yellow, which were chosen as prototype electroactive analytes because they are frequently present concomitantly in several food matrices, such as soft drinks and fruit juices. This separation was performed by planar thin layer chromatography conducted on microfluidic paper-based devices prepared by patterning on filter paper two longitudinal hydrophobic barriers, once again printed with wax-based ink. Factors affecting both separation and electrochemical detection were examined and optimised, with best performance achieved by using a 20 mM acetate running buffer (pH 4.5) and by applying a detection potential of 0.9 V. Under these optimum conditions, the target analytes could be separated and detected within 6 min. The recorded peaks were well separated and characterized by good repeatability and fairly good sensitivity, thus proving that this approach is indeed suitable for rapidly assembling inexpensive and reliable electrochemical detectors for flow analysis systems.

Electrochemical gas sensors based on paper-supported room-temperature ionic liquids for improved analysis of acid vapours.

A prototype of a fast-response task-specific amperometric gas sensor based on paper-supported room-temperature ionic liquids (RTILs) is proposed here for improved analysis of volatile acid species. It consists of a small filter paper foil soaked with a RTIL mixture containing an ionic liquid whose anion (acetate) displays a basic character, upon which three electrodes are screen printed by carbon ink profiting from a suitable mask. It takes advantage of the high electrical conductivity and negligible vapour pressure of RTILs and of their easy immobilization into a porous and inexpensive supporting material such as paper. The performance of this device, used as a wall-jet amperometric detector for flow injection analyses of headspace samples in equilibrium with aqueous solutions at controlled concentrations, was evaluated for phenol and 1-butanethiol vapours which were adopted as model acid gaseous analytes. The results obtained showed that the quite high potentials required for the detection of these analytes are lowered significantly, thanks to the addition of the basic acetate RTIL. In such a way, overlap with the medium discharge is avoided, and the possible adverse effect of interfering species is minimised. The sensor performance was quite satisfactory (detection limits, ca. 0.3 µM; dynamic range, ca. 1-200 µM, both referred to solution concentrations; correlation coefficients in the range 0.993-0.997; repeatability, ± 6% RSD; long-term stability, 9%); thus suggesting the possible use of this device for manifold applications.

A modified electrode for the electrochemical detection of biogenic amines and their amino acid precursors separated by microchip capillary electrophoresis.

The use of a mixed-valent ruthenium oxide/hexacyanoruthenate polymeric film electrochemically deposited onto glassy carbon electrodes is proposed here for the detection of biogenic amines and their amino acid precursors, following their separation by microchip capillary electrophoresis. The ability of this ruthenium coating to electrocatalyze the oxidation of aliphatic and heterocyclic amines, as well as their amino acid precursors, was checked by using ethanolamine, tryptamine and tryptophane as prototype compounds and adopting a 25 mM sulphuric acid as the electrolyte in the detection cell, where a constant potential of 1.05 V versus Ag/AgCl, 3 M KCl was applied to the modified working electrode. Optimization of parameters affecting both detection and separation steps led to satisfactory separations when performed by using a 20 mM phosphate running buffer (pH 2.5) and applying a high voltage of 2.5 kV both in the separation and in the electrokinetic injection (duration 4 s). The recorded peaks were characterized by good repeatability (RSD ≤ 3.6%), high sensitivity and a wide linear range. Detection limits of 23 µM (1.4 mg/L), 27 µM (4.3 mg/L) and 34 µM (6.8 mg/L) were inferred for ethanolamine, tryptamine and tryptophane, respectively. The approach proposed here was also applied for the analysis of some double malt dark beers spiked with a controlled amount of the analytes considered.

A simple approach to the hydrodynamic injection in microchip electrophoresis with electrochemical detection.

A simple hydrodynamic injection method is proposed here for microchip CE coupled to electrochemical detection. It is based on the use of a precise syringe pump to push the sample into the microfluidic circuit, accompanied by the application of a secondary electric field to the injection channel, soon after the end of the injection step. In such a way, any counter pressure effect taking place when the sample plug enters the micrometric channel is prevented. Suitable optimization of this secondary electric field enables pushing of sample excess to be avoided and a narrow sample plug during the separation step to be maintained. Best conditions for hydrodynamic injection were achieved injecting catechol as model analyte by pressure with a syringe pump set at a flow rate of 8 microL/min for 6 s and applying to the injection channel a secondary high voltage of 700 V soon after the injection was completed. The reliability of this injection procedure has been proved by comparing electropherograms found for samples containing either catechol alone or catechol and dopamine together with those recorded under the same conditions by electrokinetic injection. Repeatability, expressed as RSD and estimated for seven replicate injections, turned out to be 2.1% for peak height of catechol used as single analyte and 0.9 and 1.1% for catechol and dopamine respectively, simultaneously injected.

Application of microchip electrophoresis with electrochemical detection to environmental aldehyde monitoring.

A method based on microchip electrophoresis with electrochemical detection has been developed for the simultaneous determination at trace levels of the main small-chain aldehydes (formaldehyde, acetaldehyde and 2-propenal) present in the atmosphere. Sampling was performed by forcing atmospheres through silica-gel cartridges coated with 2,4-dinitrophenylhydrazine (DNPH), where aldehydes were derivatized to form the corresponding hydrazones, which were then injected and eluted into the electrophoresis system. Factors affecting both separation and detection processes were optimized, with best performance achieved by applying a voltage of 2500 V both in the separation and in the electrokinetic injection (5 s) and using a 15 mM borate buffer (pH 9.2) added with 25 mM of SDS and 20% v/v ACN plus 10% v/v 1-propanol. Under these optimal conditions, well satisfactory resolution could be achieved, so that the analytes could be separated and detected within about 400 s, by applying a detection potential of - 1.0 V versus Ag/Ag/Cl to the glassy carbon-working electrode. The recorded peaks were characterized by both a good repeatibility (RSD <3%) and a linear dependence over a wide concentration range (2-100 microg/mL). Detection limits, estimated for a S/N of 3, equal to 9.5, 7.2 and 9.2 microM were inferred for the DNPH derivatives of formaldehyde, acetaldehyde, 2-propenal, respectively. The application of the method to aldehyde analysis in real air samples is also presented.

Electroanalytical cells pencil drawn on PVC supports and their use for the detection in flexible microfluidic devices.

A simple, effective and low-cost technique is here presented for assembling flexible and robust electrochemical devices on transparent PVC supports, using ordinary tools, all installed on a commercial desktop digitally controlled plotter/cutter. Small diamond burs were first set up to rough precise and well defined patterns on the surface of smooth and flexible PVC transparent films. Subsequently, reference, counter and working carbon electrodes were drawn onto abraded patterns by using micropencils (4B graphite leads, 0.5 mm in diameter), in their turn installed on the plotter/cutter. The effective active working surface of electrochemical cells was then defined by a thin adhesive strip or by covering the patterned support with a suitably cut adhesive layer, depending upon whether they were intended for use in batch or drop mode. After optimization of fabrication parameters, such as pressure and speed adopted during bur abrasion and pencil drawing, the electrochemical characterization of these cells was performed by using potassium hexacyanoferrate(II) as redox probe. Voltammetric responses displayed a good inter-device reproducibility (5.6%), thus confirming the effectiveness of this easy and fast assembling strategy. These PVC-based pencil-drawn electrochemical cells were then integrated as thin-layer detectors in adhesive-tape based microfluidic channels, cut and prepared in their turn using the digitally controlled plotter/cutter. These detectors offer the advantage given by the impermeability of PVC supports, thus avoiding absorption of the flowing carrier and consequent analyte broadening, instead occurring when electrochemical cells are pencil drawn on hydrophilic materials as paper. After optimization of the complete fabrication process, the effectiveness of these devices was tested by a proof-of-concept direct quantification of ascorbic acid in commonly used drugs.

Simultaneous determination of derivatized light aldehydes by microchip electrophoresis with electrochemical detection.

A method, based on microchip electrophoresis with electrochemical detection, has been developed for the simultaneous determination of light aliphatic aldehydes (acetaldehyde, propionaldehyde, butyraldehyde and hexylaldehyde) derivatized with 2,4-dinitrophenylhydrazine (DNPH). Optimal conditions for the derivatization reaction, providing recoveries of 70+/-1.8% for all analytes, were identified by application to real samples, consisting of vegetable oils enriched with known amounts of the aldehydes considered. DNPH hydrazones thus obtained in acetonitrile solution were added to the electrophoresis running medium consisting of a 15mM borate buffer (pH 9.2) added with 25mM of sodium dodecyl sulfate and 35% (v/v) of acetonitrile. Factors affecting both separation and electrochemical detection were examined and optimised, with best performance achieved by using the running medium above and applying a voltage of 2250V in both separation and electrokinetic injection. Under these optimal conditions, the target analytes could be separated and detected within 350s by applying a detection potential of -1.0V (vs. Ag/AgCl) to the glassy carbon working electrode. The recorded peaks were well separated and characterized by good repeatability (RSD=1.6-3.8%), high sensitivity and a wide linear range. Detection limits of 4.5, 6.6, 6.8, 13.1microM were obtained for acetaldehyde-DNPH, propionaldehyde-DNPH, butyraldehyde-DNPH and hexylaldehyde-DNPH derivatives, respectively.

A cotton thread fluidic device with a wall-jet pencil-drawn paper based dual electrode detector.

A simple and sensitive device is presented based on the use of pencil-drawn paper based electrochemical detector placed at the end of a cotton thread fluidic channel in wall-jet configuration. This innovative and fast responding electroanalytical system can be adopted for both single and dual electrode electrochemical detection, this last achieved by applying two different potentials at two independent working electrodes drawn on the opposite faces of the paper based detector. Its performance was preliminarily optimized by adopting hexacyanoferrate(II) as probe species undergoing reversible electrochemical processes. These devices were then used for the single electrode detection of ascorbic acid in aqueous samples and the dual electrode detection of orthodiphenols in extra virgin olive oils (EVOOs). In fact, these devices enable hydrophilic orthodiphenols, typically present in EVOOs (extracted by a 80:20% v/v acetonitrile/water mixture), to be discriminated from hydrophilic monophenols instead present in almost all vegetable oils. Flow-injections runs were conducted by using a 0.01 M H2SO4 + 0.5 KCl running electrolyte allowing the rapid and selective detection of hydrophilic orthodiphenols with satisfactory sensitivity and a low enough detection limit (2 µM). Different real samples of EVOOs and sunflower oils were analyzed. Abundant enough contents of orthidiphenols were found in EVOO samples, while no trace of these antioxidants was found in sunflower oils.

A paper-based platform with a pencil-drawn dual amperometric detector for the rapid quantification of ortho-diphenols in extravirgin olive oil.

A simple, sensitive and fast responding device is described for the discrimination of hydrophilic ortho-diphenols, whose presence in abundant enough amounts is typical for extra virgin olive oils (EVOOs), from hydrophilic mono-phenols instead present in almost all vegetable oils. It consists of a dual electrode detector pencil-drawn at the end of a paper microfluidic channel, defined by hydrophobic barriers, where samples of these antioxidants, extracted from vegetable oils by a 80:20% v/v acetonitrile/water mixture, were applied. Thin-layer chromatographic runs conducted by using a 0.01 M H2SO4 + 1 M KCl running buffer allowed the selective detection of hydrophilic ortho-diphenols by profiting from the fact that they undergo reversible oxidation at less positive potentials than those required by monophenols for displaying their irreversible anodic process. On this basis, a potential for the oxidation of hydrophilic ortho-diphenols was applied to the upstream pencil-drawn electrode (W1) (at which a minor fraction of mono-phenols was also oxidized), while a potential for the reverse process involving the sole product (ortho-quinones) of the reversible oxidation of ortho-diphenols was imposed at the downstream pencil-drawn working electrode (W2). Thus, cathodic peak currents linearly dependent on analyte concentrations could be recorded at W2 which led to a satisfactory detection limit (8 µM, equivalent to 1.23 mg/L) even when working electrodes W1 and W2 with same dimensions were employed. Improved sensitivities and lower detection limits were achieved by increasing the dimensions of W2 with respect to W1, thanks to the improvement of the collection efficiency. Throughout this investigation, hydroxytyrosol (HTy) and tyrosol (Ty) were adopted as models of ortho-diphenols and mono-phenols, respectively, in view of their abundant presence in EVOOs. Real samples of EVOO from different production companies, of a simple olive oil and of a sunflower oil were analyzed. Different hydrophilic ortho-diphenol contents were found in EVOO samples (up to 40.8 mg/kg), while only a negligible amount turned out to be present in simple olive oil. No trace of these antioxidants were instead found in sunflower oil, as expected. All concentrations found were in good agreement with those detected by a more frequently employed spectrophotometric method used for the sake of comparison.

Evaluation of chlorinated by-products in drinking waters of Central Friuli (Italy).

Drinkable water supplied by aqueducts undergoes preliminar potabilization which, in Italy, is mainly accomplished by chlorine addition. The bactericidal action involved in this process is always accompanied by chlorination and oxidation of organic species (mainly humic and fulvic acids) naturally present in treated waters, so that many disinfection by-products (DBPs) are formed, such as trihalomethanes (THMs) and halo-acetic acids (HAA), which can represent a chemical risk for public health. The aim of this study was the monitoring of DBPs in drinking water disinfected by chlorination, supplied by four different aqueducts of Central Friuli (Italy). DBP evaluations were performed in water samples consisting of both input and output of disinfection plants. The results of analytical determinations were worked out to provide the THM and HAA parameters for disinfected waters, while in feeding waters the following different conventional parameters were adopted: (i) trihalomethanes formation potential (THMFP), (ii) halo-acetic acids formation potential (HAAFP) and (iii) UV absorbance at 254 nm (UV254). The quite moderate content of chlorinated products found in all samples considered highlighted the excellent quality of potabilized waters available in Central Friuli. Moreover, our results confirmed that the majority of DBPs formed when chlorine is used for water disinfection consists of THMs, while chlorites and chlorates prevailed when potabilization is accomplished by using chlorine dioxide. Finally, simple UV254 monitoring turned out to be a profitable approach for the determination of chlorinated by-products only when THMs prevail among DBPs.

Quenching of superoxide ions by curcumin. A mechanistic study in acetonitrile.

The quenching of superoxide ions, O2.-, by curcumin has been studied by electrogenerating this anion radical from oxygen dissolved in acetonitrile solvent (that is, at best, a mimic of the lipofilic layer of biological membranes), containing known amounts of curcumin. Voltammetric tests, combined with coulometric and spectrophotometric measurements, pointed out that each mol of curcumin is able to react with six mols of such anion radical, through a process initiated by an acid-base step, which provides the perhydroxyl radical, HO2.; that disproportionates rapidly to the anionic form of hydrogen peroxide, HO2-, and oxygen, which is thus partially regenerated. At the same time, curcumin is converted to the corresponding three-charged anion. The strict resemblance existing between the mechanism of the rapid superoxide radical decay caused by curcumin and that involved in the presence of the superoxodismutase enzyme (SOD) is also underlined.

ICP-MS determination of toxic-metal release from pumping systems for food processing.

The release of heavy metals from uncovered and nickel-covered brass pumps has been evaluated by ICP-MS analysis in both simple ultrapure water and 3% acetic acid solution (mimic of neutral and acid edible liquids, respectively), following a procedure similar to that recommended by the National Sanitation Foundation (NSF) International, Test Procedure P203. The results found highlight that the main release regards zinc, copper and lead, i.e. the three major metals present in brass alloys. The first contact of brass surfaces with the extraction solvent leads to an extensive Pb release which is comparable with that observed for Cu and Zn. Subsequent washings reduce markedly the Pb release, thus rising in evidence a progressive surface passivation. In particular, the Pb release found after four repeated washings turns out to approach the limit set by both Italian and USA governments for liquids used for food purposes when determined in neutral media, while it remains quite higher when evaluated in acid media. Release analyses conducted on nickel-covered brass pumps point out that the Niploy nickel coating process is very effective for brass surface protection, in that the Pb release is reduced of about three orders of magnitude, but a Ni release exceeding the relevant permitted level is in this case observed.

An electrochemical gas sensor based on paper supported room temperature ionic liquids.

A sensitive and fast-responding membrane-free amperometric gas sensor is described, consisting of a small filter paper foil soaked with a room temperature ionic liquid (RTIL), upon which three electrodes are screen printed with carbon ink, using a suitable mask. It takes advantage of the high electrical conductivity and negligible vapour pressure of RTILs as well as their easy immobilization into a porous and inexpensive supporting material such as paper. Moreover, thanks to a careful control of the preparation procedure, a very close contact between the RTIL and electrode material can be achieved so as to allow gaseous analytes to undergo charge transfer just as soon as they reach the three-phase sites where the electrode material, paper supported RTIL and gas phase meet. Thus, the adverse effect on recorded currents of slow steps such as analyte diffusion and dissolution in a solvent is avoided. To evaluate the performance of this device, it was used as a wall-jet amperometric detector for flow injection analysis of 1-butanethiol vapours, adopted as the model gaseous analyte, present in headspace samples in equilibrium with aqueous solutions at controlled concentrations. With this purpose, the RTIL soaked paper electrochemical detector (RTIL-PED) was assembled by using 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide as the wicking RTIL and printing the working electrode with carbon ink doped with cobalt(II) phthalocyanine, to profit from its ability to electrocatalyze thiol oxidation. The results obtained were quite satisfactory (detection limit: 0.5 µM; dynamic range: 2-200 µM, both referring to solution concentrations; correlation coefficient: 0.998; repeatability: ±7% RSD; long-term stability: 9%), thus suggesting the possible use of this device for manifold applications.

A sensor based on electrodes supported on ion-exchange membranes for the flow-injection monitoring of sulphur dioxide in wines and grape juices.

A sensitive and fast responding electrochemical sensor is described for the determination of free and total sulphur dioxide in wines and grape juices which prevents interferences coming from ethanol and other natural components. It consists of a cell provided with a porous gold working electrode supported on one face of an ion-exchange membrane, acting as a solid polymer electrolyte (SPE), which allows gaseous electroactive analytes to be detected. This sensor was used as an amperometric detector for a flow injection system in which controlled volumes of headspace equilibrated with samples were injected. This approach was adopted to make also possible the determination of total SO(2), avoiding drawbacks caused by the high relative humidity generated by the sample heating resulting from the neutralization reaction of excess NaOH, whose addition was required to release sulphur dioxide from its combined forms. Factors affecting the detection process were examined and optimised. Under the identified optimal conditions, SO(2) detection resulted in sharp peaks which allowed to infer detection limits for a signal-to-noise ratio of 3, referred to liquid samples, of 0.04 and 0.02 mg L(-1) for free and total SO(2) which were determined at 20 and 35 degrees C, respectively. Moreover, the responses were found to be characterized by good repeatability (+/-2% and +/-4%, respectively) and linear dependence on the SO(2) concentration over a wide range (0.2-500 mg L(-1) for both free and total SO(2)). Finally, the long-term stability of the sensor turned out to be totally satisfactory in that responses changed of +/-9% alone even after long periods of continuous use. The application to some commercial wines and grape juices is also presented.

Rapid analysis of azo-dyes in food by microchip electrophoresis with electrochemical detection.

A method based on microchip electrophoresis with electrochemical (EC) detection has been developed for the simultaneous determination of Yellow AB, Red 2G, Sunset Yellow, New Coccine, and Amaranth which are azo-dyes frequently added to foodstuffs. Factors affecting both separation and detection processes were examined and optimized, with best performance achieved by using a 10 mM phosphate buffer (pH 11) as BGE solution and applying a voltage of 2500 V both in the separation and in the electrokinetic injection (duration 4 s). Under these optimal conditions, the target dye analytes could be separated and detected within 300 s by applying a detection potential of -1.0 V (vs. Ag/AgCl) to the glassy carbon (GC) working electrode. The recorded peaks were characterized by a good repeatability (RSD=1.8-3.2%), high sensitivity, and a wide linear range. Detection limits of 3.8, 3.4, 3.6, 9.1, 15.1 microM were obtained for Yellow AB, Red 2G, Sunset Yellow, New Coccine, and Amaranth, respectively. Fast, sensitive, and selective response makes the new microchip protocol very attractive for the quantitative analysis of commercial soft drinks and candies.